Page 1
DENON AVR/AVC control protocol
Application model : AVR-4806/AVC-A11XV
Application terminal : RS-232C/ Ethernet
Connector specification
Ⅰ . RS-232C
Connector type : DB-9pin female type, slave straight connection (DCE type)
( 1pin : GND , 2pin : TxD , 3pin : RxD , 5pin : Common(GND) , 4,6,7,8,9pin : NC )
Communication format :
Synchronous system : Tone step synchronization
Communication system : A half duplex
Communication speed : 9600bps
Character length : 8 bits
Parity control : None
Start bit : 1 bit
Stop bit : 1 bit
Communication procedure : Non procedural
Communication data length : 135 bytes (maximum)
Ver. 4.4
- 1 -
Page 2
Ⅱ . Ethernet
p
p
Connector type ： RJ-45(10BASE-T/100BASE-TX)
Exam
Exam
le ①
le ②
PC
PC
Ethernet
Straight
cable
Ethernet
Cross cable
HUB
Ethernet
Straight
cable
AVR/AVC
AVR/AVC
Communication format ：
Communication system : A half duplex
Communication speed : 10Mbps/100Mbps
Communication port : TCP port 23 (telnet)
Communication data length : 135bytes (maximum)
- 2 -
Page 3
NETWORK SETUP of AVR-4806/AVC-A11XV
>Procedure of Network Setup mode.
(1)Push the POWER switch during STANDARD button and INPUT MODE button press simultaneously.
(2)Press SYSTEM SETUP button, then System Setup Menu appears on FL-display(and OSD)
(3)Select Option Setup and select Network Setup.
(4)Set parameters described below.
<DHCP> "ON"---Use this setting when DHCP server is on the local network.
"OFF"---Use this setting when DHCP server is not on the local network.
<IP Address> When <DHCP> sets "OFF”, please set IP address.
When <DHCP> sets "ON”, you can confirm the IP address that is set by server.
<Subnet Mask> When <DHCP> sets "OFF”, please set Subnet Mask.
When <DHCP> sets "ON”, you can confirm the Subnet Mask that is set by server.
<Gateway> Set the address of Gateway when Gateway is on the local network.
Do not set this parameter when Gateway is not on the local network.
<Primary DNS> Do not set this parameter.
<Second DNS> Do not set this parameter.
<Proxy> Set this parameter "OFF".
- 3 -
Page 4
Protocol specification
The following three data forms is defined.
COMMAND : The message sent to a system(AVR/AVC) from a controller(Touch Panel etc.)
A command to a system is given from a controller.
EVENT : The message sent to a controller(Touch Panel etc.) from a system(AVR/AVC)
The result is sent, when a system is operated directly and a state changes.
*The form of EVENT presupposes that it is the same as that of COMMAND.
**Refer to the following table for the contents of COMMAND and EVENT.
RESPONSE : The message sent to a controller(Touch Panel etc.) from a system(AVR/AVC)
if the ‘request command’ (COMMAND+?+CR(0x0D)) has came from a controller.
The RESPONSE should be sent within 200ms
*The form of RESPONSE presupposes that it is the same as that of EVENT.
Basic specification : The command by ASCII CODE, parameter expression
*ASCII CODE which can be used is from 0x20 to 0x7F : the alphabet and the number of 0-9 , and space (0x20) , Some signs ,
AND carriage return(0x0D)--- It is used only as a pause sign.
Command structure : COMMAND + PARAMETER + CR(0x0D)
COMMAND : ASCII CODE of 2 characters
ex. SI : Select Input source
MS : surround Mode Setting
MV : Master Volume setting
PW : system PoWer setting
PARAMETER : ASCII CODE ( up to 25 characters)
ex. DVD : function name
CDR/TAPE-1 : function name
THX SURROUND EX : surround mode name
SUPER STADIUM : surround mode name
*Special Parameter--- ? : for request command
of receiving the COMMAND.
- 4 -
Page 5
The example of a command * <CR> is the meaning of 0x0D.
