Page 1
DENON AVR control protocol
Application model : AVR-2112CI/AVR-1912
Application terminal: RS-232C
Ethernet
Connector specification
Ⅰ. RS-232C
Connector type: DB-9pin female type, slave straight connection (DCE type)
( 1pin : GND , 2pin : TxD , 3pin : RxD , 5pin : Common(GND) , 4,6,7,8,9pin : NC )
Communication format:
Synchronous system : Tone step synchronization
Communication system : A half duplex
Communication speed : 9600bps
Character length : 8 bits
Parity control : None
Start bit : 1 bit
Stop bit : 1 bit
Communication procedure : Non procedural
Communication data length : 135 bytes (maximum)
Version
7.5.0 15.Apr.’11 Original
Date Contents Page
Ver.7.4.0
- 1 -
Page 2
Ⅱ. Ethernet
Connector type ： RJ-45(10BASE-T/100BASE-TX)
Example ①
PC
Ethernet
Cross cable
Communication system : A half duplex
Communication speed : 10Mbps/100Mbps
Communication port : TCP port 23 (telnet)
Communication data length : 135bytes (maximum)
Example ②
Communication format ：
PC
Ethernet
Straight
cable
HUB
Ethernet
Straight
cable
AVR
AVR
- 2 -
Page 3
NETWORK SETUP of AVR-2112CI/AVR-1912
>Procedure of Network Setup mode.
(1)Press MENU button, then Menu appears on FL-display(and GUI)
(2)Select “Manual Setup > Network Setup > Network Connecting > Detail” .
(3)Set parameters described below.
<DHCP> "ON"---Use this setting when DHCP server is on the local network.
"OFF"---Use this setting when DHCP server is not on the local network.
<IP Address> When <DHCP> sets "OFF”, please set IP address.
When <DHCP> sets "ON”, you can confirm the IP address that is set by server.
<Subnet Mask> When <DHCP> sets "OFF”, please se t Subnet Mask.
When <DHCP> sets "ON”, you can confirm the Subnet Mask that is set by server.
<Gateway> Set the address of Gateway when Gateway is on the local network.
Do not set this parameter when Gateway is not on the local network.
<Primary DNS> Do not set this parameter.
<Second DNS> Do not set this parameter.
<Proxy> Set this parameter "OFF".
<Network Option: Network Standby Mode>
(1)Press MENU button, then Menu appears on FL-display (and GUI)
(2)Select “Manual Setup > Network Setup > Other > Network Standby”
(3)Set parameters described below.
“ON”---Use this setting when using the AVR-2112CI/AVR-1912 Connected in a network.
“OFF”--- Use this setting when not using the AVR-2112CI/AVR-1912 connected in a network.
This setting is reducing the power consumption in the standby mode.
- 3 -
Page 4
Protocol specification
The following three data forms are defined.
COMMAND : The message sent to a system(AVR) from a controller(Touch Panel etc.)
A command to a system is given from a controller.
EVENT : The message sent to a controller (Touch Panel etc.) from a system (AVR)
The result is sent, when a system is operated directly and a state changes.
*The form of EVENT presupposes that it is the same as that of COMMAND.
**Refer to the following table for the contents of COMMAND and EVENT.
RESPONSE : The message sent to a controller (Touch Panel etc.) from a system (AVR)
if the ‘request command’ (COMMAND+?+CR(0x0D)) has came from a controller.
The RESPONSE should be sent within 200ms
*The form of RESPONSE presupposes that it is the same as that of EVENT.
Basic specification: The command by ASCII CODE, parameter expression
*ASCII CODE which can be used is from 0x20 to 0x7F: the alphabet and the number of 0-9, and space (0x20), some signs,
AND carriage return (0x0D) --- It is used only as a pause sign.
Command structure: COMMAND + PARAMETER + CR (0x0D)
COMMAND: ASCII CODE of 2 characters
Ex. SI : Select Input source
MS : surround Mode Setting
MV : Master Volume setting
PW : system PoWer setting
PARAMETER : ASCII CODE ( up to 25 characters)
ex. DVD : function name
SUPER STADIUM : surround mode name
*Special Parameter--- ? : for request command
of receiving the COMMAND.
- 4 -
Page 5
The example of a command * <CR> is the meaning of 0x0D.
SIDVD<CR> : Select Input source DVD
MSSTEREO<CR> : surround Mode Set to STEREO
MVUP<CR> : Master Volume UP
PWON<CR> : system PoWer ON
PWSTANDBY<CR> : system PoWer STANDBY
SI?<CR> : Request command for now playing input source >> Return RESPONSE ‘SI***<CR>’
- 5 -
Page 6
Others
A) COMMAND is receivable also during transmission of EVENT.
B) Since CHANNEL VOLUME changes simultaneously when the SURROUND MODE changes, the value of the channel volume of all channels
returns as EVENT.
C) CHANNEL VOLUME returns the data of ALL channels by the present SURROUND MODE also including an intact channel. In this case,
the data of an intact channel is set to "50".
D) Since SURROUND MODE changes simultaneously when the INPUT source changes, the SURROUND MODE (and also the value of the channel
volume of all channels , It described in B) ) returns as EVENT.
E) When SURROUND MODE is the same in between INPUT source change before and after, EVENT of SURROUND MODE and CHANNEL VOLUME
does NOT return.
F) Although EVENT of SURROUND MODE returns when the present SURROUND MODE is set up again, CHANNEL VOLUME does NOT return.
G) When SURROUND MODE is changed, before returning SURROUND MODE after change as EVENT, the present SURROUND MODE is returned.
H) The RESPONSE should be sent as opposed to the request command by all the commands with which an EVENT exists , not need to
the another request commands(ex. SV command).
I) The PARAMETER (with COMMAND and RESPONSE, EVENT) of minimum level of MASTER VOLUME defines “99”.
J) If the MASTER VOLUME & CHANNEL VOLUME set with 0.5dB step, the PARAMETER (with COMMAND and RESPONSE, EVENT) defines three
ASCII characters as bellows.
Ex. MASTER VOLUME = +1.0dB : MV81<CR>
+0.5dB : MV805<CR>
0dB : MV80<CR>
-0.5dB : MV795<CR>
-1.0dB : MV79<CR>
| |
-79.5dB : MV005<CR>
-80.0dB : MV00<CR>
--- : MV99<CR>
* At the **.0dB step, only uses two ASCII characters as PARAMETER, same as usual.
K) 1 seconds later, please transmit the next COMMAND after transmitting a power on COMMAND（PWON）.
