DENON AVR-2801 User Manual [fr]

AV SURROUND RECEIVER
RÉCEPTEUR AUDIO-VIDÉO

AVR-2801/981

OPERATING INSTRUCTIONS
MODE D’EMPLOI

2 We greatly appreciate your purchase of the AVR-2801/981.
2 To be sure you take maximum advantage of all the features the AVR-2801/981 has to offer, read these instructions

carefully and use the set properly. Be sure to keep this manual for future reference should any questions or
problems arise.

2 Nous vous remercions de l’achat de l’AVR-2801/981.
2 Pour être sûr de profiter au maximum de toutes les caractéristiques qu’a à offrir l’AVR-2801/981, lire avec soin ces

instructions et bien utiliser l’appareil. Toujours conserver ce mode d’emploi pour s’y référer ultérieurement en cas
de question ou de problème.

FOR ENGLISH READERS PAGE 02 ~ PAGE 053
POUR LES LECTEURS FRANCAIS PAGE 2, 54 ~ PAGE 103

ENGLISH

2

2 SAFETY PRECAUTIONS

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK). NO USER­SERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.

The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.

CAUTION

TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG
TO WIDE SLOT, FULLY INSERT.

ATTENTION

POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTERODUIRE LA
LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE
CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’ AU
FOND.

This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.

This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du
Règlement sur le matériel brouilleur du Canada.

“SERIAL NO.
PLEASE RECORD UNIT SERIAL NUMBER ATTACHED TO THE REAR OF THE
CABINET FOR FUTURE REFERENCE”

“NO. DE SERIE
PRIERE DE NOTER LE NUMERO DE SERIE DE L’APPAREIL INSCRIT A L’ARRIERE
DU COFFRET DE FAÇON A POUVOIR LE CONSULTER EN CAS DE PROBLEME.”

WARNING:

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.

•

FOR CANADA MODEL ONLY

•

POUR LES MODELE CANADIEN UNIQUEMENT

FRANCAIS

2 NOTE ON USE / OBSERVATIONS RELATIVES A L’UTILISATION

• Avoid high temperatures.
Allow for sufficient heat dispersion when
installed on a rack.

• Eviter des températures élevées
Tenir compte d’une dispersion de chaleur
suffisante lors de l’installation sur une étagère.

• Handle the power cord carefully.
Hold the plug when unplugging the cord.

• Manipuler le cordon d’alimentation avec
précaution.
Tenir la prise lors du débranchement du cordon.

• Keep the set free from moisture, water, and
dust.

• Protéger l’appareil contre l’humidité, l’eau et
lapoussière.

• Unplug the power cord when not using the set
for long periods of time.

• Débrancher le cordon d’alimentation lorsque
l’appareil n’est pas utilisé pendant de longues
périodes.

* (For sets with ventilation holes)

• Do not obstruct the ventilation holes.

• Ne pas obstruer les trous d’aération.

• Do not let foreign objects in the set.

• Ne pas laisser des objets étrangers dans
l’appareil.

• Do not let insecticides, benzene, and thinner
come in contact with the set.

• Ne pas mettre en contact des insecticides, du
benzène et un diluant avec l’appareil.

• Never disassemble or modify the set in any
way.

• Ne jamais démonter ou modifier l’appareil
d’une manière ou d’une autre.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

3

SAFETY INSTRUCTIONS

1. Read Instructions – All the safety and operating instructions
should be read before the appliance is operated.

2. Retain Instructions – The safety and operating instructions
should be retained for future reference.

3. Heed Warnings – All warnings on the appliance and in the
operating instructions should be adhered to.

4. Follow Instructions – All operating and use instructions
should be followed.

5. Water and Moisture – The appliance should not be used
near water – for example, near a bathtub, washbowl,
kitchen sink, laundry tub, in a wet basement, or near a
swimming pool, and the like.

6. Carts and Stands – The appliance should be used only with
a cart or stand that is recommended by the manufacturer.

6A. An appliance and cart

combination should be
moved with care.
Quick stops, excessive
force, and uneven
surfaces may cause
the appliance and cart
combination to overturn.

7. Wall or Ceiling Mounting – The appliance should be
mounted to a wall or ceiling only as recommended by the
manufacturer.

8. Ventilation – The appliance should be situated so that its
location or position does not interfere with its proper
ventilation. For example, the appliance should not be
situated on a bed, sofa, rug, or similar surface that may
block the ventilation openings; or, placed in a built-in
installation, such as a bookcase or cabinet that may impede
the flow of air through the ventilation openings.

9. Heat – The appliance should be situated away from heat
sources such as radiators, heat registers, stoves, or other
appliances (including amplifiers) that produce heat.

10. Power Sources – The appliance should be connected to a
power supply only of the type described in the operating
instructions or as marked on the appliance.

11. Grounding or Polarization – Precautions should be taken so
that the grounding or polarization means of an appliance is
not defeated.

12. Power-Cord Protection – Power-supply cords should be
routed so that they are not likely to be walked on or pinched
by items placed upon or against them, paying particular
attention to cords at plugs, convenience receptacles, and
the point where they exit from the appliance.

14. Cleaning – The appliance should be cleaned only as
recommended by the manufacturer.

15. Power Lines – An outdoor antenna should be located away
from power lines.

16. Outdoor Antenna Grounding – If an outside antenna is
connected to the receiver, be sure the antenna system is
grounded so as to provide some protection against voltage
surges and built-up static charges. Article 810 of the
National Electrical Code, ANSI/NFPA 70, provides
information with regard to proper grounding of the mast and
supporting structure, grounding of the lead-in wire to an
antenna-discharge unit, size of grounding conductors,
location of antenna-discharge unit, connection to grounding
electrodes, and requirements for the grounding electrode.
See Figure A.

17. Nonuse Periods – The power cord of the appliance should
be unplugged from the outlet when left unused for a long
period of time.

18. Object and Liquid Entry – Care should be taken so that
objects do not fall and liquids are not spilled into the
enclosure through openings.

19. Damage Requiring Service – The appliance should be
serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged; or
B. Objects have fallen, or liquid has been spilled into the

appliance; or
C. The appliance has been exposed to rain; or
D. The appliance does not appear to operate normally or

exhibits a marked change in performance; or
E. The appliance has been dropped, or the enclosure

damaged.

20. Servicing – The user should not attempt to service the
appliance beyond that described in the operating
instructions. All other servicing should be referred to
qualified service personnel.

FIGURE A

EXAMPLE OF ANTENNA GROUNDING

AS PER NATIONAL
ELECTRICAL CODE

ANTENNA
LEAD IN
WIRE

GROUND
CLAMP

ELECTRIC
SERVICE
EQUIPMENT

ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)

GROUNDING CONDUCTORS
(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)

NEC - NATIONAL ELECTRICAL CODE

ENGLISH

4

2

INTRODUCTION

2

ACCESSORIES

Thank you for choosing the DENON AVR-2801/981 Digital Surround A / V receiver. This remarkable component has been engineered to provide
superb surround sound listening with AV theater sources such as DVD, as well as providing outstanding high fidelity reproduction of your favorite
music sources.
As this product is provided with an immense array of features, we recommend that before you begin hookup and operation that you review the
contents of this manual before proceeding.

TABLE OF CONTENTS

z Before Using ……………………………………………………………………4
x Cautions on Installation ………………………………………………………4
c Cautions on Handling …………………………………………………………5
v Features …………………………………………………………………………5
b Connections …………………………………………………………………6~11
n Part Names and Functions ………………………………………………12, 13
m Setting up the system ……………………………………………………14~22
, Remote Control Unit………………………………………………………23~31

. Operation …………………………………………………………………31~35
⁄0 Surround ……………………………………………………………………36~39
⁄1 DSP Surround Simulation…………………………………………………40~44
⁄2 Listening to the Radio …………………………………………………45~47
⁄3 Last Function Memory ………………………………………………………47
⁄4 Initialization of the Microprocessor …………………………………………47
⁄5 Troubleshooting…………………………………………………………………48
⁄6 Additional Information ……………………………………………………49~52
⁄7 Specifications …………………………………………………………………53

Check that the following parts are included in addition to the main unit:

q Operating instructions…..1 w Warranty ( for North America model only )………...........1 e Service station list…….....1 r Remote control unit

t R6P/AA batteries….....….2 y AM loop antenna…...............1 u FM indoor antenna…1 i FM antenna adaptor….....1 (RC-881)............…......1

1

2

BEFORE USING

CAUTIONS ON INSTALLATION

Pay attention to the following before using this unit:

• Moving the set

To prevent short circuits or damaged wires in the connection cords,
always unplug the power cord and disconnect the connection cords
between all other audio components when moving the set.

• Before turning the power switch on

Check once again that all connections are proper and that there are
not problems with the connection cords. Always set the power
switch to the standby position before connecting and disconnecting
connection cords.

Noise or disturbance of the picture may be generated if this unit or
any other electronic equipment using microprocessors is used near a
tuner or TV.
If this happens, take the following steps:

• Install this unit as far as possible from the tuner or TV.

• Set the antenna wires from the tuner or TV away from this unit’s
power cord and input/output connection cords.

• Noise or disturbance tends to occur particularly when using indoor
antennas or 300 Ω/ohms feeder wires. We recommend using

outdoor antennas and 75 Ω/ohms coaxial cables.

For heat dispersal, leave at least 10 cm of space between the top,
back and sides of this unit and the wall or other components.

• Store this instructions in a safe place.

