Dell Latitude D630 XFR User Manual

Dell™ Latitude™ XFR D630
Fully Rugged Notebook
User’s Guide
Finding Information About Your Computer Reinstalling Software Transferring Information to Another Computer Adding and Replacing Parts Using a Battery Using the Keyboards Traveling With Your Computer Using the DirectVue Displays Customer Support Setting Up and Using Networks Specifications Using Multimedia Safety Information Using Cards Regulatory Information Securing Your Computer Glossary Troubleshooting
System Setup Program
DellTM QuickSet
Notes, Notices, and Cautions
NOTE: A NOTE indicates important information that helps you make better use of your computer.
NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the
problem.
CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death. WARNING: A WARNING indicates a potentially hazardous situation which, if not avoided, could result
in death or serious injury.
Information in this document is subject to change without notice. © 2007-2008 Dell Inc. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Dell Incorporated is strictly forbidden This document is provided for informational purposes only, and may contain typographical errors and technical inaccuracies. The content is
provided as is, without express or implied warranties of any kind.
Dell, the DELL logo, Latitude, Wi - Fi Catcher and ExpressCharge are registered trademarks of Dell Inc.; QuadCool, Armored Protection System (APS), and DirectVue are trademarks of Augmentix Corporation; Intel, Pentium and Core are registered trademarks of Intel Corporation; Microsoft, Windows, Windows Vista and Outlook are registered trademarks of Microsoft Corporation; Bluetooth is a registered trademark of
Bluetooth SIG, Inc.; TouchStrip is a trademark of UPEK, Inc.; Touchkit is a trademark of eGalax_eMPIA Technology Inc. (EETI). Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their
products. Dell Incorporated disclaims any proprietary interest in trademarks and trade names other than its own.
1 Finding Information
NOTE: Some features or media may be optional and may not ship with your computer. Some features or media
may not be available in certain countries.
NOTE: Additional information may ship with your computer.
CAUTION: The XFR D630 Fully Rugged Notebook User’s Guide provides important safety and regulatory
information. See the 117HSafety Information and 118HRegulatory Information sections for further details.
Documentation Purpose Document Location
‘Open Me First’ Envelope XFR D630 Fully Rugged
Notebook Quick Reference Guide
XFR D630 Fully Rugged Notebook User’s Guide
Documentation and Driver CD
Dell Drivers and Utilities CD (Optional)
Operating System CD (Optional)
Windows Help and Support Center
Service Tag
Microsoft Windows License Label
Provides a single location where the documentation and CDs shipped with the XFR D630 can be located
Guides you through your initial XFR D630 Notebook setup
How to configure your system settings
·
How to remove/replace parts
·
How to troubleshoot and solve problems
·
Specifications
·
Safety and regulatory information
·
Customer Care Program information
·
The Documentation and Driver CD contains:
Product documentation
·
Supplemental Dell documentation
·
NOTE: The Drivers and Utilities CD may be optional and may not ship with your computer. Documentation and drivers are already installed on your computer. You can use the media to reinstall drivers and to run Dell Diagnostics (see "
119HDell Diagnostics").
Readme files may be included on your media to provide last-minute updates about technical changes to your computer or advanced technical reference material for technicians or experienced users.
How to reinstall your operating system
How to use Windows operating system
·
How to work with programs and files
·
How to personalize your desktop
·
The Service Tag is located on the bottom of your computer. Use the Service Tag to identify your computer when you contact Customer Support.
This label provides your Microsoft Windows License information.
·
In the shipping container
Available on the Documentation
·
and Driver CD
·
Available in the ‘Open Me First’
envelope
Available on the Documentation
·
and Driver CD
Available in the ‘Open Me First’
·
envelope
Optionally available in the ‘Open
·
Me First’ envelope
NOTE: The Operating System CD is optional and may not ship with your computer. The operating system is already installed on your computer. To reinstall your operating system, use the Operating System CD. See
120HRestoring Your Operating System ".
" After you reinstall your operating system, use the optional Drivers and Utilities CD to reinstall drivers for the devices that came with your computer. Your operating system product key label is located in the ‘Open Me First’ envelope.
1.
Click Start or à Help and
Support
Type a word or phrase that
2. describes your problem and click the arrow icon
Click the topic that describes you
3. problem
Follow the instructions on the
4. screen
This label is located on your computer.
This label is located on your computer.
Dell Support Utility
Software upgrades and troubleshooting hints, frequently asked questions, hot topics, and general health of your computer
The Dell Support Utility automated upgrade and notification system installed on your computer. This support provides real -time health scans of your computing environment, software updates, and relevant self-support information. Access the Dell Support Utility from
icon in the taskbar. For more
the
information, see "
121H
Dell Support
122HDell QuickSet”.
Dell Quickset Help
Information on network activity, the Power Management Wizard, hotkeys, and other items controlled by Dell QuickSet
Utility". To view Dell QuickSet Help, right­clock the QuickSet icon in the Microsoft Windows taskbar. For more information on Dell QuickSet, see “
2 About Your Computer
2.1 Overview
The XFR D630 Fully Rugged Notebook provides Xtreme Terrain GradeTM protection through rugged design expertise and independent MIL-STD testing and validation.
The Armored Protection System over-mold protection, and the patent-pending QuadCoolTM thermal management system.
The QuadCool thermal management system is a multi-faceted thermal management system that combines enhanced forced convection and conductive cooling focused on the internal core system components, primary memory, storage and smart battery elements. QuadCool technology moves heat away from core system components and elements to the exterior of the system.
The XFR D630 provides the rugged industry’s first 14.1” wide-aspect LCD providing brighter, sharper and superior viewability. The DirectVue reduced reflectivity and a proprietary optical enhancement. Optionally available is the DirectVueTM Touch Display.
With the XFR D630, you have the option to choose between two keyboards. The standard keyboard provides a sealed, full-sized keyboard while the optional backlit keyboard provides a sealed, full-sized, backlit, rubber keyboard.
Your XFR D630 Fully Rugged Notebook has a common IT platform and architecture with Dell ATGTM D630 notebooks, thereby simplifying IT management and reducing support and administrative time and costs. This
also means operating system images, drivers, firmware and other key IT architecture elements remain consistent across the Dell offerings; and therefore there is a family of supporting tools that are available to assist you with your notebook.
The result is a notebook that is not only rugged - it is Rugged Redefined™.
