Denon DVD-3800BDCI User Manual

BLU-RAY DISC / DVD VIDEO PLAYER
DVD-3800BDCI
OPERATING INSTRUCTIONS MODE D’EMPLOI INSTRUCCIONES DE FUNCIONAMIENTO
Introduction
Introduction
Safety Precautions
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to consti tute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
Laser Safety
CAUTION:
VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN. DO NOT STARE INTO BEAM.
LOCATION: INSIDE, NEAR THE DECK MECHANISM.
CAUTION:
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. THIS PRODUCT SHOULD NOT BE ADJUSTED OR REPAIRED BY ANYONE EXCEPT PROPERLY QUALIFIED SERVICE PERSONNEL.
SAFETY INSTRUCTIONS
1. Read Instructions - All the safety and operating instructions should be read before the product is operated.
2. Retain Instructions - The safety and operatin g instructions should be retained for future reference.
3. Heed Warnings - All warnings on the product and in the operating instructions should be adhered to.
4. Follow Instructions - All operating and use instructions should be followed.
5. Cleaning - Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.
6. Attachments - Do not use attachments not recommended by the product manufacturer as they may cause hazards.
7. Water and Moisture - Do not use this product near water - for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like.
8. Accessories - Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.
9. A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.
10. Ventilation - Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to.
11. Power Sources - This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.
12. Grounding or Polarization - This product may be equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.
EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL
FIGURE A
ELECTRICAL CODE
GROUND CLAMP
ELECTRIC SERVICE EQUIPMENT
NEC - NATIONAL ELECTRICAL CODE
ANTENNA LEAD IN WIRE
ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)
GROUND CONDUCTORS (NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H)
13. Power-Cord Protection - Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.
14. Outdoor Antenna Grounding – If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. See Figure A.
15. Lightning - For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. This will prevent damage to the product due to lightning and power­line surges.
16. Power lines - An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.
17. Overloading - Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.
18. Object and Liquid Entry - Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.
19. Servicing - Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
20. Damage Requiring Service - Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a) When the power-supply cord or plug is damaged. b) If liquid has been spilled, or objects have fallen into the product. c) If the product has been exposed to rain or water. d) If the product does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to
restore the product to its normal operation. e) If the product has been dropped or damaged in any way. f) When the product exhibits a distinct change in performance - this indicates
a need for service.
21. Replacement Parts - When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.
22. Safety Check - Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.
23. Wall or Ceiling Mounting – The product should be mounted to a wall or ceiling only as recommended by the manufacturer.
24. Heat - The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.
I
ESPAÑOL FRANÇAIS ENGLISH
Introduction Introduction
FCC INFORMATION (For US customers)
1. PRODUCT
This product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this product may not cause harmful interference, and (2) this product must accept any interference received, including interference that may cause undesired operation.
2. IMPORTANT NOTICE: DO NOT MODIFY THIS PRODUCT
This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modification not expressly approved by DENON may void your authority, granted by the FCC, to use the product.
3. NOTE
This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This product generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this product does cause harmful interference to radio or television reception, which can be determined by turning the product OFF and ON, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the product into an outlet on a circuit different from that to which the receiver is connected.
• Consult the local retailer authorized to distribute this type of product or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Note on use / Observations relatives a l’utilisation / Notas sobre el uso
• Keep the apparatus free from moisture, water, and
Avoid high temperatures. Allow for sucient heat dispersion when installed in a rack.
• Eviter des températures élevées Tenir compte d’une dispersion de chaleur susante lors de l’installation sur une étagère.
• Evite altas temperaturas Permite la suciente dispersión del calor cuando está instalado en la consola.
dust.
Protéger l’appareil contre l’humidité, l’eau et lapoussière.
Mantenga el equipo libre de humedad, agua y polvo.
• Unplug the power cord when not using the apparatus for long periods of time.
• Débrancher le cordon d’alimentation lorsque l’appareil n’est pas utilisé pendant de longues périodes.
Desconecte el cordón de energía cuando no utilice el equipo por mucho tiempo.
• Do not let foreign objects into the apparatus.
• Ne pas laisser des objets étrangers dans l’appareil.
• No deje objetos extraños dentro del equipo.
• Do not let insecticides, benzene, and thinner come
• Ne pas mettre en contact des insecticides, du
in contact with the apparatus.
benzène et un diluant avec l’appareil. No permita el contacto de insecticidas, gasolina y diluyentes con el equipo.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LAFICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
Copyrights / Droits d’auteur / Derechos de Autor
• It is prohibited by law to reproduce, broadcast, rent or play discs in public without the consent of the copyright holder.
• La reproduction, la diffusion, la location, le prêt ou la lecture publique de ces disques sont interdits sans le consentement du détenteur des droits d’auteur.
• De acuerdo con las leyes está prohibido reproducir, emitir, alquilar o interpretar discos en público sin la autorización del propietario de los derechos de autor.
• Handle the power cord carefully. Hold the plug when unplugging the cord.
• Manipuler le cordon d’alimentation avec précaution. Tenir la prise lors du débranchement du cordon.
Maneje el cordón de energía con cuidado. Sostenga el enchufe cuando desconecte el cordón de energía.
II
* (For apparatuses with ventilation holes)
• Do not obstruct the ventilation holes.
• Ne pas obstruer les trous d’aération.
• No obstruya los oricios de ventilación.
• Never disassemble or modify the apparatus in any way.
• Ne jamais démonter ou modier l’appareil d’une manière ou d’une autre.
• Nunca desarme o modique el equipo de ninguna manera.