After reading, store this instructions along with the warranty in a
safe place.

• Note that the illustrations in this instructions may differ from

the actual set for explanation purposes.

10 cm or more

10 cm or more

Wall

ENGLISH

5

3

CAUTIONS ON HANDLING

4

FEATURES

• Switching the input function when input jacks are not
connected

A clicking noise may be produced if the input function is switched
when nothing is connected to the input jacks. If this happens, either
turn down the MASTER VOLUME control or connect components
to the input jacks.

• Muting of PRE OUT jacks, HEADPHONE jack and SPEAKER

terminals

The PRE OUT jacks, HEADPHONE jacks and SPEAKER terminals
include a muting circuit. Because of this, the output signals are
greatly reduced for several seconds after the power switch is
turned on or input function, surround mode or any other-set-up is
changed. If the volume is turned up during this time, the output will
be very high after the muting circuit stops functioning. Always wait
until the muting circuit turns off before adjusting the volume.

• Whenever the power switch is in the STANDBY state, the

apparatus is still connected on AC line voltage.
Please be sure to unplug the cord when you leave home for,
say, a vacation.

1. Dolby Digital

Using advanced digital processing algorithms, Dolby Digital
provides up to 5.1 channels of wide-range, high fidelity surround
sound. Dolby Digital is the default digital audio delivery system for
North American DVD and DTV.

2. DTS (Digital Theater Systems)

DTS provides up to 5.1 channels of wide-range, high fidelity
surround sound, from sources such as laser disc, DVD and
specially-encoded music discs.

3. 24 bit D/A Conversion

All six channels, including the five main channels and the low
frequency effects (LFE) channel benefit from reference, for
optimum high fidelity reproduction of music and movie
soundtracks.

4. Video Select Function

Allow you to watch one source (visual) while listening to another
source (audio).

ENGLISH

6

IN

IN

OUT

SIGNAL
GND

DVD

EXT. INANTENNA

VDP

TV

/

DBS

VCR-2/
V.AUX

COAXIAL

VCR-2/
V.AUX

CDR/
TAPE

CDR/
TAPE

VCR-1

VCR-1OPT.-1

OPT.-2

OPT.-3

FR

LOOP
ANT.

AM

FM
COAX.
75

SW

SR

CD

PHONO

FL

C

SL

SPEAKER SYSTEMS

AUDIO

DIGITAL

C-VIDEO

MONITOR

S-VIDEO

PRE OUT

L

R L

R L

R L

R L

R L

R

B

R L

A

FRONTSURROUND

SURROUND CENTER FRONT FRONT

SUB

CENTER

WOOFER

RLR

L

R

INPUT OUTPUT

LRL

R

OUTPUT

L

R

L

SWITCHED

TOTAL 120W(1A.)MAX.

AC 120V 60HZ

AC OUTLETS

OUTPUT

OPTICAL COAXIAL

OUTPUT

OPTICAL

L

R

L

R

L

R

L

R

DIGITAL AUDIODIGITAL AUDIO

DIGITAL AUDIODIGITAL AUDIO

L

R

5

CONNECTIONS

• Do not plug in the AC cord until all connections have been completed.

• Be sure to connect the left and right channels properly (left with left, right
with right).

• Insert the plugs securely. Incomplete connections will result in the
generation of noise.

• Use the AC OUTLETS for audio equipment only. Do not use them for

hair driers, etc.

• Note that binding pin plug cords together with AC cords or placing them
near a power transformer will result in generating hum or other noise.

• Noise or humming may be generated if a connected audio equipment is
used independently without turning the power of this unit on. If this
happens, turn on the power of the this unit.

Connecting the audio components

• When making connections, also refer to the operating instructions of the other
components.
The power to these outlets is turned on and off when the power is switched
between on and standby from the remote control unit or power switch.

CD player

Connecting a CD player

Connect the CD player’s analog output
jacks (ANALOG OUTPUT) to this unit’s
CD jacks using pin plug cords.

Connecting a turntable

Connect the turntable’s output cord to the
AVR-2801/981’s PHONO jacks, the L (left)
plug to the L jack, the R (right) plug to the
right jack.

NOTE:

This unit cannot be used with MC
cartridges directly. Use a separate head
amplifier or step-up transformer.

If humming or other noise is generated
when the ground wire is connected,
disconnect the ground wire.

Turntable
(MM cartridge)

Ground
wire

Use these jacks if you wish to connect external power
amplifier(s) to increase the power of the front, center and
surround channels, or for connection to powered loudspeakers.
Connect the internal amplifier‘s subwoofer to the subwoofer
terminal. (Refer to page 11.)

AC OUTLETS

• SWITCHED
(total capacity – 120 W (1 A.))

The power to these outlets is turned on and off in conjunction with
the POWER operation switch on the main unit, and when the power
is switched between on and standby from the remote control unit.
No power is supplied from these outlets when this unit’s power is at
standby. Never connect equipment whose total capacity is above
120 W (1 A.).

NOTE:

Only use the AC OUTLETS for audio equipment. Never use them for
hair driers, TVs or other electrical appliances.

Connecting the AC OUTLTETS

AC 120 V, 60 Hz

Connecting a tape deck

Connections for recording:

Connect the tape deck’s recording input jacks (LINE IN or REC) to this
unit’s tape recording (CDR/TAPE OUT) jacks using pin plug cords.

Connections for playback:

Connect the tape deck’s playback output jacks (LINE OUT or PB) to this
unit’s tape playback (CDR/TAPE IN) jacks using pin plug cords.

Tape deck or CD recorder

Route the connection cords, etc., in such a way that they do not obstruct
the ventilation holes.

MD recorder, DAT deck or other component
equipped with digital output jacks

CD player or other
component equipped
with digital output jacks

Connecting the DIGITAL jacks

Use these for connections to audio equipment with digital output. Refer to page
20, 21 for instructions on setting this terminal.

NOTES:

• Use 75 Ω/ohms cable pin cords for coaxial connections.

• Use optical cables for optical connections, removing the cap before
connecting.

Connecting the pre-out jacks

Power supply cord

ENGLISH

7

IN

IN

OUT

SIGNAL
GND

DVD

EXT. IN

VDP

TV

/

DBS

VCR-2/
V.AUX

COAXIAL

VCR-2/
V.AUX

CDR/
TAPE

CDR/
TAPE

VCR-1

VCR-1OPT.-1

OPT.-2

OPT.-3

FR

LOOP
ANT.

AM

FM
COAX.
75

SW

SR

CD

PHONO

FL

C

SL

SPEAKER SYSTEMS

AUDIO

DIGITAL

C-VIDEO

MONITOR

S-VIDEO

PRE OUT

L

R L

R L

R L

R L

R L

R

L

R

B

R L

A

FRONT

SURROUND

SURROUND CENTER FRONT FRONT

SUB

CENTER

WOOFER

9kHz

10kHz

IN

DVD

IN

VIDEO

R
L

R OUT IN

AUDIO

VIDEO

OUT IN

LRL

R

L

R

L

R OUT IN

AUDIO

VIDEO

OUT IN

LRL

R

L

R

L

R OUT

VIDEO

OUT

L

AUDIO

L

R

R OUT

VIDEO

OUT

L

AUDIO

L

R

R
L
R
L
R
L
R
L

R
L

ANTENNA

Connecting video components

• To connect the video signal, connect using a 75 Ω/ohms video signal cable cord. Using an improper cable can result in a drop in video quality.

• When making connections, also refer to the operating instructions of the other components.

TV or DBS tuner

Connecting a TV/DBS tuner

TV/DBS

• Connect the TV’s or DBS tuner’s video output jack (VIDEO OUTPUT) to the

(yellow) TV/DBS IN jack using a 75 Ω/ohms video coaxial pin plug cord.

• Connect the TV’s or DBS tuner’s audio output jacks (AUDIO OUTPUT) to the
TV/DBS IN jacks using pin plug cords.

AUDIO

VIDEO

DVD player or video disc player (VDP)

Connecting a DVD player or a video disc player (VDP)

VDP

• Connect the video disc player’s video output jack (VIDEO OUTPUT) to the (yellow)

VDP/DVD IN jack using a 75 Ω/ohms video coaxial pin plug cord.

• Connect the video disc player’s analog audio output jacks (ANALOG AUDIO OUTPUT) to the
VDP/DVD IN jacks using pin plug cords.

• A DVD player can be connected to the DVD jacks in the same way.

• It is also possible to connect a video disc player, DVD player, video camcorder, game machine,

etc., to the VCR-2/V.AUX jacks.

AUDIO

VIDEO

Monitor TV

MONITOR OUT

• Connect the TV’s video
input jack (VIDEO INPUT)
to the MONITOR
OUT jack using a 75
Ω/ohms video coaxial pin
plug cord. (See pages 21.)

VIDEO

Note on connecting the digital input jacks

• Only audio signals are input to the digital input jacks.
For details, see page 6.

Video deck 2

Video deck 1

Connecting a video decks

• There are two sets of video deck (VCR) jacks, so two video decks can be connected for simultaneous recording or video copying.

Video input/output connections:

• Connect the video deck’s video output jack (VIDEO OUT) to the (yellow) VCR-1 IN jack, and the video deck’s video input jack (VIDEO IN) to the

(yellow) VCR-1 OUT jack using 75 Ω/ohms video coaxial pin plug cords.

Connecting the audio output jacks

• Connect the video deck’s audio output jacks (AUDIO OUT) to the VCR-1 IN jacks, and the video deck’s audio input jacks (AUDIO IN) to the VCR-1
OUT jacks using pin plug cords.