-80.5dB : MV995<CR>
- 6 -
Page 7
COMMAND and PARAMETER list
COMMAND PARAMETER
PW ON POWER ON/STANDBY change PWON<CR>
STANDBY PWSTANDBY<CR>
? Return PW Status PW?<CR>
MV UP MASTER VOLUME UP/DOWN , direct change to **dB MVUP<CR>
DOWN MVDOWN<CR>
**
? Return MV Status MV?<CR>
CV FL UP CHANNEL VOLUME UP/DOWN , direct change to **dB CVFL UP<CR>
FL DOWN ---FRONT Lch CVFL DOWN<CR>
FL ** **:38 to 62 by ASCII , 50=0dB CVFL 50<CR>
FR UP CVFR UP<CR>
FR DOWN ---FRONT Rch CVFR DOWN<CR>
FR ** **:38 to 62 by ASCII , 50=0dB CVFR 50<CR>
C UP CVC UP<CR>
C DOWN ---CENTERch CVC DOWN<CR>
C ** **:38 to 62 by ASCII , 50=0dB CVC 50<CR>
SW UP CVSW UP<CR>
SW DOWN ---SUBWOOFERch CVSW DOWN<CR>
SW ** **:38 to 62 by ASCII , 50=0dB,00=OFF CVSW 50<CR>
SL UP CVSL UP<CR>
SL DOWN ---SURROUND Lch CVSL DOWN<CR>
SL ** **:38 to 62 by ASCII , 50=0dB CVSL 50<CR>
SR UP CVSR UP<CR>
SR DOWN ---SURROUND Rch CVSR DOWN<CR>
SR ** **:38 to 62 by ASCII , 50=0dB CVSR 50<CR>
SBL UP ---SURROUND BACK Lch (SBch 2SP) CVSBL UP<CR>
SBL DOWN CVSBL DOWN<CR>
SBL ** **:38 to 62 by ASCII , 50=0dB CVSBL 50<CR>
SBR UP ---SURROUND BACK Rch (SBch 2SP) CVSBR UP<CR>
SBR DOWN CVSBR DOWN<CR>
SBR ** **:38 to 62 by ASCII , 50=0dB CVSBR 50<CR>
MV, CV COMMAND : "*" parameter uses two or three ASCII characters. (see page6 J) section)
**:00 to 99 by ASCII , 80=0dB, 99=---(MIN) 995=-80.5dB
function example
MV80<CR>
- 7 -
Page 8
COMMAND PARAMETER
CV SB UP ---SURROUND BACKch (SBch 1SP) CVSB UP<CR>
SB DOWN CVSB DOWN<CR>
SB ** **:38 to 62 by ASCII , 50=0dB CVSB 50<CR>
FHL UP CVFHL UP<CR>
FHL DOWN ---FRONT HEIGHT Lch CVFHL DOWN<CR>
FHL ** **:38 to 62 by ASCII , 50=0dB CVFHL 50<CR>
FHR UP CVFHR UP<CR>
FHR DOWN ---FRONT HEIGHT Rch CVFHR DOWN<CR>
FHR ** **:38 to 62 by ASCII , 50=0dB CVFHR 50<CR>
? Return CV Status CV?<CR>
MU ON OUTPUT MUTE ON/OFF change MUON<CR>
OFF MUOFF<CR>
? Return MU Status MU?<CR>
SI CD Select INPUT source SICD<CR>
TUNER
DVD SIDVD<CR>
BD SIBD<CR>
TV SITV<CR>
SAT/CBL SISAT/CBL<CR>
GAME SIGAME<CR>
V.AUX SIV.AUX<CR>
DOCK SIDOCK<CR>
IPOD Select iPod (dock or USB) and PLAY SIIPOD<CR>
CV COMMAND : "*" parameter uses two or three ASCII characters. (see page6 J) section)
GAME2 SIGAME2<CR>
function example
SITUNER<CR>
- 8 -
Page 9
COMMAND PARAMETER
SI NET/USB SINET/USB<CR>
RHAPSODY (North America model Only) SIRHAPSODY<CR>
NAPSTER (North America & Europe model Only) SINAPSTER<CR>
PANDORA (North America model Only) SIPANDORA<CR>
LASTFM (Europe model Only) SILASTFM<CR>
FLICKR SIFLICKR<CR>
FAVORITES SIFAVORITES<CR>
IRADIO SIIRADIO<CR>
SERVER SISERVER<CR>
USB/IPOD Select USB or iPod Direct SIUSB/IPOD<CR>
USB Select INPUT source NET/USB and USB Start Playback SIUSB<CR>
IPD Select INPUT source NET/USB and iPod Direct Start Playback SIIPD<CR>
? Return SI Status SI?<CR>
ZM ON MAIN ZONE ON/OFF change ZMON<CR>
OFF ZMOFF<CR>
? Return ZM Status ZM?<CR>
IRP
FVP
Select INPUT source NET/USB and Internet Radio Start Playback
Select INPUT source NET/USB and Favorites Start Playback
function example
SIIRP<CR>
SIFVP<CR>
- 9 -
Page 10
COMMAND PARAMETER
SD AUTO set AUTO mode (Priority:HDMI>>DIGITAL>>ANALOG) SDAUTO<CR>
HDMI set force HDMI INPUT mode SDHDMI<CR>
DIGITAL set force DIGITAL INPUT (Optical,Coaxial)mode SDDIGITAL<CR>
ANALOG set force ANALOG INPUT mode SDANALOG<CR>
? Return SD Status SD?<CR>
DC AUTO set DIGITAL INPUT AUTO mode DCAUTO<CR>
SV DVD VIDEO SELECT mode set , and select source SVDVD<CR>
BD SVBD<CR>
TV SVTV<CR>
SAT/CBL SVSAT/CBL<CR>
GAME SVGAME<CR>
V.AUX SVV.AUX<CR>
DOCK SVDOCK<CR>
SOURCE VIDEO SELECT mode cancel SVSOURCE<CR>
? Return SV Status SV?<CR>
SLP OFF MAIN ZONE SLEEP TIMER setting SLPOFF<CR>
*** ***:001 to 120 by ASCII , 010=10min SLP120<CR>
? Return SLP Status SLP?<CR>
PCM set DIGITAL INPUT force PCM mode DCPCM<CR>
DTS set DIGITAL INPUT force DTS mode DCDTS<CR>
? Return DC Status DC?<CR>
GAME2 SVGAME2<CR>
function example
- 10 -
Page 11
COMMAND PARAMETER
MS
DIRECT MSDIRECT<CR>
PURE DIRECT MSPURE DIRECT<CR>
STEREO MSSTEREO<CR>
STANDARD MSSTANDARD<CR>
DOLBY DIGITAL MSDOLBY DIGITAL<CR>
DTS SUROUND MSDTS SURROUND<CR>
MCH STEREO ---5/7CH STEREO mode MSMCH STEREO<CR>
ROCK ARENA MSROCK ARENA<CR>
JAZZ CLUB MSJAZZ CLUB<CR>
MONO MOVIE MSMONO MOVIE<CR>
MATRIX MSMATRIX<CR>
VIDEO GAME MSVIDEO GAME<CR>
VIRTUAL MSVIRTUAL<CR>
? Return MS Status MS?<CR>
QUICK1 QUICK SELECT 1-5 MODE SELECT MSQUICK1<CR>
QUICK2 MSQUICK2<CR>
QUICK3 MSQUICK3<CR>
QUICK4 MSQUICK4<CR>
QUICK5 MSQUICK5<CR>
QUICK1 MEMORY QUICK SELECT 1-5 MODE MEMORY MSQUICK1 MEMORY<CR>
QUICK2 MEMORY MSQUICK2 M EMORY<CR>
QUICK3 MEMORY MSQUICK3 M EMORY<CR>
QUICK4 MEMORY MSQUICK4 M EMORY<CR>
QUICK5 MEMORY MSQUICK5 M EMORY<CR>
QUICK ? Return MSQUICK Status MSQUICK ?<CR>
MOVIE
MUSIC
GAME
Select SURROUND mode
function example
MSMOVIE<CR>
MSMUSIC<CR>
MSGAME<CR>
- 11 -
Page 12
COMMAND PARAMETER
VS AUDIO AMP Set HDMI AUDIO Output to AMP VSAUDIO AMP<CR>
AUDIO TV Set HDMI AUDIO Output to TV VSAUDIO TV<CR>
AUDIO ? Return VSAUDIO Status VSAUDIO ?<CR>
VPMAUTO Set Video Processing Mode to AUTO VSVPMAUTO<CR>
VPMGAME Set Video Processing Mode to GAME VSVPMGAME<CR>
VPMMOVI Set Video Processing Mode to MOVIE VSVPMMOVI<CR>
