With a permanent installation design oering easy setup and maintenance, this
projector is a perfect addition to any conference room or classroom. Oering bright,
vivid images and a wide functionality including easy network projection and split
screen.
Audio input portsStereo mini × 3, RCA (L-R) × 1
Audio output portsStereo mini × 1
Control portsRJ45 × 1, Mini D-Sub 9 pin × 1 (RS-232C), Stereo mini × 1 (for wired remote control)
Speaker10 W (monaural)
Functions
EB-
4955WU
3
409 W (Power
Consumption Normal),
311 W (Power
Consumption ECO)
388 W (Power
Consumption Normal),
298 W (Power
Consumption ECO)
USB connector (A type) × 1 (dedicated Wireless LAN unit*4 supporting IEEE802.11b/g/n)
Schedule, Geometric correction function, Split screen, Freeze, A/V mute, Help function,
Color mode, Password protection, Auto source search, User's logo, Memory function,
Control panel lock, Direct power on, Direct shutdown, Network projection function
EB-
4950WU
4.3 W (Communication On),
0.38 W (Communication O)
4.6 W (Communication On), 0.47 W
(Communication O)
4.6 W (Communication On), 0.39 W
(Communication O)
EB-
4650
EB-
4550
387 W (Power
Consumption
Normal),
311 W (Power
Consumption
ECO)
368 W (Power
Consumption
Normal),
298 W (Power
Consumption
ECO)
*1 Measurement, measuring conditions, and method of notation all comply with ISO 21118 international
standards.
*2
The position of the image cannot be moved to both the horizontal and vertical maximum values simultaneously.
*3 The operating temperature is 0 to +45°C when Power Consumption is set to ECO or Temp Interlock and
0 to +40°C when it is set to Normal at an altitude of 0 to 1499 m.
The operating temperature is 0 to +40°C when Power Consumption is set to ECO or Temp Interlock and
0 to +35°C when it is set to Normal at an altitude of 1500 to 3048 m.
*4 The Wireless LAN unit is an optional accessory.
Ceiling Mount (Optional Accessories)
A dedicated ceiling mount is required when suspending the projector from a ceiling.
ProductPart NumberMass
Ceiling MountELPMB223.5 kg
Ceiling pipe (450 mm) ELPFP132.1 kg
Ceiling pipe (700 mm) ELPFP142.6 kg
Page 5
Dimensions
472
236
250151
32275.5
288.5
134
73
71.7190
54.7221
10
232
180
76
159
354
320
Units: mm
Lamp cover
Wireless LAN unit
installation section
5
Page 6
6
200
41 41
18˚18˚
41 41
160
46
758080
472
161161
38433
305
122
223
150
157
8080
4-14
127
188
Ø48.4
Ø48.6
200
4-16
Dimensions with Ceiling Mount ELPMB22
Align the center of the projector lens and the center of the
ceiling mount ELPMB22. (See gure on right)
Units: mm
Scale sticker
Lens alignment
screws
Vertical
adjustment axis
Page 7
Dimensions with ELPMB22 and ELPFP13 (Ceiling Pipe 450 mm)
41 41
160
472
161161
8080
4-14
188
200
4-16
46
6067
718 (668~868)155
135738285
50
307
50 50 50 50115
46
160
41 41
200
808075
25
25
38433
122
Scale sticker
Align the center of the projector lens and the center of the
ceiling mount ELPMB22. (See gure on right)
Units: mm
Lens alignment
screws
Make sure to
secure with two
penetrating
screws and nuts.
Vertical
adjustment
axis
7
Page 8
8
Dimensions with ELPMB22 and ELPFP14 (Ceiling Pipe 700 mm)
41 41
160
472
161161
8080
4-14
188
200
4-16
46
6067
1018 (918~1118)155
13585
607
50 50 50 50 5011546
25
25
7382
160
41 41
200
808075
38433
122
Units: mm
Scale sticker
Lens alignment
screws
Align the center of the projector lens and the center of the
ceiling mount ELPMB22. (See gure on right)
Make sure to
secure with two
penetrating
screws and nuts.
Vertical
adjustment
axis
Page 9
Interface
EB-4955WU/EB-4950WU/EB-4855WU/EB-4850WU
EB-4750W/EB-4650/EB-4550
NoNameNoName
Audio1 port (stereo mini)
A
Computer port (mini D-Sub 15 pin)
B
BNC port (5BNC)
C
Monitor Out port*1 (mini D-Sub 15 pin)
D
Audio Out port (stereo mini)
E
RS-232C port (mini D-Sub 9 pin)
F
Remote port (stereo mini)
G
Audio2 port (stereo mini)
H
Audio-L/R port (RCA × 2)
I
S-Video port (mini DIN 4 pin)
J
Video port (RCA)
K
HDMI port (HDMI)
L
Audio3 port (stereo mini)
M
DisplayPort (DisplayPort)
N
LAN port (RJ45)
O
Service port*
P
2
*1 Only analog RGB signals can be output from the BNC and Computer ports.
