Daewoo DTC-1420, DTC-20D9, DTC-2120, DTC-21U8, DTC-2131 Service Manual

Service Manual

COLOR TELEVISION

CHASSIS : CM-907S

Model : DTC-14D9/20D9/21D9 ME/MP/MT/MZ

S/M No. : TCM907SEF0

Dec. 2002

DAEWOO ELECTRONICS Crop.

http : //svc.dwe .co.kr

DTC-14D2/21D2 ME/MP/MT/MZ
DTC-1420/2120 ME/MP/MT/MZ
DTC-21U8/2131/2132 ME/MP/MT/MZ

MODEL

ME
MP
MT
MZ

TEXT

O

X

O

X

PIP

O
O

X
X

MODEL OPTION LIST

✔

Caution

: In this Manual, some parts can be changed for improving, their
performance without notice in the parts list. So, if you need the
latest parts information,please refer to PPL(Parts Price List) in
Service Information Center (http://svc.dwe.co.kr).

-1-

1. SPECIFICATIONS 2

2. SAFETY INSTRUCTION

3

3. CIRCUIT BLOCK DIAGRAM

4

4. ALIGNMENT INSTRUCTIONS

5

5. CM-907S TYPICAL SERVICE DATA

11

6. ELECTRICAL PARTS LIST

13

7. EACH MODEL PARTS LIST

20

8. SCHEMATIC DIAGRAM

21

9. PRINTED CIRCUIT BOARD

22

10. MECHANICAL EXPLODED VIEW AND PARTS LIST

23

11. IC DESCRIPTION 27

12. TROUBLE SHOOTING CHARTS

44

TTABLE OF CONTENTS

ABLE OF CONTENTS

APPENDIX (“Appendix is provided only by internet [http://svc.dwe.co.kr]”)

APPENDIX (“Appendix is provided only by internet [http://svc.dwe.co.kr]”)

-2-

1. SPECIFICATIONS

Items Model DTC-14D9/20D9/21D9 ME/MP/MT/MZ

DTC-14D2/21D2 ME/MP/MT/MZ
DTC-1420/2120 ME/MP/MT/MZ
DTC-21U8/2131/2132 ME/MP/MT/MZ

TV Standard Color system PAL/SECAM, NTSC-4.43(AV)

Sound system B/G, D/K, I
Rated Voltage AC 100~250V, 50/60Hz
Power consumption 14”=80W, 20”=90W, 21”=95W, 21”(Flat)=95W
Sound Output Power 5W+5W(14”,20”), 7W+7W(21”,21”flat)

VHF-L : IC1-S6CH (43.25MHz~140.25MHz)

Channel Coverage VHF-H : IC1-S36CH (147.25MHz~423.25MHz)

UHF : S37-C57CH(431.25MHz~863.25MHz)
Tuning System FS Tuning System
Program No. Indication ON-Screen Display
Program Selection 100 Programs
Aux. Terminal AV input 1,2(front), DVD1, DVD2

AV output 1 (RCA) [TV signal]
Remote Control Unit R44C07

14” : 37Cm (Diagonal)
Screen size 20” : 48Cm (Diagonal)

21”, 21”flat : 51Cm (Diagonal)

BEFORE SERVICING THIS CHASSIS READ THE “X-RAY RADIATION PRECAUTIONS”,
“SAFETY PRECAUTIONS” AND “PRODUCT SAFETY NOTICE” BELOW.

-3-

2. SAFETY INSTRUCTION

NOTE

X-RAY RADIATION PRECAUTIONS

SAFETY PRECAUTIONS

PRODUCT SAFETY

1. Excessive high voltage can produce potentially hazard­ous X-RAY RADIATION. To avoid such hazards, the
high voltage must not exceed the specified limit. The
nominal value of the high voltage of this receiver is
25kV(21”) at max beam current. The high voltage must
not, under any circumstances, exceed 27kV(21”). Each
time a receiver requires servicing, the high volt-age
should be checked. It is recommended the reading

of the high voltage recorded as a part of the service
recorded as a part of the service records. It is important
to use an accurate and reliable high voltage meter.

2. The only source of

X-RAY RADIATION

in this TV
receiver is the picture tube. For continuous RADIATION
protection, the replacement tube must be exactly the
same type tube as specified in the “PART LIST”.

1. Potentials of high voltage are present when this receiver
is operating. Operation of the receiver outside the
cabinet or with the back cover removed involves a
shock hazard from the receiver.

1) Servicing should not be attempted by anyone who is not

thoroughly familiar with the precautions necessary
when working on high voltage equipment.

2) Always discharge the picture tube to avoid the shock

harzard before removing the anode cap.

3) Discharge the high potential of the picture tube before

handling the tube. The picture tube is highly evacuated
and if broken, glass fragments will be violently
expelled.

2. If any FUSE in this TV receiver is blown, replace it will
the FUSE specified in the “PART LIST”.

3. When replacing a high wattage resistor (oxide metal
film resistor) in circuit board, keep the resistor 10mm
away from circuit board.

4. Keep wires away from high voltage or high temperature
components.

5. This receiver must operate between AC 100-240
volts,50/60Hz. NEVER connect to DC supply or any
other power or frequency.

Many electrical and mechanical parts in this chassis have
special safety-related characteristics.
These characteristics are often passed unnoticed by a
visual inspection and the X-RAY RADIATION protection
afforded by them cannot necessarily be obtained by using
replacement components rated for higher voltage, wattage,
etc.
Replacement parts which have these special safety char­acteristics are identified in this manual and its supple-

ments, electrical components having such features are
identified by designated symbol on the “PART LIST”.
Before replacing any of these components, read the
“PARTLIST” in this manual carefully.
The use of substitute replacement part which do not have
the same safety characteristics as specified in the “PART
LIST” may created X-RAY RADIATION.

-4-

3. CIRCUIT BLOCK DIAGRAM

-5-

4. ALIGNMENT INSTRUCTIONS

1. SERVICE REMOCON & EEPROM PRESETTING DATA
1-1. SERVICE REMOCON : R-34SVC (S/N:48B3034SVC)
1-2. EEPROM PRESETTING DATA

KEY Name Details DEFAULT 14 /20 21 /21FLAT remark

S1 Heat-Run - - - ­S2 Screen - - - ­S3 Sound Test - - - ­S4 Picture Test - - - ­S5 BCL THD/GAIN - 130/12 110/12-130/12 145/12-145/12

V-CENTER 3700

V-SIZE 95

S6 Geometry H-CENTER 70

V LINEAR 16

S CORRECT 11

S7 PIP P H POS 45

P V POS 30

P R/G/B Peak 150/150/150

P CONT 04

P BRIGHT 01

S8 WHITE R/G/B DRIVE 170/170/170

BALANCE R/G/B BIAS 60/60/60

S9 SUB BRIGHT BRM 130 135 135

Sleep TXT TEST TXT ON/OFF
SIZE GAME TEST GAME ON/OFF

S11 OPTION PIP ON

DIGIT EYE ON

TEXT SEL OFF

LARGE OFF

VIDEO FRAME OFF

HOTEL VOL 0

HOTEL MODE OFF

S12 Shipping - -

For Sub-Bright

SVC Main Menu CONT 56 Adjust

Reference

For screen

IBRM 16

Adjust

Rdference

-6-

ALIGNMENT INSTRUCTIONS

SVC KEY EXPLAIN

(S5) BCL THD : MAX BEAM CURRENT ADJUST,DIFFERENT DATA FOR INCH.