*

Connect the second video deck to the VCR-2/V.AUX jacks in the same way.

AUDIOAUDIO

VIDEOVIDEO

ENGLISH

8

IN

IN

OUT

SIGNAL
GND

DVD

EXT. INANTENNA

VDP

TV

/

DBS

VCR-2/
V.AUX

COAXIAL

VCR-2/
V.AUX

CDR/
TAPE

CDR/
TAPE

VCR-1

VCR-1OPT.-1

OPT.-2

OPT.-3

FR

LOOP
ANT.

AM

FM
COAX.
75

SW

SR

CD

PHONO

FL

C

SL

SPEAKER SYSTEMS

AUDIO

DIGITAL

C-VIDEO

MONITOR

S-VIDEO

PRE OUT

L

R L

R L

R L

R L

R L

R

B

R L

A

FRONT

SURROUND CENTER FRONT FRONT

SUB

CENTER

WOOFER

VOLTAGE SELECTOR

115V 230V

AC OUTLET

SAME AS LINE-VOLTAGE

SWITCHED 100W MAX.

9kHz

10kHz

OUT

S-VIDEO

IN

S-VIDEO

OUT

S-VIDEO

IN OUT

S-VIDEO

IN OUT

S-VIDEO

Connecting a video component equipped with S-Video jacks

• When making connections, also refer to the operating instructions of the other components.

• A note on the S input jacks

The input selectors for the S inputs and pin jack inputs work in conjunction with each other.

• Precaution when using S-jacks

This unit’s S-jacks (input and output) and video pin jacks (input and output) have independent circuit structures, so that video signals input from
the S-jacks are only output from the S-jack outputs and video signals input from the pin jacks are only output from the pin jack outputs.
When connecting this unit with equipment that is equipped with S-jacks, keep the above point in mind and make connections according to the
equipment’s instruction manuals.

DVD player or video disc player (VDP)

Connecting a DVD player or a video disc player (VDP)

VDP

• Connect the video disc player’s S-Video output jack to the S­VIDEO VDP IN jack using an S-Video connection cord.

• A DVD player can be connected to the DVD jacks in the same
way.

• It is also possible to connect a video disc player, DVD player,
video camcorder, game machine, etc., to the VCR-2/V.AUX
jacks.

Connecting a monitor TV

MONITOR OUT

• Connect the TV’s S video input (S-VIDEO INPUT) to the MONITOR
OUT jack using a S jack connection cord.

S-VIDEO

Monitor TV

Connecting a TV/DBS tuner

• Connect the TV’s or DBS tuner’s
S video output jack (S-VIDEO
OUTPUT) to the
TV/DBS IN jack using an S jack
connection cord.

S-VIDEO

TV or satellite broadcast tuner

Video deck 1

Connecting the video decks

• Connect the video deck’s S output jack (S-OUT) to the
VCR-1 IN jack and the video deck’s S input jack

(S-IN) to the VCR-1 OUT jack using S jack
connection cords.

• Connect the video deck’s S output jack (S-OUT) to the

VCR-2/V.AUX IN jack and the video deck’s S input
jack (S-IN) to the VCR-2/V.AUX OUT jack using S
jack connection cords.

S-VIDEO

S-VIDEO

S-VIDEO

S-VIDEO

Video deck 2

ENGLISH

9

Connecting the antenna terminals

DIRECTION OF
BROADCASTING
STATION

75 Ω/ohms
COAXIAL
CABLE

FM ANTENNA

FEEDER
CABLE

FM INDOOR
ANTENNA
(Supplied)

FM ANTENNA
ADAPTER
(Supplied)

AM LOOP
ANTENNA
(Supplied)

AM OUTDOOR
ANTENNA

GROUND

• An F-type FM antenna cable plug can be connected directly.

• If the FM antenna cable’s plug is not of the F-type, connect using the included antenna adapter.

AM loop antenna assembly

Connect to the AM
antenna terminals.

Remove the vinyl tie
and take out the
connection line.

Bend in the reverse
direction.

a. With the antenna

on top any stable
surface.

b. With the antenna

attached to a wall.

Mount

Installation hole
Mount on wall, etc.

75 Ω/ohms COAXIAL CABLE

Open the cover

ANTENNA ADAPTER

REMOVE

CLAMP

75 Ω/ohms COAXIAL CABLE

CLAMP

CLAMP

CLAMP

PULL

PULL

SHUT

SHUT

Connection of AM antennas

1. Push the lever. 2. Insert the conductor. 3. Return the lever.

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s
attention to Article 820-40 of the NEC which provides
guidelines for proper grounding and, in particular, specifies
that the cable ground shall be connected to the grounding
system of the building, as close to the point of cable entry
as practical.

Notes:

• Do not connect two FM antennas simultaneously.

• Even if an external AM antenna is used, do not disconnect
the AM loop antenna.

• Make sure AM loop antenna lead terminals do not touch
metal parts of the panel.

IN

IN

OUT

SIGNAL
GND

DVD

EXT. INANTENNA

VDP

TV

/

DBS

VCR-2/
V.AUX

COAXIAL

VCR-2/
V.AUX

CDR/
TAPE

CDR/
TAPE

VCR-1

VCR-1OPT.-1

OPT.-2

OPT.-3

FR

LOOP
ANT.

AM

FM
COAX.
75

SW

SR

CD

PHONO

FL

C

SL

SPEAKER SYSTEMS

AUDIO

DIGITAL

C-VIDEO

MONITOR

S-VIDEO

PRE OUT

R L

R L

R L

R L

R

FR

SURROUND CENTER

SUB

CENTER

WOOFER

9kHz

10kHz

1

4

2

3

14mm

9mm

14mm

19mm

5mm

5mm

5C-2V3C-2V

5C-2V

FM antenna adapter assembly

ENGLISH

10

IN

IN

OUT

SIGNAL
GND

DVD

EXT. INANTENNA

VDP

TV

/

DBS

VCR-2/
V.AUX

COAXIAL

VCR-2/
V.AUX

CDR/
TAPE

CDR/
TAPE

VCR-1

VCR-1OPT.-1

OPT.-2

OPT.-3

FR

LOOP
ANT.

AM

FM
COAX.
75

SW

SR

CD

PHONO

FL

C

SL

SPEAKER SYSTEMS

AUDIO

DIGITAL

C-VIDEO

MONITOR

S-VIDEO

PRE OUT

L

R L

R L

R L

R L

R L

R

B

R

A

FRONT

SURROUND CENTER FRONT FRON

SUB

CENTER

WOOFER

VOLTAGE SE

115V

9kHz

L

R

L

R

Connecting the external input (EXT. IN) jacks

• These input jacks are for inputting multi-channel audio signals in high definition MUSE 3-1 format, multi-channel audio signals from an MPEG
multi-channel decoder, or future multi-channel sound format, etc.

• When making connections, also refer to the operating instructions of the other components.

When connecting a high definition (MUSE 3-1 format)
component, use a separately sold mono/stereo cable if the
surround channel output is monaural.

Front

Surround

Subwoofer

Center

Speaker system connections

• Connect the speaker terminals with the speakers making sure that
like polarities are matched (≈ with ≈ , √ with √ ). Mismatching of
polarities will result in weak central sound, unclear orientation of
the various instruments, and the sense of direction of the stereo
being impaired.

• When making connections, take care that none of the individual
conductors of the speaker cord come in contact with adjacent
terminals, with other speaker cord conductors, or with the rear
panel.

NOTE:
NEVER touch the speaker terminals when the power is on.
Doing so could result in electric shocks.

Speaker Impedance

• Speakers with an impedance of from 6 to 16 Ω/ohms can be

connected for use as surround and center speakers.

• Speakers with an impedance of 6 to 16 Ω/ohms can be connected

for use as front speakers.

• Be careful when using two pairs of front speakers (A + B) at the
same time, since use of speakers with an impedance of less than
8 Ω/ohms will lead to damage.

• The protector circuit may be activated if the set is played for long
periods of time at high volumes when speakers with an impedance
lower than the specified impedance are connected.

Connection the speaker terminals

1. Loosen by turning
counterclockwise

2. Insert the cord. 3. Tighten by turning
clockwise.

Connecting banana plugs

banana plug

Turn clockwise to tighten, then insert the
banana plug.

LINE OUT

Decoders with 6-channel analog
outputs, etc.

ENGLISH

11

IN

IN

OUT

SIGNAL
GND

DVD

EXT. INANTENNA

VDP

TV

/

DBS

VCR-2/
V.AUX

COAXIAL

VCR-2/
V.AUX

CDR/

TAPE

CDR/

TAPE

VCR-1

VCR-1OPT.-1

OPT.-2

OPT.-3

FR

LOOP
ANT.

AM

FM
COAX.
75

SW

SR

CD

PHONO

FL

C

SL

SPEAKER SYSTEMS

AUDIO

DIGITAL

C-VIDEO

MONITOR

S-VIDEO

PRE OUT

L

R L

R L

R L

R L

R L

R

L

R

B

R L

A

FRONT

SURROUND

SURROUND CENTER FRONT FRONT

SUB

CENTER

WOOFER

9kHz

10kHz

(L) (

R

)

(L) (

R

)

(L) (

R

)

Connection jack for
subwoofer with built-in
amplifier (super woofer),
etc.

