Engineering Data Sheet |
IPX10:8 DSP power amplifier 8x1250W, install
▪ 8 x 1250 W multichannel installation DSP amplifier with digitally controlled PFC supply
▪ Fully integrated DSP with native 96 kHz and FIR Drive technology
▪ Dante and OCA integration via OMNEO with fallback options
▪ Parallel, Bridge and Parallel-bridge modes with 70/100/140/200 V and low impedance operation
▪ High efficiency Eco Rail technology for lower operating costs
Parts included
Quantity |
Component |
|
|
|
|
|
|
|
|
1 |
IPX series DSP power amplifier |
|
|
|
|
|
|||
2 |
8-pin Euroblock-type connector, Output, 6 mm |
|||
|
|
|
||
4 |
6-pin Euroblock-type connector, Input |
|
||
|
|
|
||
1 |
8-pin Euroblock-type connector, GPIO |
|
||
|
|
|
|
|
4 |
M6x20 screw for rack mounting |
|
|
|
|
|
|
|
|
1 |
Installation manual |
|
|
|
|
|
|||
1 |
Mains power connector, 32 A with safety & assem- |
|||
|
bly instruction |
|
|
|
|
|
|
|
|
1 |
Safety instruction booklet |
|
|
|
|
|
|
||
Technical specifications |
|
|
||
|
|
|
|
|
OUTPUT POWER |
|
|
|
|
|
|
|
|
|
Low-Z mode: Load |
2 Ω |
2.7 Ω |
4 Ω |
8 Ω |
Impedance |
|
|
|
|
Maximum Output
Power1
Normal Mode, all |
1300 W |
1500 W |
1250 W |
1250 W |
channels driven |
|
|
|
|
|
|
|
|
|
Bridge |
- |
- |
2600 W |
2500 W |
|
|
|
|
|
Parallel |
2500 W |
3000 W |
2500 W |
1250 W |
|
|
|
|
|
Parallel-Bridge |
5200 W |
6000 W |
5000 W |
5000 W |
|
|
|
|
|
Direct Drive Mode: |
70 V |
100 V |
140 V2 |
200 V2 |
Nominal Voltage |
|
|
|
|
|
|
|
|
|
Maximum Output |
1250 W |
1250 W |
2500 W |
2500 W |
Power1 |
|
|
|
|
Number of Amplifi- |
|
|
8 |
|
er Channels |
|
|
|
|
|
|
|
|
|
Maximum Output |
|
150 Vpeak |
|
|
Voltage, Normal |
|
|
|
|
mode, per channel |
|
|
|
|
|
|
|
|
|
Maximum Output |
|
41 Apeak |
|
|
Current, Normal mode, per channel
AMPLIFIER
Voltage Gain
2 | IPX10:8 DSP power amplifier 8x1250W, install
Low-Z mode, ref.1 |
32.0 dB, adjustable 20.0-44.0 dB |
kHz |
|
|
|
Direct Drive mode |
33.2/36.2/39.2/42.2 dB for |
|
70/100/140/200 V |
|
|
Input Sensitivity |
|
|
|
Low-Z mode, Max. |
10.7 dBu (2.66 V), adjustable -1.3-22.7 dBu |
Output Voltage |
|
|
|
Direct Drive mode |
6 dBu (1.55 V), fixed |
|
|
THD |
< 0.05 % |
3 dB below max, |
|
AES17, 1 kHz |
|
|
|
DIM 100 |
< 0.15 % |
3.15 kHz, 15 kHz |
|
|
|
IMD-SMPTE |
< 0.05 % |
60 Hz, 7 kHz |
|
|
|
Crosstalk |
< -80 dB |
ref. 1 kHz, 12 dB |
|
below Max, 8 Ω |
|
|
|
Frequency Re- |
20 Hz to 20 kHz (±0.5 dB) |
sponse |
|
ref. 1 kHz, analog in |
|
to speaker out |
|
|
|
Damping Factor |
> 400 |
20 Hz to 200 Hz, 8 |
|
Ω |
|
|
|
Output Stage Top- |
Class D, fixed frequency |
ology |
|
|
|
Signal to Noise Ra- |
|
tio Amplifier |
|
|
|
A-weighted, analog |
112 dB |
input |
|
|
|
A-weighted, digital |
115 dB |
input |
|
|
|
Output Noise |
|
|
|
A-weighted, analog |
< -70 dBu |
input |
|
|
|
A-weighted, digital |
< -73 dBu |
input |
|
|
|
CONNECTIVITY |
|
|
|
Analog Audio In- |
|
put/Thru |
|
|
|
Type |
4 x 6-pin Euroblock, male |
|
|
Maximum Input Lev- |
+21 dBu |
el |
|
|
|
Input Impedance, |
20 kΩ |
active balanced |
|
|
|
Reference level |
+21 dBu for 0 dBFS |
equal to digital in- |
|
put |
|
|
|
Speaker Output |
2 x 8-pin Euroblock, 6 mm, female |
|
|
GENERAL |
|
|
|
Power Consump- |
|
tion |
|
|
|
Rated power con- |
1300 W |
sumption (see BTU |
|
table) |
|
|
|
1/8 Maximum Out- |
1780 W |
put Power at 4 Ω |
|
|
|
Idle Mode (no input |
105 W |
signal) |
|
|
|
Standby Mode |
< 18 W |
|
|
Dimensions |
483 x 88.1 x 514.2 |
(W x H x D), mm |
|
|
|
Weight |
16.8 kg (37.1 lb) |
|
|
Shipping Weight |
19.1 kg (42.1 lb) |
|
|
|
|
DIGITAL SIGNAL PROCESSING |
|
|
|
Sampling rate |
48 kHz/96 kHz, OMNEO/Dante synchronized |
|
|
Signal delay/laten- |
0.70 ms/0.53 ms |
cy |
|
Analog In to Speak- |
|
er Out, 48 kHz/96 |
|
kHz |
|
|
|
Dante Network La- |
typ. 1.00 ms |
tency |
|
|
|
Signal Processing |
|
|
|
User EQ |
12 filters per channel, selectable as PEQ, Lo- |
|
Shelv, Hi-Shelv, Lo-ShelvQ, Hi-ShelvQ, Hi-Pass, |
|
Lo-Pass and Notch; 2 filters of them with addi- |
|
tional asymmetric filter type |
|
|
User Delay |
0 to 2000 ms per channel (units: µs, ms, s, cm, |
|
m, inches, feet) |
|
|
Array EQ |
5 filters per channel, selectable as PEQ, Lo- |
|
Shelv, Hi-Shelv, Lo-ShelvQ, Hi-ShelvQ, Hi-Pass, |
|
Lo-Pass, and All-Pass |
|
|
Array Delay |
0 to 500 ms per channel (units: µs, ms, s, cm, |
|
m, inches, feet) |
|
|
Speaker EQ |
10 filters per channel, selectable as PEQ, Lo- |
|
Shelv, Hi-Shelv, Hi-Pass, Lo-Pass and All-Pass |
|
|
Speaker X-Over |
Hi-Pass, and Lo-Pass per channel, |
|
6/12/18/24/30/36/42/48 dB Bessel/Butter- |
|
worth, 12/24/48 dB Linkwitz-Riley; Alignment |
|
Delay, 0 to 20 ms per channel |
|
|
Loading...