TM
(APS) is a proven ruggedization system that includes a dense magnesium exoskeleton,
TM
Display technology offers optimal sunlight-readability because of its increased brightness,
TM
’s LatitudeTM D630 and
2.2 Front View
Figure 2 1 XFR D630 Front View
1 Display latch 2
4 Device status lights 5
TM
DirectVue DirectVue Standard keyboard or Backlit
rubber keyboard
Display or
TM
Touch Display
3 Power button
6
Biometric (fingerprint) reader - optional
7
10 Handle 11 13
16 Ambient light sensor (ALS) 17 Mute button 18 Keyboard illumination lights
Stylus and stylus tether (with Touch Display option)
Track stick (standard keyboard only)
CAUTION: The optional DirectVueTM Touch Display has been designed to accept finger touch as well as passive stylus input directly onto the screen. With the optional DirectVueTM Touch Display, a stylus is
included with the XFR D630 for use in selecting items on the touch screen. Other pointing devices can be used with the touch screen such as any non- abrasive, smooth or blunt object that will not damage the touch screen display. The touch screen surface can be damaged by ink pens, marker pens or other pointed or abrasive objects. The use of non -approved input devices that cause damage to the digitizer or LCD may not be covered by the limited warranty.
8
14 Keyboard status lights 15 Volume control buttons
Stylus housing (with Touch Display option)
Touch pad/Track stick buttons
9 Speaker
12 Touch pad
2.2.1 Device Status Lights
If the computer is connected to an electrical outlet, the light operates as follows:
– Solid green: The battery is charging. – Flashing green: The battery is almost fully charged. – Off: The battery is adequately charged (or external power is not available to charge the battery).
If the computer is running on a battery, the
– Off: The battery is adequately charged (or the computer is turned off). – Flashing orange: The battery charge is low. – Solid orange: The battery charge is critically low.
light operates as follows:
2.2.2 Volume Control Buttons
Press these buttons to adjust the volume.
2.2.3 Mute Button
Press this button to turn off the volume.
2.2.4 Displays
For more information about the standard DirectVueTM Display and the optional DirectVue Touch Display, see "123HUsing the DirectVue Displays". The Display Latch keeps the display closed. The Display Latch Button is pressed to release the display latch and open the display.
2.2.5 Keyboard
You have the option of choosing the standard sealed, full-sized keyboard or the backlit, rubber, sealed full-sized keyboard. Both keyboards include a numeric keypad as well as the Microsoft® Windows® logo key. For information on
supported keyboard shortcuts, see "
124HUsing the Keyboard".
2.2.6
Keyboard Status Lights
2.2.7 Keyboard Illumination Lights
Press <Fn> and the right-arrow key to toggle on and off these lights for illumination of the keyboard in low-light environments. These keyboard combinations are valid on both the standard and the rubber, backlit keyboard.
Keyboard Illumination <Fn> and right-arrow key Toggles the keyboard illumination lights on and off.
Display Functions <Fn> and left-arrow key Activates the ambient light sensor, which controls brightness of the
display based on light level in the current environment.
<Fn> and up-arrow key Increases brightness on the integrated display only (not on an external
monitor).
<Fn> and down-arrow key Decreases brightness on the integrated display only (not on an external monitor).
2.2.8 Touch Pad
Provides the functionality of a mouse (see "125HTouch Pad and Track Stick").
2.2.9 Track Stick
Provides the functionality of a mouse (see "126HTouch Pad and Track Stick").
NOTE: The track stick is only supported on the standard keyboard.
2.2.10 Touch Pad Buttons/Track Stick Buttons
Use these buttons much like the buttons on a mouse when you use the touch pad and track stick to move the cursor on the display (see "
127HTouch Pad and Track Stick").
2.2.11 Power Button
Press the power button to turn on the computer or to enter or exit a power management mode.
NOTICE: To avoid losing data, shut down your computer instead of pressing the power button.
2.2.12 Biometric (Fingerprint) Reader (optional)
The optional biometric (fingerprint) reader helps to keep your Dell computer secure.
Figure 2 2 Biometric (Fingerprint) Reader
1 Biometric (Fingerprint) Reader
To access the biometric reader, you must first slide down the protective door that covers the reader. When you place your finger on the exposed reader, it uses your unique fingerprint to authenticate your user identity. For information on how to activate and use the security management software that controls the fingerprint reader, see "
128HSecurity Management
Software”.
2.2.13 Speaker
To adjust the volume of the integrated speaker, press the volume control buttons, mute button, or volume-control keyboard shortcuts (see "
129HKey Combinations").
2.2.14 Ambient Light Sensor
Detects available environmental light and automatically increases or decreases the display backlighting to compensate for low-light and high-light environments. Press the <Fn> and left-arrow keys to enable or disable the sensor ("
130HUsing the
Ambient Light Sensor").
2.3 Left Side View
Figure 2 3 XFR D630 Left Side with Connectors/Devices Protected
The connectors and devices on the computer are protected from ingress by dense magnesium hinged and friction fit
problem with the fan or the computer.
doors. This protection is a component of the Armored Protection System.
Figure 2 4 XFR D630 Left Side with Connectors/Devices Revealed
1
4
7
The following is applicable to UL 1604 and CSA C22.2 No. 213 compliant systems:
Air vents (protected from ingress)
Smart card reader (standard or enclosed)
PC card/ExpressCard slot
WARNING - Explosion Hazard - Do not disconnect equipment unless power has been removed or the area is known to be non-hazardous
WARNING - Explosion Hazard - Do not utilize any of the connectors/hubs unless area is known to be non-hazardous
2 Security cable slot 3 Audio connectors (2)
5 1394 connector 6 Wireless switch
2.3.1 Air Vents
The computer uses an internal fan to create airflow through the vents, which prevents the computer from overheating.
The Air Vents are part of the QuadCool thermal management system. They provide external venting of internal heat via the enhanced convection cooling system.
CAUTION: Do not block, push objects into, or allow dust to accumulate in the air vents. Do not store your computer in a low-airflow environment, such as a closed briefcase, while it is running. Restricting the airflow can damage the computer or cause a fire.
NOTE: This computer turns on the fan when the computer gets hot. Fan noise is normal and does not indicate a
2.3.2 Security Cable Slot
Lets you attach a commercially available antitheft device to the computer (see "131HSecurity Cable Lock").
2.3.3 Audio Connectors
2.3.4 IEEE 1394 Connector
Connects devices supporting IEEE 1394 high-speed transfer rates, such as some digital video cameras.
2.3.5 Smart Card Reader (with blank)
Supports one smart card. Smart cards provide a variety of functions, including security features and data storage. The blank prevents foreign matter from entering the interior of the computer when a smart card is not installed in the smart card slot. For more information and instructions on removing the blank, see "
132HSmart Cards".
2.3.6 Wireless Switch
When enabled through Dell QuickSet, this switch can scan for a wireless LAN (WLAN) in your vicinity. You can also use it to rapidly turn off or on any wireless devices such as WLAN cards and internal cards with Bluetooth wireless technology
133HDell Wi-Fi Catcher™ Network Locator").
(see "
“momentary” position –
“off” position –
1
disables wireless devices
“on” position – enables
2
wireless devices
Scans for WLAN networks
134HDell Wi-Fi
(see “
3
CatcherTM Network Locator”)
2.3.7 PC Card Slot
Supports one PC Card, such as a modem or network adapter. The computer ships with a blank installed in the slot to prevent foreign matter from entering the computer interior when a card is not installed (see "
135HCard Types").
