DoorKing 2361-080 Quick Start Manual

Wireless

Baseboard

DoorKing Part Number

WIRELESS BASEBOARD KIT

2361-080

This wireless baseboard kit provides wireless communication from the access control system to a wireless tracker expansion
board(s). Use this kit ONLY on DoorKing: 1833, 1835, 1837 and 1838 multi-door access controller access control systems.

Installation

The wireless baseboard REPLACES the 14-pin auxiliary terminal on the access control system’s board. The existing 16.5 VAC, 20 VA access control
system’s input power transformer is REQUIRED and is rewired to the 10-pin terminal #1-#2. Antenna is REQUIRED, see below for antenna options.

RS 232

DoorKing Access Control System Board

8

9

7

A

RF RANGECH

B

C

D

E

F

A

NET

B

C

ID

D

E

F

SYNC LOST

SYNC REVD

HEARTBEAT

Wireless

Wireless

4-Pin Terminal

RF
STAT STRENGTH

NO

NC

Relay 2 Jumper

FEED
BACK

321

6

5

RESET

4

3

2

1

0

PAIRED

8

9

7

6

5

ON

MIC
VOL

321

321

SPK
VOL

CLK
SEN

ON

MASTER
CODE

1833, 1835 and 1837 ONLY

RING

Relay 0

4

3

2

1

0

OFF

RCVD

ALLOW

DISPLAY
OFF/ON

DENY

STATU S

Baseboard

Baseboard

NO

NC C

Main Terminal

COMMICPSWCGNDPHONE

5VDCIMDSPKR

Cabinet Mounted
Dome Antenna Included

(Vandal-resistant) The range is
approximately 100 ft direct-line-of-sight.
Install on top of the cabinet in the
existing antenna mounting hole (remove
plug).

ELEVATOR

1

2

3

DOORKING

2363-010

14
13

10-Pin Terminal

12
11

6
5
4

DOORKING

2361-010

3
2
1

12345 67891011121314

14-Pin Auxiliary

Power
Transformer

Terminal
Connection

16AC16ACBAT1NO1NC1C2RY2CAZIMC

Range testing is HIGHLY recommended

Important Antenna Note: Antenna range WILL

VARY GREATLY depending on individual setup

(Antenna height above the ground, background
signal interference, physical obstructions
(trees, buildings etc.) and what antenna
you choose). Adverse weather (rain)
CAN also affect antenna range.

Externally Mounted

Longer Range

Adjustable

Antenna Included

13 ft of cable

Range is approximately 500 ft
direct-line-of-sight. Install antenna
vertically as high as possible in free
air above access control system.

before FINAL installation.

4-Pin Terminal:

Must connect to access control
system’s Relay 2 for wireless
tracker expansion board
addresses 3-10.

Must connect to access control
system’s Relay 1 for wireless
tracker expansion board
addresses 11-18.

Note: Terminals
can be removed

Relay 2 (2C) Com

Relay 2 (2RY)

Relay 1 (1C) Com

Relay 1 (1NO)

for NO.

Set relay 2

jumper

from board for
easy wiring.

18 AWG 100 ft max
16 AWG 200 ft max

16.5 VAC

Main

Door/Gate

Relay 1Relay 2

Wireless Tracker Board Addresses 3-10

Wireless Tracker Board Addresses 11-18

10-Pin Terminal: One 26-Bit wiegand access control device

(card reader) or up to 8 tracker expansion board addresses 11-18 (NOT
wireless) may be HARD wired to the 10-pin terminal (#11-12-13-14) for
Gate/Door control if desired (DO NOT connect HARDwired tracker
expansion boards or card reader to wiegand 1 (terminals 11-14) if
WIRELESS boards will be using wiegand 1). The wiegand 1 input will
activate whatever is wired to the access control system’s Relay 1 for the
access control system’s programmed strike time.

Optional - Wiegand 1 HARDWIRE input:
activates Relay 1 for the access control
system’s programmed strike time.

Note: NOT available when using wireless
tracker expansion board addresses 11-18.

Optional - Additional power for card readers
that use lighting for outdoor use.

Optional - maintains ONLY wiegand
operation during power outage.

REQUIRED

20 VA

Wire polarity

does not matter

+12 VDC Power

14)

Common

13)

DATA 1

12)

DATA 0

11)

16 VAC Output

6)

16 VAC Output

5)

Back-up Battery-NEG

4)

Back-up Battery-POS

3)

16.5 VAC Input Power – 20 VA

2)

16.5 VAC Input Power – 20 VA

1)

(Powers RS-232, elevator control, wiegand and wireless baseboard)

Other Antenna Options

Cabinet Mounted
Longer Range
Fixed Antenna Kit

Sold separately
Kit P/N: 1514-008

Range is approximately
200 ft direct-line-of-sight.

Install on top of the cabinet.

NOT vandal-resistant.

Wireless Repeater

Sold separately P/N 2364-080
The range is approximately
500 ft direct-line-of-sight with
no signal interference or
physical obstructions. May be

necessary to increase the
wireless communication range between the
access control system and the tracker
expansion board(s). See Repeater kit
instruction sheet for more information.

