Eaton Electrical 66103 User Manual

www.eaton.com

Network
Management
Card &
Modbus/
Jbus

(66103)

Installation manual

2 - 34003906EN/AE

The Network Management Card & Modbus/Jbus (66103) is recommended for central UPSs
protecting entire networks or for UPS units backing up critical loads. With the card installed, the UPS
has its own IP address and uses the local computer capabilities to:

● Supply web pages (http or https (SSL)) with information on status conditions and measurements/

settings/alarms,

● Integrate an SNMP-based NMS such as HP OpenView, IBM Tivoli Netview and Computer Associates

Unicenter,

● Communicate with shutdown modules installed on the protected servers (Network Shutdown

Module),

● Send e-mail and SMS messages,

● Control the ON/OFF function of the UPS and the outlets,

● Monitor the Environment Sensor (optional, cat. no. 66846).

UNPACKING AND CHECKS

● One Network Management Card & Modbus/Jbus (66103)

● One serial cable for configuration (34003918),

● One installation manual (34003906).

CHECK ON UPS VERSION

Pulsar

The Network Management Card & Modbus/Jbus (66103) is compatible with the
available since 2006.Note.

Important. Before installing the card, check that the UPS technical level (NT) is at least
equal to that indicated in the table below.

UPS Type Technical level (NT)

Pulsar 700/1000/1500 02

Pulsar M 2200/3000 03

Pulsar MX 4000/5000/10000 04

Pulsar MX Frame 15/20 kVA 01

● If the technical level of the UPS is lower than that indicated in the table, contact EATON.

range UPSs

34003906EN/AE - 3

.

Settings/Sensor

6

6

1

0

3

U

P

S

data R

S

232

1

00M

10

M

000623001C07

ETHERNET 10/100BT port
Service port (Settings/Sensor)

Orange LED: RS232 activity

Green LED: communication
with the UPS

Catalogue number

Orange LED: 10/100M
Green LED: connection +

activity

MAC address

Jbus/modbus port

OVERVIEW

INDICATIONS

ETHERNET port

LED Colour Status Description

ACT Green ● OFF

●

ON

●

Flashing

100M Orange ●

●

OFF
ON

Service port (Settings/Sensor)

Card not connected to network

●

●

Card connected to network, but no activity

●

Port is sending/receiving

Port operating at 10 Mbits/s

●

●

Port operating at 100 Mbits/s

LED Colour Status Description

UPS Data Green ● OFF

●

ON

●

Flashing

RS232 Orange ●

OFF

●

ON

●

Flashing

Card starting

●

●

Communicating with UPS

●

Normal operation

Communication with UPS is operational

Configuration menu activated

●

●

Normal operation

Configuration menu not activated

●

Communication with Environment Sensor (option)

4 - 34003906EN/AE

The Network Management Card & Modbus/Jbus (66103) can be hot-plugged on all UPSs from

ETHERNET

ASI

S
e

t
t

i
n

g

s
/

S

e
n

s
o

r

6

6
1

0

3

U

P
S

d
a
t

a

R
S

2
3
2

1
0
0

M

1

0
M

EATON equipped with a Minislot. It is not necessary to shutdown the UPS, disconnect the load or restart
the UPS.

● Remove the plastic cover of the Minislot.

● Note the MAC address of the card before inserting it.

● Insert and secure the card with the screws.

● Connect the ETHERNET cable.

● Check the ETHERNET port indications.

● Wait until the UPS Data LED flashes regularly (approx. two minutes), indicating that card start-up has

terminated correctly.

Note. Connection detection continues until the card has been connected to the network. Once
connection is made, card start-up continues.

IP SETTINGS

Once the card has started, proceed as indicated below.

● Connect the serial cable to card’s service port and PC’s COM port

● Use a terminal emulator such as HyperTerminal

TM

with these settings

Bits per second Data bits Stop bits Parity Flow control
9600 8 1 none none

"Echo typed characters locally" option: disabled

● Type EATON (or eaton).

The main configuration menu is displayed:

EATON
NETWORK MANAGEMENT CARD

1 : Reset
2 : Network configuration
3 : Set Login Password to Default
4 : Return to Default Configuration
5 : Jbus configuration
6 : Sensor configuration
0 : Exit

34003906EN/AE - 5

Your network is equipped with a BOOTP/DHCP server (default)

The card is configured by default with this service enabled. No manual configuration is required.The IP
parameters are automatically collected by the card.