ENGLISH
Introduction Introduction
Contents Features
Introduction
Features .................................................................................... 1
Advanced AL24 Processing ..................................................... 2
Important ................................................................................. 2
Power Supply ........................................................................... 2
Warning .................................................................................... 2
Installation Location ................................................................ 2
Cautions on Installation .......................................................... 2
Caution on Handling ............................................................... 3
Dew Warning ............................................................................ 3
Avoid the Hazards of Electrical Shock and Fire ..................... 3
Before Using ............................................................................. 3
About Copyright ...................................................................... 3
Supplied Accessories ............................................................... 3
Trademark Information ........................................................... 3
About Discs .............................................................................. 4
Disc Handling ...........................................................................................4
Cleaning Discs .......................................................................................... 4
Playable Discs and Files ........................................................................4
Unplayable Discs .....................................................................................5
Color Systems ...........................................................................................5
Region Codes ...........................................................................................5
Structure of Disc/SD Memory Card Contents ............................... 5
Symbols Used in this Operating Instructions ...............................5
About the Remote Control ...................................................... 6
Loading the Batteries ............................................................................6
Using a Remote Control .......................................................................6
Setting this Unit not React to Other DENON’s DVD Player's
Remote Control ....................................................................................6
Changing the Signal Code of a Remote Control .........................6
Part Names and Functions ...................................................... 7
Front Panel ................................................................................................7
Rear Panel ..................................................................................................7
Remote Control .......................................................................................8
Front Panel Display ................................................................................9
Adjusting the Brightness of the Display ......................................... 9
Examples of Displays during Operation .........................................9
Connections
Connecting to a TV .............................................................................. 10
Connecting to a Display Device with HDMI Cable ................... 10
Connecting to a Display Device and an Amplifier/
Receiver with HDMI Cable ............................................................. 10
HDMI Output Mode and Actual Output Signals ....................... 11
Audio Setting ........................................................................................ 11
Digital Connection to an AV Amplifier with
Built-in Decoder ................................................................................ 12
Connection to a Device with 2-channels of
Analog Audio Inputs ........................................................................13
Surround Connections to a Device with 7.1/
5.1-channels of Analog Audio Inputs ........................................13
Connecting the AC cord .................................................................... 13
Playback
Turning the Power On ............................................................14
Direct Playback .......................................................................14
Operations Using Disc Menu, Title Menu, and
Popup Menu .........................................................................15
Playing Back a VR mode DVD-RW/-R ...................................15
Pause .......................................................................................15
Resume Playback ....................................................................16
Fast Forward / Fast Reverse Playback ..................................16
Slow Forward Playback ..........................................................16
Step by Step Playback ............................................................16
Dialog Speed ...........................................................................17
Repeat Playback .....................................................................17
A-B Repeat ..............................................................................................17
Program Playback ..................................................................18
Random Playback ...................................................................18
Zoom .......................................................................................19
Camera Angle .........................................................................19
Search ......................................................................................19
On-Screen Display ..................................................................20
Selecting the Format of Audio and Video ............................22
Selecting Audio Streams/Channels ............................................... 22
Selecting Subtitle Language ............................................................22
Virtual Surround ...................................................................................23
Pure Direct Mode .................................................................................23
Setting the BD Audio Mode .............................................................23
Adjusting the Picture .......................................................................... 24
Playing Back an MP3, Win dows Media™ Audio,
JPEG and DivX® File .............................................................25
Kodak Picture CD .................................................................................. 27
Reading the SD Memory Card ...............................................27
Function Setup
Using the Setup Menu ........................................................................ 29
Quick .......................................................................................29
Custom ...................................................................................29
Initialize ..................................................................................37
Others
Troubleshooting .....................................................................38
Language Code .......................................................................39
Specifications .........................................................................40
HDMI (High-Definition Multimedia Interface)
You can enjoy clearer video output when connecting this unit to a display device with an HDMI-compatible port.
Dialog Speed
Playback in slightly faster speed while keeping the sound output. Dialog speed is available only on discs recorded in the Dolby Digital format.
Still/Fast/Slow/Step Playback
Various playback modes are available including still pictures, fast forward/reverse, slow motion and step frames.
Still Mode
The resolution of pictures while in the still (pause) mode can be adjusted.
Random Playback for audio CD, MP3, JPEG, and Windows Media™ Audio
This unit can shuffle the playback order of tracks/files.
Program Playback for audio CD, MP3, JPEG, and Windows Media™ Audio
You can program the playback order of tracks/files in a desired order.
BD/DVD Menus in a Desired Language
You can display BD/DVD menus in a desired language, if available on a BD/DVD.
Auto Power Off
The power turns off automatically if there is no activity at the unit or its remote control for more than 30 minutes (refer to page
37).
Subtitles in a Desired Language
You can select a desired language for subtitles if that language is available on the BD/DVD and DivX
Selecting a Camera Angle
You can select a desired camera angle if a disc contains sequences recorded from different angles.
Choices for Audio Language and Sound Mode
You can select a desired audio language and sound mode if different languages and modes are available on a disc.
Ratings Control (Parental Lock)
You can set the control level to limit playback of discs which may not be suitable for children.
Automatic Detection of Discs
This unit automatically detects if a loaded disc is BD, DVD, audio CD, MP3, JPEG, Windows Media™ Audio or DivX
Pure Direct
The sound quality of analog audio output is improved by stop output of video signals, etc.
®
.
®
.
1
ENGLISH
ENGLISH
Introduction Introduction
On-Screen Display
Information about the current operation can be displayed on a screen, allowing you to confirm the currently active functions (such as program playback) using the remote control.
Dimmer
The brightness of the front panel display can be adjusted.
Screen Saver
The screen saver program starts if there is no activity at the unit or its remote for more than 5 minutes. The brightness of the display is darken by 75%. The program is deactivated when there is any activity.
Picture Control
Picture control adjusts black level and noise reduction of the specific display.
Search
Chapter search: Search for a desired chapter. Title search: Search for a desired title. Track search: Search for a desired track/file. Time search: Search for a desired time point or a title or a
track/file.
Repeat
Chapter: Repeated playback of a chapter of the disc. Title: Repeated playback of a title of the disc. Track: Repeated playback of a track/file of the disc. All: Repeated playback of the entire disc.
(not available for BD, DVD-video) A-B: Repeated playback of a part between two points. Group: Repeated playback of a folder of the MP3/JPEG/
Windows Media™ Audio/DivX
®
disc being played
back is possible.
Zoom
x1.2, x1.5, x2.0, x4.0 magnified image can be displayed. (not available for BD)
Marker
Electric reference points designated by user can be called back.
Resume Playback
User can resume playback from the point at which the playback has been stopped even if the power is turned off.
Bit Rate Indication
The bit rate (the amount of video data currently being read) can be displayed during the playback of video contents. (not available for BD)
DRC (Dynamic Range Control)
Use this procedure to set the dynamic range of the output signals when playing back DVD/BD recorded in Dolby Digital/ Dolby Digital Plus/Dolby TrueHD.
