Denon AVC-1803, AVR-3803 Schematic

For U.S.A., Canada, Europe, Asia, China, Hong Kong, Taiwan R.O.C., Korea & Japan model

SERVICE MANUAL

MODEL

AV SURROUND RECEIVER/AMPLIFIER

REMOTE

SURROUND

SIGNAL

SENSOR

BACK CH

OUTPUT

DIGITAL

INPUT

SIGNAL

ON / STANDBY

AUTO

DTS

PCM

DETECT

AVR-3803 AVC-3570

VOLUME LEVEL

AVR-3803/1083 AVC-3570

 Some illustrations using in this service manual are

slightly different from the actual set.

16-11, YUSHIMA 3-CHOME, BUNKYOU-KU, TOKYO 113-0034 JAPAN

Telephone: 03 (3837) 5321

X0155 NC 0211

AVR-3803/1083/AVC-3570

SAFETY PRECAUTIONS

The following check should be performed for the continued protection of the customer and service technician.

LEAKAGE CURRENT CHECK

Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the unit is defective.

500V

(1)

(2)

(1)

(2)

WIRE ARRANGEMENT

If wire bundles are untied or moved to perform adjustment or parts replacement etc.,be sure to rearrange them neatly as they were originally bundled or placed afterward. Otherwise, incorrect arrangement can be a cause of noise generation.

Wire arrangement viewed from the top

AVR-3803/1083/AVC-3570

DISASSEMBLY

(Follow the procedure below in reverse order when reassembling)

AVR-3803/1083/AVC-3570

1. Top Cover

Remove 3 screws on the rear and 6 screws on both sides to detach the Top Cover as shown in the arrow direction.

Top Cover

2. Front Panel

(1) Remove 7 screws from the top and bottom edges of

the Front Panel.

(2) Release 4 top and bottom Hooks, then detach the

Front Panel as shown in the arrow direction.

1. Top Cover

3 6 Top Cover

2. Front Panel

(1) Front Panel

(2) Front Panel 4 Hook

Front Panel

Hook

Front Panel

Hook

3. Inner Panel

Pull out the Inner Panel in the arrow direction after removing 3 screws.

Inner Panel

Hook

3. Inner Panel

3 Inner Panel

Hook

AVR-3803/1083/AVC-3570

4. Inner Panel Ass'y

(1) Remove 3 round and 1 square knobs, and unscrew 4

nuts.

(2) Remove 14 screws fixing each P.W.B.

Nut

Round Knob

Square Knob

Nut

Round Knob

5. Amp Connect Unit/Component Video Unit

(1) Remove 9 screws to detach Pre-out Unit and

Component Video Unit.

(2) Take off the Amp Connect Unit as shown in the arrow

direction after removing 1 screw.

Pre-out Unit

Amp Connect Unit

4. Inner Panel Ass'y

(1) Round Knob 3

Nut

(2) PWB 14

Square Knob 1 4

5. Amp Connect Unit/Component Video Unit

(1)

(2) 1 Amp Connect Unit

Component Video Unit

12 Pre-out Unit Component Video

Unit

6. Regulator Unit

Take off the Regulator Unit as shown in the arrow direction after removing 11 screws.

Regulator Unit

6. Regulator Unit

11 Regulator Unit

AVR-3803/1083/AVC-3570

7. Component-Video/S-Video / C-video / Audio in / Ext-in VR / Digital/Remote I/O / AM FM Tuner Unit

(1) Remove 60 screws to detach the Rear Panel.

(2) Take off the objective P.W.B. upward.

Rear Panel

7. Component-Video/S-Video / C-video / Audio in / Ext-in VR / Digital/Remote I/O

(1) 61 Rear Panel

(2) P.W.B.

8. How to Check Power / Control Unit with Power-on

(1) Remove 17 screws fixing to the Chassis.

(2) Pull up the Unit to separate from the Chassis.

8. Powr/Control Unit

(1) Chassis 17

(2) Chassis

Chassis

CAUTION IN SERVICING

AVR-3803/1083/AVC-3570



 Initializing AV SURROUND RECEIVER



AV SURROUND RECEIVER initialization should be performed when the µcom, peripheral parts of µcom, and DSP P.W.B. are replaced.

1. Switch off the unit and remove the AC cord from the

wall outlet.

2. Hold the following PURE DIRECT button and ZONE

2 button, and plug the AC cord into the outlet.

3. Check that the entire display is flashing with an

interval of about 1 second, and release your fingers from the 2 buttons and the microprocessor will be initialized.