SIDVD<CR> : Select Input source DVD
MSTHX SURROUND EX<CR> : surround Mode Set to THX SURROUND EX
MVUP<CR> : Master Volume UP
PWON<CR> : system PoWer ON
PWSTANDBY<CR> : system PoWer STANDBY
SI?<CR> : Request command for now playing input source >> Return RESPONSE ‘SI***<CR>’
- 5 -
Page 6
Others
A) COMMAND is receivable also during transmission of EVENT.
B) Since CHANNEL VOLUME changes simultaneously when the SURROUND MODE changes, the value of the channel volume of all channels
returns as EVENT.
C) CHANNEL VOLUME returns the data of ALL channels by the present SURROUND MODE also including an intact channel. In this case,
the data of an intact channel is set to "50".
D) Since SURROUND MODE changes simultaneously when the INPUT source changes, the SURROUND MODE (and also the value of the channel
volume of all channels , It described in B) ) returns as EVENT.
E) When SURROUND MODE is the same in between INPUT source change before and after, EVENT of SURROUND MODE and CHANNEL VOLUME
does NOT return.
F) Although EVENT of SURROUND MODE returns when the present SURROUND MODE is set up again, CHANNEL VOLUME does NOT return.
G) When SURROUND MODE is changed, before returning SURROUND MODE after change as EVENT, the present SURROUND MODE is returned.
H) The RESPONSE should be sent as opposed to the request command by all the commands with which an EVENT exists , not need to
the another request commands(ex. SV command).
I) The PARAMETER (with COMMAND and RESPONSE, EVENT) of minimum level of MASTER VOLUME defines “99”.
J) If the MASTER VOLUME & CHANNEL VOLUME set with 0.5dB step, the PARAMETER (with COMMAND and RESPONSE, EVENT) defines three
ASCII characters as bellows.
ex. MASTER VOLUME = +1.0dB : MV81<CR>
+0.5dB : MV805<CR>
0dB : MV80<CR>
-0.5dB : MV795<CR>
-1.0dB : MV79<CR>
| |
-79.5dB : MV005<CR>
-80.0dB : MV00<CR>
--- : MV99<CR>
* At the **.0dB step, only uses two ASCII characters as PARAMETER, same as usual.
- 6 -
Page 7
COMMAND and PARAMETER list
PW ON POWER ON/STANDBY change PWON<CR>
STANDBY PWSTANDBY<CR>
MV UP MASTER VOLUME UP/DOWN , direct change to **dB MVUP<CR>
DOWN MVDOWN<CR>
** **:00 to 99 by ASCII , 80=0dB, 99=---(MIN) MV80<CR>
CV FL UP CHANNEL VOLUME UP/DOWN , direct change to **dB CVFL UP<CR>
FL DOWN ---FRONT Lch CVFL DOWN<CR>
FL ** **:38 to 62 by ASCII , 50=0dB CVFL 50<CR>
FR UP CVFR UP<CR>
FR DOWN ---FRONT Rch CVFR DOWN<CR>
FR ** **:38 to 62 by ASCII , 50=0dB CVFR 50<CR>
C UP CVC UP<CR>
C DOWN ---CENTERch CVC DOWN<CR>
C ** **:38 to 62 by ASCII , 50=0dB CVC 50<CR>
SW UP CVSW UP<CR>
SW DOWN ---SUBWOOFERch CVSW DOWN<CR>
SW ** **:00,38 to 62 by ASCII , 50=0dB,00=OFF CVSW 50<CR>
SL UP CVSL UP<CR>
