Einhell GE-CH 1846 Li Kit(1x2Ah) - EX - NA Manual

EN Operating instructions

Cordless Hedge Trimmer

FR Mode d’emploi

Taille-haie sans fi l

SP Manual de instrucciones

Bordeadora de arbustos
inalámbrica

GE-CH 1846 Li

7

Art.-Nr.: 3410719 I.-Nr.: 21012

Anl_GC-CH_1846_Li_USA.indb 1Anl_GC-CH_1846_Li_USA.indb 1 13.12.2022 13:08:5013.12.2022 13:08:50

- 2 -

Anl_GC-CH_1846_Li_USA.indb 2Anl_GC-CH_1846_Li_USA.indb 2 13.12.2022 13:08:5313.12.2022 13:08:53

1

4

7

3

2 1

5

6

2

1

34

4

9 10

3

2

8

5

- 3 -

Anl_GC-CH_1846_Li_USA.indb 3Anl_GC-CH_1846_Li_USA.indb 3 13.12.2022 13:08:5313.12.2022 13:08:53

6 7

8

10

9

- 4 -

Anl_GC-CH_1846_Li_USA.indb 4Anl_GC-CH_1846_Li_USA.indb 4 13.12.2022 13:08:5713.12.2022 13:08:57

EN

DANGER!

When using the equipment, a number of safety
precautions must be observed to avoid injuries
and damage. Please read the complete operating
instructions and safety information with due care.
Keep these operating instructions in a safe place
so that the information is available at all times. If
you give the equipment to any other person, hand
over these operating instructions and the safety
information as well. We cannot accept any liability
for damage or accidents which arise due to
failure to follow these instructions and the safety
information.

1. Safety information

DANGER!
Read all the safety information and
instructions. Failure to adhere to the safety

information and instructions set out below
may result in electric shock, fi re and/or serious
injury. Keep all the safety information and

instructions in a safe place for future use.

General safety information for power tools

The term “power tool“ used in the safety
regulations refers to power tools operated from
the mains power supply (with a power cable) and
to battery operated power tools (without a power
cable).

1) Work area safety
a) Keep work area clean and well lit.

Cluttered and dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

fl ammable liquids, gases or dust. Power
tools create sparks which may ignite the dust
or fumes.

c) Keep children and bystanders away while

operating a power tool. Distractions can

cause you to lose control.

2) Electrical safety
a) Power tool plugs must match the outlet.

Never modify the plug in any way. Do
not use any adapter plugs with earthed
(grounded) power tools. Unmodifi ed plugs

and matching outlets will reduce risk of
electric shock.

b) Avoid body contact with earthed or

grounded surfaces such as pipes,
radiators, ranges and refrigerators. There

is an increased risk of electric shock if your
body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

d) Do not abuse the cord. Never use the

cord for carrying, pulling or unplugging
the power tool. Keep cord away from
heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the
risk of electric shock.

e) When operating a power tool outdoors,

use an extension cord suitable for
outdoor use. Use of a cord suitable for

outdoor use reduces the risk of electric
shock.

f) If operating a power tool in a damp

location is unavoidable, use a ground
fault circuit interruptor (GFCI) protected
supply. Use of an GFCI reduces the risk of

electric shock.

3) Personal safety
a) Stay alert, watch what you are doing and

use common sense when operating a
power tool. Do not use a power tool while
you are tired or under the infl uence of
drugs, alcohol or medication. A moment of

inattention while operating power tools may
result in serious personal injury.

b) Use personal protective equipment.

Always wear eye protection. Protective

equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce
personal injuries.

c) Prevent unintentional starting. Ensure

the switch is in the Off -position before
connecting to power source and/or
BATTERY pack, picking up or carrying the
tool. Carrying power tools with your fi nger on

the switch or energizing power tools that have
the switch on invites accidents.

d) Remove any adjusting key or wrench

before turning the power tool on. A wrench

or a key left attached to a rotating part of the
power tool may result in personal injury.

e) Do not overreach. Keep proper footing

and balance at all times. This enables

better control of the power tool in unexpected
situations.

f) Dress properly. Do not wear loose

clothing or jewellery. Keep your hair,
clothing and gloves away from moving
parts. Loose clothes, jewelery or long hair

- 5 -

Anl_GC-CH_1846_Li_USA.indb 5Anl_GC-CH_1846_Li_USA.indb 5 13.12.2022 13:08:5813.12.2022 13:08:58

EN

can be caught in moving parts.

g) If devices are provided for the connection

of dust extraction and collection facilities,
ensure these are connected and properly
used. Use of these devices can reduce dust

related hazards.

h) Do not let familiarity gained from frequent

use of tools allow you to become
complacent and ignore tool safety
principles. A careless action can cause

severe injury within a fraction of a second.