2.4 Right Side View
Figure 2 5 XFR D630 Right Side with Connectors/Devices Protected
The connectors and devices on the computer are protected from ingress by dense magnesium hinged and friction fit doors. This protection is a component of the Armored Protection System.
Figure 2 6 XFR D630 Right Side with Connectors/Devices Revealed
1 XBay expansion bay 2 XBay device latch release 3 USB connectors (2)
The following is applicable to UL 1604 and CSA C22.2 No. 213 compliant systems:
WARNING - Explosion Hazard - Do not disconnect equipment unless power has been removed or the area is known to be non-hazardous
WARNING - Explosion Hazard - Do not utilize any of the connectors/hubs unless area is known to be
non-hazardous
2.4.1 XBay
XBay expansion bay supports a floppy or an optical drive, second battery or second hard drive (see "136HUsing Multimedia").
2.4.2 XBay Device Latch Release
Press the latch release to eject any device installed in the XBay.
2.4.3 USB Connectors
Connect USB devices such as a mouse, keyboard, or printer.
2.5 Back View
Figure 2 7 XFR D630 Back View with Connectors Protected
The connectors and devices on the computer are protected from ingress by dense magnesium hinged and friction fit doors. This protection is a component of the Armored Protection System.
Figure 2 8 XFR D630 Back View with Connectors Revealed
1
4 Serial connector 5 Video connector 6 AC adapter connector
7
The following is applicable to UL 1604 and CSA C22.2 No. 213 compliant systems:
Network connector (RJ-45)
Air vents (protected from ingress)
CAUTION: Do not block, push objects into, or allow dust to accumulate in the air vents. Do not store your computer in a low-airflow environment, such as a closed briefcase, while it is running. Restricting the airflow can damage the computer or cause a fire.
WARNING - Explosion Hazard - Do not disconnect equipment unless power has been removed or the area is known to be non-hazardous
2
Modem connector (RJ-11)
3 USB connectors (2)
WARNING - Explosion Hazard - Do not utilize any of the connectors/hubs unless area is known to be non-hazardous
2.5.1 Network Connector (RJ-45)
NOTICE: The network connector is slightly larger than the modem connector. To avoid damaging the computer, do
not plug a telephone line into the network connector.
Connects the computer to a network. The two lights next to the connector indicate status and activity for wired network connections. For information on using the network adapter, see the device user’s guide supplied with your computer.
2.5.2 Modem Connector (RJ-11)
Connect the telephone line to the modem connector. For information on using the modem, see the documentation supplied with your modem.
2.5.3 USB Connectors
Connects USB devices, such as a mouse, keyboard, or printer.
2.5.4 Serial Connector
Connects serial devices such as a mouse, keyboard, or printer.
2.5.5 Video Connector
Connects video devices, such as a monitor.
2.5.6 AC Adaper Connector
Connects an AC adapter to the computer.
Figure 2 9 Connecting the AC Adapter
1 AC adapter 2 AC adapter connector
The AC adapter converts AC power to the DC power required by the computer. You can connect the AC adapter with your computer turned either on or off.
CAUTION: The AC adapter works with electrical outlets worldwide. However, power connectors and power strips vary among countries. Using an incompatible cable or improperly connecting the cable to the power strip or electrical outlet may cause fire or equipment damage.
NOTICE: When you disconnect the AC adapter cable from the computer, grasp the connector, not the cable itself,
and pull firmly but gently to avoid damaging the cable. When you wrap the AC adapter cable, ensure that you follow the angle of the connector on the AC adapter to avoid damaging the cable.
2.5.7 Air Vents
The computer uses an internal fan to create airflow through the vents, which prevents the computer from overheating.
The Air Vents are part of the QuadCool thermal management system. They provide external venting of internal heat via the enhanced convection cooling system.
CAUTION: Do not block, push objects into, or allow dust to accumulate in the air vents. Do not store your computer in a low-airflow environment, such as a closed briefcase, while it is running. Restricting the airflow can damage the computer or cause a fire.
2.6 Bottom View
Figure 2 10 XFR D630 Bottom View with Connectors/Devices Protected
1
4 Battery compartment cover 5 XBay device locking screw
The compartments on the bottom of the computer are protected from ingress by dense magnesium compartment doors. This protection is a component of the Armored Protection System.
The following is applicable to UL 1604 and CSA C22.2 No. 213 compliant systems:
Docking device connector cover
WARNING - Explosion Hazard - Do not disconnect equipment unless power has been removed or the area is known to be non-hazardous
WARNING - Explosion Hazard - Do not utilize any of the connectors/hubs unless area is known to be non-hazardous
2 Memory module cover 3
Hard disk drive compartment cover
2.6.1 Docking-Device Connector
Lets you attach your computer to a docking device. See the documentation that came with your docking device for more information.
2.6.2 Memory Module Cover
The memory module cover provides a cover for the compartment that contains the second memory module connector (DIMM B) (see "
137HMemory").
2.6.3 Hard Disk Drive Compartment Cover
The hard disk drive compartment covers the compartment that contains the hard disk drive. See “138HHard Drive” for additional information.
2.6.4 Battery Compartment Cover
The battery compartment cover provides a cover for the compartment that contains the battery. For additional information regarding the use and access of the battery, see “
139HUsing a Battery”.
2.6.5 XBay Device Locking Screw
Locks the device in the XBay in place such as an optical drive (see “140HXBay”).
3 Transferring Information to Another Computer
You can use your operating system wizards to help you transfer files and other data from one computer to another. For
and files and click Next. The wizard reads the collected files and settings and applies them to your destination
instructions, see the following section that corresponds to the operating system that your computer is running.
NOTE: "Old computer" or "source computer" refers to the original computer from which the information is transferred; "new computer" or "destination computer" refers to the computer to which you transfer the information.
3.1 Microsoft® Windows® XP
The Microsoft Windows XP operating system provides the Files and Settings Transfer wizard to move data from a source computer to a new—destination—computer. You can transfer data such as:
E-mail messages
·
·
Toolbar settings
·
Window sizes
·
Internet bookmarks
You can transfer the data to the destination computer over a network, serial connection, or on removable media such as a writable CD.
NOTE: You can transfer information from the source computer to the destination computer by directly connecting a serial cable to the input/output (I/O) ports of the two computers. To transfer data over a serial connection, you must access the Network Connections utility from the Control Panel and perform additional configuration steps, such as setting up an advanced connection and designating the host computer and the guest computer.
For instructions on setting up a direct cable connection between two computers, see Microsoft Knowledge Base 87uArticle #305621, titled How to Set Up a Direct Cable Connection Between Two Computers in Windows XP. This information may not be available in some countries.