FRONT SPEAKER

SYSTEMS (B)

CENTER SPEAKER

SYSTEM

SURROUND SPEAKER

SYSTEMS

• Precautions when connecting speakers

If a speaker is placed near a TV or video monitor, the colors on the screen may be disturbed by the speaker’s magnetism. If this should happen, move the speaker
away to a position where it does not have this effect.

Connections

• When making connections, also refer to the operating instructions of the other components.

• This unit is equipped with a high-speed protection circuit. The purpose of this circuit is to protect the speakers under
circumstances such as when the output of the power amplifier is inadvertently short-circuited and a large current flows, when
the temperature surrounding the unit becomes unusually high, or when the unit is used at high output over a long period
which results in an extreme temperature rise.
When the protection circuit is activated, the speaker output is cut off and the power supply indicator LED flashes. Should
this occur, please follow these steps: be sure to switch off the power of this unit, check whether there are any faults with
the wiring of the speaker cables or input cables, and wait for the unit to cool down if it is very hot. Improve the ventilation
condition around the unit and switch the power back on.
If the protection circuit is activated again even though there are no problems with the wiring or the ventilation around the
unit, switch off the power and contact a DENON service center.

Protector circuit

• The protector circuit may be activated if the set is played for long periods of time at high volumes when speakers with an
impedance lower than the specified impedance (for example speakers with an impedance of lower than 4 Ω/ohms) are
connected. If the protector circuit is activated, the speaker output is cut off. Turn off the set’s power, wait for the set to cool
down, improve the ventilation around the set, then turn the power back on.

Note on speaker impedance

FRONT SPEAKER

SYSTEMS (A)

ENGLISH

12

6

PART NAMES AND FUNCTIONS

Front Panel

• For details on the functions of these parts, refer to the pages given in parentheses ( ).

!4

SELECT knob ………………………………………………………(33)

!5

TONE CONTROL button …………………………………………(33)

!6

CH. VOL button ……………………………………………………(36)

!7

MASTER VOLUME control ………………………………………(33)

!8

Master volume indicator (VOLUME LEVEL) ……………………(33)

!9

Display

@0

INPUT indicators .......................................................................(33)

@1

SIGNAL indicator …………………………………………………(33)

@2

Remote control sensor (REMOTE SENSOR) …………………(23)

@3

Power indicator ……………………………………………………(31)

@4

FUNCTION knob …………………………………………………(32)

@5

TUNING PRESET button …………………………………………(47)

@6

SOURCE selector button ………………………………………(32)

@7

REC SELECT button ………………………………………………(35)

q

Power ON/STANDBY switch …………………………………(31)

w

Headphones jack (PHONES) ……………………………………(34)

e

Tape monitor button (CDR/TAPE MON)…………………………(32)

r

Tape monitor indicator ……………………………………………(32)

t

Front speaker system selector buttons (SPEAKER A/B) ..........(31)

y

INPUT MODE button ……………………………………………(32)

u

ANALOG button……………………………………………………(32)

i

EXT. IN button ……………………………………………………(35)

o

VIDEO SELECT button ……………………………………………(34)

!0

DIMMER button……………………………………………………(34)

!1

STATUS button ……………………………………………………(34)

!2

SURROUND MODE button ………………………………………(37)

!3

SURROUND PARAMETER button ………………………………(42)

ENGLISH

13

Remote control unit

• For details on the functions of these parts, refer to the pages given in parentheses ( ).

LEDs (indicators) ..................................(28)

SYSTEM CALL buttons ........................(29)

Input source selector

buttons ..................................................(32)

System buttons ....................................(24)

SPEAKER select button .........................(31)

Surround buttons ................................(24)

INPUT MODE selector

buttons ..................................................(32)

Mode selector switches.........................(27)

Tuner system buttons ...........................(24)

USE/LEARN selector

button ..................................................(28)

Test tone button ....................................(36)

SYSTEM SETUP button .........................(14)

Remote control signal

transmitter ............................................(23)

Power button ......................................(31)

Tuner buttons ......................................(45)

Master volume control

buttons ..................................................(33)

MUTING button......................................(34)

SURROUND PARAMETER

button ..................................................(41)

Channel select/enter

button ..................................................(14)

Cursor buttons ......................................(14)

ON SCREEN button ..............................(34)

DVD SETUP button ..............................(27)

STATUS button.......................................(34)

NOTE

• The shaded buttons do not function with the AVR-2801/981.
(Nothing happens when they are pressed.)
The button indicated , however, can be used with the learning function.

ENGLISH

14

TUNING

BAND

TITLE

MENU/GUIDE

MODE

MEMORY

USE/LEARN T.TONE

RETURN

DVD

SET UP

STATUS

DISPLAY

ON SCREEN

MUTING

AVR/AVC VIDEO DVD TV

AUDIO

VDP VCR

CD

CDR/MDDECK

SYSTEM

SETUP

SURROUND

PARAMETER

CH SELECT

SELECT

ENTER

7

SETTING UP THE SYSTEM

• Once all connections with other AV components have been completed as described in “CONNECTIONS” (see pages 6 to 11), make the various
settings described below on the monitor screen using the AVR-2801/981’s on-screen display function.
These settings are required to set up the listening room’s AV system centered around the AVR-2801/981.

• Use the following buttons to set up the system:

SYSTEM SETUP button

Press this to display the system setup menu.

SURROUND PARAMETER button

Press this to display the surround parameter menu.

ENTER button

Press this to switch the display on the screen.
Also use this button to complete the setting on the screen.

CURSOR buttons

and : Use these to move the cursors (

0 and 1) to the left and right

on the screen.

and : Use these to move the cursors (• and ª) up and down on the

screen.

• System setup items and default values (set upon shipment from the factory)

System setup Default settings

q

w

e

r

t

y

Speaker
Configuration

Subwoofer mode

Delay Time

Channel
Level

Digital In
Adjutment

On Screen
Display

Auto Tuner
Presets

Input the combination of speakers in your system and their
corresponding sizes (SMALL for regular speakers, LARGE for full-size,
full-range) to automatically set the composition of the signals output
from the speakers and the frequency response.

This selects the subwoofer speaker for playing deep bass signals.

This parameter is for optimizing the timing with which the audio
signals are produced from the speakers and subwoofer according to
the listening position.

This adjusts the volume of the signals output from the speakers and
subwoofer for the different channels in order to obtain optimum
effects.

This assigns the digital input jacks for the different input
sources.

This sets whether or not to display the on-screen display that appears
on the monitor screen when the controls on the remote control unit or
main unit are operated (from MONITOR outputs only).

FM stations are received automatically and stored in the memory.

Input

source
Digital

Inputs

Front Sp. Center Sp. Surround Sp. Subwoofer

Small

Center

3.6 m (12 ft)

Surround L & R —

3.0 m (10 ft) —

Small YesLarge

LFE

Front & Subwoofer

3.6 m (12 ft)

Front L

0 dB

CD

COAXIAL

On Screen Display = ON

A1 ~ A8

B1 ~ B8

C1 ~ C8

D1 ~ D8

E1 ~ E8

87.5/89.1/98.1/107.9/90.1/90.1/90.1/90.1 MHz

520/600/1000/1400/1500/1710 kHz/90.1/90.1 MHz

90.1 MHz

90.1 MHz

90.1 MHz

Front R

0 dB

DVD

OPTICAL 1

Subwoofer

0 dB

VDP

OPTICAL 2

TV/DBS

OPTICAL 3

VCR-1

OFF

VCR-2/
V. AUX

——

OFF — —

Center

0 dB

Surround L

0 dB

Surround R — —

0 dB — —

NOTES:

• The on-screen display signals are output with priority to the S-VIDEO MONITOR OUT jack during playback of a video component. For example,
if the TV monitor is connected to both the AVR-2801/981’s S-Video and video monitor output jacks and signals are input to the AVR-2801/981
from a video source (VDP, etc.) connected to both the S-Video and video input jacks, the on-screen display signals are output with priority to
the S-Video monitor output. If you wish to output the signals to the video monitor output jack, do not connect a cord to the S-VIDEO
MONITOR OUT jack. (For details, see page 22.)

• The AVR-2801/981’s on-screen display function is designed for use with high resolution monitor TVs, so it may be difficult to read small
characters on TVs with small screens or low resolutions.

• The setup menu is not displayed when “HEADPHONE ONLY” is selected.

ENGLISH

15

Speaker system layout

Basic system layout

• The following is an example of the basic layout for a system consisting of six speaker systems and a television monitor:

Subwoofer

Center speaker system

Front speaker systems
Set these at the sides of the TV or screen with
their front surfaces as flush with the front of the
screen as possible.

Surround speaker systems

Before setting up the system

1

2

Check that all the connections are correct, then turn on the main unit’s power.

TITLE

SYSTEM

SETUP

Display the System Setup Menu.

Setting the type of speakers

• The composition of the signals output from the different channels and the frequency response are adjusted automatically according to the
combination of speakers actually being used.

1

2

ENTER

At the System Setup Menu select “Speaker Configuration”.

Switch to the speaker configuration screen.

ENGLISH

16

3

Set whether or not speakers are connected and, if so, their size
parameters.

• To select the speaker

• To select the parameter

Center Sp.

Front Sp.

Subwoofer

Surround Sp.

4

ENTER

Enter the setting.
When “Front” is set to “Large” and “Subwoofer” is set to “Yes” the set switches to the subwoofer mode.