From the main configuration menu: (see above)

● Press the 2 key (Network configuration).

● Press the 1 key(Read Network settings).

The settings supplied by the server are displayed:

Network configuration :

MAC address : 00:06:23:00:1C:07
Mode : DHCP
IP address : 172.17.23.18
Subnet mask : 255.255.248.0
Gateway : 172.17.17

● Note the IP address.

● Press the 0 key (Exit).

● Press the 0 key (Exit).

You can also use NMC Tool software utility to view the card IP adress
Provided on the Solution-Pac 2 CD-ROM or at www.eaton.com. It must be installed on a network
connected PC.

Your network is not equipped with a BOOTP/DHCP server

Manual configuration is required.

To set the network configuration, use terminal emulation (see above)
From the main configuration menu:

● Press the 2 key (Network configuration).

● Press the 2 key (Modify Network settings).

● Follow the instructions and enter the IP parameters:

1 : Read Network settings
2 : Modify Network settings
3 : Set ethernet speed

0 : Exit
For each of the following questions, you can press "Return" to
select
the value shown in braces, or you can enter a new value
Should this target obtain IP settings from the network?[N] N
Static IP address [172.17.16.16]?172.16.1.82
Subnet mask IP address [255.255.0.0]? 255.255.255.0
Gateway address IP address [0.0.0.0]? 172.17.17.1
Done

Wait until "Done" is displayed, indicating that the IP parameters have been saved.

● Press the 0 key (Exit).

● Press the 1 key (Reset).

● Press the 2 key (Restart).

The card restarts with the new IP settings (after approx. one minute).

6 - 34003906EN/AE

ACCESS TO SUPERVISION

To check whether the
installation and configuration, proceed as follows.

● Run a browser

● Enter in the address bar:

http://IP address/ (e.g. http://172.16.1.82/)

● The home page is displayed

Network Management Card

& Modbus/Jbus (66103)

is operational after

● Set the time by clicking the Time command.

● Continue configuration via the sections in the Settings menu.

USER MANUAL

This manual provides all the information required to install and configure the

Card

& Modbus/Jbus

For more information on the supervision, control and configuration functions offered by the

Management Card

in the Products/Power Management section of the

(66103).

& Modbus/Jbus

(66103), see the user manual on the

www.eaton.com/powerquality

Network Management

Solution-Pac 2

site.

34003906EN/AE - 7

Network

CD-ROM or

6

6

1

0

2

S

e

ttin

g

s

/S

e

n

s

o

r

E

T

H

E

R

N

E

T

1
0

0
M

1
0

M

U

P

S

d
a
t

a

R

S
2

3
2

O

n

=

L
i

n
k

B

l
i
n

k

=

A
c

t

ETHERNET

6

6

1

0

3

U

P

S d

a
ta R

S
23

2

10

0

M

10

M

SENSOR CONNECTION (option)

The Environment sensor is a Network Management Card & Modbus/Jbus option. It is available
from EATON (cat. no 66846).
The sensor remotely monitors the UPS environment by regularly measuring the temperature and
humidity, and checking the states of two external contacts. It can also send alarms (e-mail, SNMP trap)
tripped by pre-set thresholds.
Connection is made via the Service port (Settings/Sensor) on the Network Management Card &
Modbus/Jbus. The sensor is detected automatically. Configuration and supervision use a menu that
may be accessed directly from the home page. For more information, see the user manual of the
Network Management Card & Modbus/Jbus.

8 - 34003906EN/AE

JBUS/MODBUS

5

Txd RxdSG

43 2 1

SA1

SA2

SA2

Pin Function

1 Received data (input)
2 Not connected
3 Transmitted data (output)
4 Not connected
5 Signal ground

SA2

OFF

ON

1

8

RD = (A')

TD = (B)

TD = (A)

0 V

1

2

3

4

5

RS485

RD = (B')

R-

R+

T-

T+

0 V

SA1

SA2

SA1

OFF

ON

1

8

SA2

OFF

ON

1

8

SA2

SA2

SA2

SA1

SA1

SA1

RS232 link configuration and connection

RS485 link configuration and connection

For proper operation, the polarity of EIA RS485 2-wire and 4-wire lines must be set at only one point
and the lines terminated at the end.