REMOTE

SIGNAL

SENSOR

DIGITAL

INPUT

ON / STANDBY

AUTO

DTS

PCM



 AV



DSP

2. PURE DIRECT VIDEO OFF

3. 1 2

SURROUND

BACK CH

OUTPUT

SIGNAL DETECT

VOLUME LEVEL

1 2

Note:  If step 3 does not work, start over from step 1.

 All user settings will be lost and this factory

setting will be recovered when this initialization mode. So make sure to memorize your setting for restoring after the initialization.

:  3 1



ADJUSTMENT

Audio Section

Idling Current (1U-3469-1)

Required measurement equipment: DC Voltmeter

Preparation

(1) Avoid direct blow from an air conditioner or an electric

fan, and adjust the unit at normal room tempereture 15 °C ~ 30 °C (59 °F ~ 86 °F).

(2) Presetting

 POWER (Power sourse switch) OFF  SPEAKER (Speaker terminal) No load

(Do not connect speaker, dummy resistor, etc.)

Adjustment

(1) Remove top cover and set VR101, VR102, VR201,

VR301, VR302, VR401, VR402, on 1U-3469-1 (Power Unit) at fully counterclockwise (

(2) Connect DC Voltmeter to test points (FRONT-Lch:

TP301 CENTER ch: TP301

2 pin, FRONT-Rch: TP101 5 6 pin,

3 4

pin, SURROUND-Lch: TP101

4 pin, SURROUND-Rch: TP101 1 2 pin,

SURROUND BACK-Lch: TP301

BACK-Rch: TP301

6 pin).

(3) Connect power cord to AC Line, and turn power switch

"ON".

(4) Presetting.

MASTER VOLUME : "---" counterclockwise ( MODE : 7CH STEREO FUNCTION : CD

(5) Allow 2 minutes, and turn VR101 clockwise ( ) to

adjust the TEST POINT voltage to 6.5 mV ±0.5 mV DC.

(6) After 10 minutes from preset, turn VR101 to set the

voltage to 8 mV ±0.5 mV DC.

(7) Adjust the Variable Resistors of other channels in the

same way.

(8) After 5 minutes from (6), turn VR101 to set the voltage to

8 mV ±0.5 mV DC.

(9) Adjust the Variable Resistors of other channels in the

same way.

8 pin, SURROUND

min.)

AVR-3803/1083/AVC-3570

(1U-3469-1)

: DC Voltmeter

(1)

15 30

(2)

 OFF 

( )

(1) 1U-3469-1

VR101, VR102, VR201, VR301, VR302, VR401, VR402

( )

(2) (FRONT-Lch: TP301 1 2 pin, FRONT-

Rch: TP101 SURROUND-Lch: TP101 TP101 pin, SURROUND BACK-Rch: TP301 5 6 pin) DC Voltmeter

(3) AC100V 95 105V

(4) ON

 MASTER VOLUME

( )

 SPEAKER

(5) 2

(6)

(7)

(8) (6) 5 VR101

6 pin, CENTER ch: TP301 3 4 pin,

4 pin, SURROUND-Rch:

2 pin, SURROUND BACK-Lch: TP301 7

"ON"

MODE : 7CH STEREO FUNCTION : CD

VR101 ( )

6.5mV ±0.5mV DC

10 VR101

8mV ±0.5mV DC

(9)

8mV ±0.5mV DC

DC Voltmeter

SR ch

VR302

SL ch

VR301

FR ch

VR102

FL ch

VR101

C ch

VR201

SBR ch

VR402

SR ch

SL ch

FR ch

FL ch

C ch

SBR ch

SBL ch

AVR-3803/1083/AVC-3570

TP101

TP301

SBL ch

VR401

Audio Section

Video Section

Component Video Level Adjustment

Required measurement equipment etc: Oscilloscope, DVD VIDEO PLAYER (ex: DVD-1500) Test Disc: DVD T-S01

Preparation

(1) Avoid direct blow from an air conditioner or an electric

fan, and adjust the unit at normal room temperature 15 °C ~ 30 °C (59 °F ~ 86 °F).

(2) Playback the color-bar 75% of the Test Disc (Title 12)

using the DVD Video Player, and check that Y and C levels of the S terminal output are within the specified output levels. If they are out of the specified levels, adjust with the variable resister inside of the unit.

(3) Presetting

 POWER (Power source switch) OFF  SPEAKER (Speaker terminal) No load

(Do not connect speaker, dummy resistor, etc.)

 DVD (Video terminal) No input

Adjustment

(1) Remove top cover and set VR101, VR102, VR103 on

1U-3475-1 (Convert Unit) at fully counterclockwise (

(2) Connect a pin-plug terminated with 75-ohms to Y(Cb,

Cr) of the Component Video Monitor Output, and hook up the Oscilloscope's probe to both ends of the pin-plug.