For transferring information to a new computer, you must run the Files and Settings Transfer Wizard. You can use the optional Operating System media for this process or you can create a wizard disk with the Files and Settings Transfer Wizard.
3.1.1 Running the Files and Settings Transfer Wizard With the Operating System Media
NOTE: This procedure requires the Operating System media. This media is optional and may not be included with
all computers.
To prepare the new computer for the file transfer:
Click Start All Programs Accessories System Tools Files and Settings Transfer Wizard.
1.
2. When the Files and Settings Transfer Wizard welcome screen appears, click Next.
On the Which computer is this? screen, click New Computer and click Next.
3.
On the Do you have a Windows XP CD? screen, click I will use the wizard from the Windows XP CD and
4. click Next.
When the Now go to your old computer screen appears, go to your old or source computer. Do not click Next
5. at this time.
To copy data from the source computer:
On the source computer, insert the Windows XP Operating System media.
1.
On the Welcome to Microsoft Windows XP screen, click Perform additional tasks.
2.
Under What do you want to do?, click Transfer files and settings.
3.
On the Files and Settings Transfer Wizard welcome screen, click Next.
4.
On the Which computer is this? screen, click Old Computer and click Next.
5.
On the Select a transfer method screen, click the transfer method you prefer.
6.
On the What do you want to transfer? screen, select the items you want to transfer and click Next. After the
7. information has been copied, the Completing the Collection Phase screen appears.
Click Finish.
8.
To transfer data to the destination computer:
On the Now go to your old computer screen on the destination computer, click Next.
1.
On the Where are the files and settings? screen, select the method you chose for transferring your settings
2.
computer. When all of the settings and files have been applied, the Finished screen appears.
3. Click Finished and restart the destination computer.
3.1.2 Running the Files and Settings Transfer Wizard Without the Operating System Media
To run the Files and Settings Transfer Wizard without the Operating System media, you must create a wizard disk that will allow you to create a backup image file to removable media.
To create a wizard disk, use your destination computer with Windows XP and perform the following steps:
Click Start All Programs Accessories System Tools Files and Settings Transfer Wizard.
1.
2. When the Files and Settings Transfer Wizard welcome screen appears, click Next.
3. On the Which computer is this? screen, click New Computer Next.
4. On the Do you have a Windows XP CD? screen, click I want to create a Wizard Disk in the following drive Next.
5. Insert the removable media, such as a writable CD, and click OK.
When the disk creation completes and the Now go to your old computer message appears, do not click Next.
6.
Go to the source computer.
7.
To copy data from the source computer:
On the source computer, insert the wizard disk.
1.
2. Click Start Run.
3. In the Open field on the Run window, browse to the path for fastwiz (on the appropriate removable media) and click OK.
On the Files and Settings Transfer Wizard welcome screen, click Next.
4.
5. On the Which computer is this? screen, click Old Computer Next.
6. On the Select a transfer method screen, click the transfer method you prefer.
On the What do you want to transfer? screen, select the items you want to transfer and click Next. After the
7. information has been copied, the Completing the Collection Phase screen appears.
Click Finish.
8.
To transfer data to the destination computer:
On the Now go to your old computer screen on the destination computer, click Next.
1.
On the Where are the files and settings? screen, select the method you chose for transferring your settings
2. and files and click Next. Follow the instructions on the screen. The wizard reads the collected files and settings and applies them to your destination computer. When all of the settings and files have been applied, the Finished screen appears.
Click Finished and restart the destination computer.
3.
3.2 Microsoft Windows Vista
TM
1. Click the Windows Vista Start button, , and then click Transfer files and settings→ Start Window Easy Transfer.
In the User Account Control dialog box, click Continue.
2.
Click Start a new transfer or Continue a transfer in progress.
3.
Follow the instructions provided on the screen by the Windows Easy Transfer wizard.
3.2.1 Easy Transfer Cable for Windows Vista
NOTE: Dell does not provide the Easy Transfer Cable.
Insert the Easy Transfer Cable for Windows Vista Application Software media into the computer from which you
1. are transferring data.
Follow the on-screen instructions until you are prompted to connect the Transfer Cable.
2.
Connect the Easy Transfer Cable to the source computer.
3. You are prompted to select a device option.
Continue until you are prompted to plug the other end of the Easy Transfer Cable into the destination computer.
4. The screen indicates that a connection has been made.
At the computer from which you are transferring data, follow the on-screen instructions to select the settings and
5. files you want to transfer.
You will come to a screen that indicates that you are ready to transfer files.
6.
From the destination computer, view the transfer and wait for the indication that the transfer is complete.
7.
Select Close.
8. You are prompted to restart the computer.
9.
Select Yes.
The computer reboots and the transfer is complete.
4 Using a Battery
4.1 Battery Performance
NOTE: For information about the warranty for your computer, see the Limited Warranty document.
For optimal computer performance and to help preserve BIOS settings, operate your Dell portable computer with the main battery installed at all times. One battery is supplied as standard equipment in the battery compartment.
NOTE: Because the battery may not be fully charged, use the AC adapter to connect your new computer to an electrical outlet the first time you use the computer. For best results, operate the computer with the AC adapter until the battery is fully charged. To view the battery charge status, check the Power Meter in Power Options (see
141HAccessing Power Options Properties”).
Battery operating time varies depending on operating conditions. You can install an optional second battery in the XBay to significantly increase operating time.
NOTE: Battery operating time (the time the battery can hold a charge) decreases over time. Depending on how often the battery is used and the conditions under which it is used, you may need to purchase a new battery during the life of your computer.
NOTE: It is recommended that you connect your computer to an electrical outlet when writing to a CD or DVD
Operating time is significantly reduced when you perform operations including, but not limited to, the following:
Using optical drives
·
· Using wireless communications devices, PC Cards, media memory cards, or USB devices
· Using high-brightness display settings, 3D screen savers, or other power-intensive programs such as complex 3D
graphics applications
Running the computer in maximum performance mode. See "142HConfiguring Power Management
·
Settings" for information about accessing Windows Power Options Properties or Dell Quickset, which you can use to configure power management settings.
You can check the battery charge (see "143HChecking the Battery Charge") before you insert the battery into the computer. You can also set power management options to alert you when the battery charge is low.
CAUTION: Using an incompatible battery may increase the risk of fire or explosion. Replace the battery only with a compatible battery purchased from Dell. The battery is designed to work with your computer. Do not use a battery from other computers with your computer.
CAUTION: Do not dispose of batteries with household waste. When your battery no longer holds a charge, call your local waste disposal or environmental agency for advice on disposing of a lithium-ion battery. See "
CAUTION: Misuse of the battery may increase the risk of fire or chemical burn. Do not puncture, incinerate, disassemble, or expose the battery to temperatures above
away from children. Handle damaged or leaking batteries with extreme care. Damaged batteries may leak and cause personal injury or equipment damage. Maximum system storage temperature is
0
(160
F) without the battery installed.
