FAAC CVX-1300 User Manual

CVX-1300

Operations Manual

DataBender™ Universal Format Converter

CVX-1300_MAN_112011

Data I/O

Reader - Wiegand, Strobed (Clock & Data), F/2F

LED - 0 to 30v

Interface

+5vDC @ 100 ma

Output

95% (non-condensing)

Storage (-55°C to +150°C)

Operating (-40°C to +80°C*)

Power

Unreg Input 8 to 16VDC* @ 200ma Max

Input

Humidity

Aluminum enclosure

Size 3.5” x 2.75” x .75”

Temp

Physical

3.3”

DataBender CVX-1300

2.8”

1.4”

3.65”

ø 0.15”

External Dimensions and Mounting Holes

Unit Height = 0.75”

Electrical and Mechanical Speciﬁcations

* See notes on following page for temperature and power ratings

This complies with part 15 of the FCC rules

Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Cypress Computer Systems, Inc. ⌖ Lapeer, MI 48446 ⌖ www.cypresscomputer.com

Initial Setup - CVX-1300 Converter

The CVX-1300 will support many different input and output formats.

The CVX-1300 replaces the CVX-1200 and many of the standard Cypress CVT series of converters (e.g. CVT-2232 CVT-9102).

A DIP switch determines which conversion process will be used.

A “Legacy” cross reference chart is provided to quickly determine which settings to use for standard Cypress converter numbers. In most cases several baud rate options are available to expand the capabilities of existing converters. The Legacy cross reference chart will list the converter CVT number and the CVX numbers and the DIP switch setting that will apply. Use the converter numbers to ﬁnd the DIP switch settings on the CVX-1300 application charts.

Setting up the CVX-1300 converter:

1. First determine which converter (conversion process) is required for the application. This may be one of the standard Cypress converters or one of the new converters that are now part of the CVX-1300 library. All of the different conversion processes are described in detail in this manual. Each process will have a wiring diagram and speciﬁcation sheet to describe the wiring connections and operation.

2. Set the DIP switch to the setting called out in the CVX application chart.

3. Refer to the wiring diagram for the particular converter that is being used. The wiring diagrams are different depending upon the type of conversion being performed.

4. Connect power to the CVX-1300 board.

5. If the diagnostic indicator LED ﬂashes Green slowly, a valid converter number has been selected. If the diagnostic indicator is illuminated a solid Red color, an invalid DIP switch setting has been made.

6. Connect peripheral devices (Readers, Panel, Switches etc.) according to the appropriate wiring diagram.

LEGACY CONVERTER EXAMPLE: You need a CVT-2232 that operates at 2400 Baud.

The Legacy Compatibility chart calls out CVX numbers 1,2, and 3.

Looking at the CVX application charts for #1,#2,and #3 lists 3 baud rates. Selecting the 2400 Baud rate for CVX converter #2 would yield a DIP switch setting of: 1 OFF, 2 ON , 3 OFF, 4 OFF, 5 OFF, 6 OFF, 7 OFF, 8 OFF

The wiring diagram would reference the Wiegand to Serial connections.

NOTE: The CVX-1300 does not use an onboard DB type connector for RS-232 serial signals. Serial connections can be made directly to the 12 position connector. An optional patch cord is available with a Female DB-9 connector and ﬂying leads. The wiring diagrams indicate the equivalent DB-9 connections to the CVX-1300 J3 connector.

Electrical and Environmental Speciﬁcations

810121416805535-40

Ambient Temperature

(Degrees Celsius)

Supply Voltage

Temperature/Voltage de-rating curve

Converter CVX-1300

CYPRESS

The CVX-1300 units should be operated with a ﬁltered 12 Volt nominal DC supply. Any voltage between 8 and 16 volts can be utilized by following the temperature /voltage derating curve. Voltage should not exceed 16 VDC under normal operating conditions.

1-D0/CLK Input 2-D1/Data Input 3-Aux2 LED Out 4-Ground 5-RS232 Input 6-RS232 Output 7-RLY1 N.C. 8-RLY1 Com 9-RLY1 N.O. 10-RLY2 N.C. 11-RLY2 Com 12-RLY2 N.O.

1-D0/CLK Output

2-D1/Data Output

3-Aux1 LED In

4-Analog In1 5-Analog In2

6-+5 VDC Out

7-RS485 (-)

8-RS485 (+)

Ground

+8 to +16 VDC In

DC Power IN

External connections and product description

Converter CVX-1300

1-D0/CLK Input 2-D1/Data/F2F Input 3-Aux2 LED Out 4-Ground 5-RS232 Input 6-RS232 Output 7-RLY1 N.C. 8-RLY1 Com 9-RLY1 N.O. 10-RLY2 N.C. 11-RLY2 Com 12-RLY2 N.O.

Note: F2F connections support unsupervised mode

1-D0/CLK Output 2-D1/Data/F2F Output 3-Aux1 LED In 4-Analog In1 5-Analog In2 6-+5 VDC Out 7-RS485 (-) 8-RS485 (+)

Diagnostic LED

1-Ground 2-8 to 16 VDC In

Note: Terminals shown for reference. Connections may or may not be utilized based on converter function.

The Cypress CVX-1300 is based on the CVX-1200 series converter. For most legacy converter functions, the DIP switch settings will be set the same as with the Cypress CVX-1200.