(3) Connect S terminal output of the DVD Player with the

DVD input terminal of the Receiver.

(4) Connect power cord to AC Line, and turn power switch

"ON".

(5) Presetting

 FUNCTION: DVD

Playback the color-bar 75% of the Test Disc (Title 12)



(6) Turn VR101 clockwise ( ) to adjust the

COMPONENT VideoY voltage (except H.Sync) to 714 ±50 mVp-p. (Refer to Fig.1)

(7) Adjust the Variable Resistors of Cb: VR102 and Cr:

VR103 in the same way. (Refer to Fig. 2, 3)

Cb,Cr: 486±50 mVp-p. (U.S.A. & Canada model)

525±50 mVp-p. (Others)

AVR-3803/1083/AVC-3570

: Oscilloscope, DVD VIDEO PLAYER

: DVD-1500)

(

: DVD T-S01

(1)

15 30

(2) DVD VIDEO PLAYER

75 (Title12) S Y C

(3)

 OFF 

( )

 DVD

(1) 1U-3475-1

VR101, VR102, VR103 ( )

(2) Y(Cb, Cr) 75

Oscilloscope

(3) DVD VIDEO PLAYER S DVD

(4)

"ON"

(5) ON

 FUNCTION DVD

 75 (Title12)

(6) VR101 ( )

Y(H.Sync ) (Fig.1 )

714mV ±50mVp-p

(7)

Cb: VR102 Cr: VR103

(Fig.2 3 )

Cb,Cr: 525±50 mVp-p.

Oscilloscope

AVR-3803/1083/AVC-3570

VR103Cr

VR102

VR101

Video Section

Component Video Y

AVR-3803/1083/AVC-3570

Volts

IRE:FLT

100.0

0.5

0.0

0.5

-20.0 -10.0 0.0

Volts

IRE:FLT

0.5

50.0

Y-Signal

714±50mV

p-p

10.0

20.0 30.0

Fig.1 Component Video Y signal

40.0 50.0 60.0

486±50mV (U.S.A. & Canada model)

p-p

525±50mV (Others)

p-p

0.0

-0.5

Volts

0.5

0.0

-50.0

0.0

IRE:FLT

50.0

0.0

-50.0

20.0

Fig.2 Cb signal

40.0

60.0

486±50mV (U.S.A. & Canada model) 525±50mV (Others)

80.0

p-p

-0.5

0.0

20.0

Fig.3 Cr signal

40.0

60.0

80.0

BLOCK DIAGRAMS (1/2)

AVR-3803/AVR-1083/AVC-3570

BLOCK DIAGRAMS (2/2)

AVR-3803/AVR-1083/AVC-3570

LEVEL DIAGRAMS (1/5)

AVR-3803/AVR-1083/AVC-3570

AUDIO SECTION (1/2)

LEVEL DIAGRAMS (2/5)

AVR-3803/AVR-1083/AVC-3570

AUDIO SECTION (2/2)

LEVEL DIAGRAMS (3/5)

AVR-3803/AVR-1083/AVC-3570

VIDEO SECTION (1/3)

LEVEL DIAGRAMS (4/5)

AVR-3803/AVR-1083/AVC-3570

VIDEO SECTION (2/3)

LEVEL DIAGRAMS (5/5)

AVR-3803/AVR-1083/AVC-3570

VIDEO SECTION (3/3)

CLOCK FLOW & WAVE FORM IN DIGITAL BLOCK

㽳㽳

㽴㽴

㽳㽳㽳㽳

Wave form

CH1: D-DATA

(IC510 (5) )

AVR-3803/1083/AVC-3570

CH1: DATA

CH2: fs

CH3: 64fs

CH1: DATA

㽲㽲㽲㽲㽳

INPUT

INPUTINPUT

SELECTOR

SELECTOR BUFFER

SELECTORSELECTOR

IC5㪈3

IC5㪈3 IC522

IC5㪈3IC5㪈3

INPUT

INPUTINPUT

COAXIAL-㪈

COAXIAL-㪈 (3) RDATA(2㪈)(㪈㪈)- -(9) (64)SD0A

COAXIAL-㪈COAXIAL-㪈 COAXIAL-2

COAXIAL-2 (2) SLRCK(23) (㪈3)- -(7) (38)SFS2 (㪈)fs

COAXIAL-2COAXIAL-2 OPTICAL-㪈

OPTICAL-㪈 (㪈2) (5) (4)RX2 (39)SFS3 (2)64fs SLch

OPTICAL-㪈OPTICAL-㪈 OPTICAL-2

OPTICAL-2 (㪈3) SBCK(22) (㪈5)- -(5) (7)SCLK2 (3)DATA FLch

OPTICAL-2OPTICAL-2 OPTICAL-3

OPTICAL-3 (㪈4) (㪈7)- -(3) (54)SCLK3 (5)256fs

OPTICAL-3OPTICAL-3 OPTICAL-4

OPTICAL-4 (㪈5) RMCK(㪈6) (4)- -(㪈6)