4) Power tool use and care
a) Do not force the power tool. Use the

correct power tool for your application.

The correct power tool will do the job
better and safer at the rate for which it was
designed.

b) Do not use the power tool if the switch

does not turn it on and off . Any power tool

that cannot be controlled with the switch is
dangerous and must be repaired.

c) Disconnect the plug from the power

source and/or remove the battery pack,
if detachable, from the power tool before
making any adjustments, changing
accessories, or storing power tools. Such

preventive safety measures reduce the risk of
starting the power tool accidentally.

d) Store idle power tools out of the reach

of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.

Power tools are dangerous in the hands of
untrained users.

e) Maintain power tools and accessories.

Check for misalignment or binding of
moving parts, breakage of parts and
any other condition that may aff ect the
power tool’s operation. If damaged, have
the power tool repaired before use. Many

accidents are caused by poorly maintained
power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.

g) Use the power tool, accessories and

tool bits etc., in accordance with
these instructions and in the manner
intended for the particular type of power
tool, taking into account the working
conditions and the work to be performed.

Use of the power tool for operations diff erent
from intended could result in a hazardous

situation.

h) Keep handles and grasping surfaces

dry, clean and free from oil and grease.

Slippery handles and grasping surfaces do
not allow for safe handling and control of the
tool in unexpected situations.

5) Battery tool use and care
a) Recharge only with the charger specifi ed

by the manufacturer. A charger that is

suitable for one type of battery pack may
create a risk of fi re when used with another
battery pack.

b) Use power tools only with specifi cally

designated battery packs. Use of any other

battery packs may create a risk of injury and
fi re.

c) When battery pack is not in use, keep it

away from other metal objects, like paper
clips, coins, keys, nails, screws or other
small metal objects that can make a
connection from one terminal to another.

Shorting the battery terminals together may
cause burns or a fi re.

d) Under abusive conditions, liquid may be

ejected from the battery; avoid contact.
If contact accidentally occurs, fl ush with
water. If liquid contacts eyes, additionally
seek medical help. Liquid ejected from the

battery may cause irritation or burns.

e) Do not use a BATTERY pack or tool that

is damaged or modifi ed. Damaged or

modifi ed batteries may exhibit unpredictable
behavior resulting in fi re, EXPLOSION or risk
of injury.

f) Do not expose a BATTERY pack or tool to

fi re or excessive temperature. Exposure to

fi re or temperature above 266°F (130°C) may
cause explosion.

g) Follow all charging instructions and do

not charge the BATTERY pack or tool
outside the temperature range specifi ed
in the instructions. Charging improperly or

at temperatures outside the specifi ed range
may damage the BATTERY and increase the
risk of fi re.

6) Service
a) Have your power tool serviced by a

qualifi ed repair person using only
identical replacement parts. This will

ensure that the safety of the power tool is
maintained.

b) Never service damaged BATTERY packs.

Service of BATTERY packs should only be

- 6 -

Anl_GC-CH_1846_Li_USA.indb 6Anl_GC-CH_1846_Li_USA.indb 6 13.12.2022 13:08:5813.12.2022 13:08:58

EN

performed by the manufacturer or authorized
service providers.

Additional safety instructions

We pay a great deal of attention to the design
of every battery pack to ensure that we supply
you with batteries which feature maximum
power density, durability and safety. The battery
cells have a wide range of safety devices.
Each individual cell is initially formatted and its
electrical characteristic curves are recorded.
These data are then used exclusively to be able
to assemble the best possible battery packs.

Despite all the safety precautions, caution
must always be exercised when handling
batteries. The following points must be
obeyed at all times to ensure safe use.
Safe use can only be guaranteed if
undamaged cells are used. Incorrect
handling can cause cell damage.