BCL GAIN : AVERAGE BEAM ADJUST.

(S6) GEOMETRY : PAL (50Hz) adjust.

AV NTSC is auto correction.

---> H-CENTER(-1),V-SIZE(0),V-CENTER(+600),V-LINEARITY(-6)
S-CORRECTION(0),H-PALLEL(0)

(S10) NORMAL : PICTURE NORMAL data setting.
(SLEEP) : TXT CHECK ON LINE
(SIZE) : GAME FUNCTION CHECK ON LINE
(S11) OPTION

- HOTEL VOLUME : HOTEL MODE MAX VOL DATA SETTING

- HOTEL MODE OFF : ON--> VOL MAX SET& INSTALL DONT OPERATING

* Software option for Function Change

PIP (ON)

- ON : With PIP Models (DTC-xxxxME seiese)

- OFF : Without PIP Models (DTC-xxxxMT seriese)

Digital EYE (ON)

- ON : Enable the Digital Sensor (for all Model)

- OFF : Disable the Digital Sensor

LARGE (OFF)

- ON : For 29 inch Models CM-907

- OFF : For 14~21 inch Models CM-907S
LATIN : English,French,Swedish,Czech,German,Spanish,Italian,Estonian
EAST: English,Slovakian,Hungarian,Serbian,Albanian,Polish,Turkian,Rumanian
RUSSIA : English,Russian,Bulgaian,Ukrainian,Serbian,Montenegro

TEXT sel. (OFF) PERSIAN : English,Farsi

ARAB : English,Arabic
OFF : Teletext Language depends on OSD Language selection

Note : If OSD language & text selec. is different then Teletext depends on Text selec.

2.The confirmation of Protection circuit
Protection circuit confirmation is omitted in case of mass production in the factory

2-1. Over Current Protecor (OCP) circuit confirmation

2-1-1. Receive PAL RETMA PATTERN(signal of company:2CH., PAL-B) and adjust

STANDARD MODE in PICTURE.

2-1-2. Connect 1M

1/2W between BASE of Q801 and GND, to confirm operating of

PROTECTOR.

The next place, to confirm normal operation when the resister(1M

) is removed.

2-1-3. After Main Power Switch OFF/ON, to confirm normal operation of picture and sound

when turn the set on by remocon.

-7-

ALIGNMENT INSTRUCTIONS

3.The adjustment of SCREEN
3-1. Confirm the presetting

IBRM data of EEPROM according to CRT.
3-2. Press the [S2] KEY of SVC Remocon, horizontal line will be displayed.
3-3. Adjust SCREEN V/R of FBT so that the horizontal line reach the cut-off point.
3-4 To be completed adjustment of screen. Press the [S2] key to escape screen adjustment mode.

4.The adjustment of FOCUS
4-1. Receive PAL RETMA PATTERN(signal of company:2CH., PAL-B).
4-2. Adjust the picture to best distinct picture of 350 Line by revolve Focus Volume.

5.The adjustment of WHITE BALANCE
5-1. NITSUKI Setting : Set Nitsuki to the Auto Mode , Reference to the B , and System to the PAL .
5-2. Setting the Normal Stats

5-2-1. Adjust Picture to Normal mode.
5-2-2. Adjust the Gain of Nitsuki to suitability by manual when condition is Normal.

- Adjust the standard illumination take within limit bright of Nitsuki and luminosity
of SET into acount.

- Exhortative Standard illumination, : High 70Cd/

, LOW BEAM : about 15Cd/

5-2-3. Press the [S8]key of SVC remocon to adjustment of Whit Balance.

X=0.288, Y=0.301

5-2-4. Memorize in Nitsuki after Adjustment of White Balance.

5-3. Adjustment of White Balance

5-3-1.Receive Nitsuki signal.
5-3-2.Adjust Picture to Normal mode.
5-3-3.The Adjustment of High Beam : Adjust R-DRIVE and G-DRIVE to R,G,B BAR come to center.
5-3-4.The Adjustment of Low Beam : Adjust R-BIAS and G-BIAS to R,G,B BAR come to center.
5-3-5.Repeat 5-3-3 and 5-3-4 to R,G,B BAR come to within center

1.

6.The adjustment of GEOMETRY
6-1. Press the [S-6]key on the SVC remocon to call up the Geometry mode.

And then, Geometry OSD will be displayed.

6-1-1. All adjustment is base on PAL(50Hz),

but it can be base on NTSC(60Hz) in case of need.

6-2. The adjustment of VERTICAL CENTER

6-2-1.Receive PAL RETMA pattern(signal of company:PAL-B 2CH).
6-2-2.Press the PR up/down Keys(

) to select V CENTER.

Adjust with Vol Up/Down (

) keys so that the center mark of the CRT may be located on
the horizontal line in the middle of the pattern. In case of no center mark, adjust with
Vol Up/Down (

) keys to obtain a vertically symmetrical pattern.

-8-

ALIGNMENT INSTRUCTIONS

6-3. The adjustment of VERTICAL SIZE

6-3-1. Receive PAL RETMA pattern(signal of company:PAL-B 2CH).
6-3-2. Press the PR up/down Keys

to select V-SIZE.

Adjust with Vol Up/Down (

/ ) keys so that the upper and the lower of RETMA

pattern may be located at the boundaries of the screen.

6-4. The adjustment of HORIZONTAL CENTER

6-4-1. Receive PAL RETMA pattern(signal of company:PAL-B 2CH).
6-4-2. Press the PR up/down Keys (

/ ) to select V-SIZE.

Referring to the both side scales, adjust with Vol Up/Down (

/ ) keys

so that RETMA pattern may be symmetrical.

6-5. The adjustment of Vertical Linearity

6-5-1. Receive PAL CROSSHATCH pattern(signal of company:PAL-B 5CH).
6-5-2. Fix adjustment of Vertical Linearity after EEPROM presetting,

but it can be adjusted in case of need.

6-5-3. Press the PR up/down Keys (

/ ) to select V LINEAR.