Displaying a JPEG picture
Kodak Picture CD can be played back. Still images stored in JPEG format on DVD-RW/-R, CD-RW/-R or SD Memory Card can also be played back.
Playing Back Windows Media™ Audio File
You can enjoy Windows Media™ Audio files which are recorded on DVD-RW/-R, CD-RW/-R or SD Memory Card.
Playing Back an MP3 File
You can enjoy MP3 files which are recorded on DVD-RW/-R, CD-RW/-R or SD Memory Card.
Playing Back DivX
You can enjoy DivX CD-RW/-R.
• Official DivX
• Plays all versions of DivX
®
File
®
files which are recorded on DVD-RW/-R or
®
Certified product
®
video (including DivX® 6) with
standard playback of DivX® media files.
Playing Back the Contents in SD Memory Card
• You can playback MP3, Windows Media™ Audio, or JPEG stored in an SD Memory Card.
• You can store picture-in-picture commentary, subtitles or other extras for BD-ROM Profile 1.1 files in an SD Memory Card and playback with the BD-ROM.
BD-J Application
• With some BD that supports Java applications (BD-J), you can enjoy interactive function (e.g., game).
Analog 7.1ch Surround Output
This player is equipped with analog 7.1-channel surround audio out jacks for playback.
Advanced AL24 Processing
“Advanced AL24 Processing” which greatly increases the amount of information in the time axis area using unique high speed signal detection and processing technology for the PCM signal BD/DVD/CD playback circuitry is provided for 2-channel output. In addition to expansion of data to 24 bits, natural signal correction without marring the original data is performed with upconversion sampling.
In addition, DENON’s original analog waveform reproduction technology, “AL24 Processing PLUS”, is used for the 7.1-channel audio output, resulting in high sound quality for all PCM signal sources.
The “Advanced AL24” indicator lights on the front panel when Advanced AL24 Processing is activated.
Important
Use only discs marked with logos listed on page 4.
Power Supply
The main power supply is engaged when the main plug is plugged in a 120V, 60Hz AC outlet. To operate the unit, press
<B ON / A OFF> to turn on the unit.
Warning
To avoid fire or electric shock, do not expose this unit to rain or moisture.
WARNING: LIVE PARTS INSIDE. DO NOT REMOVE ANY SCREWS.
Installation Location
For safety and optimum performance of this unit:
• Do not stand the unit up vertically. Install the unit in a horizontal and stable position. Do not place anything directly on top of the unit. Do not place the unit directly on top of the TV.
• Shield it from direct sunlight and keep it away from sources of intense heat. Avoid dusty or humid places. Avoid places with insufficient ventilation for proper heat dissipation. Do not block the ventilation holes on the sides of the unit. Avoid locations subject to strong vibration or strong magnetic fields.
• Be sure to remove a disc and unplug the AC cord from the outlet before carrying the unit.
Non-use periods - Turn off the unit when it is not in use. Unplug the unit from the household AC outlet if it is not to be used for a long time. Unplug the unit during lightning storms.
Please read this operating instructions carefully before using the unit, and keep it for future reference.
Cautions on Installation
Noise or disturbance of the picture may be generated if this unit or any other electronic equipment using microprocessors is used near a tuner or TV. If this happens, take the following steps:
• Install this unit as far as possible from the tuner or TV.
• Set the antenna wires from the tuner or TV away from this unit’s AC cord and input/output connection cords.
• Noise or disturbance tends to occur particularly when using indoor antennas or 300/ohms feeder wires. We recommend using outdoor antennas and 75/ohms coaxial cables.
Note
• For heat dispersal, do not install this equipment in a
confined space such as a book case or similar unit.
2
ENGLISH
ENGLISH
Introduction Introduction
Cautions on using mobile phones.
Before turning the power operation button on.
Sufficiently ventilate the place of installation.
Moisture condensation may occur inside the unit when it is moved from a cold place to a warm place, or after heating a cold room or under conditions of high humidity. Do not use the unit at least for 2 hours until its inside is dry.
• Do not handle the AC cord with wet hands.
• Do not pull on the AC cord when disconnecting it from AC wall
• If, by accident, water is spilled on this unit, unplug the AC cord
10 cm or more
Advanced AL24
ON / STANDBY
ON
OFF
VIDEO NR
SD CARD
BLU-RAY DISC PLAYER
VIDEO NOISE
HDMI
REDUCTION
RESOLUTION
DVD-3800BDCI
Wall
Caution on Handling
Using a mobile phone near this unit may result in noise. If so, move the mobile phone away from this unit when it is in use.
Check once again that all connections are correct and that there are not problems with the connection cables. Always set the power operation button to the standby position before connecting and disconnecting connection cables.
If the unit is left in a room full of the smoke from cigarettes, etc., for long periods of time, the surface of the optical pickup could get dirty, in which case it will not be able to read the signals properly.
Dew Warning
Avoid the Hazards of Electrical Shock and Fire
outlet. Grasp it by the plug.
immediately and take the unit to our authorized service center for servicing.
Before Using
Pay attention to the following before using this unit:
Moving the unit.
To prevent short-circuits or damaged wires in the connection cables, always unplug the power supply cord and disconnect the connection cables between all other audio components when moving the unit.
Store the operating instructions in a safe place.
After reading the operating instructions, store them in a safe place as they could come in handy in the future.
Whenever <ON/STANDBY> is in the STANDBY state, the unit is still connected to AC line voltage.
Please be sure to press <B ON / A OFF> to turn off the power or unplug the cord when you leave home for, say, a vacation.
Note that the illustrations in these instructions may differ from the actual unit for explanation purposes.
The serial number of this product may be found on the back of the unit. No others have the same serial number as yours. You should record the number and other vital information here and retain this book as a permanent record of your purchase to aid identification in case of theft.
Date of Purchase Dealer Purchase from Dealer Address Dealer Phone No. Model No. Serial No.
About Copyright
Unauthorized copying, broadcasting, public performance and lending of discs are prohibited.
This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision.
Reverse engineering or disassembly is prohibited.
