D-Link DAP-X1870 Installation Manual
QUICK INSTALLATION CARD
www.dlink.com
Model Name: DEVICE
Wi-Fi Name: dlink-XXXX
Password: XXXXXXXX
S/N: 123456789
SETUP QR CODE
Quick Installation Guide
PACKAGE CONTENTS
ENGLISH
DAP-X1870
AX1800 Mesh Wi-Fi 6 Range Extender
INSTALLATION
D-LINK WI-FI APP SETUP
Plug the Range Extender into a power
1 / 2 /
outlet next to your router.
• DAP-X1870 || AX1800 Mesh Wi-Fi 6 Range Extender
• Quick Installation Guide
• Quick Installation Card
Download the D-Link Wi-Fi app
and launch it.
3 /
Tap Install New Device. Scan the QR
code on the Quick Installation Card.
Follow the on-screen instructions to
complete the setup.
SETUP QR CODE
D-Link Wi-Fi
Did you know? From automatic rmware updates to seeing what devices are connected to your network, the D-Link Wi-Fi app makes
setup and management of your Range Extender quick and simple.
FREQUENTLY ASKED QUESTIONS
?
Why can’t I connect to my wireless router or my wireless connection
drops?
1. Verify that your Range Extender is within range of your wireless router. Try
plugging it into a location closer to the router and verify the Status LED is
solid green.
2. Note that when extending a wireless signal from a router or access point,
devices connected to the Range Extender will not get the same speed/
throughput as when connected directly to the router.
D-Link Wi-Fi
Tip: Before you start, make sure you know
your current router’s Wi-Fi name and
password as you will need this info for setup.
What if I forgot my Range Extender’s Admin password
or want to reset my Range Extender?
1. If you forgot your Admin password or want to reset your
Range Extender back to the factory default settings, press
and hold the reset button on the bottom of the extender
using a paper clip and release after the Status light turns red.
Note: This process will erase all your settings.
2. Setup your Range Extender using your preferred method.
Reset
Button
Signal Strength Indicator
Very Weak (1 x Amber) Weak (1 x Green) Good (2 x Green) Strong (3 x Green)
How do I change the wireless settings on my Range Extender?
1. Open a web browser (e.g., Internet Explorer, Firefox, Chrome, or Safari) and
go to the URL found on the QIC or on the back of the Range Extender
(i.e., http://dlinkapXXXX.local./).
2. At the login screen, enter your Admin Password (If WPS Setup was used, the
password is “password” by default) and click Log in.
3. Go to Settings > Extender.
4. Enter a new Wi-Fi Network Name (SSID) and modify the security (Wi-Fi
password) settings as needed.
5. Click Save.
What is Mesh Smart Roaming?
With Mesh Smart Roaming, your Wi-Fi device (e.g. SmartPhone, Tablet) will
automatically roam to the strongest Wi-Fi signal, eliminating the need to
switch between your Router’s and Range Extender’s Wi-Fi signal as you
move around your home.
Mesh Smart Roaming Requirements:
1. The Wi-Fi device (e.g. SmartPhone, Tablet) must support the 802.11k/v
standard.
2. The Wireless Name (SSID) & Wireless Password must be the same
on both the Mesh Wi-Fi Range Extender and your Wireless Router.
How do I setup my Range Extender using WPS?
IMPORTANT
WPS may be disabled on some Routers or Modems. If the WPS Status LED on your Router or
Modem does not start blinking when you have pressed the WPS button, try again and hold it
a little longer. If it still does not blink, STOP, and congure your Range Extender using the
D-Link Wi-Fi App Setup.
1. Plug your Range Extender into an available outlet near your
wireless router and wait until the Status LED is blinking
amber (this may take up to 3 minutes). You can move it to a
more suitable location after it is set up. If the status LED does
not light up, ensure the power toggle switch underneath is
in the “on” position.
2. Press the WPS (Wi-Fi Protected Setup) button on your
wireless router for 3 seconds. An LED should start blinking
on your router. If it does not blink, see the important
note above.
3. Once confirmed that the WPS light is blinking on your router, within one
minute, press the WPS button on your Range Extender for 2-3 seconds.
The Status LED should start to blink green.
4. When the Status LED turns solid green (may take up to 3 minutes), this
indicates that your Range Extender is securely connected to your wireless
router.
Your setup is complete! You can now unplug and move your Range Extender
to a location between your Wireless Router and the area where you want
wireless coverage. By default, your Range Extender will share the same
Wi-Fi name and password as your Router. When using WPS setup, the default
Admin Password is “password”.
If after moving your Range Extender, the signal strength indicator is showing
one single amber bar or if your Range Extender LED does not turn solid green
within 3 minutes, move your Range Extender to a wall outlet closer to your
wireless router.
DLINK WIFI MESH
You can easily can pair your AX1800 Mesh Wi-Fi Range Extender
(DAP-X1870) with any D-Link Wi-Fi Mesh-enabled Router to create a
seamless mesh network that covers every corner of your home.
i
FCC WARNING
This device is complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
(1) The device may not cause harmful interface, and
(2) this device must accept any interface received, including interface that
may cause undesired operation.
TECHNICAL SUPPORT
Having trouble installing your new product? D-Link’s support website
contains live chat, commonly asked questions, the latest user
documentation and software updates for D-Link products.
United States
http://support.dlink.com
i
GPL CODE STATEMENT
This D-Link product includes software code developed by third parties, including software code
subject to the GNU General Public License (“GPL”)
or GNU Lesser General Public License (“LGPL”). As
applicable, the terms of the GPL and LGPL, and
information on obtaining access to the GPL code
and LGPL code used in this product, are available
to view the full GPL Code Statement at:
https://tsd.dlink.com.tw/GPL
The GPL code and LGPL code used in this product
is distributed WITHOUT ANY WARRANTY and is
subject to the copyrights of one or more authors.
For details, see the GPL code and the LGPL code
for this product and the terms of the GPL and
LGPL.
Written Oer for GPL and LGPL Source Code
Where such specific license terms entitle you
to the source code of such software, D-Link will
provide upon written request via email and/or
traditional paper mail the applicable GPL and LGPLsource code files via CD-ROM for a nominal cost
to cover shipping and media charges as allowed
under the GPL and LGPL.
Please direct all inquiries to:
Snail Mail: Email:
Attn: GPLSOURCE REQUEST
D-Link Systems, Inc.
17595 Mt. Herrmann Street
Fountain Valley, CA 92708
2020/08/07_90x130 v1.00(US) 610000010459
GPLCODE@dlink.com
Loading...