Caution! Analyses confi rm that incorrect use and

poor care are the main causes of the damage
caused by high performance batteries.

Information about the battery

1. The battery pack supplied with your cordless
tool is not charged. The battery pack has to
be charged before you use the tool for the fi rst
time.

2. For optimum battery performance avoid low
discharge cycles. Charge the battery pack
frequently.

3. Store the battery pack in a cool place, ideally
at 59°F (15°C) and charged to at least 40%.

4. Lithium-Ion batteries are subject to a natural
ageing process. The battery pack must be
replaced at the latest when its capacity
falls to just 80% of its capacity when new.
Weakened cells in an aged battery pack are
no longer capable of meeting the high power
requirements and therefore pose a safety risk.

5. Do not throw battery packs into an open fi re.
There is a risk of explosion!

6. Do not ignite the battery pack or expose it to
fi re.

7. Do not exhaustively discharge batteries.
Exhaustive discharge will damage the battery
cells. The most common cause of deep
discharge is lengthy storage or non-use of
partly discharged batteries. Stop working as
soon as the performance of the battery falls
noticeably or the electronic protection system
triggers. Place the battery pack in storage
only after it has been fully charged.

8. Protect batteries and the tool from
overloads. Overloads will quickly result
in overheating and cell damage inside the
battery housing without this overheating
actually being apparent externally.

9. Avoid damage and shocks. Replace
batteries which have been dropped from
a height of more than one meter or which
have been exposed to violent shocks without
delay, even if the housing of the battery pack
appears to be undamaged. The battery cells
inside the battery may have suff ered serious
damage. In this respect, please also read the
waste disposal information.

10. If the battery pack suff ers overloading and
overheating, the integrated protective cut­off will switch off the equipment for safety
reasons. Caution! Do not press the ON/OFF
switch any more if the protective cut-off has
actuated. This may damage the battery.

11. Use only original battery packs. The use
of other batteries may result in injuries,
explosion and a fi re risk.

12. Protect your rechargeable battery against
moisture, rain and high humidity. Moisture,
rain and high humidity can cause dangerous
cell damage. Never charge or work with
batteries which have been exposed to
moisture, rain or high humidity – replace them
immediately.

13. If your equipment is fi tted with a detachable
battery, remove the battery for safety reasons
after you have fi nished your work.

Information on chargers and the charging
process

1. Please check the data marked on the rating
plate of the battery charger. Be sure to
connect the battery charger to a power supply
with the voltage marked on the rating plate.
Never connect it to a diff erent mains voltage.

2. Protect the battery charger and its cable from
damage and sharp edges. Have damaged
cables repaired without delay by a qualifi ed
electrician.

3. Keep the battery charger, batteries and the
cordless tool out of children‘s reach.

4. Do not use damaged battery chargers.

5. Do not use the supplied battery charger to
charge other cordless tools.

6. In heavy use the battery pack will become
warm. Allow the battery pack to cool to room
temperature before commencing with the
charging.

7. Do not over-charge batteries. Do not

- 7 -

Anl_GC-CH_1846_Li_USA.indb 7Anl_GC-CH_1846_Li_USA.indb 7 13.12.2022 13:08:5813.12.2022 13:08:58

EN

exceed the maximum charging times. These
charging times apply only to discharged
batteries. Frequent insertion of a charged
or partly charged battery pack will result in
over-charging and cell damage. Do not leave
batteries in the charger for more than 48
hours.

8. Never use or charge batteries if you

suspect that the last time they were
charged was more than 12 months
previously. There is a high probability

that the battery pack has already suff ered
dangerous damage (exhaustive discharge).

9. Charging batteries at a temperature below
50°F (10°C) will cause chemical damage to
the cell and may cause a fi re.

10. Do not use batteries which have heated
during the charging process, as the battery
cells may have suff ered dangerous damage.

11. Do not use batteries which have suff ered
curvature or deformation during the charging
process or which show other non-typical
symptoms (gassing, hissing, cracking,…)

12. Never fully discharge the battery pack
(recommended depth of discharge max.
80%) A complete discharge of the battery
pack will lead to premature ageing of the
battery cells.

