Epson XP-800 Small-in-One Start Here Manual

*412324700*

XP-800 Small-in-OneTM Printer

Start Here

Read these instructions before using your product.

Note for Spanish speakers/Nota para hispanohablantes:

Para obtener instrucciones de configuración en español, consulte la Guía de instalación en www.epson.com/support/xp800sp (requiere una conexión a Internet).

3 Press the power button, then adjust the

control panel

Select settings

1 Select your language and country.

Unpack

Caution: Do not open ink cartridge packages until you are ready to

install the ink. Cartridges are vacuum packed to maintain reliability.

1 Remove all protective materials from the printer,

including from inside the printer.

Touch the screen to select the desired option. Press

or to see more countries.

2 Select Summer if Daylight Saving Time is in effect

(spring through summer); otherwise, select Winter.

3 Select the date format.

4 Use the numeric keypad to set the date, then press

Done.

5 Select the time format (12h or 24h).

6 Use the numeric keypad to set the time.

7 Press Done when ﬁnished.

Note: You can change the date and time settings using the product’s

control panel. For more information, see the online User’s Guide.

Install ink cartridges

1 Lift up the scanner unit.

2 Lower the scanner unit.

Turn on and adjust

1 Connect the power

cord to the back of the printer and to an electrical outlet.

Caution: Do not connect

to your computer yet.

2 To load legal-size paper in the ADF,

you will need to place the printer with its right side at least 4 inches (10 cm) away from the wall or any other objects.

2 Gently shake the BK (black) ink cartridge only. Do not

shake the PBK (photo black) cartridge or any of the other color ink cartridges. Unpack the ink cartridges.

Caution: Do not touch the areas shown below. Doing so may

prevent normal operation and printing.

3 Remove the cap from each ink cartridge. Store the caps

in the included plastic bag.

2 Pull on the front cover to pull out the lower paper

cassette.

lower cassette

Note: Save the caps and use them to recap the ink cartridges

after removing them for storage or disposal.

4 Insert the cartridges head ﬁrst in the holder for each

color. Press each cartridge down until it clicks.

5 Lower the scanner unit.

6 The printer starts priming the ink. This takes about 6

minutes. When you see a completion message on the printer’s LCD screen, priming is complete.

Note: The cartridges included with the printer are designed

for printer set up and not for resale. After some ink is used for priming, the rest is available for printing only in the same printer.

Caution: Don’t turn off the printer or raise the scanner unit

while the printer is priming or you’ll waste ink.

3 Slide the edge guides to the sides of the paper cassette.

4 Set the front edge guide to the paper size you are using.

Then insert paper with the glossy or printable side facedown.

Note: Make sure the paper is loaded against the edge guide

and not sticking out from the end of the cassette.

5 Slide the edge guides against the paper, but not too

tight. Make sure the paper is under the tabs on the edge guides.

Load paper

The printer has 2 paper cassettes and a rear paper feed slot. You can load the following paper sizes:

• Upper cassette (Cassette 1): 4 × 6- or 5 × 7-inch photo paper.

• Lower cassette (Cassette 2): letter-size, A4, legal-size, or 8 × 10-inch paper. (See the instructions below for loading paper in the lower cassette.)

• Rear paper feed slot: one sheet at a time

See the upper cassette and rear paper feed slot. See the online User’s Guide for available paper types, sizes, loading capacity, and instructions for loading legal-size paper, envelopes, and card stock.

Quick Guide for instructions on loading paper in the

1 Lower the front cover (if it’s not open already).

6 Keep the cassette ﬂat as you insert it.

Note: The output tray will open automatically when you print.

+ 2 hidden pages