U. S. Patent No’s, 4,631,603; 4,819,098; 4,907,093; 5,315,448 and 6,516,132.
Supplied Accessories
Please check to make sure the following items are included with the main unit in the carton.
remote control (RC-1090) “AA” (R6P) batteries x2
AC cord operating instructions
service station list warranty card
RCA audio cable RCA video cable
Trademark Information
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.
Manufactured under license under U.S. Patent #’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,487,535 & other U.S. and worldwide patents issued & pending. DTS and DTS Digital Surround are registered trademarks and the DTS logos and Symbol are trademarks of DTS, Inc. © 1996-2007 DTS, Inc. All Rights Reserved.
3
ENGLISH
ENGLISH
Introduction Introduction
Java and all other trademarks and logos are trademarks or registered trademarks of Sun Microsystems, Inc. in the United States and/or other countries.
DivX, DivX Certified, and associated logos are trademarks of DivX, Inc. and are used under license.
Windows Media and the Windows logo are trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries.
“Blu-ray Disc” and are trademarks.
is a trademark of DVD Format/Logo Licensing Corporation.
is trademark of Eastman Kodak Company.
About Discs
Disc Handling
• Handle the discs so that fingerprints and dust do not adhere to the surfaces of the discs.
• Always store the disc in its protective case when it is not used.
• Note that discs with special shapes cannot be played on this product. Do not attempt to play back such discs, as they may damage the unit.
Cleaning Discs
• When a disc becomes dirty, clean it with a cleaning cloth. Wipe the disc from the center to out. Do not wipe in a circular motion.
• Do not use solvents such as benzine, thinner, commercially available cleaners, detergent, abrasive cleaning agents or antistatic spray intended for analog records.
Playable Discs and Files
This unit is compatible to play back the following discs. To play back a BD or DVD, make sure that it meets the requirements for region codes and color systems as described on page 5. You can play back discs that have the following logos on the disc. Other disc types are not guaranteed to play back.
Playable discs Logos
Blu-ray Disc
-BD-video
- BD-RE (ver.2.1) (Recorded in BDMV format)
-BD-R (Recorded in BDMV format) (Unclosed discs may not be played back.)
DVD-video
DVD-RW (Finalized discs only)
DVD-R DVD-R DL
CD-DA (audio CD)
CD-RW
CD-R
Kodak Picture CD
DTS - CD (5.1 Music Disc)
Playable files Logos Media
MP3
Windows Media™ Audio
JPEG
(Finalized discs only)
DVD-RW/-R CD-RW/-R SD Memory Card (including SDHC) miniSD Card microSD Card
Note
• Discs containing the DivX® files with the DivX®GMC (Global Motion Compensation) playback feature, which is DivX supplemental function, cannot be played back on this unit.
• This unit cannot play back the disc contents protected by Windows Media™ Digital Rights Management (DRM).
• “WMA” (Windows Media™ Audio) is an audio codec developed by Microsoft® in the United States of America.
• This unit supports AAC as an audio format recorded with video contents for BD-R, BD-RE. This unit does not support AAC as an independent audio file.
Readable cards Playable files / data
SD Memory Card (8MB - 2GB) SDHC Memory Card (4GB) miniSD Card (8MB - 2GB) microSD Card (8MB - 2GB)
MP3, Windows Media™ Audio, JPEG, Picture-in-picture commentary, subtitles or other extras for BD-ROM Profile 1.1
®
Note for SD Memory Cards
• Do not remove the SD Memory Card or turn off the unit while the contents of the card is in playback. It may result in malfunction or loss of the card’s data.
• Please keep the SD Memory Cards in their cases when you are not using them.
• Do not try to open or modify the card.
• Do not touch the terminal surface with your fingers or any metals.
• Do not attach additional labels or stickers to cards.
• Do not remove the label of the SD Memory Cards.
• This unit supports SD Memory Card with FAT12/FAT16 file system, and SDHC Memory Card with FAT32 file system.
• This unit may not read the SD Memory Cards formatted on computer. If that is the case, please reformat the SD Memory Cards on this unit and try again.
• This unit does not supports mini SDHC and micro SDHC Memory Card.
• For miniSD Card and microSD Card adapter is necessary.
miniSD Card Adapter
miniSD Card
• Portions of this product are protected under copyright law and are provided under license by ARIS/SOLANA/4C.
microSD Card Adapter
microSD Card
DivX
®
DVD-RW/-R CD-RW/-R
4
ENGLISH
ENGLISH
Introduction Introduction
The following discs will not play back on this unit. BD and DVD are recorded in different color systems throughout
Unplayable Discs
• BD-RE Ver.1.0 (BD-disc with cartridge)
• BD contains MP3/ Windows Media™ Audio/ JPEG/ DivX® files
• BD/DVD hybrid disc (e.g., Total Hi Def hybrid disc)
• BD-video that does not include "A" on its region code.
• DVD-video that does not include either "1" nor "ALL" on its region code.
• DVD-ROM/RAM (For DVD-ROM discs, data files in DivX
5.x and 6 can be played)
• DVD-RW/-R recorded in non-compatible recording format
• CD-ROM (Data files in DivX® 3.11, 4.x, 5.x and 6 can be played)
• CDV (Only the audio part can be played)
• CD-G (Only the audio signals can be output)
• CompactDisc-Interactive (CD-I)
• Video Single Disc (VSD)
• Video CD, Super Video CD
• Super audio CD (Only the sound on the CD layer can be heard. The sound on the high-density super audio CD layer cannot be heard.)
•DVD-audio
• HD DVD
• Disc with recording area less than 55mm in diameter
• Unauthorized disc (Pirated disc)
• Unfinalized disc
®
3.11, 4.x,
Color Systems
the world. The most common color system is NTSC (which is used primarily in the United States and Canada). This unit uses NTSC, so BD or DVD you play back must be recorded in the NTSC system. You cannot play back BD or DVD recorded in other color systems.
Region Codes
This unit has been designed to play back BD with region A and DVD-video with region 1. You cannot play back BD or DVD-video that are labeled for other regions. Look for the symbols on the right on your BD or DVD-video. If these region symbols do not appear on your BD or DVD-video, you cannot play back the disc in this unit. The letter or number inside the globe refers to region of the world. A BD or DVD-video labeled for a specific region can only play back on the unit with the same region code.