SL DOWN ---SURROUND Lch CVSL DOWN<CR>
SL ** **:38 to 62 by ASCII , 50=0dB CVSL 50<CR>
SR UP CVSR UP<CR>
SR DOWN ---SURROUND Rch CVSR DOWN<CR>
SR ** **:38 to 62 by ASCII , 50=0dB CVSR 50<CR>
SBL UP ---SURROUND BACK Lch (SBch 2SP) CVSBL UP<CR>
SBL DOWN CVSBL DOWN<CR>
SBL ** **:38 to 62 by ASCII , 50=0dB CVSBL 50<CR>
SBR UP ---SURROUND BACK Rch (SBch 2SP) CVSBR UP<CR>
SBR DOWN CVSBR DOWN<CR>
SBR ** **:38 to 62 by ASCII , 50=0dB CVSBR 50<CR>
COMMAND PARAMETER
MV , CV COMMAND : "*" parameter uses two or three ASCII characters. (see page4 J) section)
function example
- 7 -
Page 8
COMMAND PARAMETER
function example
CV SB UP ---SURROUND BACKch (SBch 1SP) CVSB UP<CR>
SB DOWN CVSB DOWN<CR>
SB ** **:00 to 99 by ASCII , 50=0dB CVSB 50<CR>
MU ON OUTPUT MUTE ON/OFF change MUON<CR>
OFF MUOFF<CR>
SI PHONO Select INPUT source SIPHONO<CR>
CD SICD<CR>
TUNER SITUNER<CR>
DVD SIDVD<CR>
VDP SIVDP<CR>
TV SITV<CR>
DBS
SIDBS<CR>
VCR-1 SIVCR-1<CR>
VCR-2 SIVCR-2<CR>
VCR-3 SIVCR-3<CR>
V.AUX SIV.AUX<CR>
CDR/TAPE SICDR/TAPE<CR>
ZM ON MAIN-ZONE ON/OFF change at AVR-4806 ZMON<CR>
OFF ZMOFF<CR>
Z2 PHONO MULTI ZONE-2 mode set , and select source at AVR-4806 Z2PHONO<CR>
| ---The name of PARAMETER is |
CDR/TAPE
the same as that of the time of SI COMMAND.
Z2CDR/TAPE
SOURCE MULTI ZONE-2 mode cancel at AVR-4806 Z2SOURCE<CR>
UP MULTI ZONE-2 VOLUME UP/DOWN , direct change to **dB Z2UP<CR>
DOWN at AVR-4806 Z2DOWN<CR>
** **:10 to 99 by ASCII , 80=0dB, 99=---(MIN) Z280<CR>
ON MULTI ZONE-2 ON/OFF change at AVR-4806 Z2ON<CR>
OFF Z2OFF<CR>
Z2MU ON
OFF
ZONE2 OUTPUT MUTE ON/OFF change Z2MUON<CR>
Z2MUOFF<CR>
CV , Z2 COMMAND : "*" parameter uses two ASCII characters. (see page4 J) section)
- 8 -
Page 9
SR PHONO REC SELECT mode set , and select source SRPHONO<CR>
| ---The name of PARAMETER is |
SOURCE REC SELECT mode cancel SRSOURCE<CR>
SV DVD VIDEO SELECT mode set , and select source SVDVD<CR>
VDP SVVDP<CR>
TV SVTV<CR>
VCR-1 SVVCR-1<CR>
VCR-2 SVVCR-2<CR>
VCR-3 SVVCR-3<CR>
V.AUX SVV.AUX<CR>
SOURCE VIDEO SELECT mode cancel SVSOURCE<CR>
SD AUTO set DIGITAL INPUT AUTO mode SDAUTO<CR>
PCM set DIGITAL INPUT force PCM mode SDPCM<CR>
DTS set DIGITAL INPUT force DTS mode SDDTS<CR>
RF ---Invalid at AVR-4806 SDRF<CR>
ANALOG set force ANALOG INPUT mode SDANALOG<CR>
EXT.IN-1 ---Set EXT.IN mode at AVR-4806 SDEXT.IN-1<CR>
EXT.IN-2 ---Invalid at AVR-4806 SDEXT.IN-2<CR>
COMMAND PARAMETER
Z3 PHONO
|
CDR/TAPE
SOURCE
UP
DOWN
**
ON
OFF
Z3MU ON
OFF
CDR/TAPE
DBS SVDBS<CR>
Z3 COMMAND : "*" parameter uses two ASCII characters. (see page4 J) section)
MULTI ZONE-3 mode set , and select source at AVR-4806
---The name of PARAMETER is
the same as that of the time of SI COMMAND.