Adjust Vertical Linearity with Vol Up/Down (

/ ) keys.

6-6. The adjustment of VERTICAL S-Correction

6-6-1. Receive PAL CROSSHATCH pattern(signal of company:PAL-B 5CH).
6-6-2. Fix adjustment of Vertical S-Correction after EEPROM DATA presetting,

but it can be adjusted in case of need.

6-6-3. Press the PR up/down Keys (

/ ) to select S CORRECT.

Adjust S-Corrction with Vol Up/Down (

/ ) keys.

-9-

ALIGNMENT INSTRUCTIONS

7. THE ADJUSTMENT OF SUB-PICTURE (SUB-BRIGHT,SUB-CONTRAST)
7-1. Receive PAL RETMA PATTERN(signal of company:2CH., PAL-B)
7-2. Press the [S9] KEY of SVC Remocon, BRM OSD wil be displayed.
7-3. The adjustment of SUB-BRIGHT

7-3-1. Press the PR up/down Keys (

/ ) to select SUB-BRIGHT in SUB-PICTURE MENU.

Adjust SUB-BRIGHT with Vol Up/Down (

/ ) keys.
7-3-2. Adjust With BRM, When SUB-BRIGHT is lacking in margin of adjustment.
7-3-3. Standard of adjustment : Adjust till instant of 1, 2th cordon disappear in

RETMA CONTRAST CHART(signal of company).

7-3-4. When Sub-Picture mode was exited after SUB

s adjustment, Normal vlaue is
brighter(about 18%) than adjustment-point(about 10%) of adjustment-mode because
BRIGHT is set to rise 2~3 step.

8. THE ADJUSTMENT OF PIP
8-1. Receive PAL RETMA pattern(signal of company:PAL-B 2CH) and Color Bar.
8-2. Press the [S7] KEY of SVC Remocon, PIP-Adjustment OSD wil be displayed.
8-3. Fix adjustment of PIP after EEPROM DATA presetting,

but it can be adjusted in case of need.
8-4. Adjust PIP after GEOMETRY, WHITE BALANCE and SUB-BRIGHT are adjusted.
8-5. List of adjustment

PIP H POSITON : Adjustment of H-position Sub-Picture,

(Reference : Presetting Value of EEPROM = 45)

PIP V POSITON : Adjustment of V-position of Sub-Picture,

(Reference : Presetting Value of EEPROM = 30)

PIP R/G/B Peak : Adjustment of Gain of PIP IC R,G,B Output

(Reference : Presetting Value of EEPROM = 130)

P CONTRAST : Adjustment of AC Gain(Contrast) of PIP IC RGB Output

(Reference : Presetting Value of EEPROM = 04)

P BRIGHT : Adjustment of DC Level(SUB BRIGHT) of PIP IC RGB Output

(Reference : Presetting Value of EEPROM = 00)

-10-

ALIGNMENT INSTRUCTIONS

9. REMOCON

9-1. SERVICE REMOCON 9-2. USER REMOCON

9-3. SERVICE REMOCON

1) Enter SERVICE MODE : Press keys of User Remocon, as follows.
Ch91, Sharpness 0, Skip(red), Move(green), Menu.