VPM ? Return VSVPM Status VSVPM ?<CR>
function example
- 12 -
Page 13
COMMAND PARAMETER
PS TONE CTRL OFF PARAMETER setting PSTONE CTRL OFF<CR>
TONE CTRL ON TONE CONTROL ON/OFF PSTONE CTRL OFF<CR>
TONE CTRL ? Return PSTONE CONTROL Status PSTONE CTRL ?<CR>
SB:MTRX ON SURROUND BACK SP MODE set PSSB:MTRX ON<CR>
SB:PL2x CINEMA PSSB:PL2X CINEMA<CR>
SB:PL2x MUSIC PSSB:PL2X MUSIC<CR>
SB:ON PSSB:ON<CR>
SB:OFF PSSB:OFF<CR>
SB: ? Return PSSB: Status PSSB: ?<CR>
CINEMA EQ.ON CINEMA EQ. ON/OFF PSCINEMA EQ.ON<CR>
CINEMA EQ.OFF PSCINEMA EQ.OFF<CR>
CINEMA EQ. ? Return PSCINEMA EQ.Status PSCINEMA EQ. ?<CR>
MODE:MUSIC CINEMA / MUSIC / GAME / PL mode change PSMODE:MUSIC<CR>
MODE:CINEMA (This parameter can change DOLBY PL2,PL2x,NEO:6 mode.) PSMODE:CINEMA<CR>
MODE:GAME
MODE:PRO LOGIC --- GAME can change DOLBY PL2 & PL2x mode PSMODE:PRO LOGIC<CR>
--- PL can change ONLY DOLBY PL2 mode
MODE: ? Return PSMODE: Status PSMODE: ?<CR>
FH:ON FRONT HEIGHT ON/OFF PSFH:ON<CR>
FH:OFF PSFH:OFF<CR>
FH: ? Return PSFH: Status PSFH: ?<CR>
PHG LOW
PHG MID PSPHG MID<CR>
PHG HI PSPHG HI<CR>
PHG ? Return PSPHG Status PSPHG ?<CR>
---SB=ON：PL2x mode / SB=OFF：PL2 mode
PLⅡz HEIGHT GAIN direct change
function example
PSMODE:GAME<CR>
PSPHG LOW<CR>
- 13 -
Page 14
COMMAND PARAMETER
PS MULTEQ:AUDYSSEY MultEQ XT/MultEQ mode direct change PSMULTEQ:AUDYSSEY<CR>
MULTEQ:BYP.LR PSMULTEQ:BYP.LR<CR>
MULTEQ:FLAT PSMULTEQ:FLAT<CR>
MULTEQ:MANUAL PSMULTEQ:MANUAL<CR>
MULTEQ:OFF PSMULTEQ:OFF<CR>
MULTEQ: ? Return PSMULTEQ: Status PSMULTEQ: ?<CR>
DYNEQ ON Dynamic EQ = ON PSDYNEQ ON<CR>
DYNEQ OFF Dynamic EQ = OFF PSDYNEQ OFF<CR>
DYNEQ ? Return PSDYNEQ Status PSDYNEQ ?<CR>
REFLEV 5 Reference Level Offset=5dB PSREFLEV 5<CR>
REFLEV 10 Reference Level Offset=10dB PSREFLEV 10<CR>
REFLEV 15 Reference Level Offset=15dB PSREFLEV 15<CR>
REFREV ? Return PSREFLEV Status PSREFLEV ?<CR>
DYNVOL NGT Dynamic Volume = Midnight PSDYNVOL NGT<CR>
DYNVOL EVE Dynamic Volume = Evening PSDYNVOL EVE<CR>
DYNVOL DAY Dynamic Volume = Day PSDYNVOL DAY<CR>
DYNVOL ? Return PSDYNVOL Status PSDYNVOL ?<CR>
REFLEV 0 Reference Level Offset=0dB PSREFLEV 0<CR>
function example
- 14 -
Page 15
COMMAND PARAMETER
PS BAS UP BASS UP/DOWN , direct change to **dB PSBAS UP<CR>
BAS DOWN **:00 to 99 by ASCII , 50=0dB PSBAS DOWN<CR>
BAS ** ---AVR-2112CI/AVR-1912 can be operated from -6 to +6(44 to
56)
BAS ? Return PSBAS Status PSBAS ?<CR>
TRE UP TREBLE UP/DOWN , direct change to **dB PSTRE UP<CR>
TRE DOWN **:00 to 99 by ASCII , 50=0dB PSTRE DOWN<CR>
TRE ** ---AVR-2112CI/AVR-1912 can be operated from -6 to +6(44 to
56)
TRE ? Return PSTRE Status PSTRE ?<CR>
DRC AUTO DRC direct change PSDRC AUTO<CR>
DRC LOW PSDRC LOW<CR>
DRC MID PSDRC MID<CR>
DRC HI PSDRC HI<CR>
DRC OFF PSDRC OFF<CR>
DRC ? PSDRC ?<CR>
DCO OFF D.COMP direct change PSDCO OFF<CR>
DCO LOW PSDCO LOW<CR>
DCO MID PSDCO MID<CR>
DCO HIGH PSDCO HIGH<CR>
DCO ? Return PSDCO Status PSDCO ?<CR>
LFE UP LFE UP/DOWN , direct change to **dB PSLEE UP<CR>
LFE DOWN **:00 to 99 by ASCII , 00=0dB, 10=-10dB PSLFE DOWN<CR>
LFE ** ---AVR-2112CI/AVR-1912 can be operated from 0 to -10 PSLFE 10<CR>
LFE ? Return PSLFE Status PSLFE ? <CR>
EFF UP EFFECT UP/DOWN , EFFECT LEVEL direct change to **dB PSEFF UP<CR>
EFF DOWN **:00 to 99 by ASCII , 00=0dB, 10=10dB PSEFF DOWN<CR>
EFF ** ---AVR-2112CI/AVR-1912 can be operated from 1 to 15 PSEFF 10<CR>
EFF ? Return PSEFF Status PSEFF ?<CR>
DEL UP DELAY UP/DOWN , direct change to ***dB PSDEL UP<CR>
DEL DOWN ***:000 to 999 by ASCII , 000=0ms, 300=300ms PSDEL DOWN<CR>
DEL *** ---AVR-2112CI/AVR-1912 can be operated from 0 to 300 PSDEL ***<CR>
DEL ? Return PSDEL Status PSDEL ?<CR>
PS COMMAND : "*" parameter uses two or three ASCII characters. (see page6 J) section)
function example
PSBAS 50<CR>
PSTRE 50<CR>
- 15 -
Page 16
COMMAND PARAMETER
PS AFD ON AFDM ON/OFF PSAFD ON<CR>
AFD OFF PSAFD OFF<CR>
AFD ? Return PSAFD Status PSAFD ?<CR>
PAN ON PANORAMA ON/OFF PSPAN ON<CR>
PAN OFF PSPAN OFF<CR>
PAN ? Return PSPAN Status PSPAN ?<CR>
DIM UP DIMENSION UP/DOWN , direct change to **dB PSDIM UP<CR>
DIM DOWN **:00 to 99 by ASCII , 00=0, PSDIM DOWN<CR>
DIM ** ---AVR-2112CI/AVR-1912 can be operated from 0 to 6 PSDIM **<CR>
DIM ? Return PSDIM Status PSDIM ?<CR>
CEN UP CENTER WIDTH UP/DOWN , direct change to **dB PSCEN UP<CR>
CEN DOWN **:00 to 99 by ASCII , 00=0 PSCEN DOWN<CR>
CEN ** ---AVR-2112CI/AVR-1912 can be operated from 0 to 7 PSCEN 07<CR>
CEN ? Return PSCEN Status PSCEN ?<CR>
CEI UP CENTER IMAGE UP/DOWN , direct change to **dB PSCEI UP<CR>
CEI DOWN **:00 to 99 by ASCII , 00=0.0 PSCEI DOWN<CR>
CEI ** ---AVR-2112CI/AVR-1912 can be operated from 0.0 to 1.0 PSCEI 10<CR>
CEI? Return PSCEI Status OSCEI ?<CR>
SWR ON SW ON/OFF PSSWR ON<CR>
SWR OFF PSSWR OFF<CR>
SWR ? Return PSSWR Status PSSWR ?<CR>
RSZ S ROOM SIZE direct change PSRSZ S<CR>
RSZ MS PSRSZ MS<CR>
RSZ M PSRSZ M<CR>
RSZ ML PSRSZ ML<CR>
RSZ L PSRSZ L<CR>
RSZ ? Return PSRSZ Status PSRSZ ?<CR>
DELAY UP AUDIO DELAY UP/DOWN , direct change to ***dB PSDELAY UP<CR>
DELAY DOWN ***:000 to 999 by ASCII , 000=0ms, 200=200ms PSDELAY DOWN<CR>