*2 This is for maintenance personnel and should not normally be used.
9
Page 10
10
Remote Control Operating Range
Horizontal
Vertical
Page 11
Screen Size and Projection Distance
See pages 6 to 8 for the distances from the ceiling plate to each part of the projector.
From center of lens to bottom of screen: (B1) = Screen size × 0.27765
(B2) = Screen size × 1.62385
Page 13
Projection Distance Table
The projection distances are approximate values.
Visit the following Web site to nd the projection distance calculator.
http://www.epson.com/alf_upload/landing/distance-calculator/
Only compatible when Wide is selected as the
Resolution from the Conguration menu.
(This is not available for EB-4650/EB-4550.)
*2 EB-4955WU/EB-4950WU/EB-4855WU/
EB-4850WU only. Only compatible when VESA
CVT-RB (Reduced Blanking) signal is input.
Refresh Rate (Hz)
56/60/72/75/85
601280×768
601366×768
60/75/851280×800
70/75/851152×864
60/75/851280×1024
60/75/851280×960
1
2
601680×1050
601920×1200
75 1024×768
591024×768
75 1152×870
Resolution (Dots)
800×600
Component Video
Signal
SDTV (480i)60720×480
SDTV (576i)50720×576
SDTV (480p)60720×480
SDTV (576p)50720×576
HDTV (720p)
HDTV (1080i)
HDTV (1080p)*
*
EB-4955WU/EB-4950WU/EB-4855WU/EB-4850WU
only.
Refresh Rate (Hz)
50/601280×720
50/601920×1080
50/601920×1080
Resolution (Dots)
Composite Video
Signal
TV (NTSC)60720×480
TV (SECAM)50720×576
TV (PAL)50/60720×576
Refresh Rate (Hz)
Resolution (Dots)
Page 23
Input Signals from the HDMI Port
and the DisplayPort (EB-4955WU/
EB-4950WU/EB-4855WU/
EB-4850WU/EB-4750W)
Signal
VGA 60 640×480
SVGA 60800×600
XGA601024×768
WXGA
WXGA+601440×900
WXGA++601600×900
WSXGA+601680×1050
SXGA
SXGA+601400×1050
UXGA 601600×1200
WUXGA*
SDTV
(480i*3/480p)
SDTV
(576i*3/576)
HDTV (720p)
HDTV (1080i)50/601920×1080
HDTV (1080p)24*3/30*3/50/601920×1080
*1 DisplayPort input only
*2 EB-4955WU/EB-4950WU/EB-4855WU/
EB-4850WU only. Only compatible when VESA
CVT-RB (Reduced Blanking) signal is input.
*3 HDMI input only
Refresh Rate (Hz)
2
Resolution (Dots)
601280×800
601280×768*
601366×768
601280×960
601280×1024
601920×1200
60720×480
50720×576
50/601280×720
1
Input Signal from the HDMI Port
and DisplayPort (EB-4650/EB-4550)
Signal
VGA 60 640×480
SVGA 60800×600
XGA601024×768
WXGA
WXGA+601440×900
WXGA++601600×900
SXGA
SXGA+601400×1050
UXGA 601600×1200
SDTV
(480i*2/480p)
SDTV
(576i*2/576p)
HDTV (720p)50/601280×720
HDTV (1080i)50/601920×1080
HDTV (1080p)24*2/30*2/50/601920×1080
*1 DisplayPort input only
*2 HDMI input only
Refresh Rate (Hz)
601280×800
601280×768*
601366×768
601280×960
601280×1024
60720×480
50720×576
Resolution (Dots)
1
23
Page 24
24
Lens Shift Adjustment Range
1
2
EB-4955WU/EB-4950WU/EB-4855WU/EB-4850WU
EB-4750W/EB-4650/EB-4550
Center of lens
Projected image when lens shift is
set in the center
Center of lens
Projected image when lens shift is
set in the center
Maximum range
EB-4750W: V × 70%
EB-4650/EB-4550: V × 58%
When horizontal lens shift is set to the maximum
EB-4750W: V × 60%
EB-4650/EB-4550: V × 50%
The position of the image cannot be moved to both the horizontal and vertical
maximum values simultaneously.
Page 25
Installation Environment
The projector can be installed at the following angles.
Vertical: Tilt up to ±30°. If you use the projector tilted at an angle of more than 30° it
could be damaged and cause an accident.