NOTE:

• Select “Large” or “Small” not according to the actual size of the speaker but according to the speaker’s capacity for playing low frequency
(approximately 80 Hz and below) signals. If you do not know, try comparing the sound at both settings (setting the volume to a level low
enough so as not to damage the speakers) to determine the proper setting.

• Parameters

Large…… Select this when using speakers that can fully reproduce low sounds of below 80 Hz.
Small…… Select this when using speakers that cannot reproduce low sounds of below 80 Hz with sufficient volume.

When this setting is selected, low frequencies of below 80 Hz are assigned to the subwoofer.
None…… Select this when no speakers are installed.
Yes/No…. Select “Yes” when a subwoofer is installed, “No” when a subwoofer is not installed.

*

If the subwoofer has sufficient low frequency playback capacity, good sound can be achieved even when “Small” is set for the front, center
and surround speakers.

*

For the majority of speaker system configurations, using the SMALL setting for all five main speakers and Subwooofer On with a connected
subwoofer will yield the best results.

Setting the subwoofer mode

1

Select the bass signal playback mode.

2

ENTER

Enter the setting.
The System Setup Menu reappears.

ENGLISH

17

L1

L2

L3

Setting the delay time

Input the distances from the listening position to the speakers and set the surround delay time.

Preparations:

Measure the distances from the listening position to the speakers (L1 to L3 on the diagram at the right).

L1: Distance from center speakers to listening position
L2: Distance from front speakers to listening position
L3: Distance from rear speakers to listening position

1

At the System Setup Menu select “Delay Time”.

FL

Center

FR

Listening
position

SL

SR

2

ENTER

Switch to the Delay Time screen.

NOTES:

• In the Subwoofer mode screen, you have the flexibility to choose how bass information is distributed to your speakers if you have large front
left and right speakers and a subwoofer as part of your home theater speaker system.

• By selecting the “LFE + Main” option, you will be sending the same bass frequencies to both the front left, front right, and the subwoofer
speakers simultaneously. Depending upon your room size and shape, this can create a more evenly distributed bass around the room or
sometimes actually decrease the amount of bass in the room due to low frequency cancellations.

• If the “LFE” option is selected, bass from the large front left and front right speakers goes only to the front left and front right speakers. Bass
going to the subwoofer comes from the LFE signal and any speakers which you have designated as “Small.” This selection is preferred as
it reduces the chances of bass cancellations in the room.

• Once you have positioned all of your speakers in the room, choose the option which gives you the most solid sounding bass.

• When the subwoofer is set to “Yes”, bass sound is output from the subwoofer regardless of the subwoofer mode setting in surround modes
other than Dolby/DTS.

NOTES:

• Set the center speaker so that the distance to the front speakers (left and right) or the subwoofer
is the same (L2 = L1) or so that the difference in the distance (L2 – L1) is 5 feet (1.5 meters) or less.

• Set the surround speakers (left and right) so that the distance to the front speakers (left and right)
or the subwoofer is the same (L2 = L3) or so that the difference in the distance (L2 – L3) is 15 feet
(4.5 meters) or less.

3

Select the desired unit, meters or feet.
Select (darken) the desired units, “Meters” or “Feet”.

Example: When “Feet” is selected

ENGLISH

18

4

5

6

Once “Meters” or “Feet” is selected in step 3, the Delay Time screen appears automatically.

Select the speaker to be set.

Set the distance between the center speaker and listening position.
The distance changes in units of 1 foot (0.1 meters) each time the button
is pressed. Select the value closest to the measured distance.

*

If “Yes” is selected for “Default”, the settings are automatically reset to
the default values.

*

If you set an invalid distance, a CAUTION notice, such as screen right
will appear. In this case, please relocate the blinking speaker(s) so that
its distance is no larger than the value shown in highlighted line.

*

Set in such a way that the distance to the center speaker is the same as
or up to 5 feet (1.5 meters) shorter than the distance to the front
speakers and the subwoofer.

*

Set in such a way that the distance to the surround speakers is the same
as or up to 15 feet (4.5 meters) shorter than the distance to the front
speakers and the subwoofer.

Example: When the distance is set to 12

feet for the center speaker (L1)

7

ENTER

Enter the setting.
The System Setup Menu reappears.
The AVR-2801/981 automatically sets the optimum surround delay time for the listening room.

NOTE:

• If the distance unit is changed after the delay time is set, the settings are reset to the factory default values (see page 14).

ENGLISH

19

1

2

3

4

ENTER

At the System Setup Menu select “Channel Level”.

Switch to the Channel Level screen.

Select “Test Tone Mode”.

Select the mode.
Select “Auto” or “Manual”.

• Auto:
Adjust the level while listening to the test tones produced automatically
from the different speakers.

• Manual:
Select the speaker from which you want to produce the test tone to
adjust the level.

Example: When the “Auto” mode is selected

5

6

Select “Test Tone Start”.

Select “Yes”.

Setting the channel level

• Use this setting to adjust so that the playback level between the different channels is equal.

• From the listening position, listen to the test tones produced from the speakers to adjust the level.

• The level can also be adjusted directly from the remote control unit. (For details, see page 36.)

ENGLISH

20

7

a. If the “Auto” mode is selected:

Test tones are automatically emitted from the different speakers.
The test tones are emitted from the different speakers in the following
order, at 4-second intervals the first time and second time around, 2­second intervals the third time around and on:

b. When the “Manual” mode is selected

Use the and cursor buttons to select the speaker from which you
want to produce the test tone, then use the and cursor buttons
to adjust so that the volume from the different speakers sounds the
same.

Use the CURSOR buttons to adjust all the speakers to the same
volume.
The volume can be adjusted between –12 dB and +12 dB in units of 1
dB.

1

FL

1

C

1

SW

1

FR

1

SR

1

SL

Example: When the volume is set to –12 dB

while the test tone is being
produced from the subwoofer

Example: When the volume is set to –12 dB

while the subwoofer is selected

Flashing

Flashing

8

ENTER

After the above settings are completed, press the ENTER button.
The “Channel Level” screen reappears.
Press the ENTER button again, the “System Setup Menu” screen reappears.

*

To cancel the settings, select “Level Clear” and “Yes” on the “Channel Level” screen, then make the settings again.

The level of each channel should be adjusted to 75 dB (C-weighted, slow meter mode) on a sound level meter at the listening position.
If a sound level meter is not available adjust the channels by ear so the sound levels are the same. Because adjusting the subwoofer level test
tone by ear is difficult, use a well known music selection and adjust for natural balance.
NOTE: When adjusting the level of an active subwoofer system, you may also need to adjust the subwoofer’s own volume control.

*

When you adjust the channel levels while in the SYSTEM SETUP CHANNEL LEVEL mode, the channel level adjustments made will affect
ALL surround modes. Consider this mode a Master Channel Level adjustment mode.

*

After you have completed the SYSTEM SETUP CHANNEL LEVEL adjustments, you can then activate the individual surround modes and
adjust channel levels that will be remembered for each of those modes. Then, whenever you activate a particular surround sound mode, your
preferred channel level adjustments for just that mode will be recalled. Check the instructions for adjusting channel levels within each
surround mode on Page 36.

*

You can adjust the channel levels for each of the following surround modes: DIRECT, STEREO, 5CH STEREO, DOLBY/DTS SURROUND,
ROCK ARENA, JAZZ CLUB, VIDEO GAME, MONO MOVIE, and MATRIX.

Setting the digital in assignment

• This setting assigns the digital input jacks of the AVR-2801/981 for the different input sources.

1

At the System Setup Menu select “Digital In Assignment”.

ENGLISH

21

3

4

ENTER

Select the digital input jack to be assigned to the input source.

• To select the input source

• To select the digital input jack
Select “OFF” for input sources for which no digital input jacks are used.

*

If “Yes” is selected for “Default”, the settings are automatically reset to the default values.

Enter the setting.
The System Setup Menu reappears.

NOTE:

• “PHONO”, “CDR/TAPE” and “TUNER” cannot be selected on the Digital Inputs screen.

Setting the on-screen display (OSD)

• Use this to turn the on-screen display (messages other than the menu screens) on or off.

1

At the System Setup Menu select “On Screen Display”.

2

ENTER

Switch to the Digital In Assignment screen.

2

3

4

ENTER

ENTER

Switch to the On Screen Display screen.

Select “ON” or “OFF”.

Enter the setting.
The System Setup Menu reappears.

ENGLISH

22

Auto tuner presets

Use this to automatically search for FM broadcasts and store up to 40 stations at preset channels A1 to 8, B1 to 8, C1 to 8, D1 to 8 and E1 to 8.

NOTE:

• If an FM station cannot be preset automatically due to poor reception, use the “Manual tuning” operation to tune in the station, then preset it
using the manual “Preset memory” operation.

1

Use the CURSOR buttons to specify “Auto Tuner Presets” from the
“System Setup Menu” screen.

ENTER

2

3

Press the ENTER button.
The “Auto Preset Memory” screen appears.

Use the CURSOR button to select “Yes”.
“Search” flashes on the screen and searching begins.
“Completed” appears once searching is completed.
The display automatically switches to screen.

*

This completes system setup. Once these settings are made, there is no need to change them unless different AV components are connected
or the speakers are repositioned.

After completing system setup

This button can be pressed at any time during the system setup process to complete the process.

TITLE

SYSTEM

SETUP

1

At the System Setup Menu, press the SYSTEM SETUP button.

*

The changed settings are entered and the on-screen display turns off.