BD-video
DVD-video
Structure of Disc/SD Memory Card Contents
The contents of BD / DVD are generally divided into titles. Titles may be further subdivided into chapters.
BD/DVD
title 1 title 2
chapter 1 chapter 2 chapter 1 chapter 2 chapter 3
Audio CDs are divided into tracks.
track 1 track 2 track 3 track 4 track 5
Audio CD
audio CD
Symbols Used in this Operating Instructions
To specify for which media type each function is, we put the following symbols at the beginning of each item to operate.
Symbol Description
BD-V
DVD-V
DVD-VR
CD
MP3
WMA
JPEG
DivX
If you do not find any of the symbols listed above under the function heading, the operation is applicable to all media.
Button name only:
Description refers to BD-video and BD-RE (ver. 2.1)/ BD-R recorded in BDMV format
Description refers to DVD-video and DVD-RW/-R recorded in video mode
Description refers to DVD-RW/-R recorded in VR mode
Description refers to audio CD and DTS-CD
Description refers to DVD-RW/-R, CD-RW/-R and SD Memory Card with MP3 files
Description refers to DVD-RW/-R, CD-RW/-R and SD Memory Card with Windows Media™ Audio files
Description refers to DVD-RW/-R, CD-RW/-R and SD Memory Card with JPEG files
Description refers to DVD-RW/-R and CD-RW/-R with DivX
®
files
®
About the button names in this explanation
< > : Buttons on the main unit [ ] : Buttons on the remote control
Buttons on the main unit and remote control
Data discs or SD Memory Cards contains MP3/Windows Media™ Audio/JPEG/DivX® is divided into folders, and the folders are
subdivided into files.
MP3, Windows Media™ Audio, JPEG, DivX
folder (group) 1 folder (group) 2
group(folder)1 group(folder)2
file (track) 1 file (track) 2 file (track) 3 file (track) 4 file (track) 5
MP3, WMA, JPEG, DivX®
®
5
ENGLISH
ENGLISH
Introduction Introduction
About the Remote Control
Loading the Batteries
A Open the battery
compartment cover.
B Insert two “AA” (R6P)
batteries, with each one oriented correctly.
Using a Remote Control
Keep in mind the following when using the remote control:
• Make sure that there are no obstacles between the remote control and infrared sensor window on the unit.
• Remote operation may become unreliable if strong sunlight or fluorescent light is shining on infrared sensor window of the unit.
• Remote control for different devices can interfere with each other. Avoid using remote control for other equipment located close to the unit.
• Replace the batteries when you notice a fall off in the operating range of the remote control.
• The maximum operable ranges from the unit are as follows.
- Line of sight: approx. 23 feet (7m)
- Either side of the center: approx. 23 feet (7m) within 30°
Changing the Signal Code of a Remote Control
To avoid the other DENON’s BD players responding the remote signal of this unit, you can change the signal code of the remote control. If the signal code of the remote control does not match to the signal code of the unit, you cannot control the unit with the remote control.
Change the signal code of the unit
1) In stop mode, press [SETUP].
2) Use [Y / Z] to select , then press [ENTER].
3) Use [Y / Z] to select , then press [ENTER].
4) Use [U / V] to select “Remote Control Setting”.
5) Press [ENTER] to select “DENON1” or “DENON2”.
C Close the cover.
Cautions on Batteries
• Use “AA” (R6P) batteries in this remote control.
• Replace the batteries with new ones approximately once a year, though this depends on the frequency with which the remote control is used.
• If the remote control does not operate within a close proximity of the main unit, replace the batteries with new ones, even if less than a year has passed.
• The included batteries serve only for verifying operation. Replace them with new batteries as soon as possible.
• When inserting the batteries, be careful to do so in the proper direction, following the and marks in the remote control’s battery compartment.
• To prevent damage or battery fluid leakage:
- Do not mix a new battery with an old one.
- Do not mix two different types of batteries such as alkaline
and manganese.
- Do not short-circuit, disassemble, heat or dispose of
batteries in flames.
• Remove the batteries when not planning to use the remote control for a long period of time.
• If the batteries should leak, carefully wipe off the fluid from the inside of the battery compartment, then insert new batteries.
Advanced AL24
ON / STANDBY
ON
OFF
VIDEO NR
SD CARD
BLU-RAY DISC PLAYER
VIDEO NOISE
HDMI
REDUCTION
RESOLUTION
DVD-3800BDCI
30°30°
23 feet (7m) 30° 23 feet (7m) 23 feet (7m) 30°
Setting this Unit not React to Other DENON’s DVD Player's Remote Control
If you have other DENON’s DVD players around this unit, this unit reacts to the commands you made for DVD players through its remote control. To avoid this situation, you can set this unit not react to other DENON’s DVD player's remote control.
1) In stop mode, press [SETUP].
2) Press [7],[8],[9],[2].
3) Press [SETUP].
• “Only Attached Remocon” will be displayed on the upper right corner of the screen and this unit only react to the commands from this unit's remote control.
• To set back to default, press [7],[8],[9],[1] at step 2. “Normal
Remocon” will be displayed on the upper right corner of the screen and this unit react to both the commands from this unit's remote control and the other DENON’s DVD players' remote control.
Note
• The setting remains after you turn off this unit or unplug the AC cord.
• If you try to operate this unit with the other DENON’s DVD players' remote control, some of the operation may not available depends on the manufactured year or type of the remote control.
Others
Power Saving Off Remote Control Setting DENON1 Media Select Disc
6) Press [SETUP] to exit.
• At this point the new signal code of the unit is effective. Please change the signal code of the remote control to match to the signal code of the unit with following procedure.
Change the signal code of the remote control
Set to “DENON1”: Press and hold [RETURN], and press [3], [2], [1].
Set to “DENON2”:
Press and hold [RETURN], and press [1], [2], [3].
• If the signal code does not match, the signal code of the remote control will be displayed on the front panel display.
• The default setting and the setting after you change the batteries is “DENON1”.
6
ENGLISH
ENGLISH
Introduction Introduction
Part Names and Functions
Front Panel
11
9
ON / STANDBY
ON
2
1
The unit can also be turned on by pressing the buttons with circled numbers.