DELAY *** ---AVR-2112CI/AVR-1912 can be operated from 0 to 200 PSDELAY 200<CR>
DELAY ? Return PSDELAY Status PSDELAY ?<CR>
PS COMMAND : "*" parameter uses two or three ASCII characters. (see page6 J) section)
function example
- 16 -
Page 17
COMMAND PARAMETER
PS RSTR OFF AUDIO RESTORER direct change PSRSTR OFF<CR>
RSTR MODE1 PSRSTR MODE1<CR>
RSTR MODE2 PSRSTR MODE2<CR>
RSTR MODE3 PSRSTR MODE3<CR>
RSTR ? Return PSRSTR Status PSRSTR ?<CR>
FRONT SPA FRONT SPEAKER direct change PSFRONT SPA<CR>
FRONT SPB PSFRONT SPB<CR>
FRONT SPA+B PSFRONT A+B<CR>
FRONT? Return PSFRONT Status PSFRONT?<CR>
function example
- 17 -
Page 18
COMMAND PARAMETER
Z2 CD ZONE2 mode set , and select source Z2CD<CR>
| ---The name of PARAMETER is |
USB/IPOD the same as that of the time of SI COMMAND. Z2USB/IPOD<CR>
USB Select ZONE2 source NET/USB and USB Start Playback Z2USB<CR>
IPD Select ZONE2 source NET/USB and iPod Direct Start Playback Z2IPD<CR>
SOURCE ZONE2 mode cancel Z2SOURCE<CR>
UP ZONE2 VOLUME UP/DOWN , direct change to **dB Z2UP<CR>
DOWN Z2DOWN<CR>
** **:00 to 99 by ASCII , 80=0dB, 99=---(MIN) 00=-80dB Z280<CR>
ON ZONE2 ON/OFF change Z2ON<CR>
OFF Z2OFF<CR>
? Return Z2 Status Z2?<CR>
Z2MU ON ZONE2 OUTPUT MUTE ON/OFF change Z2MUON<CR>
OFF Z2MUOFF<CR>
? Return Z2MU Status Z2MU?<CR>
Z2CV FL UP ZONE2 CHANNEL VOLUME UP/DOWN , direct change to **dB Z2CVFL UP<CR>
FL DOWN ---FRONT Lch Z2CVFL DOWN<CR>
FL ** **:38 to 62 by ASCII , 50=0dB Z2CVFL 50<CR>
FR UP ZONE2 CHANNEL VOLUME UP/DOWN , direct change to **dB Z2CVFR UP<CR>
FR DOWN ---FRONT Rch Z2CVFR DOWN<CR>
FR ** **:38 to 62 by ASCII , 50=0dB Z2CVFR 50<CR>
? Return Z2CV Status Z2CV?<CR>
Z2、Z2CV COMMAND : "*" parameter uses two ASCII characters. (see page6 J) section)
IRP
FVP
Select ZONE2 source NET/USB and Internet Radio Start Playback
Select ZONE2 source NET/USB and Favorites Start Playback
function example
Z2IRP<CR>
Z2FVP<CR>
NOTE: Z2 COMMAND
Z2**(volume), Z2CV COMMAND
is valid
when “ZONE2” is selected with “Amp Assign” at AVR-1912.
is valid
when “ZONE2” is selected with “Amp Assign” at AVR-2112CI.
- 18 -
Page 19
COMMAND PARAMETER
Z2 QUICK1 ZONE2 QUICK SELECT 1-5 MODE SELECT Z2QUICK1<CR>
QUICK2 Z2QUICK2<CR>
QUICK3 Z2QUICK3<CR>
QUICK4 Z2QUICK4<CR>
QUICK5 Z2QUICK5<CR>
QUICK1 MEMORY ZONE2 QUICK SELECT 1-5 MODE MEMORY Z2QUICK1 MEMORY<CR>
QUICK2 MEMORY Z2QUICK2 MEMORY<CR>
QUICK3 MEMORY Z2QUICK3 MEMORY<CR>
QUICK4 MEMORY Z2QUICK4 MEMORY<CR>
QUICK5 MEMORY Z2QUICK5 MEMORY<CR>
QUICK ? Return Z2QUICK Status Z2QUICK ?<CR>
function example
NOTE: Z2 COMMAND
is valid
when “ZONE2” is selected with “Amp Assign” at AVR-1912.
- 19 -
Page 20
※ ANALOG TUNER Control
COMMAND PARAMETER
TF ANUP TUNER Frequency UP/DOWN TFANUP<CR>
ANDOWN TFANDOWN<CR>
AN******
(6 digits)
AN? Return TF Status TFAN?<CR>
TP ANUP TUNER PRESET CH UP/DOWN , direct change to No.** TPANUP<CR>
ANDOWN TPANDOWN<CR>
AN**
(PRESET No.)
AN? Return TP Status TPAN?<CR>
ANMEM TUNER PRESET MEMORY TPANMEM<CR>
TM ANAM TUNER BAND , MODE Select TMANAM<CR>
---Band set to AM
ANFM ---Band set to FM TMANFM<CR>
AN? Return TM Status TMAN?<CR>
ANAUTO ---Tuning mode set to AUTO mode TMANAUTO<CR>
ANMANUAL ---Tuning mode set to MANUAL mode TMANMANUAL<CR>
TF, TP, TM COMMAND : '*' parameters can NOT operate when INPUT source isn’t TUNER.
ANMEM**
--- ****.** kHz at AM band (>050000 is AM.)
****.** MHz at FM band (<050000 is FM.)
TPANA1<CR>
TUNER PRESET MEMORY, Preset stored at No.**
**:A1-G8
function example
TFAN105000<CR>
(1050.00kHz at AM)
(PRESET No.”A1”)
TPANMEM**<CR>
- 20 -
Page 21
※Network Audio/USB /iPod DIRECT Extended Control
COMMAND PARAMETER
NS 90 “Cursor Up” Control NS90<CR>
91 “Cursor Down” Control NS91<CR>
92 “Cursor Left” Control NS92<CR>
93 “Cursor Right” Control NS93<CR>
94 “Enter (Play/Pause)” Control NS94<CR>
9A “Play” Control(iRadio/mServer/USB)
“Play/Pause” Control(iPod Direct)
9B “Pause” Control
“Play/Pause” Control(iPod Direct)
9C “Stop” Control NS9C<CR>
9D “Skip Plus” Control NS9D<CR>
9E “Skip Minus” Control NS9E<CR>
9H “Repeat One” (USB/iPod DIRECT/ mServer/Rhapsody/Napster) NS9H<CR>
9I “Repeat All” (USB/iPod DIRECT/ mServer/Rhapsody/Napster) NS9I<CR>
9J “Repeat Off” (USB/iPod DIRECT/ mServer/Rhapsody/Napster) NS9J<CR>
9K “Random On/Repeat ALL” (USB/mS erver/Rhapsody/Napster)
“Shuffle Songs” Control (iPod Direct Only)
9M “Random Off” (USB/mServer/Rhap sody/Napster)
“Shuffle Off” Control (iPod Direct Only)
9W
9X “Page Next” Control NS9X<CR>
9Y “Page Previous” Control NS9Y<CR>
PT Enter/Exit PARTY MODE NSPT<CR>
NSA Return Onscreen Disp lay Information List NSA<CR>
(ASCII CODE Character)
NSE Request Onscreen Dis play Information List NSE<CR>
(UTF-8 CODE Character)
NSD * “Direct Character Search”(iRadio/mServer/USB/Rhapsody only) NSD0<CR>
Toggle Switch “Browse Mode/Remote Mode″Control
(iPod Direct Only)
function example
NS9A<CR>
NS9B<CR>
NS9K<CR>
NS9M<CR>
NS9W<CR>
(Return NSA0-NSA8,Refer to Page 38）
(Return NSE0-NSE8,Refer to Page 39）
(*:0-9,A-Z)
- 21 -
Page 22
COMMAND PARAMETER
NS P1 Preset1-3 Call NSP1<CR>
P2 NSP2<CR>
P3 NSP3<CR>
P1 MEM Preset 1-3 Memory NSP1 MEM<CR>
P2 MEM
P3 MEM NSP3 MEM<CR>
P
B**
(PRESET No.)