13. Never charge the batteries unsupervised.

Protection from environmental infl uences

1. Wear suitable work clothes. Wear safety
goggles.

2. Protect your cordless tool and the battery
charger from moisture and rain. Moisture
and rain can cause dangerous cell damage.

3. Do not use the cordless tool or the battery
charger near vapors and infl ammable liquids.

4. Use the battery charger and cordless tools
only in dry conditions and an ambient
temperature of 50°F to 104°F (10°C to 40°C).

5. Do not keep the battery charger in places
where the temperature is liable to reach over
104°F (40°C). In particular, do not leave the
battery charger in a car that is parked in the
sunshine.

6. Protect batteries from overheating.
Overloads, over-charging and exposure to
direct sunlight will result in overheating and
cell damage. Never charge or work with
batteries which have been overheated –
replace them immediately if possible.

7. Storage of batteries, battery chargers
and cordless tools. Store the charger and
your cordless tool only in dry places with an

ambient temperature of 50°F to 104°F (10°C
to 40°C). Store the Lithium-Ion rechargeable
battery in a cool and dry place at 50°F to 68°F
(10°C to 20°C). Protect them from humidity
and direct sunlight! Place only fully charged
batteries in storage (charged at least 40%).

8. Prevent the Lithium-Ion battery pack from
freezing. Battery packs which were stored
below 32°F (0°C) for more than 60 minutes
must be disposed of.

9. When handling batteries beware of
electrostatic charge: Electrostatic discharges
cause damage of the electronic protection
system and the battery cells. Avoid
electrostatic charging and never touch the
battery poles.

Battery Caution + Disposal

Disposal

Should your appliance need replacement after
extended use, do not dispose of it with the
household refuse, but in an environmentally safe
way.

Waste produced by electrical machine
items should not be handled like normal
household rubbish. Please recycle where
recycle facilities exist. Check with your local

authority or retailer for recycling advice.
Always dispose of your battery pack according
to federal, state, provincial and local regulations.
Contact a recycling agency in your area for recycling
locations.

 CAUTION! Even discharged battery packs

contain some energy. Before disposing, use
electrical tape to cover the terminals to prevent
the battery pack from shorting, which could cause
a fi re or explosion.

 WARNING! To reduce the risk of injury or

explosion, never burn or incinerate a battery
pack even if it is damaged, dead, or completely
discharged. When burned, toxic fumes and
materials are emitted into the surrounding
atmosphere.

1. Batteries vary according to device. Consult

your manual for specifi c information.

2. Install only new batteries of the same type in

your product (where applicable).

3. Failure to insert batteries in the correct

polarity, as indicated in the battery
compartment or manual, may shorten the life
of the batteries or cause batteries to leak.

4. Do not mix old and new batteries.

5. Do not mix Alkaline, Standard (Carbon-Zinc),

- 8 -

Anl_GC-CH_1846_Li_USA.indb 8Anl_GC-CH_1846_Li_USA.indb 8 13.12.2022 13:08:5813.12.2022 13:08:58

EN

or Rechargeable (Nickel Cadmium, Nickel
Metal Hydride, or Lithium-Ion) batteries.

6. Do not dispose of batteries in fi re.

7. Batteries should be recycled or disposed of
as per state, provincial and local guidelines.

When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.

Safety instructions for hedge trimmers
Hedge trimmer safety warnings:

When clearing jammed material or

•

servicing the unit, make sure all power
switches are off and the battery pack is
removed or disconnected. Unexpected

actuation of the hedge trimmer while clearing
jammed material or servicing may result in
serious personal injury.

Keep all power cords and cables away

•

from cutting area. Power cords or cables
may be hidden in hedges or bushes and can
be accidentally cut by the blade.

Keep all parts of the body away from the

•

cutter blade. Do not remove cut material
or hold material to be cut when blades
are moving. Make sure the switch is off
when clearing jammed material. Blades
coast after turn off. A moment of inattention

while operating the hedge trimmer may result
in serious personal injury.

Carry the hedge trimmer by the handle

•

with the cutter blade stopped. When
transporting or storing the hedge trimmer
always fit the cutting guard. Proper

handling of the hedge trimmer will reduce
possible personal injury from the cutter
blades.

Hold the power tool by insulated gripping

•

surfaces only, because the cutter blade
may contact hidden wiring or its own
cord. Cutter blades contacting a live wire

may make exposed metal parts of the power
tool live and could give the operator an
electric shock.
Keep hands away from blade. Contact with

•

blade will result in serious personal injury.