Polarity

Normally, the master of the network sets the polarity of the line. The receiver inputs have a true failsafe
feature wich eliminates the need for external bias resistors and ensures a logic high output level when
the inputs are open or shorted. This guarantees that the receiver outputs are in a known state before
communication begins and when communication ceases.

Termination

Termination is used to match impedance of a node to the impedance of the transmission line being
used. When impedance are mismatched, the transmitted signal is not completely absorbed by the load
and a portion is reflected back into the transmission line. The termination line is not necessary if the
speed on the line is much less than 115Kbauds

The default setting of the RS485 is a 4 wires configuration without polarity and without termination.
SA1 switches are used to make the termination and the topology of the line (2 or 4 wires). The
termination resistance value is 166 Ω.

SA1 description:

1 : reserved
2 : reserved
3 : link termination between T- to R- (2 wires configuration) if set to ON
4 : connection T- to R- (2 wires configuration ) if set to ON
5 : connection T+ to R+ (2 wires configuration ) if set to ON
6 : reserved
7 : reserved
8 : link termination between R+ and R- if set to ON

34003906EN/AE - 9

2 wires connection

SA1

SA2

SA1

OFF

ON

1

8

SA2

OFF

ON

1

8

SA2

SA2

SA2

SA1

SA1

SA1

5

L +

43 2 1

L -

5V

Rp

Ra

Rp

0V

Ra

0V

Ra

0V

L- L-

L+ L+

L- L-

L+ L+

3

7

24

13

24

13

polarity

connection
if end
of the line

polarity

transmit/receive
data

transmit/receive
data

transmit/receive
data

termination

termination

Master unit Card of an end-of-line cubicle

connection
if end
of the line

3V3

SA1-3

3V3

SA1-3

Card of an intermediate cubicle

SA2

OFF

ON

8 7 6 5 4 3 2 1

SA1

SA1

OFF

ON

8 7 6 5 4 3 2 1

SA1

Link without polarity and without termination.

SA2

OFF

ON

8 7 6 5 4 3 2 1

SA1

SA1

OFF

ON

8 7 6 5 4 3 2 1

SA1

Link with termination.

Card settings of an intermediate cubicle

Others settings

10 - 34003906EN/AE

4 wires connection

SA1

SA2

5R-43 2 1

R +T -T +

SA1

OFF

ON

1

8

SA2

OFF

ON

1

8

SA2

SA2

SA2

SA1

SA1

SA1

5V

Rp

Rp

0V

Ra Ra

T- R-

T+ R+

R- R-

R+ R+

2

1

2

1

5V

Rp

Ra

Rp

0V

R- T-

R+ T+

T- T-

T+ T+

4

3

4

3

master
transmitt

slave
receiver

slave
receiver

termination

termination

receive data

slave
transmitt

receive data

slave
transmitt

transmit datatransmit data

transmit data

slave
receiver

receive data

polarity

connection if
end of the line

polarity

connection if
end of the line

Master unit Card of an intermediate cubicle Card of an end-of-line cubicle

SA2

OFF

ON

8 7 6 5 4 3 2 1

SA1

SA1

OFF

ON

8 7 6 5 4 3 2 1

SA1

Link without polarity and without termination.

SA2

OFF

ON

8 7 6 5 4 3 2 1

SA1

SA1

OFF

ON

8 7 6 5 4 3 2 1

SA1

Link with termination.

Card settings of an intermediate cubicle

Others settings

34003906EN/AE - 11

Configuration of the JBUS/MODBUS communication parameters

6

6

1

0

2

Settings/Sensor

ETHERNET

1
0

0
M

1
0

M

U
P

S
d
a

t
a

R
S

2

3
2

O

n
=

L
i
n

k

B

l
i
n
k

=

A
c

t

ETHERNET

6

6

1

0

3

UP

S
data

R
S2

32

1
00M

1

0

M

Connect the RS232 link to a

terminal

(Microsoft Hyper terminal)

Through settings port

● Use the cord supplied with the card

● Connect the card to a computer

● Use a terminal emulator such as HyperTerminal

TM

with these settings

Bits per second Data bits Stop bits Parity Flow control
9600 8 1 none none

"Echo typed characters locally" option: disabled

● Check that UPS power is on.