OPTICAL-4OPTICAL-4 OPTICAL-5

OPTICAL-5 (㪈) (2)- -(㪈8) (50)SCLK0

OPTICAL-5OPTICAL-5

SN74HC

SN74HC SN74LV

SN74HC SN74HC

㪈5㪈APW

㪈5㪈APW 244APW

㪈5㪈APW㪈5㪈APW

OUTPUT

OUTPUT (52)SFS㪈 (㪈)fs

OUTPUTOUTPUT

SELECTOR

SELECTOR ADIN(24) SD2A(37) (2)64fs FRch

SELECTORSELECTOR

DIR

DIR DSP

DIRDIR

IC520

IC520IC520

LC89057W

LC89057WLC89057W

DATA

64fs

256fs

RBCK(㪈7) (6)- -(㪈4) (2㪈)SCLK㪈

RLRCK(20) (8)- -(㪈2) (20)SFS0

64fs

BUFFER

BUFFERBUFFER

IC522

IC522IC522

SN74LV

SN74LVSN74LV 244APW

244APW244APW

㽳㽴

DSP

DSPDSP

IC80㪈

IC80㪈IC80㪈

ADSST-MEL㪈00

ADSST-MEL㪈00ADSST-MEL㪈00

㽴

D/A CONVERTER

A CONVERTERD/A CONVERTER

IC523

IC523IC523

PCM㪈79㪈

PCM㪈79㪈PCM㪈79㪈

IC524

IC524IC524

PCM㪈79㪈

PCM㪈79㪈PCM㪈79㪈

(29)XIN SD2B(22) (3)DATA SRch

IC5㪈4

IC5㪈4 SD3A(23) (5)256fs

IC5㪈4IC5㪈4

SN74HC

SN74HC SN74HC

㪈5㪈APW

㪈5㪈APW㪈5㪈APW

(3) (㪈5)DATA (2) 24.576MHz

(㪈2) IC52㪈 (㪈3) (5) FXC0 (㪈4) -03 (㪈5) (3) (5)256fs (㪈)

OUTPUT

OUTPUTOUTPUT

OPTICAL-4

OPTICAL-4OPTICAL-4 OPTICAL-5

OPTICAL-5 (㪈)fs

OPTICAL-5OPTICAL-5

24.576MHz (㪈6)BCK

24.576MHz24.576MHz

IC52㪈 (㪈7)LRCK (㪈)fs

IC52㪈IC52㪈

FXC0 SYSCK(㪈8) (2)64fs SBLch

FXC0FXC0

-03 (3)DATA Cch

-03-03

IC5㪈9

IC5㪈9IC5㪈9

PCM㪈804

PCM㪈804PCM㪈804

A/D CONVERTER

A/D CONVERTER IC526

A/D CONVERTERA/D CONVERTER

SD3B (8)

IC525

IC525IC525

PCM㪈79㪈

PCM㪈79㪈PCM㪈79㪈

IC526

IC526IC526

PCM㪈79㪈

PCM㪈79㪈PCM㪈79㪈

(2)64fs SWch (3)DATA SBRch (5)256fs

CH2: fs

CH3: 64fs

CH4: 256fs

CHECK WITH TEST MODE

µµ

µcom/DSP Error Display Mode

µµ

AVR-3803/1083/AVC-3570

DSP

1. Operation Spec

µµ

µcom version display mode:

µµ

When the following conditions are satisfied at its starting state, error information is displayed before version information.

Starting method (same as

While pressing 2 buttons, "DIMMER (S11)" and "SURROUND BACK (S14)", plug the AC cord to the wall outlet.

Then, press "STATUS" button to display the following information on the FL Display.

µµ

µcom version display):

µµ

2. Display Order

Error information

Main-µcom version information Sub-µcom version information DSP version information

3. Display

2 3

Any one of the following list is displayed, in the priority of

Condition State Display

Sub-µcom NG No response from Sub-µcom " "

DIR NG No response from DIR " "

DSP NG When DSP boot, executing DSP reset

makes no change to BUSY port "L".

No change to BUSY port "L" before issuing DSP command. " "

When DSP data read, executing WRITE="L" makes no change to ACK="H".

When DSP data read, executing REQ="L" makes no change to ACK="L".

When DSP data write, executing WRITE="H" makes no change to ACK="H".