2) Choice SERVICE MENU : Pr-Up/Down

3) Enter SERVICE SUB MENU : Vol-Up/Down

S1 S2 S3

S4 S5 S6

S7 S8 S9

S11

RECALL

S10 S12

MUTE

POWER

TV/CATV

ADD/ERASE

TV/VIDEO

SOUND MODE

SURROUND

N

O

IS

E

C

L

E

A

R

CH

VOLVOL

CH

MENU

PIP M/S

CH

VOL

V­POSITION

POSITION

TV/VIDEO

PAUSE/

STILL

SIZE

SLEEP

1

3

R-34SVC

456

7

890

2

-11-

5. CM-907S TYPICAL SERVICE DATA

NO CH PATTERN BAND V.FREQ. Sound SYSTEM Color SYSTEM ADJUSTMENT

2 PAL H-2CH VL 64.25 BG PAL

7 PAL H-7CH VH 182.25 BG PAL

9 PAL H-9CH VH 196.25 BG PAL

10 PAL H-10CH VH 209.25 BG PAL

28 PAL H-28CH U 527.25 BG PAL

30 PAL-40CH W/B U 623.25 AUTO W/B

31 PAL-2CH RETMA VL 48.25 BG AUTO

FOCUS, V-CENTER, V-SIZE,V-SLOPE H-CENTER,SCREEN

32 PAL-47CH C/HATCH U 679.25 I AUTO “ CONVERGENCE, ADJUSTMENT”

33 PAL-10CH COLOR BAR VH 210.25 BG PAL “ SCREEN, AGC”

34 PAL-4CH DEM VL 62.25 BG PAL “ SOUND, Teletext check”

35 PAL-12CH PHILIPS VH 224.25 BG SECAM SECAM COLOR CHECK

36 PAL-18CH RETMA U 511.25 DK AUTO SOUND

CM-907S CHASSIS SETTING LIST

-12-

CM-907S TYPICAL SERVICE DATA

KEY Name Details remark

14” 20” 21” 21” F

S5 BCL THD/GAIN - 85 /12 130/12 140/12 145/12 WHITE PEAK : ON

WHITE PEAK ON

S6 Geometry H-CENTER 100 100 80 80

V-CENTER 3910 3850 3790 3520

V-SIZE 82 88 118 123
H-SIZE 1520 1520 NOT USE

PARA -122 -122 -122 -122 NOT USE

V-LINEARITY 11 11 16 16

S-CORRECTION 11 11 11 11

CORNER 120 120 120 120 NOT USE

H-BOW -517 -517 -517 -517 NOT USE

H-PARA 20 20 20 20 NOT USE

EW TRAP 121 121 121 121 NOT USE

S7 PIP P H POS 45

P V POS 30

P R/G/B Peak 130

P CONT 4

P BRIGHT 5

S8 WHITE R/G/B DRIVE 170/170/170 170/170/170

BALANCE R/G/B BIAS 60/60/60 60/60/60

S9 SUB BRIGHT BRM 135 135 135 135

S10 NORMAL BRIGHT 32

DATA CONTRAST 58

COLOR 32

SHARPNESS 48

S11 OPTION PIP ME/MP: ON, MT/MZ: OFF

DIGIT. EYE ON

TEXT SEL. TEXT OPTION

TELETEXT ME/MT: ON, MP/MZ: OFF

LARGE OFF

VID FRAME OFF

HOTEL VOL +00000

HOTELMODE OFF

S12 Shipping -

SVC Main Menu CONT 32

BRM 140

For Screen Adjust Reference

-13-

6. ELECTRICAL PARTS LIST

LOC PART CODE PART NAME DESCRIPTION REMARK

ZZ100 48B4844C07 TRANSMITTER REMOCON R-44C07 (AA)
ZZ110 PTACPWD691 ACCESSORY AS DTC-21D9ME
0100 4850Q00810 BATTERY R6P/LN
0200 48586054K1 MANUAL INSTRUCTION DTM-2082CW
M001 4858213801 BAG INSTRUCTION L.D.P.E T0.05X250X400
ZZ120 PTBCSHD691 COVER BACK AS DTC-21D9ME
M211 4852162401 COVER BACK HIPS BK 21D9
M781 4857817610 CLOTH BLACK FELT 300X20X0.7
ZZ130 PTPKCPD691 PACKING AS DTC-21D9ME
10 6520010100 STAPLE PIN AUTO W65
M801 4858059900 BOX CARTON SW-3
M811 4858100P00 PAD EPS 14D9
M821 4858219201 BAG P.E P.E FOAM T0.5X1100X950
ZZ131 48519A5310 CRT GROUND NET 2101S-1015-1P
ZZ132 58G0000147 COIL DEGAUSSING DC-21SF
ZZ140 PTCACAD691 CABINET AS DTC-21D9ME
40 2TF01612CL TAPE FILAMENT 0.15X12mmX55mm
M201A 4856013300 SCREW CRT FIXING 30X80 BK
M201B 4856215404 WASHER RUBBER CR T4.0
M201C 4856013302 SCREW CRT FIXING 30X190 BK
M211A 7172401412 SCREW TAPPTITE TT2 TRS 4X14 MFZN BK
M211B 7178301212 SCREW TAPPTITE TT2 WAS 3X12 MFZN BK
M541 4855415800 SPEC PLATE 150ART P/E FILM (C/TV)
M591A 4856013610 SCREW SPKR FIX L=16 A=17
M681 4856812001 TIE CABLE NYLON66 DA100
SP01A 7178301011 SCREW TAPPTITE TT2 WAS 3X10 MFZN
SP01B 7178301011 SCREW TAPPTITE TT2 WAS 3X10 MFZN
V901 4859630860 CRT A51EFK135X01
ZZ200 PTFMSJD691 MASK FRONT AS DTC-21D9ME
M191 4854953901 BUTTON CH ABS GY 21D9
M191A 7178301011 SCREW TAPPTITE TT2 WAS 3X10 MFZN
M201 4852082601 MASK FRONT HIPS GY 21D9
M481 4854863501 BUTTON POWER ABS GY 21D9
M481A 4856716000 SPRING SWPA PIE0.5
M531 4855548301 DECO SENSOR PC SMOG 21D9
M561 4855617500 MARK BRAND CU AU+ABS BK
M591 4855936101 DECO EYE ABS BLUE
M591B 7178301011 SCREW TAPPTITE TT2 WAS 3X10 MFZN
ZZ210 PTSPPWD691 SPEAKER AS DTC-21D9ME
P601A 4850704S31 CONNECTOR

YH025-04+YRT205+ULW800400
SP01 4858311110 SPEAKER 12W 8 OHM SP-58126F
SP02 4858311110 SPEAKER 12W 8 OHM SP-58126F
ZZ290 PTMPMSD691 PCB MAIN MANUAL AS DTC-21D9ME
10 2193102005 SOLDER BAR SN:PB=63:47 S63S-1320
30 2291050616 FLUX SOLDER JS-64T3
40 2291050301 FLUX SOLVENT IM-1000
C406 CMYH3C822J C MYLAR 1.6KV BUP 8200PF J
C408 CMYE2D514J C MYLAR 200V PU 0.51MF J
C801 CL1UC3104M C LINE ACROSS

WORLD AC250V 0.1UF M R.47
C804 CEYN2G181P C ELECTRO 400V LHS 180MF (25X35)
C806 CBYB3D152K C CERA SEMI 2KV BL(N) 1500PF K
C811 CH1BFE222M C CERA AC U/C/V AC400V 2200PF
D812 DRGP30J—- DIODE RGP30J
D814 DRGP30J—- DIODE RGP30J
F801 5F3GB4022L FUSE GLASS TUBE V/S TL 4A 250V MF51
HP01 4859102130 JACK EARPHONE YSC-1537
I301 PTA2SW7106 HEAT SINK ASS`Y 1LA78041— + 7174301011
00001 1LA78041— IC VERTICAL LA78041
0000A 4857027106 HEAT SINK SPCC T1.0+SN
0000B 7174301011 SCREW TAPPTITE TT2 RND 3X10 MFZN
I501 1V3834DW08 IC MICOM MCM VCT3834F-DW08

DTC-21D9ME

LOC PART CODE PART NAME DESCRIPTION REMARK

I601 PTA2SW8228 HEAT SINK ASS`Y 1TDA8946J- + 7174301211
00001 1TDA8946J- IC AUDIO AMP TDA8946J
0000A 4857028228 HEAT SINK AL EX BK
0000B 7174301211 SCREW TAPPTITE TT2 RND 3X12 MFZN
I602 1TDA7442— IC AUDIO PROCESSOR TDA7442
I701 124LC16B1B IC MEMORY 24LC16B1B
I801 PTA2SW7920 HEAT SINK ASS`Y 1STRF6656- + 7174301011
00001 1STRF6656- IC POWER STR-F6656
0000A 4857027920 HEAT SINK AL EX BK
0000B 7174301011 SCREW TAPPTITE TT2 RND 3X10 MFZN
I802 1LTV817C— IC PHOTO COUPLER LTV-817C
I803 1DP123—— IC ERROR AMP DP123
I804 PTZ2SW6900 HEAT SINK ASS`Y 1K1A7805P1 + 7174300811
00001 1K1A7805P1 IC REGULATOR KIA7805API
0000A 4857026900 HEAT SINK AL EX
0000B 7174300811 SCREW TAPPTITE TT2 RND 3X8 MFZN
I805 PTR2SW6900 HEAT SINK ASS`Y 1K1A7809P1 + 7174301011
00001 1K1A7809P1 IC REGULATOR K1A7809API
0000A 4857026900 HEAT SINK AL EX
0000B 7174301011 SCREW TAPPTITE TT2 RND 3X10 MFZN
I806 1LP295033- IC REGULATOR LP2950 3.3V
I901 PTA3SW1101 HEAT SINK ASS`Y 1TEA5101B- + 7174300811
00001 1TEA5101B- IC VIDEO AMP TEA5101B
0000A 4857031101 HEAT SINK A1050P-24 T=2.0
0000B 7174300811 SCREW TAPPTITE TT2 RND 3X8 MFZN
ID01 1PNA4603H- IC PHOTO SENSOR PNA4603H
IF01 1TS0P1238W IC PREAMP TS0P1238WI1
JP02 4859108450 JACK PIN BOARD YSC03P-4120-14A
JV01 4859110950 JACK PIN BOARD YS01-0001
JV02 4859111750 JACK PIN BOARD PH-JB-9515
L401 58H0000020 COIL H-LINEARITY L-76(76.5UH)
LF801 5PLF3143G- FILTER LINE LF-3143G
M351 DLH2PR5MHS LED HOLDER AS LH-2P-R-5M-H3
M371 4856815400 CLAMP WIRE NYLON 66
M372A 4853747800 RETA PCB NYLON 66
M372B 4853747800 RETA PCB NYLON 66
M373 4856812001 TIE CABLE NYLON66 DA100
P401 4859240120 CONN WAFER YFW500-06
P501A 4850706S18 CONNECTOR YH025-06+YST025+ULW=500
P502A 4850705S03 CONNECTOR

