D-Link DWL-1000AP+ Quick Install Guide
This product can be set up usingThis product can be set up using
This product can be set up using
This product can be set up usingThis product can be set up using
any current web browser, i.e.,any current web browser, i.e.,
any current web browser, i.e.,
any current web browser, i.e.,any current web browser, i.e.,
Internet Explorer 6 or NetscapeInternet Explorer 6 or Netscape
Internet Explorer 6 or Netscape
Internet Explorer 6 or NetscapeInternet Explorer 6 or Netscape
Navigator 6.2.3.Navigator 6.2.3.
Navigator 6.2.3.
Navigator 6.2.3.Navigator 6.2.3.
Before You BeginBefore You Begin
Before You Begin
Before You BeginBefore You Begin
It’s best to use a computer (with an Ethernet adapter) that is connected to a switch for
configuring the DWL-1000AP+. The default IP address for the DWL-1000AP+ is
192.168.0.50 with a Subnet Mask of 255.255.255.0. You will need to assign your
computer a Static IP address within the same range as the DWL-1000AP+’s IP address for the purpose of configuring the DWL-1000AP+. See the Manual on the CD-
ROM if you need assistance in assigning a Static IP address for your network
adapter.
Check Your Package ContentsCheck Your Package Contents
Check Your Package Contents
Check Your Package ContentsCheck Your Package Contents
DWL-1000AP+ Wireless Access
Point
DWL-1000AP+DWL-1000AP+
DWL-1000AP+
DWL-1000AP+DWL-1000AP+
D-Link D-Link
D-Link
D-Link D-Link
Wireless Access PointWireless Access Point
Wireless Access Point
Wireless Access PointWireless Access Point
AirAir
PremierPremier
Air
Premier
AirAir
PremierPremier
TMTM
TM
TMTM
CD-ROM (containing Manual and Warranty)
Ethernet (CAT5 UTP/Straight Through) Cable
Using a power supply
5V 2.5A DC Power Adapter
If any of the above items are missing, please contact your reseller.
©2002 D-Link Systems, Inc. All rights reserved. Trademarks or registered trademarks are the property of their respective holders. Software and
specifications subject to change without notice. DWL-1000AP+.11122002
2
with a different voltage
rating will damage and void
the warranty of this product.
FCC StatementFCC Statement
FCC Statement
FCC StatementFCC Statement
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communication. However, there is
no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of
the following measures:
¡E Reorient or relocate the receiving antenna.
¡E Increase the separation between the equipment and receiver.
¡E Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for
an uncontrolled
environment. This equipment should be installed and operated with a
minimum of 20 cm
(approximately 8 inches) between the radiator and your body.
3
Connecting The DWL-1000AP+ WirelessConnecting The DWL-1000AP+ Wireless
Connecting The DWL-1000AP+ Wireless
Connecting The DWL-1000AP+ WirelessConnecting The DWL-1000AP+ Wireless
Access Point To Your NetworkAccess Point To Your Network
Access Point To Your Network
Access Point To Your NetworkAccess Point To Your Network
A. First, connect the power adapter to the receptor at the back panel of
the DWL-1000AP+ and then plug the other end of the power adapter
to a wall outlet or power strip. The Power LED will turn ON to indicate
proper operation.
B. Using a Straight-Through Ethernet cable, insert one end of the cable to
the LAN ports on the back panel of the DWL-1000AP+ and the
other end of the cable to a switch. Note: The switch must be
connected to the computer to be used to configure the DWL 1000AP+. The Link LED light will illuminate to indicate a proper
Ethernet connection.
C. Computers with 802.11b wireless adapters can connect to the DWL-
1000AP+. The DWL-650+ AirPlus Wireless Cardbus Adapter and the
DWL-520+ AirPlus Wireless PCI Adapter will connect, out of the box,
with the DWL-1000AP+, using their default settings.
D. Antennas
Used to wirelessly
connect to 802.11b
adapters.
A. Receptor for
Power Adapter.
C. LAN PORTS
B. LAN PORTS
LAN port 2 is for
connecting to
another DWL-
1000AP+ to provide
redundency & load
balancing
Reset Button
Pressing this button restores
the Router to its original factory
default settings.
LAN port 1is for
connecting to a
switch on the local
network with an
ethernet cable
4
Loading...