144HBattery Disposal".
650C (1490F). Keep the battery
710C
4.2 Checking the Battery Charge
The Dell QuickSet Battery Meter, the Microsoft Windows Power Meter window and icon, the battery charge gauge and health gauge, and the low-battery warning provide information on the battery charge.
4.2.1 Dell™ QuickSet Battery Meter
If Dell QuickSet is installed, press <Fn><F3> to display the QuickSet Battery Meter. The Battery Meter displays status,
battery health, charge level, and charge completion time for the battery in your computer. For more information about QuickSet, right-click the Quickset icon in the taskbar, and click Help.
4.2.2 Microsoft® Windows® Power Meter
The Windows Power Meter indicates the remaining battery charge. To check the Power Meter, double-click the icon on the taskbar. If the computer is connected to an electrical outlet, a icon appears.
4.2.3 Charge Gauge
To access the charge gauge you must first remove the battery compartment cover. See “145HReplacing the Battery” for instructions regarding removing the battery compartment cover. By either pressing once or pressing and holding the status button on the charge gauge on the battery, you can check:
Battery charge (check by pressing and releasing the status button)
·
· Battery health (check by pressing and holding the status button)
1 Battery 2 Status buttons 3 Charge gauge
The battery operating time is largely determined by the number of times it is charged. After hundreds of charge and discharge cycles, batteries lose some charge capacity — or battery health. That is, a battery can show a status of "charged" but maintain a reduced charge capacity (health).
4.2.3.1 Check the Battery Charge
To check the battery charge, press and release the status button on the battery charge gauge to illuminate the charge­level lights. Each light represents approximately 20 percent of the total battery charge. For example, if the battery has 80 percent of its charge remaining, four of the lights are on. If no lights appear, the battery has no charge.
4.2.3.2 Check the Battery Health
NOTE: You can check battery health in one of two ways: by using the charge gauge on the battery as described
below or by using the Battery Meter in Dell QuickSet. For information about QuickSet, right -click the icon in the taskbar, and click Help.
To check the battery health using the charge gauge, press and hold the status button on the battery charge gauge for at least 3 seconds. If no lights appear, the battery is in good condition, and more than 80 percent of its original charge capacity remains. Each light represents incremental degradation. If five lights appear, less than 60 percent of the charge capacity remains, and you should consider replacing the battery. See “ operating time.
146HCharge Gauge” for information about the battery
4.3 Low-Battery Warning
NOTICE: To avoid losing or corrupting data, save your work immediately after a low-battery warning. Then
connect the computer to an electrical outlet, or install a second battery in the XBay. If the battery runs completely out of power, hibernate mode begins automatically.
A pop-up window warns you when the battery charge is approximately 90 percent depleted. If two batteries are installed,
the low-battery warning means that the combined charge of both batteries is approximately 90 percent depleted. The
computer enters hibernate mode when the battery is at a critically low level. You can change the settings for the battery alarms in QuickSet or the Power Options Properties window. See
"147HConfiguring Power Management Settings" for information about accessing QuickSet or the Power Options Properties window.
4.4 Conserving Battery Power
Perform the following actions to conserve battery power:
Connect the computer to an electrical outlet when possible because battery life is largely determined by the
·
number of times the battery is used and recharged.
· Place the computer in standby mode or hibernate mode when you leave the computer unattended for long periods of time. See "148HPower Management Modes".
· Use the Power Management Wizard or the Power Options Properties window to select options to optimize your computer’s power usage. These options can also be set to change when you press the power button, close the display, or press <Fn><Esc>.
NOTE: See "149HConfiguring Power Management Settings" for information on conserving battery power.
4.5 Power Management Modes
4.5.1 Standby and Sleep Mode
Standby mode (sleep mode in Microsoft Windows Vista™) conserves power by turning off the display and the hard drive after a predetermined period of inactivity (a time-out). When the computer exits standby or sleep mode, it returns to the same operating state it was in before entering standby or sleep mode.
NOTICE: If your computer loses AC and battery power while in standby or sleep mode, it may lose data.
To enter standby mode in Windows XP, click the Start button, click Turn off computer, and then click Stand by.
To enter sleep mode in Windows Vista, click the Windows Vista Start button, Depending on how you set the power management options in the Power Options Properties window or the QuickSet
Power Management Wizard, you may also use one of the following methods:
Press the power button.
·
·
Close the display.
·
Press <Fn><Esc>.
To exit standby or sleep mode, press the power button or open the display, depending on how you set the power management options. You cannot make the computer exit standby or sleep mode by pressing a key or touching the touch pad or track stick.
, and then click Sleep.
4.5.2 Hibernate Mode
Hibernate mode conserves power by copying system data to a reserved area on the hard drive and then completely turning off the computer. When the computer exits hibernate mode, it returns to the same operating state it was in before entering hibernate mode.
NOTICE: You cannot remove devices or undock your computer while your computer is in hibernate mode.
Your computer enters hibernate mode if the battery charge level becomes critically low. To manually enter hibernate mode in Windows XP, click Start Turn off computer, press and hold
<Shift>, and click Hibernate. For information about the hibernate mode in Windows Vista, search for the keyword hibernate in
Windows Help and Support (click Start Help and Support). Depending on how you set the power management options in the Power Options Properties window or the QuickSet
Power Management Wizard, you may also use one of the following methods to enter hibernate mode:
· Press the power button.
·
Close the display.
·
Press <Fn><F1>.
NOTE: Some PC Cards may not operate correctly after the computer exits hibernate mode. Remove and reinsert
the card (see “
To exit hibernate mode, press the power button. The computer may take a short time to exit hibernate mode. You cannot make the computer exit hibernate mode by pressing a key or touching the touch pad or track stick. For more information on hibernate mode, see the documentation that came with your operating system.
150HRemoving a Card or Blank”), or simply restart (reboot) your computer.
4.6 Configuring Power Management Settings
You can use the QuickSet Power Management Wizard or Windows Power Options Properties to configure the power management settings on your computer. For more information about QuickSet, right-click the QuickSet icon in the taskbar and click Help.
4.6.1 Accessing Power Options Properties
Windows XP Click Start Control Panel Performance and Maintenance Power Options.
Windows Vista Click Start Control Panel System and Maintenance Power Options.
4.7 Charging the Battery
NOTICE: The battery temperature must be between 00C and 550C (320F and 1310F) to charge. If the battery is
not in this temperature range when a charge is attempted, the may happen when the battery has gotten hot from being used in your computer or in a hot environment. Disconnect the computer from the electrical outlet and allow the computer and the battery to cool to the charging temperature range. Then connect the computer to an electrical outlet to continue charging the battery.