C**
(PRESET No.)
H
Return Preset 1-3 status（UTF-8）
Preset Call
**：00-55（00:A1/55:G8)
Preset Memory, Preset stored at No.**
**：00-55（00:A1/55:G8)
Return Preset Channel A1-G8 status（UTF-8）
function example
NSP2 MEM<CR>
NSP<CR>
NSB00<CR>
NSC00<CR>
NSH<CR>
- 22 -
Page 23
※iPod dock Extended Control
※iPod Dock which AVR-2112CI/AVR-1912 can connect with is ASD-1R/11R.
COMMAND PARAMETER
IP 90 “Cursor Up” Control IP90<CR>
91 “Cursor Down” Control IP91<CR>
92 “Cursor Left” Control IP92<CR>
93 “Cursor Right” Control IP93<CR>
94 “Enter (Play/Pause)” Control IP94<CR>
9A “Play/Pause” Control IP9A<CR>
9C “Stop” Control IP9C<CR>
9D “Skip Plus” Control IP9D<CR>
9E “Skip Minus” Control IP9E<CR>
9F “Manual Search Plus” Control IP9F<CR>
9G “Manual Search Minus” Control IP9G<CR>
9H “Repeat One” Control IP9H<CR>
9I “Repeat All” Control IP9I<CR>
9J “Repeat Off” Control IP9J<CR>
9K “Shuffle Songs” Control IP9K<CR>
9L “Shuffle Album” Control IP9L<CR>
9M “Shuffle Off” Control IP9M<CR>
9N “MENU” Control IP9N<CR>
9P Switch the “Browse Mode” Control IP9P<CR>
9Q Switch the “Remote Mode” Control IP9Q<CR>
9X “Page Next” Control IP9X<CR>
9Y “Page Previous” Control IP9Y<CR>
IPA Return Onscreen Display Information List IPA<CR>
(ASCII CODE Character)
IPE Request Onscreen Display Information List(iPOD) IPE<CR>
(UTF-8 CODE Character)
function example
(Return IPA0-IPA9,Refer to Page 41-42）
(Return IPE0-IPE9,Refer to Page 43-44）
- 23 -
Page 24
※Cursor/Enter/Menu(Setup)
COMMAND PARAMETER
MN CUP “Cursor Up” Control MNCUP<CR>
CDN “Cursor Down” Control MNCDN<CR>
CLT “Cursor Left” Control MNCLT<CR>
CRT “Cursor Right” Control MNCRT<CR>
ENT “Enter” Control MNENT<CR>
RTN “RETURN” Control MNRTN<CR>
MEN ON “GUI Menu ON” Control MNMEN ON<CR>
MEN OFF “GUI Menu OFF” Control MNMEN OFF<CR>
SRC ON “GUI Source Select Menu ON” Control MNSRC ON<CR>
SRC OFF “GUI Source Select Menu OFF” Control MNSRC OFF<CR>
function example
- 24 -
Page 25
※Remote Lock/Panel Lock
SY REMOTE LOCK ON REMOTE CONTROL LOCK ON/OFF SYREMOTE LOCK ON<CR>
REMOTE LOCK OFF SYREMOTE LOCK OFF<CR>
PANEL LOCK ON PANEL BUTTON (Except MASTER VOL.)CONTROL LOCK ON SYPANEL LOCK ON<CR>
PANEL+V LOCK ON PANEL BUTTON & MASTER VOL. CONTROL LOCK ON SYPANEL+V LOCK ON<CR>
PANEL LOCK OFF PANEL BUTTUM & MASTER VOL. CONTROL LOCK OFF SYPANEL LOCK OFF<CR>
COMMAND PARAMETER
function example
※UPGRADE ID Display
UG IDN ID Number for UPGRADE is displayed on FL Display UGIDN<CR>
COMMAND PARAMETER
function example
- 25 -
Page 26
EVENT(or RESPONSE) and PARAMETER list
PW ON POWER ON/STANDBY change PWON<CR>
STANDBY PWSTANDBY<CR>
MV ** MASTER VOLUME change , **:00 to 99 by ASCII MV80<CR>
98 = 18dB(MAX)
80 = 0dB
00 = -80dB
99 = ---(MIN)
CV FL ** CHANNEL VOLUME change , **:00,38 to 62 by ASCII CVFL 50<CR>
FR ** 62 = +12dB(MAX) CVFR 50<CR>
C ** 50 = 0dB CVC 50<CR>
SW ** 38 = -12dB(MIN) CVSW 50<CR>
SL ** 00 = OFF (define ONLY SWch in DIRECT mode.) CVSL 50<CR>
SR ** CVSR 50<CR>
SBL ** (at SBch 2SP) CVSBL 50<CR>
SBR ** (at SBch 2SP) CVSBR 50<CR>
SB ** (at SBch 1SP) CVSB 50<CR>
FHL ** CVFHL 50<CR>
FHR ** CVFHR 50<CR>
MU ON OUTPUT MUTE ON/OFF change MUON<CR>
OFF MUOFF<CR>
SI CD INPUT source change SICD<CR>
TUNER SITUNER<CR>
DVD SIDVD<CR>
BD SIBD<CR>
TV SITV<CR>
SAT/CBL SISAT/CBL<CR>
GAME SIGAME<CR>
EVENT PARAMETER
995 = -80.5dB
The PARAMETER of MV, CV EVENT : Uses two or three ASCII characters. (see page6 J) section)
function example
- 26 -
Page 27
SI
V.AUX SIV.AUX<CR>
DOCK
IPOD SIIPOD<CR>
NET/USB SINET/USB
RHAPSODY (North America model Only) SIRHAPSODY<CR>
NAPSTER (North America & Europe model Only) SINAPSTER<CR>
PANDORA (North America model Only) SIPANDORA<CR>
LASTFM (Europe model Only) SILASTFM<CR>
FLICKR SIFLICKR<CR>
FAVORITES SIFAVORITES<CR>
IRADIO SIIRADIO<CR>
SERVER SISERVER<CR>
USB DIRECT SIUSB DIRECT<CR>
IPOD DIRECT SIIPOD DIRECT<CR>
USB SIUSB<CR>
IPD SIIPD<CR>
ZM ON MAIN ZONE ON/OFF change ZMON<CR>
OFF ZMOFF<CR>
EVENT PARAMETER
GAME2 SIGAME2<CR>
IRP
FVP
function example
SIDOCK<CR>
SIIRP<CR>
SIFVP<CR>
- 27 -
Page 28
SD AUTO INPUT mode change SDAUTO<CR>
HDMI
DIGITAL
ANALOG SDANALOG<CR>
ARC ARC playing SDARC<CR>
NO No Input SDNO<CR>
DC AUTO DIGITAL INPUT mode change DCAUTO<CR>
PCM DCPCM<CR>
DTS DCDTS<CR>
SV DVD VIDEO SELECT mode source change SVDVD<CR>
BD SVBD<CR>
TV SVTV<CR>
SAT/CBL SVSAT/CBL<CR>
GAME SVGAME<CR>
V.AUX SVV.AUX<CR>
DOCK SVDOCKCR>
SOURCE SVSOURCE<CR>
SLP OFF MAIN ZONE SLEEP TIMER setting change SLPOFF<CR>
*** SLP120<CR>
EVENT PARAMETER
GAME2 SVGAME2<CR>
function example
SDHDMI<CR>
SDDIGITAL<CR>
- 28 -
Page 29
MS DIRECT SURROUND mode change MSDIRECT<CR>