Horizontal: Can be tilted within the range of expansion and contraction for the rear feet.
When installing the projector, make sure there is a gap of at least 50 cm between the
wall and the air exhaust vent and the air intake vent.
When setting up multiple projectors, make sure there is a gap of at least 50 cm
between the projectors. Also, make sure that heat from the air exhaust vent is not taken
in by the air intake vent.
Do not stack projectors
directly on top of each other.
Do not stand the projector on its side and project.
25
Page 26
26
Serial Connection
<At the projector><At the computer>
<At the projector><At the computer>
Serial cable (cross)
Serial port specications
Connector shape: D-Sub 9-pin (male)
Projector input port name: RS-232C
Communication specications
• Default baud rate setting: 9600 bps
• Data length: 8 bit
• Parity: None
• Stop-bit: 1 bit
• Flow control: None
Page 27
Monitoring and Control
The projector can be monitored and controlled using the following methods. For more
details, see the "User's Guide" supplied with the projector.
ESC/VP21 commands
•
When the projector is connected to a computer with an RS-232C cable, you can control
the projector with communication commands.
Web control
•
By using the Web browser of a computer connected to the projector on a network, you
can make settings and control the projector.
PJLink commands
•
The projector complies with the PJLink Class1 standard established by the JBMIA. From
a computer connected to the projector on a network, you can control the projector
with PJLink commands.
For more details on PJLink, see the following Web site.
http://pjlink.jbmia.or.jp/english/
EasyMP Monitor (Software provided by Epson)
•
Allows you to control multiple Epson projectors on a network.
You can download EasyMP Monitor from the following Web site.
http://www.epson.com
Crestron RoomView®
•
This projector supports the control protocol provided by Crestron®. From a computer
connected to the projector on a network, you can control the projector.
27
Page 28
28
ESC/VP21 Command List
When the power ON command is transmitted to the projector, the power turns on and
it enters warm-up mode. When the projector's power has turned on, a colon ":" (3Ah) is
returned.
When a command is input, the projector executes the command and returns a ":", and
then accepts the next command.
If the command being processed terminates abnormally, an error message is output
and a ":" is returned.
Power on/o
FunctionCommand
Power onPWR ON
Power oPWR OFF
Power status queryPWR?00Standby status
01Projecting status
02
03Cooling status
04Network monitoring status/communication status
05Error standby status
09
Warm-up status
Standby status (external output of images and audio is possible)
Content
Setting
Value/
Response
Content
Value
14ComputerComponent
1FComputerAuto
30HDMI
40Switch Video and S-Video
41Video
42
53LAN
70DisplayPort
B0BNC5BNC
B1BNCRGB
B4BNCComponent
F0Switch to all input sources in order
F1Switch to Computer, BNC, DisplayPort, and LAN in order
F2
S-Video
Switch to S-Video, Video, and HDMI in order
Page 29
Conguration menu
INC: Increase the setting value/DEC: Decrease the setting value/INIT: Return to defaults
Displays a list of the available input
sources of the projector.
"0" is displayed when no error has
occurred.
Does not support video mute
o/on (10/11) or audio mute
o/on (20/21).
Network - Basic - Projector Name
from the projector's Conguration
menu.
Page 37
Product name
information
query
Class information
query
• The password for PJLink is set in Network-Basic-PJLink Password from the projector's Conguration
menu. If you do not want to use a password, leave PJLink Password blank.
• PJLink trademark is a trademark applied for registration or is already registered in Japan, the United States
of America and other countries and areas.
All rights reserved. No part of this publication may be reproduced, stored in a
retrieval system, or transmitted in any form or by any means, electronic, mechanical,
photocopying, or otherwise, with out the prior written permission of SEIKO EPSON
CORPORATION.
No patent liability is assumed with respect to the use of the information contained
herein. Neither is any liability assumed for damages resulting from the use of the
information contained herein.
Neither SEIKO EPSON CORPORATION nor its aliates shall be liable to the purchase
of this product or third parties for damages, losses, costs, or expenses incurred by
purchaser or third parties as a result of: accident, misuse, or abuse of this product
or unauthorized modications, repairs, or alterations to this product, or (excluding
the U.S.) failure to strictly comply with SEIKO EPSON CORPORATION’s operating and
maintenance instructions.
SEIKO EPSON CORPORATION shall not be liable against any damages or problems
arising from the use of any options or any consumable products other than those
designated as Original EPSON Products or EPSON Approved Products by SEKO EPSON
CORPORATION.
EPSON is a registered trademark of SEIKO EPSON CORPORATION.
General Notice
Other product names used herein are also for identication purposes only and may be
trademarks of their respective owner. EPSON disclaims any and all rights in those marks.