When DSP data write, executing REQ="L" makes no change to ACK="L".

When DSP special code boot, executing DSP reset makes no change to BUSY port "L".

No change to BUSY port "L" before issuing DSP special read command.

( ):

"DIMMER"(S11), "SURROUND BACK"(S14)

STATUS FL Display

2 AC

DSP

1 234

SUB NG SUB " "

DIR NG DIR " "

DSP NG DSP DSP

BUSY "L"

DSP BUSY "L" " "

DSP WRITE="L" ACK="H" " "

DSP REQ="L" ACK="L" " "

DSP WRITE="H" ACK="H" " "

DSP REQ="L" ACK="L" " "

DSP BUSY "L"

DSP BUSY "L" " "

SUB/DSP OK

DSP

" "

Both SUB/DSP OK

No change to BUSY port "L" before DSP version read. " "

(No error display, version display only)

SEMICONDUCTORS

Only major IC's are shown, general IC's etc. are omitted to list.



 IC’s



Note: Abbreviation ahead of IC No. indicates the name of P.W.B., etc.

) : IC No.

PO : Power P.W.B. AD : Audio/Digital P.W.B. CV : Connect/Video P.W.B. DS : DSP P.W.B. CO: Control P.W.B. VI : Video P.W.B. AC : Amp Connect P.W.B. MA: Main Sub Ass'y

M30624MGA (CO: IC506)

100 81

AVR-3803/1083/AVC-3570

TOP VIEW

31 50

M30624MGA Terminal Function

Pin Name FunctionI/O

No.

1 P96/SOUT4 PLRDS DATA O C  Z O/L O/L PLL & RDS control pin (LC72131 & LC72720) 2 P95/CLK4 PLRDS CLK O C  Z O/L O/L PLL & RDS control pin (LC72131 & LC72720) 3 P94/TB4 PLL STB O C  Z O/L O/L PLL control pin (LC72131) 4 P93/TB3 OSD RST O C Z O/L O/L OSD control pin (M35015) 5 P92/SOUT3 OSD DATA O C  Z O/L O/L OSD control pin (M35015) 6 P91/SIN3 OSD STB O C Z O/L O/L OSD control pin (M35015) 7 P90/CLK3 OSD CLK O C  Z O/L O/L OSD control pin (M35015) 8 BYTE BYTE   GND (Ext. data bus bit width switching, 16bit: L)

9 CNVCS CNVSS   

10 P87 ISEL B I  Lv  Eu Z O/L O/L

11 P86 ISEL A I  Lv  Eu Z O/L O/L

12 RESET _RESET I  Lv  Eu L I I Reset input 13 XOUT X1 O   Oscillator connection 14 VSS VSS   GND 15 XIN X2 I  I I Oscillator connection 16 VCC VCC   +5V 17 P85/NMI _NMI I   Not used (Fixed to H) 18 P84/INT2 _B. DOWN I  19 P83/INT1 _PROTECT I  20 P82/INT0 REMOCON I  21 P81 VSEL A I  Lv  Eu Z I O/L Master VR rotation detect input (Rotary encoder)

Symbol

Type

Det

E↓&L E↓&L E↑&L

(Int.)

 Eu Z I I Power down detect (Power down: L)  Ed Z I I Protection detect input (Detected: L)  Z I I Remote control signal input

Re s STBY Stop

(Ext.)

Single-chip/Micro-processor mode switching (Normal single-chip: L, Rewrite boot program start: H input set)

Input selector rotation detect input (Rotary encoder)

AVR-3803/1083/AVC-3570

Pin Name FunctionI/O

No.

22 P80 VSEL B I  Lv  Eu Z I O/L Master VR rotation detect input (Rotary encoder)

23 P77 FUNC STB1 O C  Z O/L O/L

24 P76 FUNC CLK O C  Z O/L O/L CLK output for function switching control 25 P75 FUNC DATA O C - Z O/L O/L DATA output for function switching control