YH025-05+YBNH250+ULW=300
P904 4859281320 CONN WAFER TAC-L18X-A3
PDA01 4850703S18 CONNECTOR

YH025-03+YBNH250+ULW=200
PW801 4859902910 CORD POWER AS

KKP419C+BL102NG+TUBE=2100
Q401 PTJ2SW7200 HEAT SINK ASS`Y TST1803DH- + 7174301011
00001 TST1803DH- TR ST1803DHI
0000A 4857027200 HEAT SINK AL T1.0
0000B 7174301011 SCREW TAPPTITE TT2 RND 3X10 MFZN
R801 DDC7R0M290 POSISTOR ECPCD7R0M290
R803 RX10T109KS R CEMENT

10W 1 OHM K TRIPOD SMALL
SCT01 4859304130 SOCKET CRT ISHG93S
SW801 5S40101143 SW POWER PUSH PS3-22SP (P.C.B)
T401 50H0000231 FBT LTC-505
T402 50D10A3—- TRANS DRIVE TD-10A3
T801 50M4445B3- TRANS SMPS TSM-4445B3
TU01 4859723730 TUNER VARACTOR TMDG1-837
X501 5XE20R250E CRYSTAL QUARTZ HC-49/U 20.2500MHZ 30PPM
ZZ200 PTMPJ0D691 PCB MAIN (RHU) AS DTC-21D9ME
C310 CEXF1E102V C ELECTRO 25V RSS 1000MF (13X20) TP
C413 CEXF1E102V C ELECTRO 25V RSS 1000MF (13X20) TP
C419 CEXF1C471V C ELECTRO 16V RSS 470MF (8X12)TP
C420 CEXF2E220V C ELECTRO 250V RSS 22MF (13X20) TP

✔ Caution:In this Service Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the

latest parts information, please refer to PPL(Parts Price List) in Service information Center(http://svc.dwe.co.kr)

-14-

ELECTRICAL PARTS LIST

LOC PART CODE PART NAME DESCRIPTION REMARK

C424 CEXF1V471V C ELECTRO 35V RSS 470MF (10X20) TP
C541 CEXF1C471V C ELECTRO 16V RSS 470MF (8X12)TP
C631 CEXF1E222V C ELECTRO 25V RSS 2200MF (16X25) TP
C817 CEXF2C101V C ELECTRO 160V RSS 100MF (16X25) TP
C818 CEXF2C101V C ELECTRO 160V RSS 100MF (16X25) TP
C819 CEXF2A470V C ELECTRO 100V RSS 47MF (10X16) TP
C821 CEXF1C102V C ELECTRO 16V RSS 1000MF (10X20) TP
C908 CCXB3D102K C CERA 2KV B 1000PF K (TAPPING)
ZZ200 PTMPJBD691 PCB MAIN M-10 AS DTC-21D9ME
10 2TM18006BE TAPE MASKING 6.2X500
E001 4856310300 EYE LET BSR T0.2 (R1.6)
E002 4856310300 EYE LET BSR T0.2 (R1.6)
E003 4856310300 EYE LET BSR T0.2 (R1.6)
E005 4856310300 EYE LET BSR T0.2 (R1.6)
E006 4856310300 EYE LET BSR T0.2 (R1.6)
E008 4856310300 EYE LET BSR T0.2 (R1.6)
E009 4856310300 EYE LET BSR T0.2 (R1.6)
E010 4856310300 EYE LET BSR T0.2 (R1.6)
E011 4856310300 EYE LET BSR T0.2 (R1.6)
E012 4856310300 EYE LET BSR T0.2 (R1.6)
E013 4856310300 EYE LET BSR T0.2 (R1.6)
E014 4856310300 EYE LET BSR T0.2 (R1.6)
E015 4856310300 EYE LET BSR T0.2 (R1.6)
E017 4856310300 EYE LET BSR T0.2 (R1.6)
E020 4856310300 EYE LET BSR T0.2 (R1.6)
E021 4856310300 EYE LET BSR T0.2 (R1.6)
E022 4856310300 EYE LET BSR T0.2 (R1.6)
E023 4856310300 EYE LET BSR T0.2 (R1.6)
E024 4856310300 EYE LET BSR T0.2 (R1.6)
E025 4856310300 EYE LET BSR T0.2 (R1.6)
E026 4856310300 EYE LET BSR T0.2 (R1.6)
E027 4856310300 EYE LET BSR T0.2 (R1.6)
E028 4856310300 EYE LET BSR T0.2 (R1.6)
E029 4856310600 EYE LET BSR T0.2 (R2.3)
E030 4856310600 EYE LET BSR T0.2 (R2.3)
E031 4856310600 EYE LET BSR T0.2 (R2.3)
E032 4856310600 EYE LET BSR T0.2 (R2.3)
E033 4856310600 EYE LET BSR T0.2 (R2.3)
E034 4856310600 EYE LET BSR T0.2 (R2.3)
E035 4856310600 EYE LET BSR T0.2 (R2.3)
E036 4856310600 EYE LET BSR T0.2 (R2.3)
E037 4856310600 EYE LET BSR T0.2 (R2.3)
E038 4856310600 EYE LET BSR T0.2 (R2.3)
E039 4856310600 EYE LET BSR T0.2 (R2.3)
E040 4856310600 EYE LET BSR T0.2 (R2.3)
E041 4856310600 EYE LET BSR T0.2 (R2.3)
E043 4856310600 EYE LET BSR T0.2 (R2.3)
E046 4856310600 EYE LET BSR T0.2 (R2.3)
E048 4856310600 EYE LET BSR T0.2 (R2.3)
E050 4856310600 EYE LET BSR T0.2 (R2.3)
N001 4857417500 TERM PIN DA-IB0214(D2.3/DY PIN)
N002 4857417500 TERM PIN DA-IB0214(D2.3/DY PIN)
N003 4857417500 TERM PIN DA-IB0214(D2.3/DY PIN)
N004 4857417500 TERM PIN DA-IB0214(D2.3/DY PIN)
P501 485923192S CONN WAFER YW025-06 (STICK)
P502 485923182S CONN WAFER YW025-05 (STICK)
P601 485923172S CONN WAFER YW025-04 (STICK)
PD01 485923162S CONN WAFER YW025-03 (STICK)
R105 RS01Z472J- R M-OXIDE FILM 1W 4.7K OHM J (TAPPING)
R404 RS01Z751J- R M-OXIDE FILM 1W 750 OHM J (TAPPING)
R406 RS01Z103J- R M-OXIDE FILM 1W 10K OHM J (TAPPING)