1. Power indicator
This indicator lights up in green when the power is on, and lights up in red when in standby mode.
2. ON/STANDBY button
Press to turn the unit to standby mode. In standby mode, this unit still consume small amount of power.
3. B ON / A OFF (POWER) switch
Press to turn the unit on and off. If you turn off the unit using this switch, the unit does not consume power. In this condition, this unit does not accept any button except this switch.
4. Advanced AL24 indicator
Indicates that audio signals of a BD, DVD, etc., are being processed digitally with the Advanced AL24 Processing.
5. VIDEO NR indicator
Indicates that video signals of a BD, DVD, etc., are being processed digitally with the DNR (Digital Noise Reduction) processing.
6. Infrared sensor window
Receives signals from your remote control so that you can control the unit from a distance.
7. Display
Refer to “Front Panel Display” on page 9.
Advanced AL24
OFF
VIDEO NR
67 8345
8. SD CARD slot
Insert an SD Memory Card, and play back the contents in it.
9. Disc tray
Place a disc when opening the disc tray.
10. A (OPEN/CLOSE) button
Press to open or close the disc tray.
11. B (PLAY) button
Press to start or resume playback.
12. C (STOP) button
Press to stop playback.
13. H / G (SKIP DOWN/UP) button
Press to skip down/up titles/chapters/tracks/files.
14. h / g (FAST FORWARD/REVERSE) button
Press to search forward / backward through a disc.
15. F (STILL/PAUSE) button
Press to pause playback.
16. VIDEO NOISE REDUCTION button
Press repeatedly to reduce the overall level of noise on the picture (DNR). Each time you press the button, the level of the DNR switches “Off”
17. HDMI RESOLUTION button
Press to set the HDMI jack’s video signal output mode.
10
SD CARD
A
“+1”A“+2”A“+3” A“Off”.
12 13
HDMI
RESOLUTION
BLU-RAY DISC PLAYER
DVD-3800BDCI
17 16
VIDEO NOISE
REDUCTION
14
Rear Panel
16 9
(
)
PCM / BITSTREAM
DIGITAL OUT
OPTICAL
15
FR
SW SR SL SBR SBLC
1. DIGITAL OUT (OPTICAL/COAXIAL) jack
Use digital audio coaxial/optical cable to connect to an AV receiver, Dolby Digital decoder or other device with a digital audio coaxial/optical input jack.
2. 7.1ch AUDIO OUT jacks
Use an RCA audio cable to connect these jacks to the 7.1-channel audio input jacks of your amplifier with 7.1-channel input terminals.
3. 2ch AUDIO OUT jacks
Use an RCA audio cable to connect these jacks to the 2-channel audio input jacks of your amplifier with 2- channel input terminals.
4. VIDEO OUT jack
Use an RCA video cable to connect to a TV monitor, AV receiver or other device.
5. S VIDEO OUT jack
Use an S-video cable to connect to the S-video input jack of external device.
6. HDMI OUT jack
Use an HDMI cable to connect to a display with an HDMI input jack.
7. COMPONENT VIDEO OUT jacks
Use a component video cable to connect to a display device with component input jacks.
7
ENGLISH
COAXIAL
FL
2ch
AUDIO OUT
7.1ch
AUDIO OUT
VIDEO OUT
HDMI OUT
RS-232C
STRAIGHT CABLE
R
IN
ROOM TO ROOM
REMOTE CONTROL
S VIDEO OUT
Y
PB/CBPR/C
COMPONENT VIDEO OUT
8. REMOTE CONTROL IN / OUT jacks
Connecting the DENON Satellite Remote Control to these jacks enables you to operate more than one DENON components with one remote control.
9. CONTROL CONNECTOR (RS-232C)
This is a terminal for future system extension.
10. AC IN Terminal
Use to connect the AC cord to supply the power.
Note
• Do not touch the inner pins of the jacks on the rear panel. Electrostatic discharge may cause permanent damage to the unit.
AC IN
OUT
108234 57
ENGLISH
Introduction Introduction
Remote Control
10
12
14 16
18
20
The unit can also be turned on by pressing the buttons with circled numbers.
31
1
2
30
3
4
29
5
6
7
28
8
9
27
11
26
13 15
25
24
17
19
23
22
21
1. POWER ON button
• Press to turn the unit on.
2. POWER OFF button
• Press to turn the unit to standby mode.
3. A-B REPEAT button
• Press to mark a segment between A and B for A-B repeat playback.
4. REPEAT button
• Press to select the repeat mode.
5. RANDOM button
• Press to display the random playback screen for shuffling the playback order of tracks/files.
6. ZOOM button
• During playback, press to enlarge the picture on the screen.
7. CLEAR button
• Press to clear the information once entered, to clear the marker settings, or to cancel the programming for CD, etc.
8. RED/GRN/BLU/YEL button
• Press to select item on some BD menus.
9. TOP MENU button
• Press to display the top menu.
10. Cursor U / V / Y / Z buttons
• Press to select items or settings.
11. ENTER button
• Press to confirm or select menu items.
12. SETUP button
• Press to display the setup menu.
13. ANGLE button
• Press to access various camera angles on the disc.
• Press to rotate the JPEG/Kodak Picture images.
14. SUBTITLE button
• Press to display the subtitle menu.
15. PURE DIRECT button
• Press to stop output of video signals, etc., and output only the analog audio signals to achieve high quality sound from analog audio outputs.
16. DISPLAY button
• Press to display the On-Screen display menu.
17. SKIP H button
• During playback, press to return to the beginning of the current title chapter, track or file.
18. SKIP G button
• During playback, press to skip the next chapter, track or file.
19. STOP C button
• Press to stop playback.
• Press to exit from the title menu.
20. REW h button
• During playback, press to fast reverse the playback.
21. STILL/PAUSE F button
• Press to pause playback.
• When playback is in pause, press repeatedly to forward the playback step by step.
22. FFW g button
• During playback, press to fast forward the playback.
• When playback is in pause, press to slow forward the playback.
23. PLAY B button
• Press to start playback or resume playback.
24. MODE button
• During playback, press to display the picture adjustment menu, and rapid playback.
• During the JPEG playback, press to display menus for changing the visual effect for switching the image or changing the size of the image.