NOTE: With Dell™ ExpressCharge™, when the computer is turned off, the AC adapter charges a completely discharged battery to 80 percent in approximately 1 hour and to 100 percent in approximately 2 hours. Charge time is longer with the computer turned on. You can leave the battery in the computer as long as you like. The battery’s internal circuitry prevents the battery from overcharging. Battery charge times may vary dependent upon the ambient temperature.
When you connect the computer to an electrical outlet or install a battery while the computer is connected to an electrical outlet, the computer checks the battery charge and temperature. If necessary, the AC adapter then charges the battery and maintains the battery charge.
For more information about resolving problems with a battery, see "
light flashes alternately green and orange. This
151HPower Problems”.
4.8 Replacing the Battery
Figure 4 1 Accessing the Battery Compartment
4.8.1 Removing the Battery
CAUTION: Before performing these procedures, turn off the computer, disconnect the AC adapter from the electrical outlet and the computer, disconnect the modem from the wall connector and computer, and remove any other external cables from the computer.
CAUTION: Using an incompatible battery may increase the risk of fire or explosion. Replace the battery only with a compatible battery purchased from Dell. The battery is designed to work with your computer. Do not use a battery from other computers with your computer.
NOTICE: You must remove all external cables from the computer to avoid possible connector damage. For
information about replacing the second battery, if applicable, see "
The following is applicable to UL 1604 and CSA C22.2 No. 213 compliant systems:
WARNING - Explosion Hazard - Do not disconnect equipment unless power has been removed or the area is known to be non-hazardous
WARNING - Explosion Hazard - Do not utilize any of the connectors/hubs unless area is known to be non-hazardous
To remove the battery:
If the computer is connected to a docking device (docked), undock it. See the documentation that came with your
1. docking device for instructions.
Ensure that the computer is turned off.
2.
If the 2 screws that secure the quarter-turn latches are installed, remove the 2 screws on the latches on the
3. battery compartment using a #1 Philips screw driver. See “ compartment. If the 2 security screws are not installed, proceed to step 4.
Lift each latch and turn each a quarter-turn, toward the ‘unlock’ icon, to release the latching mechanism. Remove
4. the compartment cover from the computer.
To remove the battery from the compartment, utilize the tab on the battery to assist in lifting the battery from the
5. compartment.
To replace the battery, follow the removal procedure in the reverse order.
152HXBay".
153HBottom View” for the location of the battery
4.9 Storing a Battery
Remove the battery when you store your computer for an extended period of time. A battery discharges during prolonged storage. After a long storage period, recharge the battery fully (see "
154HCharging the Battery") before you use it.
4.10 Battery Errors
To address error codes generated by the battery, refer to "155HError Messages".
5 Using the Keyboards
The XTG D630 notebook provides you the choice between the standard sealed, full-sized keyboard or the sealed, full-
sized, backlit, rubber keyboard.
5.1 Numeric Keypad
5 1 Keyboard Numeric Pad
The numeric keypad functions like the numeric keypad on an external keyboard. Each key on the keypad has multiple functions. The keypad numbers and symbols are marked in blue on the right of the keypad keys. To type a number or symbol, hold down <Fn> and press the desired key.
To enable the keypad, press <Num Lk>. The light indicates that the keypad is active. To disable the keypad, press <Num Lk> again.
5.2 Key Combinations
Keyboard Illumination <Fn> and right-arrow key Toggles the keyboard illumination lights on and off.
System Functions <Ctrl><Shift><Esc> Opens the Task Manager window.
Battery <Fn><F3> Displays the Dell™ QuickSet Battery Meter
156HDell™ QuickSet Battery Meter").
(see "
Display Functions <Fn><F8> Switches the video image to the next display option. The options
include the integrated display, an external monitor, and both displays simultaneously.
<Fn><F7> Scales between wide-screen and standard aspect ratio video
resolutions.
<Fn> and left-arrow key Activates the ambient light sensor, which controls brightness of the
display based on light level in the current environment.
<Fn> and up-arrow key Increases brightness on the integrated display only (not on an external
monitor).
<Fn> and down-arrow key Decreases brightness on the integrated display only (not on an external monitor). Power Management <Fn><Esc> Activates a power management mode. You can reprogram this
keyboard shortcut to activate a different power management mode
using the Advanced tab in the Power Options Properties window
157HAccessing Power Options Properties").
(see "
<Fn><F1> Puts the computer into hibernate, or sleep, mode. Dell QuickSet is
required (see "
158HDell™ QuickSet").
Microsoft® Windows® Logo Key Functions
Support Center (click Start Help and Support).
Windows logo key and <m> Minimizes all open windows. Windows logo key and <Shift><m> Restores all minimized windows. This key combination
functions as a toggle to restore minimized windows following the use of the
Windows logo key and <m> key combination. Windows logo key and <e> Runs Windows Explorer. Windows logo key and <r> Opens the Run dialog box. Windows logo key and <f> Opens the Search Results dialog box. Windows logo key and <Ctrl><f> Opens the Search Results-Computer dialog box (if the
computer is connected to a network). Windows logo key and <Pause> Opens the System Properties dialog box. To adjust keyboard operation, such as the character repeat rate, open the Control Panel, click Printers and Other
Hardware, and click Keyboard. For information about the Control Panel, access the Help and Support Center (click
Help and Support).
Start
5.3 Touch Pad and Track Stick
The touch pad detects the pressure and movement of your finger to allow you to move the cursor on the display. Use the touch pad and touch pad buttons as you would use a mouse.
NOTE: The track stick is only supported on the standard keyboard.
Figure 5 2 Touch Pad and Track Stick
1
·
·
· To select and move (or drag) an object, position the cursor on the object and tap twice on the touch pad. On the
·
You can also use the track stick to move the cursor. Press the track stick left, right, up, and down to change the direction of the cursor on the display. Use the track stick and the track stick buttons as you would use a mouse.
Touch pad buttons / Track stick buttons
To move the cursor, lightly slide your finger over the touch pad. To select an object, lightly tap once on the surface of the touch pad or use your thumb to press the left touch-pad
button.
second tap, leave your finger on the touch pad and move the selected object by sliding your finger over the surface.
To double-click an object, position the cursor on the object and tap twice on the touch pad or use your thumb to
press the left touch-pad button twice.
2 Touch Pad 3 Track stick
5.3.1 Customizing the Touch Pad and Track Stick
You can use the Mouse Properties window to disable the touch pad and track stick or adjust their settings.
Open the Control Panel, and then click Mouse. For information about the Control Panel, access the Help and
1.
2.
In the Mouse Properties window:
· Click the Device Select tab to disable the touch pad and track stick.
·
Click the Touch Pad tab to adjust touch pad and track stick settings.
3. Click OK to save the settings and close the window.
5.3.2 Changing the Track Stick Cap
You can replace your track stick cap if it wears down from prolonged use. Contact Dell Customer Support.
Pull the cap off the track stick.