Always use head protection when

•

operating the hedge trimmer overhead.

Falling debris can result in serious personal
injury.

WARNING – Only use with handle and guard
properly assembled to hedge trimmer. The
use of the hedge trimmer without the proper

guard or handle provided may result in
serious personal injury.

Additional safety information

Before you start trimming hedges, check

•

the hedge for hidden objects, such as
wire fences.
Hold the hedge trimmer correctly with

•

both hands.
Always ensure that all handles and

•

guards are fitted before using the power
tool .
Do not attempt to use an incomplete

•

machine or one that is provided with an
unauthorized change.
Before cleaning the hedge trimmer, turn

•

off the tool and remove battery pack.
Check blades for damage regularly, if

•

damaged, repaired immediately.
Never allow children to use the power

•

tool.
Insert the blade to the blade cover, make

•

sure that the blade is not exposed after
use.
Do not use the tool in bad weather

•

conditions, especially during a
thunderstorm.

SAVE THESE INSTRUCTIONS

Explanation of the warning signs on the
machine (Figure 2)

1. Warning!

2. Do not expose the hedge trimmer to rain or
wet conditions!

3. Read the instructions for use before use!

4. Wear eye protection and ear plugs!

2. Layout and items supplied

2.1 Layout

1. Blades

2. Hand guard

3. Steady grip with button switch

4. Handle with button switch

5. Impact guard

6. Cutter guard

7. Battery

8. Push-lock button

9. Battery capacity indicator

10. Battery capacity indicator button

- 9 -

Anl_GC-CH_1846_Li_USA.indb 9Anl_GC-CH_1846_Li_USA.indb 9 13.12.2022 13:08:5813.12.2022 13:08:58

EN

2.2 Items supplied

Please check that the article is complete as
specifi ed in the scope of delivery. If parts are
missing, please contact our service center or the
store where you made your purchase at the latest
within 5 work days after purchasing the article and
upon presentation of a valid bill of purchase.

Open the packaging and take out the

•

equipment with care.
Remove the packaging material and any

•

packaging and/or transportation braces (if
present).
Check to see if all the items are supplied.

•

Inspect the equipment and accessories for

•

transport damage.
If possible, keep the packaging until the end

•

of the guarantee period.

Danger!
The equipment and packaging material are
not toys. Do not let children play with plastic
bags, plastic sheets and small parts. There is
a risk of choking and suff ocating!

Cordless Hedge Trimmer

•

Cutter guard

•

Original operating instruction with safety

•

information

Separately available accessories

18V 1.5Ah PXC Lithium-Ion battery
18V 2.0Ah PXC Lithium-Ion battery
18V 2.5Ah PXC Lithium-Ion battery
18V 3.0Ah PXC Lithium-Ion battery
18V 4.0Ah PXC Lithium-Ion battery
18V 3.0Ah PXC Plus Lithium-Ion battery
18V 4.0Ah PXC Plus Lithium-Ion battery
18V 5.2Ah PXC Plus Lithium-Ion battery
18V 4.0Ah/6.0Ah PXC Plus Lithium-Ion battery
18V 5.0Ah/8.0Ah PXC Plus Lithium-Ion battery
18V PXC Dual Port Fast Charger
18V PXC Fast Charger

Contact your local retailer for more specifi c
models of batteries and charger available in your
area. You can also explore battery + charger
options at Einhell.com.

The equipment is allowed to be used only for its
prescribed purpose. Any other use is deemed to
be a case of misuse. The user/operator and not
the manufacturer will be liable for any damage or
injuries of any kind resulting from such misuse.

Please note that our equipment has not been
designed for use in commercial, trade or
industrial applications. Our warranty will be voided
if the equipment is used in commercial, trade or
industrial businesses or for equivalent purposes.

4. Technical data

Motor power supply: ............................ 18V

Cutting speed: .............................. 2200 cuts/min

Blade length: .............................................. 20.5"

Max. cutting diameter: ................................ 0.43"

Weight (Tool only): .................................... 4.4 lbs

Reduce noise generation and vibration to a
minimum!

Use only equipment that is in perfect

•

condition.
Maintain and clean the equipment regularly.