• In stop mode with BD inserted, press to display a menu for setting the BD audio mode.
• In stop mode with BD or DVD inserted, press to display a menu for setting the virtual surround.
• In stop mode with audio CD, or disc with MP3, Windows Media™ Audio, JPEG files inserted, press to display menus for program and random playback.
25. AUDIO button
• Press to display the audio menu.
26. RETURN button
• Press to return to the previously displayed menu screen.
27. POP UP MENU / MENU button
• Press to display the disc menu.
28. SEARCH MODE button
• Press to display the search menu.
29. Number buttons
• Press to enter the title/chapter/track/file numbers.
30. OPEN/CLOSE A button
• Press to open or close the disc tray.
31. DIMMER button
• Press to adjust the brightness of the front panel display.
Note
[ZOOM] and [RANDOM] are not available for BD.
8
ENGLISH
ENGLISH
Introduction Introduction
Front Panel Display
VCD
1A-B
11
13
GROUP TI TLE TRACK TOTA L SI NG REMCHA P
12 8 710 9
HD DVD
BD SD USB NET
1
PROG RAND
2 3 5 64
14
Examples of Displays during Operation
Display Description
Power on
2 CH MULTIHDMISUP ER AUD IO
DIGITAL + DTS Tr u e HD D TS- H D VSS MP3 WMA
PL x HDCD ANGL E
L. PCM MPEG .MIX
AΑC
Standby mode
Tray open
Tray is closing
Loading the disc
1. B : Appears when playing back a disc. F : Appears when playback is paused.
2. Appears during program playback.
3. Appears during random playback.
4. Appears during repeat playback.
5. These indicate the format being decoded.
• This is not a indication of the recorded
format or the format that will be output.
6. Appears when playing back a multi angle disc.
7. Appears when playing back a multi-channel audio disc.
8. Appears when playing back a 2-channel
REM : Appears when displaying
remaining time.
10. These indicate the type of the different sections of the currently playing disc.
11. Appears when HDMI video or audio signals are being output. Does not appear when HDMI connection is not verified.
12. Indicates the type of the currently playing disc.
13. Appears when inserting an SD Memory Card.
14. Appears various type of information on the disc, the elapsed playing time, etc.
audio disc.
9. Indicates the time display mode. TOTAL : Appears when displaying the
total remain/elapsed time of audio CD.
SING : Appears when sound data is
being played or sound data is highlighted in program menu.
Adjusting the Brightness of the Display
You can adjust the brightness of the display by the pressing [DIMMER] repeatedly. The brightness changes as bright A dimmer A auto each time you press [DIMMER]. If you select auto, the display gets dimmer during playback.
No disc inserted
No SD Memory Card inserted
This unit cannot read the disc or SD Memory Card inserted.
Stop mode.
HDMI output mode(480i) is selected.
HDMI output mode(480p) is selected.
HDMI output mode(720p) is selected.
HDMI output mode(1080i) is selected.
HDMI output mode(1080p) is selected.
HDMI output mode(1080p24 frame) is selected.
Pure direct mode is set to pure direct off.
Pure direct mode is set to front panel display off.
Pure direct mode is set to video signal off.
Pure direct mode is set to video signal and front panel off.
The total number of the track that has been registered for the program playback and track number currently selected.
The total number of the files that has been registered for the program playback and folder/file number currently selected.
When the root folder is selected “ROOT” is displayed.
"All Clear" for program playback setting is selected.
Note
• When playing back the disc that contains more than 100 titles, display of the chapter and time on the front panel display will be moved a few dots to the right.
9
ENGLISH
Connections
ENGLISH
Connections
Connecting to a TV
Make one of the following connections, depending on the capabilities of your existing device.
Method 1 Method 2 Method 3
analog audio
standard picture
good picture better picture
display device
COMPONENT
VIDEO IN
Y
P
B/CB
PR/C
R
component video cable
(Green)
(When RCA cable
connected)
(Red)
(Blue)
P
BRR
YB/C P /C
COMPONENT VIDEO OUT
VIDEO OUT
(Green)
(Blue)
(Red)
COMPONENT
VIDEO IN
Y
P
B
P
R
component video cable
or
(Green)
(Blue)
Y
COMPONENT VIDEO OUT
COMPONENT
VIDEO OUT
(When BNC cable
connected)
(Green)
(Blue)
(Red)
(Red)
P
B
P
RCA
audio
cable
AUDIO IN
LR
VIDEO
IN
RCA video cable
and or or
S-VIDEO IN
S-video cable
this unit
(
)
PCM / BITSTREAM
DIGITAL OUT
COAXIAL
OPTICAL
FR
FL
2ch
AUDIO OUT
SW SR SL SBR SBLC
AUDIO OUT
7.1ch VIDEOOUT
LR
AUDIO OUT
2ch
R
Y
PB/CBPR/C
SVIDEO OUT
COMPONENTVIDEO OUT
VIDEO OUT
S VIDEO OUT
2ch AUDIO OUT VIDEO OUT S VIDEO OUT COMPONENT
Supplied cables used in this connection are as follows:
• RCA audio cable (L/R) x 1
• RCA video cable x 1 Please purchase the rest of the necessary cables at your local store.
Note
• Connect this unit directly to the TV. If the RCA audio/video cables are connected to a VCR, pictures may be distorted due to the copy protection system.
• If the display device to which the player is to be connected is compatible with progressive scan video, connect to the component video input or HDMI input jack.
• If you use the method 3 to display device not compatible with the progressive scan video, set “Component Output” to “480i”.
• If the picture is not output properly to the display device because of the “HDMI Video Resolution” or “Component Output” setting, press and hold B on the front panel for more than 5 seconds. The “HDMI Video Resolution” setting will be reset to the default automatically.
Connecting to a Display Device with HDMI Cable
Connecting this unit to device with an HDMI jack using an HDMI cable enables digital transfer of both digital video signals and multi-channel audio signals.
After making the connection, please make HDMI settings on setup menu according to your display device. Refer to page 30-32.
Method 4
best audio and picture
display device
OPTICAL
FR
SW SR SL SBR SBLC
(
)
PCM / BITSTREAM
DIGITAL OUT
COAXIAL
FL
AUDIO OUT
2ch
7.1ch
AUDIO OUT
To HDMI Input jack
A display device with an HDMI compatible port
Cables not included.
