Electrolux 57 Stainless Steel Gas Grill User Manual

57” Stainless Steel Gas Grill

Welcome & Congratulations

Please record Grill information for future reference and service work:

Model #:

Serial #:

Date of Purchase:

Gas Type:

Please retain this manual for future reference

Congratulations on your purchase of a new gas grill! At Electrolux Home Products, we are very proud of our product and are completely committed to providing you with the best service possible. Your satisfaction is our number one priority.

We know you’ll enjoy your new gas grill and Thank You for choosing our product. We hope you consider us for future purchases.

PLEASE CAREFULLY READ AND SAVE THESE INSTRUCTIONS

This Use & Care Manual provides specific operating instruction for your model. Use your gas grill only as instructed in this manual. These instructions are not meant to cover every possible condition and situation that may occur. Common sense and caution must be practiced when installing, operating and maintaining any appliance.

Questions? 1-800-320-0859

TABLE OF CONTENTS

Welcome/Product Registration..............................1

General Safety Instructions...................................2

Grill Features & Components................................3

Grill Assembly/Built-In Instructions........................4-8

Gas Requirements/Leak Testing...........................9-11

Using the Grill.......................................................12-15

Lighting the Grill....................................................13

Care & Cleaning....................................................16

Solutions to Common Problems............................17-18

Warranty.................................................................19

TESTED IN ACCORDANCE WITH ANSI Z21.58b-2002/CGA 1.6b-M02 STANDARD FOR OUTDOOR COOKING GAS APPLIANCES. THIS GRILL IS FOR OUTDOOR USE ONLY.

Check your local building codes for the proper method of installation. In the absence of local codes, this unit should be installed in accordance with the National Fuel Gas Code No. Z223.1-2002 and the National Electrical Code ANSI/NFPA No. 70-1990

WARNING

DO NOT try lighting this appliance without reading

the “LIGHTING INSTRUCTIONS” section of this manual.

FOR YOUR SAFETY

DO NOT store or use gasoline or other flammable vapors and

liquids in the vicinity of this or any other appliance.

An LP cylinder not connected for use shall not be stored

the vicinity of this or any other appliance.

General Safety Instructions

IMPORTANT SAFETY INFORMATION

- Read this manual carefully before using your grill to reduce the risk of fire, burn hazard or other injury.

- Extreme care should be used because of the high temperatures produced by this appliance.

CHILDREN SHOULD NOT BE LEFT UNATTENDED IN AN AREA WHERE THE GRILL IS BEING OPERATED.

- This appliance must be kept clear from combustible materials, gasoline or other flammable vapors

and liquids. Do not allow flammable materials to come in contact with grate, burner or hot surfaces.

- Do not repair or replace any part of this appliance unless it is specifically recommended in this

manual. A qualified service technician should conduct all other service.

- Follow the installation and servicing instructions provided with this product. Have your grill

installed by a qualified service technician. Locate the main gas supply valve so that you know how to shut the gas off to your grill. If you smell gas, make sure all gas connections are tight before operation. If you continue to smell gas call a qualified technician.

- When lighting a burner, always pay close attention to what you are doing. Be certain you are

pushing the ignitor that lights the burner you intend on using.

FOR YOUR SAFETY

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open flames.

3. Open lid.

4. If odor continues, immediately call your gas supplier.

FOR OUTDOOR USE ONLY

This appliance is not intended to be

installed in or on recreational vehicles or boats.

CALIFORNIA PROPOSITION 65 - WARN- ING: The Burning of gas cooking fuels generates some by products which are on the list of substances which are known by the State of California to cause cancer or reproductive harm. California law requires businesses to warn customers of potential exposure to such substances. To minimize exposure to these substances, always operate this unit according to the use and care manual, ensuring you provide good ventila-

tion when cooking with gas.

1. Roll top grill hood 8. Warming shelf

2. Grilling/Cooking surface 9. Infrared back burner

3. Side Shelf 10. Electronic ignitors: main, rear infrared & side burner

4. Control knob: back infrared burner 11. Cart w/doors

5. Control knobs: main burners 12. Drip Pans

6. Warming drawer 13. Side Burners

7. Handle 14. Control knobs:side burner

15. Control knob: bottom infrared burner

Grill Features: GL57

Ignitor Attachment

1. Remove the ignitor cap, spring assembly, battery and lock nut from ignitor. (See Fig. 1)

2. Insert the threaded section of the ignitor into the U-shaped cut out of the ignitor mounting bracket. (See Fig. 2)

3. Insert the threaded section of the ignitor through the hole in the shelf and secure to shelf using the lock nut. (Use the ignitor

assembly diagrams to determine which ignitor goes with which shelf.) Tighten

Securely. (See Fig. 3)

4. Re-insert the battery, positive side first, and spring assembly and attach the ignitor cap. (See Fig. 4)

5. Repeat above steps for second ignitor on the other shelf.

GL57 Ignitor

Assembly

Fig. 1

Fig. 2

Fig. 3

Fig. 4

Note: Prior to assembly remove protective film from stainless steel parts

Assembly requires: 4 tools and a Friend

Tools required:

1/4” socket wrench 1/2” socket wrench adjustable wrench scissors

Grill Assembly

Right Shelf (Double Wire)

Left Shelf (Four Wire)

Cap

Battery

Spring Assembly

Locking Nut

Cylinder

Mounting Bracket

Keyhole

Side Shelves Attachment

1. Loosen the bolts on the side of the grill and attach the shelf by allowing the bolt heads to fall through the large opening in the bottom of the keyhole slots. Then slide the shelves downward until the bolts are resting against the top of the key hole slots. Tighten all of the shelf bolts. (See Fig. 5)

2. Attach the wires coming out from the sides of the grill to the ignitor terminals. (See Fig. 6)

3. Repeat for second side shelf

Note: It does not matter which wire goes to which terminal on the four and two wire ignitor

Installing Side Burner

Plates:

1. There are 2 Black Circle Plates that need to be installed for the Side Burner to operate correctly.

2. Lift the Grate off of the Side Burner.

3. Place the Black Circle on top of the one Burner. (Repeat Step for second burner.) (See Fig. 7)

4. Replace Grate on top of the dual burners. (See Fig. 8)

Fig. 5

Fig. 6

Fig. 7

Fig. 8

Side Shelf/Side Burner Assembly

+ 14 hidden pages