Doro PHONE EASY 311C User Manual
PhoneEasy 311C
English
1 One Touch (Direct)
Memories
2 Store/Mute button
and indicator light
3 Memory button
4 Recall button
5 Redial button
6 Earpiece Volume control
7 Visual Ring indicator
8 Handset hanger hook
Français
1 Touches des
mémoires directes
2 Touche Enregistrement /
Secret et témoin lumineux
3 Touche de mémoire abrégée
4 Touche R
Nederlands
1 Geheugentoetsen
2 Opslaan/Geluid
uitschakelen en LED
3 Geheugen
4 Doorverbinden
5 Touche Bis
6 Touches de réglage
du volume d’écoute
7 Indicateur de sonnerie
8 Languette de support
du combiné
5 Opnieuw kiezen
6 Volumeregeling hoorn
7 Belindicator
8 Ophanghaak voor
wandmontage
English
This device is intended for the analogue telephone network lines in AT,
BE, BG, CH, CY, CZ, DE, DK, EE, ES, FI, FR, GB, GR, HU, IE, IS,
IT, LV, LT, LU, MT, NL, NO, PL, PT, RO, SI, SK, SE.
Connection
1. Connect the handset curly cord to the handset and the socket on the
left-hand side of the telephone.
2. Connect the telephone line cord to the socket at the rear of the
telephone, and to a telephone network wall socket.
3. You will hear a click when the modular plug is correctly in place.
4. Lift the handset and listen for the dial tone. Your telephone is now
operational.
Wall mounting
The telephone can be wall mounted using two screws positioned
vertically at a distance of 100 mm, the screws should t into the ‘keyholes’
on the back of the telephone. Remove the hanger hook (please refer to
diagram on page 2) by pushing it upwards, then rotate it 180 degrees and
replace it.
Hearing Aid compatible
This telephone is hearing aid compatible. Select the T mode on your
hearing aid to enable this feature.
Mute button
Press and release z to mute the handset microphone during a call, the
light next to the button will ash while the microphone is muted. Press
and release z again to continue with your telephone conversation.
Redial button
If the number dialled is engaged or you wish to dial the last number
called lift the handset and press and release r. Redial will not work if
the number dialled was from memory (i.e. M1, M2, M3 or 0-9).
Memory
The telephone has 3 one-touch and 10 two-touch memories. One-touch
memories are stored in M1, M2 & M3, two touch memories are stored
using the telephone keypad digits 0-9.
1
English
Storing One-touch Memories
1. Lift the handset, press and release P (ignore anything you hear in the
earpiece).
2. Select a memory location M1, M2 or M3 by pressing the corresponding
button.
3. Enter the telephone number to be stored (up to 21 digits).
4. Press and release P again.
5. Replace the handset. The number is now stored.
Dialling using One-touch Memories
1. Lift the handset and wait for a dialling tone.
2. Select a memory location by pressing the corresponding memory
button (M1, M2 or M3). The stored number will now be dialled.
Storing Two-touch Memories
1. Lift the handset, press and release P (ignore anything you hear in the
earpiece).
2. Press and release
m
.
3. Select a memory location by pressing one of the keypad number
buttons 0-9.
4. Enter the telephone number to be stored (up to 21 digits).
5. Press and release P again.
6. Replace the handset. The number is now stored.
Dialling using Two-touch Memories
1. Lift the handset and wait for a dialling tone.
2. Press and release
m
.
3. Select a memory location by pressing the relevant keypad number
0-9
. The stored number will now be dialled.
Press and release r if you need to insert a pause in a telephone number. If a stored
number changes, follow the procedures above entering the new number in the same location
as the old one.
Earpiece Volume control
During a conversation press and release either v to increase or V to
decrease the earpiece volume.
2
Loading...