PURE DIRECT MSPURE DIRECT<CR>
STEREO MSSTEREO<CR>
MULTI CH IN MSMULTI CH IN<CR>
M CH IN+PL2X C MSM CH IN+PL2X C<CR>
M CH IN+PL2X M MSM CH IN+PL2X M<CR>
M CH IN+PL2Z H MSM CH IN+PL2Z H<CR>
M CH IN
MULTI CH IN 7.1 MSMULTI CH IN 7.1<CR>
DOLBY PRO LOGIC MSDOLBY PR O LOGIC<CR>
DOLBY PL2 C MSDOLBY PL2 C<CR>
DOLBY PL2 M MSDOLBY PL2 M<CR>
DOLBY PL2 G MSDOLBY PL2 G<CR>
DOLBY PL2X C MSDOLBY PL2X C<CR>
DOLBY PL2X M MSDOLBY PL2X M<CR>
DOLBY PL2X G MSDOLBY PL2X G<CR>
DOLBY PL2Z H MSDOLBY PL2Z H<CR>
DOLBY DIGITAL MSDOLBY DIGITAL<CR>
DOLBY D EX MSDOLBY D EX<CR>
DOLBY D
DOLBY D
DOLBY D
DTS NEO:6 C MSDTS NEO:6 C<CR>
DTS NEO:6 M MSDTS NEO:6 M<CR>
DTS SURROUND MSDTS SURROUND<CR>
DTS ES DSCRT6.1 MSDTS ES DSCRT6.1<CR>
DTS ES MTRX6.1 MSDTS ES MTRX6.1<CR>
DTS+PL2X C MSDTS+PL2X C<CR>
DTS+PL2X M MSDTS+PL2X M<CR>
DTS+PL2Z H MSDTS+PL2Z H<CR>
EVENT PARAMETER
MSM CH IN+ DOLBY EX<CR>
+DOLBY EX
MSDOLBY D+PL2X C<CR>
+PL2X C
MSDOLBY D+PL2X M<CR>
+PL2X M
MSDOLBY D+PL2Z H<CR>
+PL2Z H
function example
- 29 -
Page 30
DTS+NEO:6 MSDTS+NEO:6<CR>
DTS96/24 MSDTS96/24<CR>
DTS96 ES MTRX MSDTS96 ES MTRX<CR>
MCH STEREO ---5/7CH STEREO mode MSMCH STEREO<CR>
ROCK ARENA MSROCK ARENA<CR>
JAZZ CLUB MSJAZZ CLUB<CR>
MONO MOVIE MSMONO MOVIE<CR>
MATRIX MSMATRIX<CR>
VIDEO GAME MSVIDEO GAME<CR>
VIRTUAL MSVIRTUAL<CR>
DOLBY D+ MSDOLBY D+<CR>
DOLBY D+ +EX MSDOLBY D+ +EX<CR>
DOLBY D+ +PL2X C MSDOLBY D+ +PL2X C<CR>
DOLBY D+ +PL2X M MSDOLBY D+ +PL2X M<CR>
DOLBY D+ +PL2Z H MSDOLBY D+ +PL2Z H<CR>
DOLBY TRUEHD MSDOLBY HD<CR>
DOLBY HD MSDOLBY HD<CR>
DOLBY HD+EX MSDOLBY HD+EX<CR>
DOLBY HD+PL2X C MSDOLBY HD+PL2X C<CR>
DOLBY HD+PL2X M MSDOLBY HD+PL2X M<CR>
DOLBY HD+PL2Z H MSDOLBY HD+PL2Z H<CR>
DTS HD MSDTS HD<CR>
DTS HD MSTR MSDTS HD MSTR<CR>
DTS HD+NEO:6 MSDTS HD+NEO:6<CR>
DTS HD+PL2X C MSDTS HD+PL2X C<CR>
DTS HD+PL2X M MSDTS HD+PL2X M<CR>
DTS HD+PL2Z H MSDTS HD+PL2Z H<CR>
DTS ES 8CH DSCRT MSDTS ES 8CH DSCRT<CR>
DTS EXPRESS MSDTS EXPRESS<CR>
MPEG2 AAC (JAPAN model Only) MSMPEG2 AAC<CR>
AAC+DOLBY EX (JAPAN model Only) MSAAC+DOLBY EX<CR>
AAC+PL2X C (JAPAN model Only) MSAAC+PL2X C<CR>
AAC+PL2X M (JAPAN model Only) MSAAC+PL2X M<CR
AAC+PL2Z H (JAPAN model Only) MSAAC+PL2Z H<CR>
EVENT PARAMETER
function example
- 30 -
Page 31
MS QUICK1 QUICK SELECT mode change MSQUICK1<CR>
QUICK2 MSQUICK2<CR>
QUICK3 MSQUICK3<CR>
QUICK4 MSQUICK4<CR>
QUICK5 MSQUICK5<CR>
QUICK0 ---QUICK 1(or 2, 3, 4, 5) Change QUICK SELECT OFF MSQUICK0<CR>
EVENT PARAMETER
function example
- 31 -
Page 32
VS AUDIO AMP HDMI AUDIO Output setting change VSAUDIO AMP<CR>
AUDIO TV VSAUDIO TV<CR>
VPMAUTO Video Mode setting change VSVPMAUTO<CR>
VPMGAME VSVPMGAME<CR>
VPMMOVI VSVPMMOVI<CR>
EVENT PARAMETER
function example
- 32 -
Page 33
PS TONE CTRL OFF TONE CONTROL ON/OFF change PSTONE CTRL OFF<CR>
TONE CTRL ON PSTONE CTRL OFF<CR>
SB:MTRX ON SURROUND BACK MODE change PSSB:MTRX ON<CR>
SB:PL2X CINEMA PSSB:PL2X CINEMA<CR>
SB:PL2X MUSIC PSSB:PL2X MUSIC<CR>
SB:ON PSSB:ON<CR>
SB:OFF PSSB:OFF<CR>
SB:ESMTRX PSSB:ESMTRX<CR>
CINEMA EQ.ON CINEMA EQ. ON/OFF change PSCINEMA EQ.ON<CR>
CINEMA EQ.OFF PSCINEMA EQ.OFF<CR>
MODE:CINEMA CINEMA / MUSIC / GAME / PL /HEIGHT mode change PSMODE:CINEMA<CR>
MODE:MUSIC PSMODE:MUSIC<CR>
MODE:GAME PSMODE:GAME<CR>
MODE:PRO LOGIC PSMODE:PRO LOGIC<CR>
MODE:HEIGHT PSMODE:HEIGHT<CR>
FH:ON FRONT HEIGHT Output change PSFH:ON<CR>
FH:OFF PSFH:OFF<CR>
PHG LOW
PHG MID PSPHG MID<CR>
PHG HI PSPHG HI<CR>
MULTEQ:AUDYSSEY MultEQ XT mode change PSMULTEQ:AUDYSSEY<CR>
MULTEQ:BYP.LR PSMULTEQ:BYP.LR<CR>
MULTEQ:FLAT PSMULTEQ:FLAT<CR>
MULTEQ:MANUAL PSMULTEQ:MANUAL<CR>
MULTEQ:OFF PSMULTEQ:OFF<CR>
DYNEQ ON DYNAMIC EQ change PSDYNEQ ON<CR>
DYNEQ OFF PSDYNEQ OFF<CR>
EVENT PARAMETER
PLⅡz HEIGHT GAIN direct change
function example
PSPHG LOW<CR>
- 33 -
Page 34
PS REFLEV 0 Reference Level Offset change PSREFLEV 0<CR>
REFLEV 5 PSREFLEV 5<CR>
REFLEV 10 PSREFLEV 10<CR>
REFLEV 15 PSREFLEV 15<CR>
DYNVOL NGT DYNAMIC VOLUME change PSDYNVOL NGT<CR>
DYNVOL EVE PSDYNVOL EVE<CR>
DYNVOL DAY PSDYNVOL DAY<CR>
BAS ** BASS change PSBAS 50<CR>
TRE ** TREBLE change PSTRE 50<CR>
DRC AUTO DRC change PSDRC AUTO<CR>
DRC LOW PSDRC LOW<CR>
DRC MID PSDRC MID<CR>
DRC HI PSDRC HI<CR>
DRC OFF PSDRC OFF<CR>
DCO OFF D.COMP change PSDCO OFF<CR>
DCO LOW PSDCO LOW<CR>
DCO MID PSDCO MID<CR>
DCO HIGH PSDCO HIGH<CR>
LFE ** LFE change PSLFE 10<CR>
EFF ** EFFECT LEVEL change PSEFF 10<CR>
DEL *** DELAY change PSDEL 100<CR>
EVENT PARAMETER
function example
- 34 -
Page 35
PS AFD ON AFDM change PSAFD ON<CR>
AFD OFF PSAFD OFF<CR>
PAN ON PANORAMA change PSPAN ON<CR>
PAN OFF PSPAN OFF<CR>
DIM ** DIMMENSION change PSDIM 06<CR>
