Emerson LK65 Owner's Manual

WARNING: Over lamping the light kit result
with a blown fuse. Before replacing the fuse,
shut off the electrical supply at the main fuse
box or circuit breaker panel. The fuse is loca­ ted on the top surface of the light kit housing.
Replacement fuse shall be rated 125VAC, and

1.25A. Do do exceed the 1.25A maximum curr­ ent rating. Replace the old lamps with new 60W
maximum candelabra lamps. Restore electrical
power to the light kit at the main fuse box or
circuit breaker panel.

the

LK65

2.47

BP7406

74060000

1/09

09/09

74060000

BP7406

LK65

Safety Instructions

WARNING: To avoid fire, shock, and serious personal injury, follow all

instructions carefully.

1. Read your Owner's Manual carefully before installing the light fixture.
Retain Owner's Manual for future reference.

2. Be careful of the fan and blades when cleaning, painting, or working near
the fan. Before installing or servicing the light fixture or ceiling fan, switch
power off at service panel and lock service panel disconnecting means to
prevent power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a warning device,
such as a tag, to the service panel.

3.Do not exceed the wattage indicated on fixture (two 60-watt candelabra base
bulbs maximum).

ADDITIONAL SAFETY INSTRUCTIONS FOR INSTALLATION

1. To avoid possible electrical shock, be sure electricity is turned off at the
main fuse or circuit breaker box before wiring.

2.Make certain no bare wires are exposed outside the wire connectors.

3.All wiring must conform to National and Local Electrical Codes.

4.Follow the recommended instructions for the proper method of wiring your
new light fixture. If you feel you do not have enough electrical wiring
knowledge or experience, have your fixture installed by a licensed
electrician. Any electrical work not described in this manual should be
performed by a licensed electrician.

WARNING: To reduce the risk of possible fire and electrical shock, install
only on Emerson CF and F Series Ceiling Fans. This light fixture is not

to be
used with CF652, CF653, CF670, CF680, CF742, and CF2000 Series Ceiling
Fans installed in damp or wet locations.

2

1.Remove the cover from the switch
housing below ceiling fan. Replace the
screws loosely in the switch housing.
Do not tighten. (Figure 4.)

2.Carefully pull down white and blue
wires from the switch housing and
remove wire connectors.

Do not install or use the light fixture
if any part is missing or damaged.
Contact your dealer for replacement.

WARNING

To avoid possible electrical shock,
be sure electricity is turned off at the
main fuse or circuit breaker box
before wiring.

WARNING

Installation on Emerson Fans Having a Modular

Switch Cup with Center Screw

Do not install or use the light fixture
if any part is missing or damaged.
Contact your dealer for replacement.

WARNING

To avoid possible electrical shock,
be sure electricity is turned off at the
main fuse or circuit breaker box
before wiring.

WARNING

1.Remove the switch cup from the cover
plate by removing the three screws
around the side of the switch cup
(Figure 1).

2.Disconnect the motor connector from
the switch cup connector.

Figure 1

3.Remove the center screw from the
switch cup (Figure 1).

4.Carefully locate the white and blue
wires (labeled either "L" or "LIGHT") in
the switch cup and remove the wire
connectors from the wires.

5.Install the black and white wires from
the light fitter and thread the switch cup
onto the light fitter. Hold wires taut
while installing switch cup to prevent
the wires from twisting. Install and
tighten the lockwasher and nut onto the
fitter (Figure 2).

6.Position the light fitter so that the chain
bushing in the light fitter aligns with the
pull chain in the switch cup (Figure 2).

7.Connect the white wire from the switch
cup to the white wire of the light fitter
(Figure 2). Connect the blue wire from
the switch cup to the black wire of the
light fitter. Use listed wire connectors
(previously removed in Step 4) to make
connections (Figures 2 and 3).

Figure 2

Figure 3

WARNING: To avoid possible fire or
electrical shock, make certain no
bare wire strands are exposed
outside wire connectors.

8.Carefully tuck all wires and splices into

the switch cup (Figure 2).

9. Connect the motor connector to the
switch cup connector.

10. Position the cup/light fitter on the
cover plate and install the three
screws that were previously removed
(Figure 1) and tighten securely.

11. Remove the wooden ball and pass
the fan switch chain through the
bushing in the fitter.

12. Proceed to “Installation of Glass
Globe” section.

To avoid possible fire or electric shock,
be careful not to pinch wires between
switch cup and the cover plate.

WARNING

To avoid possible fire hazard, do not
exceed wattage indicated on the
fixture.

WARNING

Installation on Emerson

Fans Having Two-Piece

Die-Cast Switch

Housings

3

MOTOR
CONNECTOR

SCREWS

SWITCH
CUP

CENTER SCREW

COVER PLATE

SWITCH CUP
CONNECTOR

MOTOR
CONNECTOR

BLACK WIRE

BLUE WIRE

HEX NUT

SCREWS

LOCKWASHER

SWITCH CUP

LIGHT
FIXTURE

COVER PLATE

SWITCH CUP
CONNECTOR

WIRE
CONNECTORS

WHITE WIRES

FAN SWITCH
CHAIN

THREADED
NIPPLE

CHAIN
BUSHING

SOCKET

GLOBE