•

Adapt your way of working to the equipment.

•

Do not overload the equipment.

•

Have the equipment checked if necessary.

•

Switch off the equipment when not in use.

•

Wear gloves.

•

5. Before starting the equipment

5.1 Installing the battery (Fig. 3)

Press the push-lock button of the battery as
shown in Fig. 3 and push the battery into the
mount provided. When the battery is positioned
as in Fig. 1, make sure that the push-lock button
latches in place! To remove the battery, proceed
in reverse order.

5.2 Charging the Lithium-Ion battery

The corresponding instructions can be found
in the original operating instructions for your
charger.

3. Intended use

This hedge trimmer is suitable for cutting hedges,
bushes and shrubs.

- 10 -

Anl_GC-CH_1846_Li_USA.indb 10Anl_GC-CH_1846_Li_USA.indb 10 13.12.2022 13:08:5813.12.2022 13:08:58

EN

5.3 Battery capacity indicator (Fig. 4)

Press the battery capacity indicator switch (10).
The battery capacity indicator (9) shows the
charge status of the battery using 3 LEDs.

All 3 LEDs lit:

The battery is fully charged.

2 or 1 LED(s) lit:

The battery has an adequate remaining charge.

1 LED fl ashing:

The battery is empty, recharge the battery.

All LEDs fl ashing:

The temperature of the battery is too low. Remove
the battery from the device and leave it at room
temperature for a day. If the error occurs again,
this means that the battery has been completely
depthdischarged and is defective. Remove the
battery from the device. Never use or charge a
defective battery.

6. Operation

Switching ON/OFF.

The hedge trimmer is equipped with a two­handed safety switch. The machine works only
when the switch on the steady grip (Figure 1 /
Item 3) is pressed with one hand and the switch
on the handle (Figure 1 / Item 4) is pressed with
the other hand. If either switch is released, the
cutters will stop moving. Please watch out for the
cutters as they slow down to a standstill.

Notes on working practice

A hedge trimmer can be used to cut shrubs

•

and bushes as well as hedges.
To obtain the best cutting results, hold the

•

hedge trimmer so that the cutter teeth are
at an angle of approx. 15° in relation to the
hedge (see Figure 5).
The twin-bladed cutters rotate in opposite

•

directions, thus enabling cutting in both
directions (see Figure 6).
It is recommended to tie a guide line of string

•

or the like along the hedge so that you cut the
hedge to a level height. Cut off all branches
which protrude beyond the guide line (see
Figure 7).
Cut the sides of the hedge with curve-shaped

•

movements from the bottom up (see Figure

8).

7. Cleaning and maintenance

HAZARD!

Always take the battery out of the equipment
before starting any cleaning work.

7.1 Cleaning

Keep all safety devices, air vents and the

•

motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it down with compressed air at
low pressure.
We recommend cleaning the equipment

•

immediately each time after use.
Clean the equipment regularly with a damp

•

cloth and some soft soap. Do not use
cleaning agents or solvents; these may
be aggressive to the plastic parts in the
equipment. Ensure that no water can get into
the interior of the equipment. The ingress of
water into an electric power tool increases the
risk of an electric shock.
Remove deposits from the cutter guard with

•

a brush.

7.2 Maintenance

The cutters should be cleaned and lubricated

•

at regular intervals in order to ensure best
performance at all times. Remove deposits
with a brush and apply a thin film of machine
oil (Figure 9).
There are no other parts inside the equipment

•

which require maintenance.
For storage, the hedge trimmer can be hung

•

up on a nail, screw or similar in a borehole
on the impact guard, without the cutter guard
mounted (Fig. 10).

8. Disposal and recycling

The equipment is supplied in packaging to
prevent it from being damaged in transit. The
raw materials in this packaging can be reused or
recycled. The equipment and its accessories are
made of various types of material, such as metal
and plastic. Never place defective equipment in
your household refuse. The equipment should
be taken to a suitable collection center for proper
disposal. If you do not know the whereabouts of
such a collection point, you should ask in your
local council offi ces.

- 11 -

Anl_GC-CH_1846_Li_USA.indb 11Anl_GC-CH_1846_Li_USA.indb 11 13.12.2022 13:08:5813.12.2022 13:08:58