26 P74 FUNC STB2 O C  Z O/L O/L

27 P73/CTS2 FL DATA O C  Z O/L O/L FL tube control pin (LC75721E) 28 P72/CLK2 FL CLK O C  Z O/L O/L FL tube control pin (LC75721E) 29 P71/RXD2 H/P DET I  Z O/L O/L H/P detect input (Detected: H) 30 P70/TXD2 TUNER POWER O N Eu Z O/L O/L TUNER power on/off switching (H: ON) 31 P67/TXD1 TxD O C  Z O/L O/L Data transfer pin to outside 32 P66/RXD1 RxD I  Lv  Z I I Data receive pin from outside 33 P65/CLK1 RESET2 O C Ed Z O/L O/L SUB-µcom reset output 34 P64/CTS1 ACK O C Ed Z O/L O/L MAIN-SUB µcom comm. control pin 35 P63/TXD0 MOSI O C Ed Z O/L O/L MAIN-SUB µcom comm. control pin 36 P62/RXD0 MISO I  Lv  Ed Z I I MAIN-SUB µcom comm. control pin 37 P61/CLK0 Not Used (CLK) O C  Z O/L O/L Not used 38 P60/CTS0 E.VOL STB O C  Z O/L O/L E-VR control output (TC94A32F) 39 P57 E.VOL CLK O C  Z O/L O/L E-VR control output (TC94A32F, TC9459) 40 P56 E.VOL DATA O C  Z O/L O/L E-VR control output (TC94A32F, TC9459) 41 P55/EPM FRASH EPM I  Lv  Z I I Rewrite boot program start: L input set 42 P54 VSDA I/O C  Z I O/L VIDEO IC (Chroma decoder, 3D Y/C) control pin 43 P53 VSCL I/O C  Z I O/L VIDEO IC (Chroma decoder, 3D Y/C) control pin 44 P52 FL RST O C Ed Z O/L O/L FL tube control pin (LC75721E) 45 P51 FL CE O C  Z O/L O/L FL tube control pin (LC75721E) 46 P50/CE FRASH CE I  Z I I Rewrite boot program start: H input set

47 P47 V.EXP CLK O C  Z O/L O/L

48 P46 V.EXP DATA O C  Z O/L O/L

49 P45 V.EXP OE O C Ed Z O/L O/L

50 P44 V.EXP STB O C  Z O/L O/L

51 P43 H/P RELAY O C  Z O/L O/L H/P relay control (H: ON) 52 P42 S BACK RELAY O C  Z O/L O/L Relay control for SURROUND BACK SP 53 P41 SA-RELAY O C  Z O/L O/L Relay control for SURROUND A SP 54 P40 SB-RELAY O C  Z O/L O/L Relay control for SURROUND B SP 55 P37 C-RELAY O C  Z O/L O/L Relay control for CENTER SP 56 P36 F-RELAY O C  Z O/L O/L Relay control for FRONT SP 57 P35 PRE F MUTE O C  Z O/L O/L FRONT PREOUT output muting control, L: Muting

58 P34 PRE C MUTE O C  Z O/L O/L

59 P33 PRE S MUTE O C  Z O/L O/L

60 P32 PRE SB MUTE O C  Z O/L O/L

61 P31

62 VCC VCC   +5V 63 P30 MULTI MUTE O C  Z O/L O/L Pin-jack output muting control of MULTI, L: Muting 64 VSS VSS   GND 65 P27 VOL MUTE O C  Z O/L O/L POWER AMP input muting control, L: Muting

66 P26

67 P25 TUNER MUTE O C  Z O/L O/L TUNER muting control

Symbol

SUB WOOFER MUTE

S.BACK VOL MUTE

Type

OC Z O/L O/L

Det

(Int.)

Re s STBY Stop

(Ext.)

STB output for function switching control (L-ch INPUT&REC/M-ZONE side, EXT IN)

STB output for function switching control (R-ch INPUT&REC/M-ZONE)

CLK output for video switching expander control (BU4094B)

DATA output for video switching expander control (BU4094B)

OE output for video switching expander control (BU4094B)

STB output for video switching expander control (BU4094B)

CENTER PREOUT output muting control, L: Muting

SURROUND PREOUT output muting control, L: Muting

SURROUND BACK PREOUT output muting control, L: Muting

SUB WOOFER PREOUT output muting control, L: Muting

SURROUND BACK POWER AMP input muting control, L: Muting

AVR-3803/1083/AVC-3570

Pin Name FunctionI/O

No.

68 P24 LED CLK O C  Z O/L O/L LED control pin (BU2090F) 69 P23 LED DATA O C Z O/L O/L LED control pin (BU2090F) 70 P22 S MONI. DET I  Lv  Eu Z I O/L S-monitor connection detect input (L: Connected) 71 P21 S SIG. DET I  Lv  Eu Z I O/L S-signal detect input (H: S-signal inputted) 72 P20 SYNC. DET I  Lv  Eu Z I I Sync. detect input (H: Ext. synchronized) 73 P17/INT5 RDS DATAOUT I  74 P16/INT4 REQ I  75 P15/INT3 POWER KEY I 