LOC PART CODE PART NAME DESCRIPTION REMARK

R410 RS01Z229J- R M-OXIDE FILM 1W 2.2 OHM J (TAPPING)
R413 RS01Z100J- R M-OXIDE FILM 1W 10 OHM J (TAPPING)
R414 RS01Z472J- R M-OXIDE FILM 1W 4.7K OHM J (TAPPING)
R418 RS01Z249J- R M-OXIDE FILM 1W 2.4 OHM J (TAPPING)
R420 RS01Z519J- R M-OXIDE FILM 1W 5.1 OHM J (TAPPING)
R431 RS02Z200JS R M-OXIDE FILM 2W 20 OHM J SMALL
R804 RS02Z683JS R M-OXIDE FILM 2W 68K OHM J SMALL
R807 RF02Z158K- R FUSIBLE 2W 0.15 OHM K (TAPPING)
R813 RF02Z568K- R FUSIBLE 2W 0.56 OHM K (TAPPING)
R907 RS01Z683J- R M-OXIDE FILM 1W 68K OHM J (TAPPING)
R908 RS01Z683J- R M-OXIDE FILM 1W 68K OHM J (TAPPING)
R909 RS01Z683J- R M-OXIDE FILM 1W 68K OHM J (TAPPING)
ZZ200 PTMPJRD691 PCB MAIN RADIAL AS DTC-21D9ME
C104 CEXF1H101V C ELECTRO 50V RSS 100MF (8X11.5) TP
C105 CEXF1C331V C ELECTRO 16V RSS 330MF (8X11.5) TP
C108 CEXF1H479V C ELECTRO 50V RSS 4.7MF (5X11) TP
C301 CMXM2A473J C MYLAR 100V 0.047MF J (TP)
C302 CMXM2A103J C MYLAR 100V 0.01MF J (TP)
C303 CEXF1H100V C ELECTRO 50V RSS 10MF (5X11) TP
C304 CMXM2A123J C MYLAR 100V 0.012MF J (TP)
C305 CEXF1H101V C ELECTRO 50V RSS 100MF (8X11.5) TP
C307 CXSL2H100D C CERA 500V SL 10PF D (TAPPING)
C308 CMXM2A104J C MYLAR 100V 0.1MF J (TP)
C311 CEXF1H479V C ELECTRO 50V RSS 4.7MF (5X11) TP
C320 CEXD1H109Q C ELECTRO 50V RT 1MF (6.3X11) TP
C402 CCXF1H102Z C CERA 50V F 1000PF Z (TAPPING)
C403 CCXB2H222K C CERA 500V B 2200PF K (TAPPING)
C405 CEXF2A100V C ELECTRO 100V RSS 10MF (6.3X11) TP
C409 CEXF2C339V C ELECTRO 160V RSS 3.3MF (8X16) TP
C410 CCXB2H471K C CERA 500V B 470PF K (TAPPING)
C412 CCXB2H221K C CERA 500V B 220PF K (TAPPING)
C415 CEXF1E470V C ELECTRO 25V RSS 47MF (5X11) TP
C417 CMXM2A104J C MYLAR 100V 0.1MF J (TP)
C418 CMXM2A104J C MYLAR 100V 0.1MF J (TP)
C421 CCXB2H222K C CERA 500V B 2200PF K (TAPPING)
C502 CEXF1C221V C ELECTRO 16V RSS 220MF (8X11.5) TP
C503 CEXF1H100V C ELECTRO 50V RSS 10MF (5X11) TP
C505 CEXF1E470V C ELECTRO 25V RSS 47MF (5X11) TP
C507 CEXF1H109V C ELECTRO 50V RSS 1MF (5X11) TP
C508 CEXF1H109V C ELECTRO 50V RSS 1MF (5X11) TP
C509 CEXF1H109V C ELECTRO 50V RSS 1MF (5X11) TP
C510 CEXF1H109V C ELECTRO 50V RSS 1MF (5X11) TP
C511 CEXF1H109V C ELECTRO 50V RSS 1MF (5X11) TP
C512 CEXF1H109V C ELECTRO 50V RSS 1MF (5X11) TP
C514 CEXF1E470V C ELECTRO 25V RSS 47MF (5X11) TP
C518 CEXF1C331V C ELECTRO 16V RSS 330MF (8X11.5) TP
C520 CXCH1H151J C CERA 50V CH 150PF J (TAPPING)
C524 CEXF1E470V C ELECTRO 25V RSS 47MF (5X11) TP
C525 CEXF1H100V C ELECTRO 50V RSS 10MF (5X11) TP
C527 CXCH1H309C C CERA 50V CH 3PF C
C528 CXCH1H309C C CERA 50V CH 3PF C
C530 CEXF1H100V C ELECTRO 50V RSS 10MF (5X11) TP
C542 CEXF1E470V C ELECTRO 25V RSS 47MF (5X11) TP
C543 CCXF1H104Z C CERA 50V F 0.1MF Z
C544 CEXF1E470V C ELECTRO 25V RSS 47MF (5X11) TP
C545 CEXF1H339V C ELECTRO 50V RSS 3.3MF (5X11) TP
C551 CEXF1C221V C ELECTRO 16V RSS 220MF (8X11.5) TP
C575 CEXF1H220V C ELECTRO 50V RSS 22MF (5X11) TP
C581 CEXF1H100V C ELECTRO 50V RSS 10MF (5X11) TP
C582 CEXF1E470V C ELECTRO 25V RSS 47MF (5X11) TP
C583 CEXF1H100V C ELECTRO 50V RSS 10MF (5X11) TP