MULTI ZONE-3 mode cancel
MULTI ZONE-3 VOLUME UP/DOWN , direct change to **dB
**:10 to 99 by ASCII , 80=0dB, 99=---(MIN)
MULTI ZONE-3 ON/OFF change at AVR-4806
ZONE3 OUTPUT MUTE ON/OFF change
the same as that of the time of SI COMMAND.
function example
- 9 -
Z3PHONO<CR>
|
Z3CDR/TAPE<CR>
Z3SOURCE<CR>
Z3UP<CR>
Z3DOWN<CR>
Z380<CR>
Z3ON<CR>
Z3OFF<CR>
Z3MUON<CR>
Z3MUOFF<CR>
SRCDR/TAPE<CR>
Page 10
EVENT PARAMETER
function example
MS DIRECT SURROUND mode set MSDIRECT<CR>
PURE DIRECT MSPURE DIRECT<CR>
STEREO MSSTEREO<CR>
MULTI CH IN ---This is received as "SATNDARD". MSMULTI CH IN<CR>
MULTI CH DIRECT MSMULTI CH DIRECT<CR>
MULTI CH PURE D MSMULTI CH PURE D<CR>
DOLBY PRO LOGIC All are received as "STANDARD" , MSDOLBY PRO LOGIC<CR>
DOLBY PL2
the surround mode which changed return as EVENT.
MSDOLBY PL2<CR>
DOLBY PL2x MSDOLBY PL2X<CR>
DOLBY DIGITAL MSDOLBY DIGITAL<CR>
DOLBY D EX MSDOLBY D EX<CR>
DTS NEO:6 All are received as "DTS SURROUND" , MSDTS NEO:6<CR>
DTS SURROUND MSDTS SURROUND<CR>
DTS ES DSCRT6.1 MSDTS ES DSCRT6.1<CR>
DTS ES MTRX6.1 MSDTS ES MTRX6.1<CR>
DOLBY H/P
DTS+DOLBY H/P
HOME THX CINEMA
All are received as "THX SURROUND" ,
THX5.1 the surround mode which changed return as EVENT. MSTHX5.1<CR>
THX U2 CINEMA
THX MUSIC MODE
THX GAMES MODE MSTHX GAMES MODE<CR>
THX6.1
THX SURROUND EX
MSDOLBY H/P<CR>
MSDTS+DOLBY H/P<CR>
MSHOME THX CINEMA<CR>
MSTHX U2 CINEMA<CR>
MSTHX MUSIC MODE<CR>
MSTHX6.1<CR>
MSTHX SURROUND EX<CR>
WIDE SCREEN MSWIDE SCREEN<CR>
5CH STEREO Both are received as "5CH/7CH/9CH STEREO" , MS5CH STEREO<CR>
7CH STEREO
9CH STEREO MS9CH STEREO<CR>
the surround mode which changed return as EVENT.
MS7CH STEREO<CR>
SUPER STADIUM MSSUPER STADIUM<CR>
ROCK ARENA MSROCK ARENA<CR>
JAZZ CLUB MSJAZZ CLUB<CR>
CLASSIC CONCERT MSCLASSIC CONCERT<CR>
MONO MOVIE MSMONO MOVIE<CR>
MATRIX MSMATRIX<CR>
VIDEO GAME MSVIDEO GAME<CR>
- 10 -
Page 11
EVENT PARAMETER
function example
MS VIRTUAL ---Invalid at AVR-4806 model MSVIRTUAL<CR>
MPEG2 AAC ---Invalid at AVR model MSMPEG2 AAC<CR>
AAC+DOLBY EX ---Invalid at AVR model MSAAC+DOLBY EX<CR>
USER1 MSUSER1<CR>
USER2 MSUSER2<CR>
USER3 MSUSER3<CR>
PS TONE DEFEAT ON PARAMETER setting PSTONE DEFEAT ON<CR>
TONE DEFEAT OFF TONE DEFEAT ON/OFF PSTONE DEFEAT OFF<CR>
SB:MTRX ON SURROUND BACK SP MODE set PSSB:MTRX ON<CR>
SB:NON MTRX ---MTRX ON = SURR.EX ON = DSCRT ON PSSB:NON MTRX<CR>
SB:PL2xCINEMA (@THX) (@ES DSCRT) PSSB:PL2X CINEMA<CR>
SB:PL2xMUSIC PSSB:PL2X MUSIC<CR>
SB:OFF PSSB:OFF<CR>
