Daewoo DWF-800MP User Manual
INSTRUCTION MANUAL
Model: DWF-800MP
T ABLE OF CONTENTS
■ SAFETY INSTRUCTION &
SPECIFICA TIONS......................................2
■ P AR TS DESCRIPTIONS............................3
■ DIRECTIONS FOR SAFE USE..................4
•How To Install............................................4
•Water Connection......................................6
•Drain Hose Setting....................................7
■ HOW TO OPERATE...................................8
•Preparation for Washing............................8
•Descriptions of Control Panel....................9
•General Procedures for Operation..........10
•Guides for Basic Washing Programs......11
•Partial Process of Combination...............13
■ PERIODIC MAINTENANCE.....................14
■
SPECIAL GUIDES FOR REMOVING ST AINS
...16
■ TROUBLE SHOOTING GUIDES.............17
*
PLEASE READ CAREFULLY THIS INSTRUCTION
MANUAL BEFORE USING YOUR WASHER AND SAVE
THIS FOR FUTURE REFERENC
E.
DWF-800MP(¿ ) 01.3.26 9:57 PM ˘`1
2
SAFETY INSTRUCTIONS & SPECIFICATIONS
SAFETY INSTRUCTIONS
❐
Your safety is important to us.
Read all instructions before using your washer.
SPECIFICATIONS
❐
The above specifications and features are subject to change without prior notice.
☞
Do not wash items cleaned, washed, soaked in, or spotted with wax, paint, gasoline, oil, or other
flammable fluids. The fumes can create a fire hazard or explosion.
☞
Flammable fluids (dry-cleaning solvents, kerosene, gasoline, etc.) should not be used or stored in or near
your washer. Do not add flammable fluids to your wash water. These substances give off vapors that can
create a fire hazard or explosion.
☞
Do not allow children to operate, play with, or crawl on or inside your washer.
Supervise children closely when your washer is used near them.
☞
Do not reach into the wash tub unless START/HOLD button is pressed and all motion stops, while spinning.
☞
Do not use chlorine bleach and ammonia or acids (such as vinegar or rust remover) in the same wash.
Hazardous fumes can form.
☞
Unplug power supply cord before attempting to service your washer.
☞
Do not pour water on the control panel.
☞
Remove foreign objects (such as coin, pin, knife, other metallic materials, etc.) inside your wash load.
They may damage any fabric.
☞
Do not overload your washer to avoid poor cleaning, wrinkling and/or any abnormal operation.
DWF-800MP
Please refer to the rating label at the back of your washer
320W
525X535
858
29
6.0kg
Anti-Rust Stainless Steel
Approx. 130 Liters/Cycle
Please refer to the rating label at the back of your washer.
4 Programs
High (55 Liters), Medium (45 Liters), Low (31 Liters)
Backward
0.3Kgf/cm
2
~8Kgf/cm2(2.94N/cm2~78.4N/cm2)
Provided with 6 Spouting Holes for Powerful Upward Water Stream
1. Air Bubble Generator
2. Reserved Washing with Display for remaining time
3. Signal Buzzer for the Operation of Control Button
Only in Pump Model identified with ‘P’ added to Model No.
MODEL NO
Power Source
Power Consumption
Width X Depth (mm)
Height (mm)
Net Weight (Kg)
Maximum Mass of Textile
Material of Internal Tub
Water Consumption
Washing Capacity
Washing Program
Water Level
Direction of Inlet Valve
Operating Water Pressure
Pulsator
Optional Features
Coin Filter
DWF-800MP(¿ ) 01.3.26 9:57 PM ˘`2
3
PARTS DESCRIPTIONS
❐
The drawings in this book may vary from your washer model. They are designed to show the
different features of all models covered by this book. Y our model may not include all features.
ACCESSORIES (Full Option)
Hose Adapter
Drain Hose
Under Cover
Inlet Hose
Hose Clamp
In case of screw-shaped inlet hoses
water tap adapters will not be provided.