-15-

ELECTRICAL PARTS LIST

LOC PART CODE PART NAME DESCRIPTION REMARK

C584 CEXF1E470V C ELECTRO 25V RSS 47MF (5X11) TP
C585 CEXF1E470V C ELECTRO 25V RSS 47MF (5X11) TP
C606 CEXF1E470V C ELECTRO 25V RSS 47MF (5X11) TP
C611 CEXF1H479V C ELECTRO 50V RSS 4.7MF (5X11) TP
C612 CEXF1H479V C ELECTRO 50V RSS 4.7MF (5X11) TP
C615 CCXF1H104Z C CERA 50V F 0.1MF Z
C617 CMXM2A682J C MYLAR 100V 6800PF J (TP)
C618 CMXM2A682J C MYLAR 100V 6800PF J (TP)
C619 CEXF1H100V C ELECTRO 50V RSS 10MF (5X11) TP
C620 CMXM2A682J C MYLAR 100V 6800PF J (TP)
C621 CMXM2A682J C MYLAR 100V 6800PF J (TP)
C624 CMXL1J224J C MYLAR 63V MEU 0.22MF J (TP)
C625 CEXF1H220V C ELECTRO 50V RSS 22MF (5X11) TP
C626 CEXF1H339V C ELECTRO 50V RSS 3.3MF (5X11) TP
C627 CMXL1J224J C MYLAR 63V MEU 0.22MF J (TP)
C628 CMXL1J224J C MYLAR 63V MEU 0.22MF J (TP)
C629 CMXL1J224J C MYLAR 63V MEU 0.22MF J (TP)
C802 CCXF3A472Z C CERA 1KV F 4700PF Z (T)
C803 CCXF3A472Z C CERA 1KV F 4700PF Z (T)
C805 CEXF1H470V C ELECTRO 50V RSS 47MF (6.3X11) TP
C807 CEXF1H100V C ELECTRO 50V RSS 10MF (5X11) TP
C808 CMXM2A182J C MYLAR 100V 1800PF J (TP)
C809 CCXB3A471K C CERA 1KV B 470PF K (T)
C810 CCXB1H152K C CERA 50V B 1500PF K (TAPPING)
C812 CCXB3A471K C CERA 1KV B 470PF K (T)
C813 CCXB3A471K C CERA 1KV B 470PF K (T)
C814 CCXB3A471K C CERA 1KV B 470PF K (T)
C825 CEXF1H229V C ELECTRO 50V RSS 2.2MF (5X11) TP
C826 CEXF1H220V C ELECTRO 50V RSS 22MF (5X11) TP
C827 CEXF1H479V C ELECTRO 50V RSS 4.7MF (5X11) TP
C828 CEXF1C101V C ELECTRO 16V RSS 100MF (6.3X11) TP
C833 CEXF1C101V C ELECTRO 16V RSS 100MF (6.3X11) TP
C905 CMXL2E104K C MYLAR 250V MEU 0.1MF K
C906 CEXF1E470V C ELECTRO 25V RSS 47MF (5X11) TP
CS01 CEXF1H100V C ELECTRO 50V RSS 10MF (5X11) TP
CS02 CEXF1H100V C ELECTRO 50V RSS 10MF (5X11) TP
F801A 4857415001 CLIP FUSE PFC5000-0702
F801B 4857415001 CLIP FUSE PFC5000-0702
G901 4SG0DX0001 SPARK GAP SSG-102-A1(1.0KV) TAP
G902 4SG0DX0001 SPARK GAP SSG-102-A1(1.0KV) TAP
G903 4SG0DX0001 SPARK GAP SSG-102-A1(1.0KV) TAP
I702 1K1A7025AP IC RESET KIA7025AP
L812 58CX430599 COIL CHOKE AZ-9004Y 940K TP
Q101 TKTC3198Y- TR KTC3198Y
Q301 TKTC3198Y- TR KTC3198Y
Q402 TKTC3207— TR KTC3207 (TP)
Q403 TKTC3198Y- TR KTC3198Y
Q405 TKSC2330Y- TR KSC2330Y (TP)
Q502 TKTA1266Y- TR KTA1266Y (TP)
Q503 TKTA1266Y- TR KTA1266Y (TP)
Q504 TKTA1266Y- TR KTA1266Y (TP)
Q505 TKTC3198Y- TR KTC3198Y
Q506 TKTC3198Y- TR KTC3198Y
Q507 TKTA1266Y- TR KTA1266Y (TP)
Q508 TKTC3198Y- TR KTC3198Y
Q509 TKSC2330Y- TR KSC2330Y (TP)
Q510 TKTA1266Y- TR KTA1266Y (TP)
Q511 TKTC3198Y- TR KTC3198Y
Q581 TKTC3198Y- TR KTC3198Y
Q582 TKTC3198Y- TR KTC3198Y
Q583 TKTC3198Y- TR KTC3198Y