1.
Align the new cap over the square track stick post and gently press the cap down onto the post.
2.
NOTICE: The track stick can damage the display if it is not properly seated on the post.
Test the track stick to ensure that the cap is seated properly.
3.
5.4 Backlight Control for Optional Backlit Keyboard
The backlit, rubber, sealed full-sized keyboard provides a key to allow you to control when the backlight feature is on or off. The Backlight Control Button is located near the cursor control keys on the lower right side of the keyboard.
Figure 5 3 Backlit Keyboard Backlight Control
Backlight Control
Backlight Control Toggles the keyboard backlight on and off.
6 Using the DirectVue Displays
The XFR D630 is available in two display configurations; the standard DirectVue Display as well as the optional DirectVue Touch Display.
6.1 Adjusting Brightness
When your computer is running on battery power, you can conserve power by setting the brightness to the lowest comfortable setting by pressing <Fn> and the up- or down-arrow key on the keyboard.
NOTE: Brightness key combinations only affect the display on your portable computer, not monitors or projectors that you attach to your portable computer or docking device. If your computer is connected to an external monitor and you try to change the brightness level, the Brightness Meter may appear, but the brightness level on the external device does not change.
You can press the following keys to adjust display brightness:
Press <Fn> and the up-arrow key to increase brightness on the integrated display only (not on an external
·
monitor).
· Press <Fn> and the down-arrow key to decrease brightness on the integrated display only (not on an external monitor).
6.2 Using the Ambient Light Sensor
The ambient light sensor is located on the bottom of the computer display panel. The ambient light sensor detects available environmental light and automatically increases or decreases the display backlighting to compensate for low­light and high-light environments.
You can enable or disable the ambient light sensor by pressing the <Fn> and left-arrow key combination.
NOTE: Do not cover the ambient light sensor with any adhesive labels. If covered up, the ambient light sensor
automatically sets the display brightness to the minimum level.
Figure 6 1 Ambient Light Sensor Location
1 Ambient light sensor
The ambient light sensor is disabled when your computer is shipped to you. If you enable the ambient light sensor and then use any of the display brightness key combinations, the ambient light sensor is disabled and the display brightness is increased or decreased accordingly.
Dell™ QuickSet allows you to enable or disable the ambient light sensor. You can also adjust maximum and minimum brightness settings that are activated when you enable the ambient light sensor feature. For more information about QuickSet, right-click the QuickSet icon in the taskbar, and click Help.
NOTE: Rebooting the computer returns the ambient light sensor to the last setting of enabled or disabled. NOTE: The ambient light sensor adjusts the display backlighting on your portable computer only. It does not
control the brightness on any external monitors or projectors.
6.3 Switching the Video Image
When you start the computer with an external device (such as an external monitor or projector) attached and turned on, the image may appear on either the computer display or the external device.
Press <Fn><F8> to switch the video image between the display only, the external device only, or the display and the external device simultaneously.
6.4 Setting Display Resolution and Refresh Rate
To display a program at a specific resolution, both the graphics card and the display must support the program, and the necessary video drivers must be installed.
Before you change any of the default display settings, make a note of the default settings for future reference.
NOTE: Use only the pre-installed video drivers, which are designed to offer the best performance with your pre­installed operating system.
If you choose a resolution or color palette that is higher than the display supports, the settings adjust automatically to the closest supported values.
Click the Start button and click Control Panel.
1.
Under Pick a category, click Appearance and Themes.
2.
Under Pick a task..., click the area you want to change, or under or pick a Control Panel icon, click Display.
3.
In the Display Properties window, click the Settings tab.
4.
Try different settings for Color quality and Screen resolution.
5.
NOTE: As the resolution increases, icons and text appear smaller on the screen.
If the video resolution setting is higher than that supported by the display, the computer enters pan mode. In pan mode,
the entire screen cannot be displayed at one time. For example, the taskbar that usually appears at the bottom of the
desktop may no longer be visible. To view the rest of the screen, use the touch pad or track stick to pan up, down, left, and right.
NOTICE: You can damage an external monitor by using an unsupported refresh rate. Before adjusting the refresh rate on an external monitor, see the user’s guide for the monitor.
6.5 Dual Independent Display Mode
You can attach an external monitor or projector to your computer and use it as an extension of your display (known as "dual independent display" or "extended desktop" mode). This mode allows you to use both screens independently and drag objects from one screen to the other, effectively doubling the amount of viewable work space.
Connect the external monitor, TV, or projector to the computer.
1.
Under Pick a category, click Appearance and Themes.
2.
Under Pick a task..., click the area you want to change, or under or pick a Control Panel icon, click Display.
3.
In the Display Properties window, click the Settings tab.
4.
NOTE: If you choose a resolution or color palette that is higher than the display supports, the settings adjust automatically to the closest supported values. For more information, see your operating system documentation.
Click the monitor 2 icon, click the Extend my Windows desktop onto this monitor check box, and then click
5. Apply.
Change Screen resolution to the appropriate sizes for both displays and click Apply.
6.
If prompted to restart the computer, click Apply the new color setting without restarting and click OK.
7.
If prompted, click OK to resize your desktop.
8.
If prompted, click Yes to keep the settings.
9.
Click OK to close the Display Properties window.
10.
To disable dual independent display mode:
Click the Settings tab in the Display Properties window.
1.
Click the monitor 2 icon, uncheck the Extend my Windows desktop onto this monitor option, and then click
2. Apply.
If necessary, press <Fn><F8> to bring the screen image back to the computer display.
6.6 Swapping Primary and Secondary Displays
To swap your primary and secondary display designations (for example, to use your external monitor as your primary display after docking):
Click the Start button and click Control Panel.
1.
Under Pick a category, click Appearance and Themes.
2.
Under Pick a task..., click the area you want to change, or under or pick a Control Panel icon, click Display.
3.
4. Click the Settings tab Advanced Displays tab.
See the documentation that came with your video card for additional information.
6.7 DirectVue™ Touch Display Information
If you purchased your XFR D630 Fully Rugged Notebook with the optional DirectVue Touch Display please review the following user instructions and tips.
The XFR D630 provides an optional touch screen display for entering and selecting data using an approved pointing device such as your finger, a passive stylus or any non-abrasive smooth blunt object that will not damage the touch display.
NOTICE: To ensure you properly care for and maintain your touch display, please refer to 159HCleaning Your Computer and adhere to the care instructions regarding the display.
CAUTION: The optional DirectVueTM Touch Display has been designed to accept finger touch as well as passive stylus input directly onto the screen. With the optional DirectVueTM Touch Display, a
stylus is included with the XFR D630 for use in selecting items on the touch screen. Other pointing devices can be used with the touch screen such as any non-abrasive, smooth or blunt object that will not damage the touch screen display. The touch screen surface can be damaged by ink pens, marker
pens or other pointed or abrasive objects. The use of non-approved input devices that cause damage
to the digitizer or LCD may not be covered by the limited warranty.