UP
FABRIC SOFTNER INLET
(Symbol, See page 10)
DETERGENT CASE
(Symbol )
CONTROL PANEL
(88 display and some
buttons may be excluded)
WASH TUB
PULSATOR
LIQUID BLEACH INLET
(Symbol See page 10)
BASE
(Height is optional)
GROUND WIRE
(This will not be
provided in
case of 3-wire
power cord)
ADJUSTABLE LEG
(Optional)
WATER CONNECTOR
(Blue Color : Cold,
Pink Color : Hot)
PLUG
DRAIN HOSE
LINT FILTER
DOOR
DWF-800MP(¿ ) 01.3.26 9:57 PM ˘`3
4
DIRECTIONS FOR SAFE USE
HOW TO INSTALL
Location
Place your washer on a level and solid floor,
Considering the length of inlet hose, drain
hose and power supply cord.
Do not place or store your washer below 0˚C(32˚F) to avoid
any damage from freezing.
Do not place your washer where it may be splashed during
bathing.
Installation of the Under Base Cover(Option)
After installing the washing machine,
assemble the under-base cover.
If washer is not level, it should be corrected by
the adjustable leg (provided optionally) in the
front-right side under the base and/or, a thin
block or brick.
NOTES:
The opening muse not be obstructed by carpeting
when the washing machine is installed on a
carpeted floor.
1
Before installing your washer, remove the
pad from the bottom of the cabinet. Then,
separate under cover from rear side of
cabinet by unscrewing and insert it into the
base.
2
Push the under-base cover into the end,
which decrease the noise made by this
washer.
1
After the packing box is opened, there is a
under-base cover at the top of the washer.
2
Push the under-base cover into the end,
which decrease the noise made by this
washer.
DWF-800MP(¿ ) 01.3.26 9:57 PM ˘`4
SCREW
5
Power Supply
• Before plugging the plug into wall receptacle,
check the voltage rating is in the range of
rating, marked on the label at the back side of
your washer.
Grounding
• If your water tap or water
pipe is not made of metal,
connect the ground wire to
a copper plate or a metal
rod and bury it in the earth.
• If both your water tap and
water pipe are made of
metal, connect the ground
wire to the base of the water
tap.
• It is of no use connecting the
ground wire to the water pipe
made of plastic.
• In case of using 3-core
cord, there is no need for
grounding.
Never Connect the Ground Wire to Such a Thing
• Never connect it to a gas pipe because of
danger of a explosion.
Gas Pipe
• Never connect it to a telephone wire or a
lightning rod because of os very dangerous
at a thunderbolt.
Telephone Wire
LABEL
20Cm
DWF-800MP(¿ ) 01.3.26 9:57 PM ˘`5
SCREW
6
1 Pull down the collar of the
inlet hose to separate it from
the hose adapter.
4 Remove the tape, and
screw connector B into
connector A tightly.
2 Loosen the four screws
properly in fitting into water
tap.
5 Connect the inlet hose to
the hose adapter, pulling
down the collar of hose end.
3
Fit the hose adapter into the water
tap and tighten the four screws
evenly while pushing up the
adapter so that the rubber packing
can stick to the water tap tightly.
6 Connect the opposite end of
the hose to water inlet of
your washer tightly.
• Please check the rubber
packing is inside the hose
end.
1 Connect the inlet
hose to the
thread of water
tap or water pipe
by tightening.
2 For the opposite
end, connect it
to water inlet as
the above
procedure 6.
WATER CONNECTION
Be careful not to confuse hot water inlet (pink color) and cold water inlet (blue color), if your
washer is provided with dual water inlets.
Also if you have only one water tap, connect the inlet hose with cold water inlet (blue color).
For normal tap
❐
In case that your washer is not provided with collar compartment, procedure 3 and 5 is
not necessary.
For Thread-Fitting Type
Leak Test
Turn on the water completely to check for any leakage. If any leakage, turn off the water, try
again as the above procedures.
For the special tap, call a qualified plumber for the installation.
Connector
Connector Hose
connector A
connector B
TAPE
DWF-800MP(¿ ) 01.3.26 9:57 PM ˘`6
TAPE
Connector A
Connector B
Rubber
Connector D
Inlet Hose
Packing
Connector C
Loading...