76 P14/D12 RSPOWER O C Ed Z O/H O/L

77 P13/D11 RECINHA O C  Z O/L O/L

78 P12/D10 SSEL B I  Lv  Eu Z O/L O/L

79 P11/D9 SSEL A I  Lv  Eu Z O/L O/L

80 P10/D8 A+B LIMIT O C  Z O/L O/L

81 P07/D7 VSIGDET I  Z O/L O/L VIDEO signal detect port 82 P06/D6 COMPSIGDET I  Z O/L O/L COMPONENT signal detect port 83 P05/D5 VIDEO POWER O C  Z O/L O/L VIDEO power on/off switching (H: ON)

84 P04/D4 12V TRIGER O C  Z O/L O/L

85 P03/D3 86 P02/D2 RECINHB O C  Z O/L O/L When RECOUT select is VCR1 or VCR2: H 87 P01/D1 POWER O C Ed Z O/L O/L Power relay control output (H: ON) 88 P00/D0 STANDBY O C Eu Z O/L O/L Standby LED drive output (H: Lighted) 89 P107/AN7 KEY1 I  Lv  Eu Z O/L O/L Button input 1 90 P106/AN6 KEY2 I  Lv  Eu Z O/L O/L Button input 2 91 P105/AN5 KEY3 I  Lv  Eu Z O/L O/L Button input 3 92 P104/AN4 STEREO I  Lv  Eu Z I O/L When TUNER FM stereo receive: L 93 P103/AN3 TUNED I  Lv  Eu Z I O/L TUNER tuned detect (L: Tuned) 94 P102/AN2 RDS CE O C  Z O/L O/L RDS data output (LC72720) 95 P101/AN1 RDS RESET O C  Z O/L O/L RDS reset output (LC72720) 96 AVSS AVSS   AD GND 97 P100/AN0 MODE I  Lv  Z O/L O/L Destination switching input 98 VREF VREF   AD ref. +5V 99 AVCC AVCC   AD +5V

100 P97/SIN4 PLL DATAOUT I  Lv  Z I O/L PLL serial data input pin (LC72131)

Symbol

E.VOL STB.MULTI

Type

OC Z O/L O/L E-VR control output (TC9459N)

Det

E↓&L E↓&L E↓&L

(Int.)

 I O/L RDS data input (LC72720)  Ed Z I I MAIN-SUB µcom comm. control pin  I O/L Interrupt port for WAIT mode cancel

Re s STBY Stop

(Ext.)

Same logic as POWER port, when STANDBY mode: H

When RECOUT select is VCR1 or VIDEO other than VCR system: H

Select encoder rotation detect input (Rotary encoder)

SRROUND AMP current limiter control, when SURROUND SP A+B: H

Same logic as POWER port, when MAIN ZONE OFF mode: L

TMP91CW12AF (AD: IC806)

AVR-3803/1083/AVC-3570

100

TMP91CW12AF Terminal Function

Pin No.

1 VREFL VREFL I AD Ref. V GND 2 AVSS AVSS AD GND 3 AVCC AVCC +3V 4 P70/TA0IN DIGITAL POWER O C Ed Z Digital power on/off switching (H: ON) 5 P71/TA1OUT FGAIN O C Ed Z IV AMP gain control output (Sub-woofer on: L) 6 P72/TA3OUT DRECA O C  Z Digital RECOUT switching 7 P73/TA4IN DRECB O C - Z Digital RECOUT switching 8 P74/TA5OUT u SELCK O C  Z ADC/DIR data, clock switching control pin (L: ADC)

9 P75/TA7OUT Not used I Ed Z Not used (GND) 10 P80/TB0IN0/INT5 _INT1 I  11 P81/TB0IN1/INT6 Not used (u ERROR) I Ed Z Not used (GND) 12 P82/TB0OUT0 u ERR MUTE O C  Z Pop noise preventive mute control output (L: Mute)

13 P83/TB0OUT1 u BSE(AC3 MUTE) O C  Z

14 P84/TB1IN0/INT7 Not used I Ed Z Not used (GND) 15 P85/TB1IN1/INT8 Not used I Ed Z Not used (GND) 16 P86/TB1OUT0 Not used I Ed Z Not used (GND) 17 P87/TB1OUT1 Not used I Ed Z Not used (GND) 18 P90/TXD0 MISO O C Ed Z MAIN-SUB µcom comm. control pin (Data output) 19 P91/RXD0 MOSI I Ed Z MAIN-SUB µcom comm. control pin (Data input) 20 P92/SCLK0/CTS0 Not used (CLK) I Ed Z Not used (MAIN-SUB µcom comm. control pin) 21 P93/TXD1 TxD O C Ed Z Data transfer output to outside 22 P94/RXD1 RxD I  Lv  Ed Z Data receive input from outside

23 P95/SCLK1/CTS1 REQ O C Ed Z

Pin Name FunctionI/O

Symbol

Type

Det

(Int.)