CEN ** CENTER WIDTH change PSCEN 07<CR>
CEI ** CENTER IMAGE change PSCEI 10<CR>
SWR ON SW ON/OFF change PSSWR ON<CR>
SWR OFF PSSWR OFF<CR>
RSZ S ROOM SIZE change PSRSZ S<CR>
RSZ MS PSRSZ MS<CR>
RSZ M PSRSZ M<CR>
RSZ ML PSRSZ ML<CR>
RSZ L PSRSZ L<CR>
DELAY *** AUDIO DELAY change PSDELAY 200<CR>
RSTR OFF AUDIO RESTORER change PSRSTR OFF<CR>
RSTR MODE1 PSRSTR MODE1<CR>
RSTR MODE2 PSRSTR MODE2<CR>
RSTR MODE3 PSRSTR MODE3<CR>
EVENT PARAMETER
FRONT SPA FRONT SPEAKER direct change PSFRONT SPA<CR>
FRONT SPB PSFRONT SPB<CR>
FRONT SPA+B PSFRONT A+B<CR>
function example
- 35 -
Page 36
Z2 CD ZONE2 source change Z2CD<CR>
| ---The name of PARAMETER is |
USB DIRECT
SOURCE ZONE2 mode cancel Z2SOURCE<CR>
QUICK1 ZONE2 QUICK SELECT mode change Z2QUICK1<CR>
QUICK2 Z2QUICK2<CR>
QUICK3 Z2QUICK3<CR>
QUICK4 Z2QUICK4<CR>
QUICK5 Z2QUICK5<CR>
QUICK0 ---Z2 QUICK SELECT 1(or 2, 3, 4, 5)
** ZONE2 VOLUME change , **:00 to 99 by ASCII Z280<CR>
98 = 18dB(MAX)
80 = 0dB
10 = -70dB
99 = ---(MIN)
ON ZONE2 ON/OFF change Z2ON<CR>
OFF Z2OFF<CR>
Z2MU ON ZONE2 OUTPUT MUTE ON/OFF change Z2MUON<CR>
OFF Z2MUOFF<CR>
Z2CV FL ** **:38 to 62 by ASCII , 50=0dB Z2CVFL 50<CR>
FR ** **:38 to 62 by ASCII , 50=0dB Z2CVFR 50<CR>
EVENT PARAMETER
the same as that of the time of SI COMMAND. Z2USB DIRECT<CR>
IPOD DIRECT
Change QUICK SELCT OFF
00 = -80dB
The PARAMETER of Z2 EVENT : Uses two ASCII characters. (see page4 J) section)
function example
Z2IPOD DIRECT<CR>
Z2QUICK0<CR>
- 36 -
Page 37
※ANALOG TUNER Control
TF AN******
--- ****.** kHz at AM band (1050.00kHz at AM)
****.** MHz at FM band
TP AN**(PRESET No.) TUNER PRESET change to No.** TPANA1<CR>
(PRESET No.”A1”)
ANOFF Change Preset Channel select OFF TPANOFF<CR>
TM ANAM TUNER BAND , MODE change TMANAM<CR>
---Band set to AM
ANFM ---Band set to FM TMANFM<CR>
ANAUTO ---Tuning mode set to AUTO mode TMANAUTO<CR>
ANMANUAL ---Tuning mode set to MANUAL mode TMANMANUAL<CR>
EVENT PARAMETER
TUNER Frequency change TFAN105000<CR>
(6 digits)
ANMEM** TUNER PRESET MEMORY TPANMEMA1<CR>
function example
- 37 -
Page 38
※Network Audio/USB /iPod DIRECT Extended Control
NSA Onscreen Display Information is Answered
0 Display Line1 Information NSA0**************_?????<CR>
1 Display Line3 Information
2 Display Line4 Information
3 Display Line5 Information
4 Display Line6 Information
5 Display Line7 Information
6 Display Line8 Information
7 Display Line9 Information NSA7**************_?????<CR>
8 Display Line10 Information NSA8**************_?????<CR>
NSA0Now Playing USB_????<CR>
EVENT PARAMETER
By the NSA Command.
function example
NSA1※************_?????<CR>
NSA2※************_?????<CR>
NSA3※************_?????<CR>
NSA4※************_?????<CR>
NSA5※************_?????<CR>
NSA6※************_?????<CR>
*:Character Length MAX96byte
_:Null
?:Exclusion(The character after Null
should be disregarded)
※:Cursor&Playable
Information Data(1Byte)
Bit1:Playable Music
Bit2:Directory
Bit4:CURSOR SELECT=1
Bit7:Picture
Bit3,5,6,8:Don't Care
NSA1※Come Away With Me_???<CR>
NSA2※Norah Jones_?????????<CR>
NSA3※_????????????????????<CR>
NSA4※_????????????????????<CR>
NSA5※00:11 100%_???????<CR>
NSA6※_????????????????????<CR>
NSA7_????????????????????<CR>
NSA8_????????????????????<CR>
- 38 -
Page 39
NSE Onscreen Display Information(mServer/iRadio) is
0 Display Line1 Information NSE0**************_?????<CR>
1 Display Line3 Information
2 Display Line4 Information
3 Display Line5 Information
4 Display Line6 Information
5 Display Line7 Information
6 Display Line8 Information
7 Display Line9 Information NSE7**************_?????<CR>
8 Display Line10 Information NSE8**************_?????<CR>
<example>
EVENT PARAMETER
Answered By the NSE Command.
function example
NSE1※************_?????<CR>
NSE2※************_?????<CR>
NSE3※************_?????<CR>
NSE4※************_?????<CR>
NSE5※************_?????<CR>
NSE6※************_?????<CR>
*:UTF-8 CODE
_:Null
?: Don't Care (The character after Null
should be disregarded)
※:Cursor&Playable
Information Data(1Byte)
Bit1:Playable Music =1
Bit2:Directory
Bit4:CURSOR SELECT=1
Bit7:Picture
Bit3,5,6,8:Don't Care
************_?????:96byte Fixed
NSE0Now Playing USB_????<CR>
NSE1※Come Away With Me_???<CR>
NSE2※Norah Jones_?????????<CR>
NSE3※_????????????????????<CR>
NSE4※_????????????????????<CR>
NSE5※00:11 100%_???????<CR>
NSE6※_????????????????????<CR>
NSE7_????????????????????<CR>
NSE8_????????????????????<CR>
Character(MAX96byte)
- 39 -
Page 40
COMMAND PARAMETER
NS P1 Preset1-3 Call NSP1<CR>
P2 NSP2<CR>
P3 NSP3<CR>
P1 MEM Preset 1-3 Memory NSP1 MEM<CR>
P2 MEM
P3 MEM NSP3 MEM<CR>
P
B**
(PRESET No.)
