Digitech iStomp Owner’s Manual

O w n e r ’s M a n u a l

DECLARATION OF CONFORMITY

Manufacturer’s Name: DigiTech Manufacturer’s Address: 8760 S. Sandy Parkway

Sandy, Utah 84070, USA declares that the product:

With regard to Directive 2005/32/EC and EC Regulation 1275/2008 of 17 December 2008, this product is designed, produced, and classified as Professional Audio Equipment and thus is exempt from this Directive.

Product name:	iStomp
Product option:	all (requires Class II power adapter
	that conforms to the requirements
	of EN60065, EN60742, or
	equivalent.) DSC-iOS
conforms to the following Product Specifications:
Safety:	IEC 60065 -01+Amd 1
EMC:	EN 55022:2006
	EN 55024:1998
	FCC Part 15

Supplementary Information:

The product herewith complies with the requirements of the:

Low Voltage Directive 2006/95/EC EMC Directive 2004/108/EC. RoHS Directive 2002/95/EC WEEE Directive 2002/96/EC

EC Regulation 278/2009

Roger Johnsen

Director, Engineering

Signal Processing

8760 S. Sandy Parkway

Sandy, Utah 84070, USA

Date: December 9, 2011

European Contact:Your local DigiTech Sales and Service Office or

Harman Signal Processing

8760 South Sandy Parkway

Sandy, Utah

84070 USA

Ph: [phone]

Fax: [phone]

ELECTROMAGNETIC

COMPATIBILITY

This device complies with part 15 of the FCC Rules and the Product Specifications noted on the Declaration of Conformity. Operation is subject to the following two conditions:

•this device may not cause harmful interference, and

•this device must accept any interference received, including interference that may cause undesired operation.

Operation of this unit within significant electromagnetic fields should be avoided.

•use only shielded interconnecting cables.

Conforms to ICES-003

Conforme á ICES-003

Conforms to EN55022

If you want to dispose of this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery, and

recycling.

Private households in the 25 member states of the EU, in Switzerland and Norway may return their used electronic product free of charge to designated collection facilities or to a retailer (if you purchase a similar new one).

For countries not mentioned above, please contact your local authorities for a correct method of disposal.

By doing so you will ensure that your disposed product undergoes the necessary treatment, recovery, and recycling and thus prevent potential negative effects on the environment and human health.

Warning

For your protection, read the following:

Important Safety Instructions

1.Read these instructions.

2.Keep these instructions.

3.Heed all warnings.

4.Do not use this apparatus near water.

5.Clean only with dry cloth.

6.Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

7.Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

8.Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

9.Unplug this apparatus during lightning storms or when unused for long periods of time.

10.No user serviceable parts inside. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

11.WARNING:To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

12.Refer to labels on the unit, including bottom cover, or other markings and pertinent information.

Warranty

We at DigiTech® are very proud of our products and back up each one we sell with the following warranty:

1.Please register online at www.digitech.com within ten days of purchase to validate this warranty.

2.DigiTech warrants this product, when used solely within the U.S., to be free from defects in materials and workmanship under normal use and service.

3.DigiTech liability under this warranty is limited to repairing or replacing defective materials that show evidence of defect, provided the product is returned to DigiTech WITH RETURN AUTHORIZATION, where all parts and labor will be covered up to a period of one year.This warranty is extended, for the iStomp pedal hardware only, to a period of six years when the product has been properly registered through our website.A Return Authorization number may be obtained from DigiTech by telephone.The company shall not be liable for any consequential damage as a result of the product’s use in any circuit or assembly.

4.Proof-of-purchase is considered to be the burden of the consumer.

5.DigiTech reserves the right to make changes in design, or make additions to, or improvements upon this product without incurring any obligation to install the same on products previously manufactured.

6.The consumer forfeits the benefits of this warranty if the product’s main assembly is opened and tampered with by anyone other than a certified DigiTech technician or, if the product is used with AC voltages outside of the range suggested by the manufacturer.

7.The foregoing is in lieu of all other warranties, expressed or implied, and DigiTech neither assumes nor authorizes any person to assume any obligation or liability in connection with the sale of this product. In no event shall DigiTech or its dealers be liable for special or consequential damages or from any delay in the performance of this warranty due to causes beyond their control.

NOTE:The information contained in this manual is subject to change at any time without notification. Some information contained in this manual may also be inaccurate due to undocumented changes in the product or operating system since this version of the manual was completed.The information contained in this version of the owner’s manual supersedes all previous versions.

Introduction

Thank you for purchasing the DigiTech® iStomp™ Downloadable Pedal. The iStomp is a configurable stompbox which you can purchase and download different pedals into.The iStomp looks and performs just like a standard stompbox with control knobs,a footswitch,and a bypass/ active LED indicator,but provides much more flexibility than any other pedal available.

Using iOS devices as the programming interface,you can choose from a vast library of pedals and download them directly into the iStomp using the Stomp Shop™ app (available for free on the Apple® App Store™).Upgrading your pedals has just become as easy as a download!

Included Items

•	iStomp Downloadable Pedal	•	Owner’s Manual
•	DigiTech DSC-iOS Cable	•	iStomp Effect Labels
•	Power Supply	• DigiTech Redline™ Overdrive and
•	OnlineWarranty Registration		Total Recall™ Digital Delay pedals
	Information Card		included

1

Features

•4 knobs for controlling pedal settings

•Mono and stereo inputs & outputs

•Rugged metal footswitch

•DSC Download port

•Power supply included

•Free Stomp Shop™ App

•Growing library of great pedals to choose from

•Multiple pedal categories (including: Compression, Overdrive, Distortion, Chorus, Flanger, Phaser, Modulation, Pitch, Filter, Delay, Reverb, and more)

2

Requirements

•Any iOS device capable of running iOS 4.0 or later

•iTunes® account

•Internet connection to your iOS device

•Stomp Shop™ App (free download from the Apple® App Store™)

iPhone,iPodTouch,and iPad are trademarks of Apple Inc.,registered in the U.S.and other countries.

3

Pedal Interface

5

4
3											6
2							9			7
1										8

4

1.Indicator LED –This multi color LED indicates when the effect is turned on or off. If a delay pedal is downloaded into the iStomp, this LED will flash when used withTapTempo to show the delay time (see page 13“DelayTapTempo” for

information onTapTempo). Using the Stomp Shop app, the color of this LED can be customized for each downloaded pedal.

2.OUT 1 (Mono) Jack – Connect this output when only a single guitar amplifier is being used.

3.OUT 2 Jack – Connect this output to a second guitar amplifier when a second amp is being used.

4.DC Power Input – Connect only the included power supply to this jack.

5. Knobs –These knobs are used to control the pedal settings.The function of each of these knobs varies depending on which pedal has been loaded into the iStomp. Knob assignments for each pedal can be viewed in the“Info” window in the Stomp Shop app.

5