The touch screen is pre-configured and pre-calibrated at the factory, but may require further calibration to improve accuracy for entering or selecting data on the touch display. Please see the
160HTools section for information on Calibrating
your XFR D630 Touch Display and using your stylus.
6.7.1 Accessing Drivers and Documentation
Your XFR D630 DirectVue Touch Display’s drivers, touch-input parameters and documentation have been pre-loaded at the factory. For experienced users or IT administrators - if you need to re-install drivers, set up your XFR D630 Touch Display or modify parameters please refer to the pre-loaded XFR D630 Touchkit Utility documentation for detailed instructions and refer to the summary provided in
161HTouchkit Configuration Utility.
You can launch the pre-loaded documentation by selecting Start -> Programs -> Touchkit -> Document.
6.7.2 Touchkit Configuration Utility
Your XFR D630 DirectVue Touch Display system incorporates EETI technology. Touchkit is a software utility tool that allows you to configure various touch features. You can launch Touchkit by clicking Start -> Programs -> Touchkit -> Configure Utility.
NOTE: The touch screen is pre-configured and pre-calibrated at the factory, but may require further calibration to improve accuracy for entering or selecting data on the touch display, or to further configure it to your specific application.
Please refer to the pre-loaded documentation for the Touchkit Configuration Utility for a complete description of all its capabilities and functionality.
You can launch the pre-loaded documentation for the Touchkit Configuration Utility by selecting Start -> Programs -> Touchkit -> Document -> User Guide for Windows 2000/XP -> Touchkit Utility.
The Touchkit software utility consists of tabs that allow you to determine the best settings for your touch screen configuration.
The 162HGeneral tab shows all of the touchkit touch screen controllers installed in your system
·
·
The 163HTools tab provides access to calibration and touch position tools.
·
The 164HSetting tab provides access to the configuration of beeps, clicks and mouse emulation as well as selection of
9 point or 25 point calibration for linearization.
· The 165HDisplay tab provides the tools for mapping the touch screen area to specific areas of the display. The default is full screen.
· The 166HEdge Paramaters tab provides configuration for selecting items near the edge of the touch screen.
·
The 167HHardware tab provides the model and firmware version of the Touchkit touch screen controller.
·
The 168HAbout tab provides the version of the Touchkit driver as well as providing a link for downloading the latest
driver.
6.7.2.1 General
The general property page shows all the Touchkit touch screen controllers installed including RS232, USB and PS2 interfaces. The XFR D630 touch screen controller is a USB device.
6.7.2.2 Tools
window to guide you through the 9 or 25 points calibration. Configuring the function for 9 or 25 points calibration is
The Tools property page provides the following information and functions which are selected by pressing the push buttons. NOTE: Your touch screen is configured and calibrated at the factory. However, if you notice that the calibration is not as
precise as you would like, you can use the 4 Points Calibration and/or the Linearization tool to provide a more accurate alignment of the touch screen.
Graph of the Linearization Curve of the touch screen – for reference and troubleshooting purposes. See its
·
usage in the discussion of the Linearization function.
· 4 Points Calibration – Calibration aligns the touch panel with the video screen. The touch screen must be calibrated to allow for positional accuracy of the stylus or finger touch inputs.
· Clear and Calibrate – Clears the calibration/linearization parameters and allows you to perform the 4 points calibration again.
· Linearization (9 or 25 points linearization is set within the 169HSetting tab) – the linearization function provides for more precise mapping of the stylus or finger touch inputs. After linearization is completed, the linearity of the touch screen will be shown in the Linearization Curve window.
Draw Test - used for accuracy and performance checking.
·
.
1. 4 Points Calibration
The touch screen must be calibrated before it can work accurately. This function pops up a new window to guide you through the 4 points calibration. You should follow the guide to touch and hold the blinking X symbol in the calibration window until it does not blink to make sure that the utility can gather enough data for computation. In addition, a time line bar is shown in the bottom of the window to indicate time elapsed. If the touch screen is not touched before the time line bar reaches the right end, the calibration task will be terminated automatically.
2. Linearization
This function provides for more accurate touch screen positional alignment. The linearization function pops up a new
accessed in the
170H
Setting tab. You should follow the guide to touch and hold the blinking X symbol in the calibration
window until it does not blink to make sure that the utility can gather enough data for computation. In addition, a time line bar is shown in the bottom of the window to indicate the time elapsed. If the touch screen is not touched before the time line bar reaches the right end, the calibration task will be terminated automatically.
Draw Test
1.
This function is used for accuracy and performance checking. You can use the stylus or finger touch to draw or write across the displayed area.
You can press the Clear button to clear the window. Press the Quit button to terminate the draw test.
6.7.2.3 Setting
The Setting property page provides the following buttons and check boxes:
Beep
1.
· Beep On Touch
Check this check box to enable driver to generate a beep sound when touch touchscreen state is switched from untouched to touched state.
Beep On Release
·
Check this check box to enable driver to generate a beep sound when touchecreen state is switched from touched state to untouch state.
Frequency
·
Adjust this frequency to control the beep sound frequency generated by the driver.
· Duration
Adjust this duration to control the beep sound duration.
Linearization Style
2.
The Touchkit utility provides you with both 9 points and 25 points calibration for linearization. You can select the suitable kind of linearization type with this setting. The Linearization function is accessed under the
171HTools tab.
Double Click Time
3.
The double Click Time group is used to set system double click time. Changing this value will affect the double click behavior for all of the mice devices in the system. Two continuous clicks at the same area within this specified time period will be recognized as a double click event.
Double Click Area
4.
The double click area group is used to set the system double click area. Changing this value will affect the double click behavior for all of the mice devices in the system. Two continuous clicks within the specified area in the specified double click time will be recognized as a double click event.
Mouse Emulation mode
5.
There are 5 mouse emulation modes for the Touchkit touch screen controllers. Press on the button to change the emulation mode.
Normal Mode
·
You can select this mode to select objects, and drag objects.
· Click On Touch
With this Click On Touch mode, the driver emulates a mouse click event when the touch screen state is switched from un-touched state to touched state. Then, the driver always generates a mouse move event and tracks the touch position until the touch screen state switches to the un-touch state.
Click On Release
·
With this Click On Release mode, the driver emulates a mouse click event when the touch screen state is switched from touched state to un-touched state.
Click On Touch without moving cursor
·
With this mode, the driver behaves similarly to the Click On Touch mode. The cursor does not move to the touch position except for the first touch point.
Click On Release without moving cursor
·
With this mode, the driver behaves similarly to the Click On Release mode. The cursor does not move to the touch position except for the lift-off point.
Option
6.
You can access advanced configuration functions with the Option button. Press the button, and the following window will appear.
Loading...
+ 76 hidden pages