Please purchase the necessary cables at your local store.
R
Connecting to a Display Device and an Amplifier/Receiver with HDMI Cable
Connecting this unit to display device and an amplifier/receiver with an HDMI jack using HDMI cables enables digital surround sound with high quality video.
Front Speaker (left)
Center
Speaker
display device
HDMI IN HDMI OUT
HDMI cable
Surround Speaker (left)
Surround back (For
7.1-channel) (left)
Surround back (For
7.1-channel) (right)
this unit
HDMI cable
Front Speaker (right)
amplifier
HDMI OUT
VIDEO OUT
S VIDEO OUT
HDMI IN
Subwoofer
Surround Speaker (right)
this unit
(
)
PCM / BITSTREAM
DIGITAL OUT
COAXIAL
OPTICAL
FR
FL
2ch
AUDIO OUT
SW SR SL SBR SBLC
7.1ch
AUDIO OUT
HDMI cable
HDMI OUT
VIDEO OUT
S VIDEO OUT
Cables not included.
Please purchase the necessary cables at your local store.
10
ENGLISH
ENGLISH
Connections Connections
Press <HDMI RESOLUTION> to select the HDMI output mode. HDMI video resolution changes as following.
HDMI Output Mode and Actual Output Signals
Front Panel Display HDMI Video Resolution
480 Interlaced
Press <HDMI RESOLUTION>
480 Progressive
Press <HDMI RESOLUTION>
720 Progressive
Press <HDMI RESOLUTION>
1080 Interlaced
Press <HDMI RESOLUTION>
1080 Progressive
Press <HDMI RESOLUTION>
1080 Progressive 24 frame
Press <HDMI RESOLUTION>
Note
• You can change the HDMI output mode with the <HDMI RESOLUTION> during playback as
well.
• After you select a HDMI output mode, corresponding HDMI video resolution will be output. The HDMI video resolution you selected will be output even if the connected display device is not compatible with the HDMI video resolution. If there is no image displayed on the connected display device, please select another HDMI video resolution.
• Video and audio signals may distorted temporarily when switching to/from the HDMI output mode.
• You can also change the HDMI output mode from “HDMI Video Resolution” in the “Video” menu on the setup menu. In this menu, you can confirm what HDMI video resolutions are supported by connected display device. Refer to page 31.
• In order to get natural and high quality film reproduction of 24-frame film material, use HDMI cable (High Speed HDMI cable is recommended) and select “1080p24” if the connected display device is compatible with 1080p24 frame input.
• Even if you set to “1080p24” for the “HDMI Video Resolution”, when the contents of the disc is not compatible for 1080p24 frame, 1080p60 frame will be output.
• If connected display device does not support 1080p24 frame or “I/P Direct” is set to “Off”, “1080p24” will not be available.
• “1080p24” can be displayed on the front panel, only when the connected display device supports the HDMI resolution.
• There is no output from VIDEO OUT, S VIDEO OUT and COMPONENT VIDEO OUT jacks when you play back a BD that recorded 24-frame film material.
• COMPONENT VIDEO OUT jacks may not output any signals when you set “HDMI Select” to “RGB” or “HDMI Deep Color” to “Auto”.
Audio Setting
When using HDMI connections make the “HDMI Audio Out” settings in the “Audio” menu on the setup menu according to the specifications of the device or monitor to be connected.
Device to be connected “HDMI Audio Out” setting Output HDMI audio signal
Device compatible with DTS, DTS-HD, Dolby Digital, Dolby Digital Plus or Dolby TrueHD decoding
HDMI Multi(Normal) Dolby Digital, Dolby Digital Plus,
Dolby TrueHD, DTS, or DTS-HD bitstream are output from HDMI OUT. Make the speaker settings on the connected AV amplifier, etc.
Device compatible with 3 or more channels of audio inputs (not DTS, DTS-HD, Dolby Digital, Dolby Digital Plus or Dolby TrueHD compatible)
HDMI Multi(LPCM)
Multi-channel audio signals are output from the HDMI terminal. Make the speaker settings with the speaker setting items appear after you select “HDMI Multi(LPCM)”. Refer to page 32.
Device compatible with 2-channel audio input or device not compatible with audio input
HDMI connection to a display device, and digital audio connection (coaxial/optical) to an AV amplifier.
HDMI 2ch Down-mixed 2-channel audio
signals are output from HDMI OUT.
Audio Mute HDMI audio will be muted, and
Dolby Digital/DTS bitstream or LPCM will be output from DIGITAL OUT depending on the “Digital Out” setting. Refer to page 12.
Audio signals output from HDMI OUT
Disc type Audio recording
BD-video
format
Dolby Digital Dolby Digital Plus Dolby TrueHD DTS DTS-HD
HDMI Multi(Normal) HDMI Multi(LPCM) HDMI 2ch Dolby Digital* Dolby Digital Plus* Dolby TrueHD*
1
DTS* DTS-HD*
1
LPCM Multi LPCM Multi LPCM 2ch Downmix LPCM
BD-RE/BD-R
AAC Multi LPCM Multi LPCM 2ch Downmix LPCM LPCM Multi LPCM Multi LPCM 2ch Downmix LPCM Dolby Digital Dolby Digital Multi LPCM 2ch Downmix LPCM
DVD-video
DTS DTS Multi LPCM 2ch Downmix LPCM LPCM Multi LPCM Multi LPCM 2ch Downmix LPCM
®
DivX
audio CD/ MP3/Windows
Dolby Digital Dolby Digital Multi LPCM 2ch Downmix LPCM MP3/MP2 2ch LPCM 2ch LPCM 2ch LPCM
2ch LPCM 2ch LPCM 2ch LPCM
Media™ Audio DTS-CD DTS Multi LPCM 2ch Downmix LPCM
“HDMI Audio Out” setting
1
1
Multi LPCM 2ch Downmix LPCM
1
Multi LPCM* Multi LPCM* Multi LPCM 2ch Downmix LPCM Multi LPCM*
2
3
4
2ch Downmix LPCM 2ch Downmix LPCM
2ch Downmix LPCM
11
ENGLISH
Loading...
+ 30 hidden pages