CINEMA EQ.ON CINEMA EQ. ON/OFF PSCINEMA EQ.ON<CR>
CINEMA EQ.OFF PSCINEMA EQ.OFF<CR>
MODE : MUSIC CINEMA / MUSIC / GAME / PL mode change PSMODE:MUSIC<CR>
MODE : CINEMA (This parameter can change DOLBY PL2,PL2x,NEO:6 mode.) PSMODE:CINEMA<CR>
MODE : GAME
---SB=ON：PL2x mode / SB=OFF：PL2 mode
PSMODE:GAME<CR>
MODE : PRO LOGIC --- GAME can change DOLBY PL2 & PL2x mode PSMODE:PRO LOGIC<CR>
--- PL can change ONLY DOLBY PL2 mode
ROOM EQ:AUDYSSEY
ROOM EQ mode direct change
PSROOM EQ:AUDYSSEY<CR>
ROOM EQ:FRONT PSROOM EQ:FRONT<CR>
ROOM EQ:FLAT PSROOM EQ:FLAT<CR>
ROOM EQ:MANUAL PSROOM EQ:MANUAL<CR>
ROOM EQ:OFF PSROOM EQ:OFF<CR>
DELAY UP
DELAY DOWN
DELAY ***
AUDIO DELAY UP/DOWN , direct change to ***dB
***:000 to 999 by ASCII , 000=0ms, 200=200ms
---AVR-4806 can be operated from 0 to 200
PSDELAY UP<CR>
PSDELAY DOWN<CR>
PSDELAY 200<CR>
- 11 -
Page 12
EVENT PARAMETER
function example
TF UP TUNER Frequency UP/DOWN , direct change TFUP<CR> *
DOWN TFDOWN<CR> *
****** (6 digits) --- ****.** kHz at AM band (>050000 is AM.)
****.** MHz at FM band (<050000 is FM.)
XM***
--- *** at XM mode TFXM001<CR>
(channel No.)
TF105000<CR>
(1050.00kHz at AM)
(channel 1 at XM)
TP UP TUNER PRESET CH UP/DOWN , direct change to No.** TPUP<CR>
DOWN TPDOWN<CR>
**(PRESET No.) TPA1<CR>
(PRESET No.”A1”)
TM TUNER BAND , MODE Select
AM ---Band set to AM TMAM<CR>
FM ---Band set to FM TMFM<CR>
XM ---Band set to XM TMXM<CR>
AUTO ---Tuning mode set to AUTO mode TMAUTO<CR> *
MANUAL ---Tuning mode set to MANUAL mode TMMANUAL<CR> *
TF, TP, TM COMMAND : '*' parameters can NOT operate when INPUT source isn’t TUNER.
- 12 -
Page 13
EVENT(or RESPONSE) and PARAMETER list
PW ON POWER ON/STANDBY change PWON<CR>
STANDBY PWSTANDBY<CR>
MV ** MASTER VOLUME change , **:00 to 99 by ASCII MV80<CR>
98 = +18dB(MAX)
80 = 0dB
00 = -80dB
99 = ---(MIN)
CV FL ** CHANNEL VOLUME change , **:00,38 to 62 by ASCII CVFL 50<CR>
FR ** 62 = +12dB(MAX) CVFR 50<CR>
C ** 50 = 0dB CVC 50<CR>
SW ** 38 = -12dB(MIN) CVSW 50<CR>
SL ** 00 = OFF (define ONLY SWch in DIRECT mode.) CVSL 50<CR>
SR ** CVSR 50<CR>
SBL ** (at SBch 2SP) CVSBL 50<CR>
SBR ** (at SBch 2SP) CVSBR 50<CR>
SB ** (at SBch 1SP) CVSB 50<CR>
MU ON OUTPUT MUTE ON/OFF change MUON<CR>
OFF MUOFF<CR>
SI PHONO INPUT source change SIPHONO<CR>
CD SICD<CR>
TUNER SITUNER<CR>
DVD SIDVD<CR>
VDP SIVDP<CR>
TV SITV<CR>
VCR-1 SIVCR-1<CR>
VCR-2 SIVCR-2<CR>
VCR-3 SIVCR-3<CR>
V.AUX SIV.AUX<CR>
EVENT PARAMETER
DBS SIDBS<CR>
CDR/TAPE SICDR/TAPE<CR>
*RES. : NOT returns '*' parameters as RESPONSE.