C**
(PRESET No.)
H
Return Preset 1-3 status（UTF-8）
Preset Call
**：00-55（00:A1/55:G8)
Preset Memory, Preset stored at No.**
**：00-55（00:A1/55:G8)
Return Preset Channel A1-G8 status（UTF-8）
(00:A1-55:G8)
function example
NSP2 MEM<CR>
NSP01**********(20 digits)<CR>
NSP02**********(20 digits)<CR>
NSP03**********(20 digits)<CR>
***:Station name or Title name
NSB00<CR>
NSC00<CR>
NSH00**********(20 digits)<CR>
NSH01**********(20 digits)<CR>
|
NSH54**********(20 digits)<CR>
NSH55**********(20 digits)<CR>
- 40 -
Page 41
※iPod Extended Control
iPod Dock which AVR-2112CI/AVR-1912 can connect with is ASD-1R/11R.
IPA Onscreen Display Information is Answered
0 Display Line1 Information IPA0***************_???<CR>
1 Display Line3 Information
2 Display Line4 Information
3 Display Line5 Information
4 Display Line6 Information
5 Display Line7 Information
6 Display Line8 Information
7 Display Line9 Information
8 Display Line10 Information IPA8#**************_???<CR>
9 Display Line11 Information IPA9***************_???<CR>
EVENT PARAMETER
By the IPA Command.
function example
IPA1※*************_???<CR>
IPA2※*************_???<CR>
IPA3※*************_???<CR>
IPA4※*************_???<CR>
IPA5※*************_???<CR>
IPA6※*************_???<CR>
IPA7※*************_???<CR>
*:Character Length MAX96byte
_:Null
?:Exclusion(The character after Null
should be disregarded)
※:Cursor Information Data(1Byte)
Bit1:Playable Music/Video=1
Bit2:Directory=1
Bit4:CURSOR SELECT=1
Bit3,5,6,7,8:Don't Care
#：Bit1-8:Don’t Care
- 41 -
Page 42
IPA <example1>
EVENT PARAMETER
function example
IPA0Artist??????????????????<CR>
IPA1※ Ana Caram_????????????<CR>
IPA2※ Badi Assad_???????????<CR>
IPA3※ Christy Baron_????????<CR>
IPA4※ Marta Gomez_??????????<CR>
IPA5※ Rebecca Pidgeon_??????<CR>
IPA6※ Sara K_???????????????<CR>
IPA7※ Valerie Joyce_????????<CR>
IPA8# SFL Songs RPT All_???<CR>
IPA9 [ 2/ 6]_?????????<CR>
<example2>
IPA0Now Playing iPod_???????<CR>
IPA1※ A HARD DAY'S NIGHT._??<CR>
IPA2※ /The Beatles_?????????<CR>
IPA3※_??????????????????????<CR>
IPA4※ A HARD DAY'S NIGHT_???<CR>
IPA5※ 00:04_??????????????<CR>
IPA6※_??????????????????????<CR>
IPA7※_??????????????????????<CR>
IPA8# SFL Songs RPT All_???<CR>
IPA9????????????????????????<CR>
- 42 -
Page 43
?
IPE Onscreen Display Information(iPod) is Answered
0 Display Line1 Information IPE0***************_???<CR>
1 Display Line3 Information
2 Display Line4 Information
3 Display Line5 Information
4 Display Line6 Information
5 Display Line7 Information
6 Display Line8 Information
7 Display Line9 Information
8 Display Line10 Information IPE8#**************_???<CR>
9 Display Line11 Information
EVENT PARAMETER
By the IPA Command.
function example
IPE1※*************_???<CR>
IPE2※*************_???<CR>
IPE3※*************_???<CR>
IPE4※*************_???<CR>
IPE5※*************_???<CR>
IPE6※*************_???<CR>
IPE7※*************_???<CR>
IPE9***************_???<CR>
*:UTF-8 CODE
_:Null
:Exclusion(The character after Null
should be disregarded)
※:Cursor Information Data(1Byte)
Bit1:Playable Music/Video=1
Bit2:Directory=1
Bit3:Don't Care
Bit4:CURSOR SELECT=1
Bit3,5,6,7,8:Don't Care
#：Bit1-8:Don’t Care
Character(MAX96byte)
- 43 -
Page 44
EVENT PARAMETER
IPE <example1>
function example
IPE0Artist??????????????????<CR>
IPE1※ Ana Caram_????????????<CR>
IPE2※ Badi Assad_???????????<CR>
IPE3※ Christy Baron_????????<CR>
IPE4※ Marta Gomez_??????????<CR>
IPE5※ Rebecca Pidgeon_??????<CR>
IPE6※ Sara K_???????????????<CR>
IPE7※ Valerie Joyce_????????<CR>
IPE8# SFL Songs RPT All_???<CR>
IPE9 [ 2/ 6]_?????????<CR>
<example2>
IPE0Now Playing iPod_???????<CR>
IPE1※ A HARD DAY'S NIGHT._??<CR>
IPE2※ /The Beatles_?????????<CR>
IPE3※_??????????????????????<CR>
IPE4※ A HARD DAY'S NIGHT_???<CR>
IPE5※ 00:04_??????????????<CR>
IPE6※_??????????????????????<CR>
IPE7※_??????????????????????<CR>
IPE8# SFL Songs RPT All_???<CR>
IPE9_??????????????????????<CR>
- 44 -
Page 45
※Remote Lock/Panel Lock
SY REMOTE LOCK ON REMOTE CONTROL LOCK ON/OFF SYREMOTE LOCK ON<CR>
REMOTE LOCK OFF SYREMOTE LOCK OFF<CR>
PANEL LOCK ON PANEL BUTTON(Except MASTER VOL.)CONTROL LOCK ON SYPANEL LOCK ON<CR>
PANEL+V LOCK ON PANEL BUTTON & MASTER VOL. CONTROL LOCK ON SYPANEL+V LOCK ON<CR>
PANEL LOCK OFF PANEL BUTTUM & MASTER VOL. CONTROL LOCK OFF SYPANEL LOCK OFF<CR>
EVENT PARAMETER
function example
※UPGRADE ID Display
COMMAND PARAMETER
IDN ************ ID Number for UPGRADE is displayed on FL Display
************:12-digit ID Number
IDN NG Can’t get ID number from DPMS UGIDN NG<CR>
function example
UGIDN ************<CR> UG
- 45 -
Page 46
Extension COMMAND
・The RC code can be sent from Serial protocol commands
Protocol specification
Command structure: COMMAND + RC FORMAT + RC DATA + CR (0x0D)
COMMAND : ASCII CODE of 2 characters
Ex. RC : RC CODE
RC FORMAT : ASCII CODE of 3 characters
Ex. KSK : KASEIKYO FORMAT
SHP : SHARP FORMAT
RC DATA : ASCII CODE of 7 characters
※For details of the RC CODE , please refer to the IR remote control code list.
KASEIKYO FORMAT
SHARP FORMAT
- 46 -
Page 47
The example of a command * <CR> is the meaning of 0x0D.
RCKSK0410002<CR> : All Power ON by using KASEIKYO FORMAT
RCSHP0230033<CR> : All Power ON by using SHARP FORMAT
- 47 -
Loading...