• On-screen display signals

Signals input to the AVR-2801/981

VIDEO signal input jack (yellow)

E

C

E

C

1

2

3

4

S-video signal input jack

E

E

C

C

VIDEO MONITOR OUT video

signal output jack (yellow)

C

C

E

E

S-video MONITOR OUT video

signal output jack

C

E

C

C

On-screen display signal output

(C: Signal E: No signal)

NOTE:

• For 4 above, the on-screen display signals are output to the VIDEO MONITOR OUT video signal output jack (yellow) if the monitor TV is not
connected to the S-video MONITOR OUT video signal output jack.

(C: On-screen signals output E: On-screen signals not output)

ENGLISH

23

8

REMOTE CONTROL UNIT

• The included remote control unit (RC-881) can be used to operate not only the AVR-2801/981 but other remote control compatible DENON
components as well. Furthermore, it is equipped with a function for learning the control signals of remote control units of other manufacturers,
so it can also be used to operate non-DENON remote control compatible video components.

Inserting the batteries

q Remove the remote control unit’s rear cover.

w Set two R6P/AA batteries in the battery compartment in the

indicated direction.

e Put the rear cover back on.

Notes on Batteries

• Use R6P/AA batteries in the remote control unit.

• The batteries should be replaced with new ones approximately
once a year, though this depends on the frequency of usage.

• Even if less than a year has passed, replace the batteries with new
ones if the set does not operate even when the remote control unit
is operated nearby the set.

• When inserting the batteries, be sure to do so in the proper
direction, following the “≈” and “√” marks in the battery
compartment.

• To prevent damage or leakage of battery fluid:

• Do not use a new battery together with an old one.

• Do not use two different types of batteries.

• Do not short-circuit, disassemble, heat or dispose of batteries in

flames.

• Remove the batteries from the remote control unit when you do
not plan to use it for an extended period of time.

• If the battery fluid should leak, carefully wipe the fluid off the inside
of the battery compartment and insert new batteries.

• When replacing the batteries, have the new batteries ready and
insert them as quickly as possible.

• The learned remote control signals may be cleared if no batteries
are in the remote control unit for about 5 seconds.
The factory-installed codes are in permanent memory, however.

Using the remote control unit

Approx. 7 m/22 feet

• Point the remote control unit at the remote sensor on the main unit
as shown on the diagram.

• The remote control unit can be used from a straight distance of
approximately 7 meters/22 feet from the main unit, but this
distance will be shorter if there are obstacles in the way or if the
remote control unit is not pointed directly at the remote sensor.

• The remote control unit can be operated at a horizontal angle of up
to 30 degrees with respect to the remote sensor.

NOTES:

• It may be difficult to operate the remote control unit if the remote
sensor is exposed to direct sunlight or strong artificial light.

• Do not press buttons on the main unit and remote control unit
simultaneously. Doing so may result in malfunction.

• Neon signs or other devices emitting pulse-type noise nearby may
result in malfunction, so keep the set as far away from such
devices as possible.

30°

30°

ENGLISH

24

Operating DENON audio components

• Turn on the power of the different components before operating them.

1

2

3

Set mode switch 1 to “AUDIO (AVR/AVC)”.

Set mode switch 2 to the position for the component to be
operated.

Operate the audio component.

• For details, refer to the component’s operating instructions.

*

While this remote control is compatible with a wide range of infrared controlled components, some models of components may not be
operated with this remote control.

1. CD player (CD) and CD recorder and MD recorder (CDR/MD)
system buttons

3. Tuner system buttons

*

For the tuner only, the following buttons can also be operated:

2. Tape deck (DECK) system buttons

AVR/AVC VIDEO

AUDIO
DVD TV

VDP VCR

CD

CDR/MDDECK

DVD

START LEARNED/TX

SPEAKER

TUNING

BAND

TITLE

MENU/GUIDE

MODE

MEMORY

USE/LEARN T.TONE DVD

SET UP

RETURN

STATUS

DISPLAY

ON SCREEN

DOLBY / DTS

SURROUND

DIRECT

DSP SIMULATION

5CH STEREO STEREO

INPUT MODE

ANALOG EXT.IN

MUTING

MASTER VOL.

VOLUME DISC SKIP+

SYSTEM CALL POWER

VDP TUNER SHIFT

TV/DBS PHONO

VCR-1 CD CHANNEL

VCR-2/V.AUX

TV/VCR

AVR/AVC VIDEO DVD TV

AUDIO

VDP VCR

CD

CDR/MDDECK

SYSTEM

SETUP

SURROUND

PARAMETER

CH SELECT

SELECT

RC-881

123
4

SET

A / B

CALL OFF

ENTER

ON / SOURCE

56

789

+10

0

3

2

1

3

CDR / TAPE

VOLUME DISC SKIP+

VCR-2/V.AUX

TV/VCR

A / B

+10

DVD

SYSTEM CALL POWER

VDP TUNER SHIFT

TV/DBS PHONO

VCR-1 CD CHANNEL

123
4

SET CALL OFF

ON / SOURCE

56

789

CDR / TAPE

TUNING

BAND

TITLE

MENU/GUIDE

MODE

MEMORY

RETURN

STATUS

DISPLAY

ON SCREEN

SYSTEM

SETUP

SURROUND
PARAMETER

CH SELECT

SELECT

ENTER

VOLUME DISC SKIP+

VCR-2/V.AUX

TV/VCR

A / B

+10

6, 7 : Manual search (forward and reverse)

2 : Stop
1 :Play

8, 9 : Auto search (cue)

3 : Pause

DISC : Switch discs

SKIP+ (for CD changers only)

SHIFT : Switch preset channel range

CHANNEL : Preset channel

+, – up/down

TUNING : Frequency

•, ª up/down

BAND : Switch between the AM and FM bands

MODE : Switch between auto and mono

MEMORY : Preset memory

6 : Rewind
7 : Fast-forward

2 : Stop
1 : Forward play
3 : Pause
0 : Reverse play

A/B : Switch between decks A and B

ENGLISH

25

Preset memory (Audio component)

• DENON components can be operated by setting the preset memory for CDR or MD. Operation is not possible for some models, however.
In this case use the learning function (see page 28) to store the remote control signals.

• For instructions on clearing the presettings stored in the preset memory, see page 31.

1

2

Set the slide switch to “AUDIO”.

Set the slide switch to “CDR/MD.

The LEARNED/TX LED flashes.

Keep the POWER button pressed in
when performing steps 3 and 4

()

AVR/AVC VIDEO

AUDIO
DVD TV

VDP VCR

CD

CDR/MDDECK

3

Holding in the POWER button, press the
button for the components you want to
set.

DVD

START LEARNED/TX

SPEAKER

DOLBY / DTS
SURROUND

DIRECT

DSP SIMULATION

5CH STEREO STEREO

INPUT MODE

ANALOG EXT.IN

MUTING

MASTER VOL.

VOLUME DISC SKIP+

SYSTEM CALL POWER

VDP TUNER SHIFT

TV/DBS PHONO

VCR-1 CD CHANNEL

VCR-2/V.AUX

TV/VCR

AVR/AVC VIDEO DVD TV

AUDIO

VDP VCR

CD

CDR/MDDECK

SYSTEM

SURROUND

RC-881

123
4

SET

A / B

CALL OFF

ON / SOURCE

56

789

+10

0

3

3

2

1

CDR / TAPE

“CDR/MD”

(DIRECT) (STEREO) (EXT. IN)

DIRECT

STEREO

EXT.IN

DENON CDR A DENON CDR B DENON MD(POWER)

ON / SOURCE

Combinations of Personal System Codes

Preset memory (Video component)

• DENON and other makes of components can be operated by setting the preset memory for your make of video component. Operation is not
possible for some models, however. In this case use the learning function (see page 28) to store the remote control signals.

• For instructions on clearing the presettings stored in the preset memory, see page 31.

1

2

3

Set the slide switch to “VIDEO”.

Set the slide switch to the component to
be registered (DVD, VDP, VCR or TV).

Holding in the POWER button, press the
button for the corresponding manufacturer
in block A.
(Refer to Table 1.)

The LEARNED/TX LED flashes.

Keep the POWER button pressed in
when performing steps 3 and 4

()

AVR/AVC VIDEO

AUDIO
DVD TV

VDP VCR

CD

CDR/MDDECK

Flashes

4

5

Next, while holding the POWER button,
press the button for the code in block B.
(Refer to Table 1.) The operation is
completed when the button is released and
the LEARNED/TX LED lights.

To continue registering other components,
repeat steps 2 to 4.

DVD

START LEARNED/TX

SPEAKER

TUNING

BAND

TITLE

MENU/GUIDE

MODE

MEMORY

USE/LEARN T.TONE DVD

SET UP

RETURN

STATUS

DISPLAY

ON SCREEN

DOLBY / DTS

SURROUND

DIRECT

DSP SIMULATION

5CH STEREO STEREO

INPUT MODE

ANALOG EXT.IN

MUTING

MASTER VOL.

VOLUME DISC SKIP+

SYSTEM CALL POWER

VDP TUNER SHIFT

TV/DBS PHONO

VCR-1 CD CHANNEL

VCR-2/V.AUX

TV/VCR

AVR/AVC VIDEO DVD TV

AUDIO

VDP VCR

CD

CDR/MDDECK

SYSTEM

SETUP

SURROUND
PARAMETER

CH SELECT

SELECT

RC-881

123
4

SET

A / B

CALL OFF

ENTER

ON / SOURCE

56

789

+10

0

3

3,4

4

2

1

CDR / TAPE

• This remote control unit can be used to operate components of other manufacturers without using the learning function by registering the
manufacturer of the component as shown on Table 1.