CVD

CVD

CVD

NC

C RE

C RE

C RE

LLOW

LLOW

LLOW

LO

ENY

ENY

TATU

TATU

TATU

Baseboard Reference

8

9

7

A

6

B

5

C

CH

4

D

3

E

2

F

1

0

8

9

7

A

6

B

5

C

NET

4

D

3

E

2

F

ID

1

0

ON - Only accepts card codes
from PAIRED tracker boards.

OFF - Normal Setting -

Allows card codes from paired
or unpaired tracker boards.

ON - Card code received - RECD

ON -Card code allowed - ALLOW

ON -Card code denied - DENY

Normal Data

Communication

ON - Communication lost - SYNC LOST

Blinking - receiving communication

from a tracker board or repeater.

(Board Power Monitoring) HEARTBEAT

LED Display

Jumper set on RIGHT

ON

side turns display ON.
(factory set) MUST

DISPLAY

OFF/

be ON to show RF
range and strength.

Y

DISPLA

/ON

F

OF

Jumper set on LEFT
side turns display OFF.
(50% board power
savings when OFF)

Important

All tracker expansion
boards and repeaters
MUST be set to SAME
ID number and channel
number as the wireless
baseboard.

Paired
Switch

ON

OFF

Not used - STATUS

SYNC REVD:

Blinking - Normal

RESET Button - Press to

reboot baseboard ONLY,
will not reset access
control board.

8

9

7

A

6

B

ON

OFF

PAIRED

RCVD

ALLOW

DENY

STATUS

5

C

4

D

3

E

2

F

1

0

8

9

7

A

6

B

5

C

4

D

3

E

2

F

1

0

RESET

DISPLAY

OFF/ON

Program Button - Press after

adjustment has been made to the

RF RANGE, RF ID or RF CHANNEL

before changes will take effect.

See “Wireless System Layout and Start-Up Procedure” for system
layout limitations, checking and adjusting RF range of the baseboard.

RF Range Adjustment

Set to max (full clockwise) for most applications. This may need
to be dialed back to limit the range when using a repeater.

RF Stat LED
UNPAIRED MODE:
Steady Red – Board is communicating with at least one unpaired tracker expansion board.
Blinking Red – Board is NOT communicating with ANY unpaired tracker expansion board.
PAIRED MODE:
Steady Green - Board is communicating with at least one paired tracker expansion board.
Blinking Green - Board is NOT communicating with ANY paired tracker expansion board.

RF Strength LED:
Updated every time a SYNC REVD signal is received.

CH

NET
ID

SYNC LOST

SYNC REVD

HEARTBEAT

RF
STAT STRENGTH

RF RANGE

PROG

DOORKING

2363-010

PAIR

RLY 1 RLY 2

Relay 1

Relay 2

DOORKING

2361-010

4-Pin Terminal

See previous page for terminal description.

Wires go to main terminal relays on access control system board.

PAIR Button - Press and hold 3 sec., SYNC REVD LED rapidly blinks blue.
This puts wireless baseboard into “Search Mode” to PAIR with all tracker
expansion boards.

Green - Strong signal - Normal
Yellow - Marginal signal - May lose communication.
Red - Poor signal - Unreliable

Antenna is REQUIRED.

10-Pin Terminal

14
13
12
11

6
5
4
3
2
1

See previous page for terminal description.

Connect Existing

Auxiliary Terminal

Access Control

System Power

Access Control System Relays LEDs

ON - Relay 2 Activated
ON - Relay 1 Activated

DoorKing Part Number

Power Transformer

16.5 VAC

REQUIRED

20 VA

polarity does not matter.
18 AWG 100 ft max
16 AWG 200 ft max

2361-080

Important Notice

Due to the nature of wireless communications, transmission and reception of data can never be guaranteed. Data may be delayed, corrupted (i.e.,
have errors) or be totally lost. Although significant delays or losses of data are rare when wireless devices are used in a normal manner with a
well-constructed network, DoorKing wireless products should not be used in situations where failure to transmit or receive data could result in
damage of any kind to the user or any other party, including but not limited to personal injury, death, or loss of property. DoorKing, Inc. accepts no
responsibility for damages of any kind resulting from delays or errors in data transmitted or received using DoorKing wireless products, or for
failure of DoorKing wireless products to transmit or receive such data.

Safety and Hazards

Do not operate DoorKing wireless products in areas where cellular modems are not advised without proper device certifications. These areas
include environments where cellular radio can interfere such as explosive atmospheres, medical equipment, or any other equipment which may
be susceptible to any form of radio interference. DoorKing wireless products can transmit signals that could interfere with this equipment. Do not
operate DoorKing wireless products in any aircraft, whether the aircraft is on the ground or in flight. In aircraft, DoorKing wireless products

MUST BE POWERED OFF. When operating, DoorKing wireless products can transmit signals that could interfere with various onboard systems.

Note: Some airlines may permit the use of cellular phones while the aircraft is on the ground and the door is open. DoorKing wireless products

may be used at this time.

The driver or operator of any vehicle should not operate DoorKing wireless products while in control of a
moving vehicle. Doing so will detract from the driver or operator’s control and operation of that vehicle. In
some states and provinces, operating such communications devices while in control of a vehicle is an offence.

2361-065-D-10-14 - Not for Release

Copyright 2014 DoorKing, Inc. All rights reserved.

Inglewood, California 90301

120 S. Glasgow Avenue

U.S.A.