E↓&L

 Eu Z DIR control pin (LC89057W-E)

(Ext.)

Res

Digital mute control output, when AC-3 or DTS decode enable: L

MAIN-SUB µcom comm. control pin (Comm. request from SUB-µcom: L)

AVR-3803/1083/AVC-3570

Pin No.

24 AM0 AM0 I Operation mode (Fixed to H) 25 DVCC DVCC +3V 26 X2 XOUT O Oscillator connection 27 DVSS DVSS GND 28 X1 XIN I Oscillator connection 29 AM1 AM1 I Operation mode (Fixed to H) 30 RESET _RESET I  Lv  Eu L Reset input 31 P96/XT1 ADC RESET O N Eu Z A/D control pin (Reset: L) 32 P97/XT2 OSR O N Eu Z A/D control pin (PCM1804), 96kHz: H 33 EMU0 Not used O Ed Z Open 34 EMU1 Not used O Ed Z Open 35 PA0/INT1 Not used I Ed Z Not used (GND) 36 PA1/INT2 Not used I Ed Z Not used (GND) 37 PA2/INT3 Not used I Ed Z Not used (GND) 38 PA3/INT4 Not used I Ed Z Not used (GND) 39 PA4 Not used I Ed Z Not used (GND) 40 PA5 Not used I Ed Z Not used (GND) 41 PA6 Not used I Ed Z Not used (GND) 42 PA7 Not used I Ed Z Not used (GND) 43 ALE ALE O C  Z Open 44 P00/AD0 I/O1 I/O C Z DSP comm. pin (ADSST-MEL100:D16) 45 P01/AD1 I/O2 I/O C Z DSP comm. pin (ADSST-MEL100:D17) 46 P02/AD2 I/O3 I/O C Z DSP comm. pin (ADSST-MEL100:D18) 47 P03/AD3 I/O4 I/O C Z DSP comm. pin (ADSST-MEL100:D19) 48 P04/AD4 I/O5 I/O C Z DSP comm. pin (ADSST-MEL100:D20) 49 P05/AD05 I/O6 I/O C  Z DSP comm. pin (ADSST-MEL100:D21) 50 P06/AD06 I/O7 I/O C  Z DSP comm. pin (ADSST-MEL100:D22) 51 P07/AD07 I/O8 I/O C  Z DSP comm. pin (ADSST-MEL100:D23) 52 P10/AD8/A8 ROM_RST1 O C Ed Z Memory reset for DSP (Reset: L) 53 P11/AD9/A9 DSP1_RS O C Ed Z DSP reset output pin (Reset: L) 54 P12/AD10/A10 DSP I/0 POWER O C Eu Z Power on: L (10ms later on after digital power on) 55 P13/AD11/A11 DSP OSC ON O C  Z ON: H (20ms later on after digital power on)

56 P14/AD12/A12 IRQ1_B1(DSP_REQ1) O C  Z

57 P15/AD13/A13 DINA O C  Z Digital input switching 58 P16/AD14/A14 DINB O C  Z Digital input switching 59 P17/AD15/A15 DINC O C  Z Digital input switching 60 P20/A0/A16 DACCS O C Z DAC control pin (PCM1791: Chip select) 61 P21/A1/A17 DACMDI O C Z DAC control pin (PCM1791) 62 DVSS DVSS GND 63 NMI NMI I Fixed to H 64 DVCC DVCC +3V

65 P22/A2/A18 DAC-RESET1 O C  Z

66 P23/A3/A19 DACMC O C  Z DAC control pin (PCM1791) 67 P24/A4/A20 Not used I  Z Not used (GND) 68 P25/A5/A21 DRECC O C  Z Digital RECOUT switching 69 P26/A6/A22 Not used I Z Not used (GND) 70 P27/A7/A23 Not used I  Z Not used (GND)

71 P30/RD/BOOT _BOOT I Eu Z

72 P31/WR FLAG 0A(WRITE1) O C Eu Z DSP comm. control pin (DATA WRITE: H)

73 P32/HWR DSP_BOOT I Eu H(Iu)

74 P33/WAIT Not used I Ed H(Iu) Not used (GND) 75 P34/BUSRQ Not used I Ed H(Iu) Not used (GND) 76 P35/BUSAK Not used I Ed H(Iu) Not used (GND)

Pin Name FunctionI/O

Symbol

Type

Det

(Int.)

(Ext.)

Res

DSP (ADSST-MEL100:IRQ 1_) host I/F interrupt request output, REQ: L

DAC control pin (L: Power down mode, ↑: Reset, H: Normal)

With “L” input set during reset, rewrite boot program start

DSP or SUB rewrite boot program (When DSP rewrite “L” input)

+ 60 hidden pages