*

Preset codes set upon shipment from the factory.

ENGLISH

26

HITACHI A

——

“VCR”

(DIRECT)

MITSUBISHI A

PANASONIC A

JVC (VICTOR) A

SONY A

PIONEER

TOSHIBA A

SANYO A

SHARP A

NEC A

PHILIPS A

RCA A

GENERAL
ELECTRIC A

NAGNAVOX A

(STEREO)

—

HITACHI B

MITSUBISHI B

PANASONIC B

JVC (VICTOR) B

SONY B

—

TOSHIBA B

SANYO B

SHARP B

NEC B

PHILIPS B

RCA B

GENERAL
ELECTRIC B

NAGNAVOX B

(EXT. IN)

—

—

MITSUBISHI C

PANASONIC C

JVC (VICTOR) C

SONY C

—

—

—

—

NEC C

PHILIPS C

—

—

NAGNAVOX C

B

A

q (DVD)

w (VDP)

e (TUNER)

r (TV/DBS)

t

y (PHONO)

u (VCR-1)

i (CD)

o (CDR/TAPE)

p

(SHIFT)

(CHANNEL +)

(CHANNEL –)

(A/B)

(VCR/V.AUX)

DIRECT

STEREO

EXT.IN

SHIFT

CHANNEL

+

CHANNEL

–

*

Preset codes set upon shipment from the factory.

“TV”

(DIRECT)

DENON/HITACHI

MITSUBISHI A

PANASONIC A

JVC (VICTOR)

SONY

PIONEER

TOSHIBA

SANYO

SHARP

NEC

PHILIPS A

RCA A

GENERAL
ELECTRIC A

NAGNAVOX A

(STEREO)

—

—

MITSUBISHI B

PANASONIC B

—

—

—

—

—

—

—

—

—

GENERAL
ELECTRIC B

—

(EXT. IN)

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

B

A

q (DVD)

w (VDP)

e (TUNER)

r (TV/DBS)

t

y (PHONO)

u (VCR-1)

i (CD)

o (CDR/TAPE)

p

(SHIFT)

(CHANNEL +)

(CHANNEL –)

(A/B)

(VCR/V.AUX)

DIRECT

STEREO

EXT.IN

SHIFT

CHANNEL

+

CHANNEL

–

NOTES:

• The signals for the pressed buttons are emitted while setting the preset memory. To avoid accidental operation, cover the remote control
unit’s transmitting window while setting the preset memory.

• Some models and years of manufacture of components of the manufacturers listed on Table 1 cannot be used.

• The signals stored at “learned” buttons have priority over the preset codes. If you wish to clear the “learned” signals, do so as described on
page 31.

• Some manufacturers use different types of remote control codes for their products. If the component does not operate when set to remote
codeset A, try setting to the B or C codesets.

DENON A

Table 1: Combinations of Personal System Codes for Different Manufacturers

“DVD”

(DIRECT)

—

—

PANASONIC

—

SONY

PIONEER

TOSHIBA

—

—

—

—

—

—

—

(STEREO)

DENON B

—

—

—

—

—

—

—

—

—

—

—

—

—

—

(EXT. IN)

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

B

A

q (DVD)

w (VDP)

e (TUNER)

r (TV/DBS)

t

y (PHONO)

u (VCR-1)

i (CD)

o (CDR/TAPE)

p

(SHIFT)

(CHANNEL +)

(CHANNEL –)

(A/B)

(VCR/V.AUX)

DIRECT

STEREO

EXT.IN

SHIFT

CHANNEL

+

CHANNEL

–

“VDP”

(DIRECT)

DENON A

—

MITSUBISHI

PANASONIC

—

SONY A

PIONEER

—

—

—

—

PHILIPS

RCA

—

NAGNAVOX

(STEREO)

DENON B

—

—

—

—

SONY B

—

—

—

—

—

—

—

—

—

(EXT. IN)

DENON C

—

—

—

—

SONY C

—

—

—

—

—

—

—

—

—

B

A

q (DVD)

w (VDP)

e (TUNER)

r (TV/DBS)

t

y (PHONO)

u (VCR-1)

i (CD)

o (CDR/TAPE)

p

(SHIFT)

(CHANNEL +)

(CHANNEL –)

(A/B)

(VCR/V.AUX)

DIRECT

STEREO

EXT.IN

SHIFT

CHANNEL

+

CHANNEL

–

ENGLISH

27

Operating a video component stored in the preset memory

1

Set the slide switch to “VIDEO”.

AVR/AVC VIDEO

AUDIO

2

Set the slide switch to the component to be registered (DVD,
VDP, VCR or TV).

DVD TV

VDP VCR

CD

CDR/MDDECK

DVD

START LEARNED/TX

SPEAKER

TUNING

BAND

TITLE

MENU/GUIDE

MODE

MEMORY

USE/LEARN T.TONE DVD

SET UP

RETURN

STATUS

DISPLAY

ON SCREEN

DOLBY / DTS

SURROUND

DIRECT

DSP SIMULATION

5CH STEREO STEREO

INPUT MODE

ANALOG EXT.IN

MUTING

MASTER VOL.

VOLUME DISC SKIP+

SYSTEM CALL POWER

VDP TUNER SHIFT

TV/DBS PHONO

CDR/TAPE

VCR-1 CD CHANNEL

VCR-2/V.AUX

TV/VCR

AVR/AVC VIDEO DVD TV

AUDIO

VDP VCR

CD

CDR/MDDECK

SYSTEM

SETUP

SURROUND

PARAMETER

CH SELECT

SELECT

RC-881

123
4

SET

A / B

CALL OFF

ENTER

ON / SOURCE

56

789

+10

0

3

3

2

3

1

3

3

Operate the video component.

• For details, refer to the component’s operating instructions.

*

Some models cannot be operated with this remote control unit.

DVD

SPEAKER

TUNING

BAND

TITLE

MENU/GUIDE

MODE

MEMORY

USE/LEARN T.TONE DVD

SET UP

RETURN

STATUS

DISPLAY

ON SCREEN

DOLBY / DTS

SURROUND

DIRECT

DSP SIMULATION

5CH STEREO STEREO

INPUT MODE

ANALOG EXT.IN

MUTING

MASTER VOL.

VOLUME DISC SKIP+

SYSTEM CALL POWER

VDP TUNER SHIFT

TV/DBS PHONO

VCR-1 CD CHANNEL

VCR-2/V.AUX

TV/VCR

AVR/AVC VIDEO DVD TV

AUDIO

VDP VCR

CD

CDR/MDDECK

SYSTEM

SETUP

SURROUND

PARAMETER

CH SELECT

SELECT

123
4

SET

A / B

CALL OFF

ENTER

ON / SOURCE

56

789

+10

0

CDR / TAPE

1. DVD player system buttons

POWER : Turns power on and off

(ON/SOURCE)

6,7 : Manual search (forward and reverse)

2 : Stop
1 :Play

8,9 : Auto search (cue)

3 : Pause

SKIP + : (for DVD changers only)
TITLE : Call out title

MENU : Call out menu

DISPLAY : Switch display

DVD SET UP

: DVD setup

RETURN : Menu return

•,ª : Cursor up/down

0,1 : Cursor left/right

SELECT : Enter setting

NOTE:

Some manufacturers use different names for the DVD remote control buttons, so also refer to the instructions on
remote control for that component.

2. Video disc player (VDP) system
buttons

3. Video deck (VCR) system
buttons

4. Monitor TV system buttons

POWER : Power on/off

(ON/SOURCE)

6,7 : Manual search

(forward and reverse)

2 : Stop
1 :Play

8,9 : Auto search (cue)

3 : Pause

DVD

VOLUME DISC SKIP+

SYSTEM CALL POWER

VDP TUNER SHIFT

TV/DBS PHONO

VCR-1 CD CHANNEL

VCR-2/V.AUX

TV/VCR

123
4

SET

A / B

CALL OFF

ON / SOURCE

56

789

+10

0

CDR / TAPE

POWER : Power on/off

(ON/SOURCE)

6,7 : Manual search

(forward and reverse)

2 : Stop
1 :Play
3 : Pause

CHANNEL : Switch channel

+, –

DVD

VOLUME DISC SKIP+

SYSTEM CALL POWER

VDP TUNER SHIFT

TV/DBS PHONO

VCR-1 CD CHANNEL

VCR-2/V.AUX

TV/VCR

123
4

SET

A / B

CALL OFF

ON / SOURCE

56

789

+10

0

CDR / TAPE

POWER : Power on/off

(ON/SOURCE)

VOLUME : Volume

•,ª up/down

TV/VCR : Switch between TV

and VCR

CHANNEL : Switch channel

+, –

DVD

VOLUME DISC SKIP+

SYSTEM CALL POWER

VDP TUNER SHIFT

TV/DBS PHONO

VCR-1 CD CHANNEL

VCR-2/V.AUX

TV/VCR

123
4

SET

A / B

CALL OFF

ON / SOURCE

56

789

+10

0

CDR / TAPE

ENGLISH

28

Learning function

• If your AV component is not a DENON product or it cannot be operated with the preset memory codesets, you can “teach” the AVR-2801/981’s
remote control to “learn” the codes from the component’s original remote control.