This document provides detailed wiring information and a reference to DIP switch settings for the converter. Detailed conversion descriptions are provided in chapters organized for each type of conversion function. i.e. Wiegand to Serial functions will have a chapter, Serial to Strobed will have a chapter etc. Each chapter is a separate document and is available at www.cypressoworld.com

A Diagnostic LED is provided to provide operational status of the converter:

Diagnostic LED OFF - No power

Diagnostic LED Blinking Green - Unit is operating

Diagnostic LED Red - Undeﬁned DIP Switch Setting

CVX-1300 Serial data and RS485

Converter CVX-1300

CYPRESS

The CVX-1300 can support both RS-232 and RS-485 signals for transmitting and receiving serial data. For most converters utilizing serial data, both interfaces are always active and may be used by making the appropriate connections to the converter. Either the RS-232 or RS-485 interface may be used, but a loss of data will occur if both interfaces have active data at the same time.

Examples:

The CVT-2232 function will provide a serial input and convert to a Wiegand output. Serial data can be read from either the RS-232 or RS-485 interface. The baud rate will be determined by the DIP switch setting.

The CVT-9110 function will provide a Wiegand input and a serial output. Serial data will be output on the RS-232 and RS-485 interface.

NOTE: Some of the CVX-1300 converters may not support both RS-232 and RS-485 interfaces. Converters that do not support both interfaces will be noted in the speciﬁc converter speciﬁcation.

RS-232 Interface

1-D0/CLK Input 2-D1/Data Input 3-Aux2 LED Out 4-Ground 5-RS232 Input 6-RS232 Output 7-RLY1 N.C. 8-RLY1 Com 9-RLY1 N.O. 10-RLY2 N.C. 11-RLY2 Com 12-RLY2 N.O.

1-D0/CLK Output

2-D1/Data Output

3-Aux1 LED In

4-Analog In1 5-Analog In2

6-+5 VDC Out

7-RS485 (-)

8-RS485 (+)

1-Ground

2-8 to 16 VDC In

RS-485 Interface

This Page left intentionally blank

Converter

Input

Output

Settings(#)

CVT2232

Wiegand 24 to 40

Serial 13 Digits with <CR>

1 , 2 , 3

CVT-2111

Wiegand 1 to 40

Serial Dec/Hex Digits

7, 8, 9

CVT-2110

Wiegand 1 to 48

SerialHex Digits

10 , 11, 12

CVT-2144

Wiegand 44

Serial12 Digits

13 , 14 , 15

CVT-2145

Wiegand 44/32

Serial 12/10 Digits

16 , 17 , 18

CVT-2152

Wiegand 1 to 96

Serial 24 Hex Dec

19 , 20 , 21

CVT-2151

Wiegand 1 to 40

Serial HID Hex

22 , 23 , 24

CVT-2201

Strobed/ABA

Serial 24 Hex

25 , 26 , 27

CVT-2403

F/2F Raw

Serial ASCII Hex

CVT-2404

F/2F ABA

Serial ASCII Hex

CVT-2405

F/2F ABA

Wiegand 37 bit Custom

CVT-2406

F/2F ABA

Wiegand 37 bit Custom

CVT-9102

Serial 10 Dec

Wiegand 26

65 , 66 , 67

CVT-9110

Serial 12 Hex

Wiegand Variable

68 , 68 , 70

CVT-9109

Serial Transcore

Wiegand 26

CVT-9129

Serial Transcore

Xico 6

CVT-9132

Serial Transcore

Wiegand 37

CVT-9137

Serial Transcore

Wiegand 26

CVT-9117

Serial Transcore

Wiegand 26

CVT-9161

Serial Transcore

Wiegand 26

CVT-9162

Serial Transcore

Wiegand 37

CVT-9164

Serial Transcore

Wiegand 37

CVT-9201

Serial ASCII

Strobed / ABA

79,80,81,82

CVT-5932

Dallas iButton 1Wire

Wiegand 26

CVT-9165

Serial Transcore 26 bit

Wiegand 26

CVT-0026

Wiegand 24-40 bit

Wiegand 26

CVT-0026A

24-40 bit, spec 34 bit pr.

Wiegand 26

CVT-3526

Wiegand 35 bit C1000

Wiegand 26

CVT-5100

12 digit Strobed ABA

Wiegand 26

100

CVT-5100A

Last 8 digit Strobed ABA

Wiegand 26

101

CVT-5200

Wiegand 26 and 35 bit

12 Digit Strobed/ABA

102

CVX-1300 Legacy Compatable formats

Converter

Input

Output

Settings(#)

CVT-5201

Wiegand 26 bit

10 digit Strobed/ABA

103

CVT-2211

Wiegand ABA

Serial ASCII

35,36

CVT-0126

Wiegand 26 bit

Wiegand 26 bit ﬁxed FC=215

104

CVT-9117A

Serial Transcore

Wiegand 26

CVT-3226

Wiegand 32 Bit Kastle

Wiegand 26 bit Standard

105

CVT-9133

Serial ASCII

Wiegand 36 bit Special

CVT-9501

Serial ASCII 1-12 digits

F/2F

CVT-2485

Wiegand 24-40

Serial ASCII RS-485

1,2,3

CVT-9485

Serial ASCII RS-485

Wiegand 24-40

65,66,67

CVT-2201F

Strobed/ABA Fall Edge

Serial 24 Hex

CVT-5100F

Strobed/ABA Fall Edge

Wiegand 26 bit

106

CVT-5100AF

Strobed/ABA Fall Edge

Wiegand 26 bit

107

CVX-2232-5

Wiegand 24-40

Serial- Last 5 digits

CVX-9174

Serial ASCII 1-10 Dec

Wiegand 37 Bit FC = 1

CVT-0126B

Wiegand 26 bit

Wiegand 26 bit ﬁxed FC=0

108

CVT-5217

Wiegand 24-40

8 digit Strobed/ABA

112

CVX-1300 Legacy Compatable formats

+ 19 hidden pages