● Type EATON (or eaton).

The main configuration menu is displayed:

EATON
NETWORK MANAGEMENT CARD

1 : Reset
2 : Network configuration
3 : Set Login Password to Default
4 : Return to Default Configuration
5 : Jbus configuration
6 : Sensor configuration
0 : Exit

● Press the 5 key (Jbus configuration).

The Jbus configuration menu is displayed:

Jbus settings

1 : Display Jbus settings
2 : Modify Jbus settings
3 : Display Jbus diagnostics
4 : Reset Jbus diagnostics
5 : Return to Jbus Default Configuration
6 : Display Jbus frames
0 : Exit

12 - 34003906EN/AE

● Press the 2 key (Modifiy Jbus settings)

● Press «Return» key to modify the Jbus settings

Setting Jbus configutration

Set Slave number : 0x1*
Set the Baud Rate [1:38400,2: 19200, 3:9600, 4: 4800, 5: 2400,
6: 1200] :3
Set data format[1: 8 bits, 2: 7 bits] :1
Set stop bit[1: 1 bits, 2: 2 bits] :1
Set parity [1: None, 2: Even, 3: Odd] :1

Wait during the new setting is saved ...
TLS/Slave JBUS initialized
The Jbus configuration is now updated.

* Hex format.

Press the 0 key (Exit).

●

● Press the 0 key (Exit).

Through a web browser

● Run a browser

● Enter in the address bar:

http://IP address/ (e.g. http://172.16.1.82/)

● The home page is displayed

● Select the setting menu

● Set the parameters.

● Select the «Save» button to save the new parameters.

34003906EN/AE - 13

TECHNICAL CHARACTERISTICS

Physical characteristics

Dimensions (W x D x H) 132 x 66 x 42 mm

Weight 70 g

RoHS 100% compatible

Storage

Storage temperature range -10°C to 70°C

Ambient conditions

Operating temperature range 0°C to 40°C

Relative humidity 90% RH max. without condensation

Card performance

Supply voltage 5V ±5%

Supply current (all LEDs ON and
Environment Sensor connected)

Functions

Web supervision 5 browsers max. (http),

Languages English, French, German, Italian, Spanish

Alarms E-mail, SNMP TRAP, Web page

Log 400 measurements or events

Server protection Up to 100 servers protected

Network Fast ETHERNET, 10/100 Mbits, auto-negotiation

Identification User name and password

Security SSL 3.0, TLS 1.0

Browsers Microsoft Internet Explorer 6.x or higher

NMS Enterprise Power Manager (EPM)

MIB MIB II standard - UPS EATON MIB V1.7

Settings (default values)

IP network BOOTP/DHCP enabled

Web-page access control User name: EATON

Service-port menu access control Password: EATON or eaton (not modifiable)

Date and time Synchronise with an NTP server (GMT)

Service port 9600 bits/s, 8 bits, 1 bit stop, no parity

RS485 port Slave nb:0x01, 9600 bits/s, 8 bits, 1 bit stop, no parity

300 mA max.

3 browsers max. (https)

HTTP 1.1, SNMP V1, NTP, TFTP, SMTP, BOOTP/DHCP

Management-Pac 2

IP address: 172.17.16.16 (manual configuration)
Subnet mask: 255.255.0.0
Gateway: 0.0.0.0
NTP server: pool.ntp.org

Password: EATON

14 - 34003906EN/AE

ELECTROMAGNETIC COMPATIBILITY

When correctly installed and used in accordance with manufacturer instructions, the card complies with
the following standards:

● ITE (Information Technology Equipment) safety: IEC/EN 60950-1 2002

● EMC: EN 61000-6-2 (2002), EN 61000-6-3 (2002), IEC/EN 62040-2 (2002)

In compliance with European directives:

● Low voltage: 73/23/EEC and 93/68/EEC.

● EMC: 89/336/EEC and 93/68/EEC.

Federal Communication Commission (FCC) statement

This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment.

WEB SITE

The information presented in this manual is also available in other languages in the download section
of the EATON site (www.eaton.com/powerquality)

.

34003906EN/AE - 15

www.eaton.com

34003906EN/AE