• The buttons that can be “learned” are the CD, DECK and CDR/MD system buttons (see page 24) and the DVD, VDP, VCR and TV system
buttons (see page 27). (For the CD, CDR/MD, DVD, VDP and TV, the A block buttons can also be “learned”, and for the DVD and TV, the B block
buttons can also be “learned”.)

1

Press the USE/LEARN selector button with the tip of a pen
etc., to set the learn mode. Both the START and LEARNED/TX
indicators flash.

This unit’s remote
control unit

Flashes

2

Set the program switch to the side to be learned.
Set to the AUDIO side for the CD, tape deck or CDR/MD
position, to the VIDEO side for the DVD, VDP, VCR or TV
position.

AVR/AVC VIDEO

AUDIO

3

Set the program switch to the position to be learned.

4

Set the remote control units so they are facing each other,
then press the button to be learned on this unit’s remote
control unit.

The indicator stops flashing and the START LED lights.
The learnable buttons are the buttons which can be operated
with the DENON system codes for the CD player, tape deck,
CD recorder, MD recorder, the buttons which can be operated
with the preset memory for the DVD, VCR, VDP and TV. For
the TV only, however, the buttons in the section indicated “A”
on the diagram above can also be “learned”. Use these to
“learn” TV channels.

DVD TV

VDP VCR

CD

CDR/MDDECK

This unit’s remote
control unit

Transmitting windows

Other remote
control unit

Approx.
5 cm

DVD

SPEAKER

TUNING

BAND

TITLE

MENU/GUIDE

MODE

MEMORY

USE/LEARN T.TONE DVD

SET UP

RETURN

STATUS

DISPLAY

ON SCREEN

DOLBY / DTS

SURROUND

DIRECT

DSP SIMULATION

5CH STEREO STEREO

INPUT MODE

ANALOG EXT.IN

MUTING

MASTER VOL.

VOLUME DISC SKIP+

SYSTEM CALL POWER

VDP TUNER SHIFT

TV/DBS PHONO

VCR-1 CD CHANNEL

VCR-2/V.AUX

TV/VCR

AVR/AVC VIDEO DVD TV

AUDIO

VDP VCR

CD

CDR/MDDECK

SYSTEM
SETUP

SURROUND

PARAMETER

CH SELECT

SELECT

123
4

SET

A / B

CALL OFF

ENTER

ON / SOURCE

56

789

+10

0

A

2

4

3

B

1,8

CDR / TAPE

5

Check that the START LED is lit, then press the button to be
“learned” on the other remote control unit.

6

Once the START LED turns off and the LEARNED/TX LED
lights, release the button on the other remote control unit.

7

To “learn” other buttons, repeat steps 2 to 6.

8

Once the learning operation is completed, press the
USE/LEARN selector button again.
The two LEDs stop flashing and the learning mode is
cancelled.

This unit’s remote
control unit

Other remote
control unit

The two LEDs start
flashing again.

Light

Light

NOTES:

• Up to 26 codes can be “learned”, but this number may be lower if the codes are long.

• If a non-learnable button is pressed or two or more buttons are pressed at once, the two LEDs will once again light when the button(s)
is released.

• If the codes could not be stored, the LEARNED/TX LED does not light after the START LED turns off. For limited number of models, codes
cannot be stored in RC-881.

• If the two LEDs start flashing rapidly after the START LED lights, this means that the memory is already full, and the code you have just
attempted to store was not stored.
To “learn” that code, first perform the resetting operation. (See page 31.)

Check that the stored
codes work properly.

ENGLISH

29

System call function

• The included remote control unit is equipped with a system call function for transmitting multiple remote control signals when a single button
is pressed (this is often referred to as a “macro” function).
This function can be used to turn on the amplifier’s power, select the input source, turn on the monitor TV’s power, turn on a source
component’s power and start playback, etc., all at the touch of a button.

(1) System call buttons

The buttons that can be used for the system call function are shown on the table below.
A series of up to 10 operations can be performed with the POWER ON and OFF buttons, and a series of up to 5 operations can be performed
with other buttons.
System call signals are already preset at the buttons indicated in the shaded section. System call signals can also be stored at any button on
the remote control unit, including the buttons in this section. (See page 30.)

Button

No.

transmissions

Stored

operation 1

Receiver

power on

Receiver

power on

Receiver

power on

Receiver

power on

Receiver

power on

Stored

operation 2

DVD player

(DVD)

power on

LD player

(VDP)

power on

TV power on

Video (VCR)

power on

Receiver

input source

switched to

CD

Stored

operation 3

Receiver
input source
switched to

DVD

Receiver
input source
switched to

VDP

Receiver
input source
switched to

TV/DBS

Receiver
input source
switched to

VCR-1

Stored

operation 4

TV power on

TV power on

TV power on

Stored

operation 5

Stored

operation 6

Stored

operation 7

Stored

operation 8

Stored

operation 9

Stored

operation 10

DVD player

(DVD)

playback

LD player

(VDP)

playback

Video (VCR)

playback

POWER OFF 10

POWER ON 10

DVD 5

VDP

TV/DBS

VCR-1

CD

5

5

5

5

The system call signals for the POWER OFF and
POWER ON buttons are transmitted from the
remote control unit approximately once every
second.
The signals for the other buttons (DVD, VDP, TV /
DBS, VCR-1 and CD) are transmitted approximately
once every 1.5 seconds.

(2) Using the system call function

1

Press the system call button.

• The LEARNED/TX LED flashes for 5 seconds.

CALL

2

Press the button at which the desired system call signals are
stored while the LEARNED/TX LED is flashing.

• The preset signals or the signals you have stored at that
button are transmitted in succession.

DVD

START LEARNED/TX

SPEAKER

TUNING

BAND

TITLE

MENU/GUIDE

MODE

MEMORY

USE/LEARN T.TONE SET UP

RETURN

STATUS

DISPLAY

ON SCREEN

DOLBY / DTS

SURROUND

DIRECT

DSP SIMULATION

5CH STEREO STEREO

INPUT MODE

ANALOG EXT.IN

MUTING

MASTER VOL.

VOLUME DISC SKIP+

SYSTEM CALL POWER

VDP TUNER SHIFT

TV/DBS PHONO

VCR-1 CD CHANNEL

VCR-2/V.AUX

TV/VCR

AVR/AVC VIDEO DVD TV

AUDIO

VDP VCR

CD

CDR/MDDECK

SYSTEM

SETUP

SURROUND

PARAMETER

CH SELECT

SELECT

RC-881

123
4

SET

A / B

CALL OFF

ENTER

ON / SOURCE

56

789

+10

0

2

1

CDR / TAPE

ENGLISH

30

(3) Storing signals (4) Clearing system call settings

DVD

START LEARNED/TX

SPEAKER

TUNING

BAND

TITLE

MENU/GUIDE

MODE

MEMORY

USE/LEARN T.TONE DVD

SET UP

RETURN

STATUS

DISPLAY

ON SCREEN

DOLBY / DTS
SURROUND

DIRECT

DSP SIMULATION

5CH STEREO STEREO

INPUT MODE

ANALOG EXT.IN

MUTING

MASTER VOL.

VOLUME DISC SKIP+

SYSTEM CALL POWER

VDP TUNER SHIFT

TV/DBS PHONO

VCR-1 CD CHANNEL

VCR-2/V.AUX

TV/VCR

AVR/AVC VIDEO DVD TV

AUDIO

VDP VCR

CD

CDR/MDDECK

SYSTEM

SETUP

SURROUND

PARAMETER

CH SELECT

SELECT

RC-881

123
4

SET

A / B

CALL OFF

ENTER

ON / SOURCE

56

789

+10

0

1,5

2

3

CDR / TAPE

DVD

START LEARNED/TX

SPEAKER

TUNING

BAND

TITLE

MENU/GUIDE

MODE

MEMORY

USE/LEARN T.TONE DVD

SET UP

RETURN

STATUS

DISPLAY

ON SCREEN

DOLBY / DTS

SURROUND

DIRECT

DSP SIMULATION

5CH STEREO STEREO

INPUT MODE

ANALOG EXT.IN

MUTING

MASTER VOL.

VOLUME DISC SKIP+

SYSTEM CALL POWER

VDP TUNER SHIFT

TV/DBS PHONO

VCR-1 CD CHANNEL

VCR-2/V.AUX

TV/VCR

AVR/AVC VIDEO DVD TV

AUDIO

VDP VCR

CD

CDR/MDDECK

SYSTEM

SETUP

SURROUND
PARAMETER

CH SELECT

SELECT

RC-881

123
4

SET

A / B

CALL OFF

ENTER

ON / SOURCE

56

789

+10

0

1,3

2

CDR / TAPE

1

Press the SET button.

• The START LED and LEARNED/TX LED both flash.

SET

2

Press the button at which you want to store the system call
signals.

• The START LED flashes.

3

Set the mode switch to the position for the component
whose remote control signals you want to store.

AVR/AVC VIDEO

AUDIO

4

Press the buttons whose remote control signals you want to
store one by one.

5

Press the SET button.

SET

1

Press the SET button.

SET

2

Press the button whose settings you want to clear.

3

Press the SET button.

• The button is reset to the settings shown on the table on
page 29.

NOTES:

• The remote control signals for the buttons pressed while storing the system call signals are transmitted when the buttons are pressed, so
cover the remote sensor or take other measures so that the components do not operate while the signals are being stored.

• The LEARNED/TX LED does not light if system call signals cannot be stored at the button that you have pressed or if you have already stored
the maximum number of signals.

DVD TV

VDP VCR

CD

CDR/MDDECK

SET