The PARAMETER of MV, CV EVENT : Uses two or three ASCII characters. (see page4 J) section)
function example *RES.
- 13 -
Page 14
ZM ON MAIN-ZONE ON/OFF change ZMON<CR>
OFF ZMOFF<CR>
Z2 PHONO MULTI ZONE-2 source change Z2PHONO<CR>
| ---The name of PARAMETER is |
SOURCE MULTI ZONE-2 mode cancel Z2SOURCE<CR>
** MULTI ZONE-2 VOLUME change , **:10 to 99 by ASCII Z280<CR>
98 = +18dB(MAX)
80 = 0dB
10 = -70dB
99 = ---(MIN)
ON MULTI ZONE-2 ON/OFF change Z2ON<CR>
OFF Z2OFF<CR>
SR PHONO REC SELECT source change SRPHONO<CR>
| ---The name of PARAMETER is |
SOURCE REC SELECT mode cancel SRSOURCE<CR>
EVENT PARAMETER
CDR/TAPE
Z2MU ON
OFF
Z3 PHONO
|
CD/TAPE
SOURCE
**
ON
OFF
Z3MU ON
OFF
CD/TAPE
The PARAMETER of Z2, Z3 EVENT : Uses two ASCII characters. (see page4 J) section)
ZONE2 OUTPUT MUTE ON/OFF change
MULTI ZONE-3 source change
---The name of PARAMETER is
MULTI ZONE-3 mode cancel
MULTI ZONE-3 VOLUME change , **:10 to 99 by ASCII
98 = +18dB(MAX)
80 = 0dB
10 = -70dB
99 = ---(MIN)
MULTI ZONE-3 ON/OFF change
ZONE3 OUTPUT MUTE ON/OFF change
the same as that of the time of SI COMMAND.
the same as that of the time of SI COMMAND.
the same as that of the time of SI COMMAND.
function example *RES.
Z2CDR/TAPE<CR>
Z2MUON<CR>
Z2MUOFF<CR>
Z3PHONO<CR>
|
Z3CDR/TAPE<CR>
Z3SOURCE<CR>
Z380<CR>
Z3ON<CR>
Z3OFF<CR>
Z3MUON<CR>
Z3MUOFF<CR>
SRCDR/TAPE<CR>
- 14 -
Page 15
EVENT PARAMETER
function example *RES.
TF ****** (6 digits) TUNER Frequency change TF105000<CR>
--- ****.** kHz at AM band (1050.00kHz at AM)
****.** MHz at FM band
XM***
(channel No.)
--- *** at XM mode TFXM001<CR>
(channel 1 at XM)
TP **(PRESET No.) TUNER PRESET change to No.** TPA1<CR>
(PRESET No.”A1”)
TM TUNER BAND , MODE change
AM ---Band set to AM TMAM<CR>
FM ---Band set to FM TMFM<CR>
XM ---Band set to XM TMXM<CR>
AUTO ---Tuning mode set to AUTO mode TMAUTO<CR> *
MANUAL ---Tuning mode set to MANUAL mode TMMANUAL<CR> *
*RES. : NOT returns '*' parameters as RESPONSE.
- 15 -
Page 16
EVENT PARAMETER
function example *RES.
MS DIRECT SURROUND mode change MSDIRECT<CR>
PURE DIRECT MSPURE DIRECT<CR>
STEREO MSSTEREO<CR>
MULTI CH IN MSMULTI CH IN<CR>
MULTI CH IN
MSM CH IN+PL2X C<CR>
+PL2x CINEMA
MULTI CH IN
MSM CH IN+PL2X M<CR>
+PL2x MUSIC
MULTI CH DIRECT MSMULTI CH DIRECT<CR>
MULTI CH DIRECT
MSM CH DRCT+PL2X C <CR>
+PL2x CINEMA
MULTI CH DIRECT
MSM CH DRCT+PL2X M <CR>
+PL2x MUSIC
MULTI CH PURE D MSMULTI CH PURE D<CR>
MULTI CH PURE D
MSM CH PURE D+PL2X C <CR>
+PL2x CINEMA
MULTI CH PURE D
MSM CH PURE D+PL2X M <CR>
+PL2x MUSIC
DOLBY PRO LOGIC MSDOLBY PRO LOGIC<CR>
DOLBY PL2 CINEMA MSDOLBY PL2 C<CR>
DOLBY PL2 MUSIC MSDOLBY PL2 M<CR>
DOLBY PL2 GAME MSDOLBY PL2 G<CR>
DOLBY PL2x CINEMA MSDOLBY PL2X C<CR>
DOLBY PL2x MUSIC MSDOLBY PL2X M<CR>
DOLBY PL2x GAME MSDOLBY PL2X G<CR>
DOLBY DIGITAL MSDOLBY DIGITAL<CR>
DOLBY D EX MSDOLBY D EX<CR>
DOLBY D
MSDOLBY D+PL2X C<CR>
+PL2x CINEMA
DOLBY D
MSDOLBY D+PL2X M<CR>
+PL2x MUSIC
- 16 -
Page 17
EVENT PARAMETER
function example *RES.
DTS NEO:6 CINEMA MSDTS NEO:6 C<CR>
DTS NEO:6 MUSIC MSDTS NEO:6 M<CR>
DTS SURROUND MSDTS SURROUND<CR>
DTS ES DSCRT6.1 MSDTS ES DSCRT6.1<CR>
DTS ES MTRX6.1 MSDTS ES MTRX6.1<CR>
DTS+PL2x CINEMA MSDTS+PL2X C<CR>
DTS+PL2x MUSIC MSDTS+PL2X M<CR>
DOLBY H/P MSDOLBY H/P<CR>
DTS+DOLBY H/P MSDTS+DOLBY H/P<CR>
PL2x C+THX MSPL2X C+THX
PL2 C+THX MSPL2 C+THX
PL+THX MSPL+THX
NEO:6 C+THX MSNEO:6 C+THX
THX5.1 MSTHX5.1<CR>
THX U2 CINEMA MSTHX U2 CINEMA<CR>
THX MUSIC MODE MSTHX MUSIC MODE<CR>
THX GAMES MODE MSTHX GAMES MODE<CR>
THX6.1 MSTHX6.1<CR>
THX SURROUND EX MSTHX SURROUND EX<CR>
WIDE SCREEN MSWIDE SCREEN<CR>
5CH STEREO MS5CH STEREO<CR>
7CH STEREO MS7CH STEREO<CR>
9CH STEREO ---Invalid at AVR-4806 model MS9CH STEREO<CR>
SUPER STADIUM MSSUPER STADIUM<CR>
ROCK ARENA MSROCK ARENA<CR>
JAZZ CLUB MSJAZZ CLUB<CR>
CLASSIC CONCERT MSCLASSIC CONCERT<CR>
MONO MOVIE MSMONO MOVIE<CR>
MATRIX MSMATRIX<CR>
VIDEO GAME MSVIDEO GAME<CR>
- 17 -
Page 18
EVENT PARAMETER
MS VIRTUAL ---Invalid at AVR-4806 model MSVIRTUAL<CR>
function example *RES.
MPEG2 AAC ---Invalid at AVR model MSMPEG2 AAC<CR>
AAC+DOLBY EX ---Invalid at AVR model MSAAC+DOLBY EX<CR>
AAC+PL2x CINEMA ---Invalid at AVR model MSAAC+PL2X C<CR>
AAC+PL2x MUSIC ---Invalid at AVR model MSAAC+PL2X M<CR>
PS
USER1 MSUSER1<CR>
USER2 MSUSER2<CR>
USER3 MSUSER3<CR>
ROOM EQ:AUDYSSEY
ROOM EQ mode direct change
PSROOM EQ:AUDYSSEY<CR>
ROOM EQ:FRONT PSROOM EQ:FRONT<CR>
ROOM EQ:FLAT PSROOM EQ:FLAT<CR>
ROOM EQ:MANUAL PSROOM EQ:MANUAL<CR>
ROOM EQ:OFF PSROOM EQ:OFF<CR>
DELAY ***
AUDIO DELAY change, ***:000 to 999 by ASCII
---AVR-4806：200=200ms（MAX）
100=100ms, 000=0ms
PSDELAY 200<CR>
- 18 -
Loading...