LOC PART CODE PART NAME DESCRIPTION REMARK

Q584 TKTC3198Y- TR KTC3198Y
Q585 TKTC3197— TR KTC3197 (TP)
Q586 TKTC3198Y- TR KTC3198Y
Q601 TKTC3198Y- TR KTC3198Y
Q602 TKTC3198Y- TR KTC3198Y
Q801 TKSA1013Y- TR KSA1013Y (TP)
QF01 TKTC3198Y- TR KTC3198Y
R302 RN02B471JS R METAL FILM 2W 470 OHM J SMALL
R303 RN02B129JS R METAL FILM 2W 1.2 OHM J SMALL
R304 RN01B221JS R METAL FILM 1W 220 OHM J SMALL
R305 RN02B331JS R METAL FILM 2W 330 OHM J SMALL
R312 RN02B681JS R METAL FILM 2W 680 OHM J SMALL
R407 RN02B102JS R METAL FILM 2W 1K OHM J SMALL
R422 RN02B159JS R METAL FILM 2W 1.5 OHM J SMALL
R423 RN02B360JS R METAL FILM 2W 36 OHM J SMALL
R820 RN02B150JS R METAL FILM 2W 15 OHM J SMALL
R821 RN02B150JS R METAL FILM 2W 15 OHM J SMALL
R830 RN02B101JS R METAL FILM 2W 100 OHM J SMALL
R922 RN02B100JS R METAL FILM 2W 10 OHM J SMALL
SW701 5S50101090 SW TACT THVH472GCA
SW702 5S50101090 SW TACT THVH472GCA
SW703 5S50101090 SW TACT THVH472GCA
SW704 5S50101090 SW TACT THVH472GCA
SW705 5S50101090 SW TACT THVH472GCA
SW706 5S50101090 SW TACT THVH472GCA
ZZ200 PTMPJAD691 PCB MAIN AXIAL AS DTC-21D9ME
10 2TM14006LB TAPE MASKING 3M #232 6.0X2000M
20 2TM10006LB TAPE MASKING 3M #232-MAP-C 6.2X2000M
A001 4859806893 PCB MAIN 330X246
C102 CBZP1C103M C CERA SEMI 16V Y5S 0.01MF M (AXIAL)
C312 CCZB1H104K C CERA HIBK 50V 0.1MF K AXL 52MM
C407 CCZB1H331K C CERA 50V B 330PF K (AXIAL)
C504 CCZF1H473Z C CERA 50V F 0.047MF Z
C515 CCZF1H223Z C CERA 50V F 0.022MF Z
C516 CCZF1H223Z C CERA 50V F 0.022MF Z
C517 CCZF1H223Z C CERA 50V F 0.022MF Z
C529 CCZB1H331K C CERA 50V B 330PF K (AXIAL)
C532 CCZB1H331K C CERA 50V B 330PF K (AXIAL)
C534 CCZF1H103Z C CERA 50V F 0.01MF Z
C538 CCZB1H221K C CERA 50V B 220PF K (AXIAL)
C539 CCZB1H221K C CERA 50V B 220PF K (AXIAL)
C540 CCZB1H221K C CERA 50V B 220PF K (AXIAL)
C546 CBZF1H104Z C CERA SEMI 50V F 0.1MF Z
C552 CCZF1H103Z C CERA 50V F 0.01MF Z
C601 CBZF1H104Z C CERA SEMI 50V F 0.1MF Z
C602 CBZF1H104Z C CERA SEMI 50V F 0.1MF Z
C603 CCZB1H104K C CERA HIBK 50V 0.1MF K AXL 52MM
C604 CBZF1H104Z C CERA SEMI 50V F 0.1MF Z
C607 CCZB1H104K C CERA HIBK 50V 0.1MF K AXL 52MM
C608 CBZF1H104Z C CERA SEMI 50V F 0.1MF Z
C609 CBZF1H104Z C CERA SEMI 50V F 0.1MF Z
C610 CBZF1H104Z C CERA SEMI 50V F 0.1MF Z
C613 CBZF1H104Z C CERA SEMI 50V F 0.1MF Z
C614 CBZF1H104Z C CERA SEMI 50V F 0.1MF Z
C616 CBZF1H104Z C CERA SEMI 50V F 0.1MF Z
C622 CBZF1H104Z C CERA SEMI 50V F 0.1MF Z
C623 CBZF1H104Z C CERA SEMI 50V F 0.1MF Z
C630 CBZF1H104Z C CERA SEMI 50V F 0.1MF Z
C632 CBZF1H104Z C CERA SEMI 50V F 0.1MF Z
C633 CBZF1H104Z C CERA SEMI 50V F 0.1MF Z
C634 CBZF1H104Z C CERA SEMI 50V F 0.1MF Z

-16-

ELECTRICAL PARTS LIST

LOC PART CODE PART NAME DESCRIPTION REMARK

C635 CBZF1H104Z C CERA SEMI 50V F 0.1MF Z
C832 CBZF1H104Z C CERA SEMI 50V F 0.1MF Z
C901 CCZB1H471K C CERA 50V B 470PF K (AXIAL)
C902 CCZB1H471K C CERA 50V B 470PF K (AXIAL)
C903 CCZB1H471K C CERA 50V B 470PF K (AXIAL)
CD01 CCZF1H103Z C CERA 50V F 0.01MF Z
D101 DUZ33B—— DIODE ZENER UZ-33B
D102 DUZ5R6BM— DIODE ZENER UZ-5.6BM
D301 D1N4004S— DIODE 1N4004S
D311 DUZ33B—— DIODE ZENER UZ-33B
D312 DUZ33B—— DIODE ZENER UZ-33B
D401 D1N4937G— DIODE 1N4937G (TAPPING)
D405 DUZ9R1BM— DIODE ZENER UZ-9.1BM
D406 DRGP15J—- DIODE RGP15J
D407 D1N4937G— DIODE 1N4937G (TAPPING)
D410 D1N4937G— DIODE 1N4937G (TAPPING)
D411 DUZ12BM—- DIODE ZENER UZ-12BM (UNIZON)
D412 D1N4148—- DIODE 1N4148 (TAPPING)
D501 D1N4148—- DIODE 1N4148 (TAPPING)
D502 D1N4148—- DIODE 1N4148 (TAPPING)
D503 DUZ5R1B—- DIODE ZENER UZ-5.1B
D504 DUZ5R1B—- DIODE ZENER UZ-5.1B
D505 DUZ5R1B—- DIODE ZENER UZ-5.1B
D506 D1N4148—- DIODE 1N4148 (TAPPING)
D507 D1N4148—- DIODE 1N4148 (TAPPING)
D508 D1N4148—- DIODE 1N4148 (TAPPING)
D510 DUZ2R7B—- DIODE ZENER UZ-2.7B
D511 D1N4148—- DIODE 1N4148 (TAPPING)
D512 D1N4148—- DIODE 1N4148 (TAPPING)
D513 D1N4148—- DIODE 1N4148 (TAPPING)
D514 D1N4148—- DIODE 1N4148 (TAPPING)
D581 DUZ5R6BM— DIODE ZENER UZ-5.6BM
D582 DUZ5R6BM— DIODE ZENER UZ-5.6BM
D583 DUZ5R6BM— DIODE ZENER UZ-5.6BM
D589 DUZ5R1B—- DIODE ZENER UZ-5.1B
D592 DUZ5R1B—- DIODE ZENER UZ-5.1B
D593 DUZ5R1B—- DIODE ZENER UZ-5.1B
D594 DUZ5R1B—- DIODE ZENER UZ-5.1B
D601 D1N4148—- DIODE 1N4148 (TAPPING)
D602 D1N4148—- DIODE 1N4148 (TAPPING)
D802 DLT2A05G— DIODE LT2A05G (TP)
D803 DLT2A05G— DIODE LT2A05G (TP)
D804 DLT2A05G— DIODE LT2A05G (TP)
D805 DLT2A05G— DIODE LT2A05G (TP)
D806 D1N4937G— DIODE 1N4937G (TAPPING)
D807 D1N4937G— DIODE 1N4937G (TAPPING)
D808 D1N4937G— DIODE 1N4937G (TAPPING)
D809 D1N4937G— DIODE 1N4937G (TAPPING)
D811 DUZ3R3B—- DIODE ZENER UZ-3.3B
D813 D1N4937G— DIODE 1N4937G (TAPPING)
D816 DRGP15J—- DIODE RGP15J
D902 D1N4937G— DIODE 1N4937G (TAPPING)
DD01 DUZ5R1B—- DIODE ZENER UZ-5.1B
DF01 DUZ5R1B—- DIODE ZENER UZ-5.1B
DF02 DUZ5R1B—- DIODE ZENER UZ-5.1B
J001 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J002 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J003 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J004 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J006 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J007 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING

LOC PART CODE PART NAME DESCRIPTION REMARK

J008 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J009 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J010 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J011 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J012 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J013 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J014 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J015 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J016 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J017 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J018 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J019 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J020 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J021 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J022 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J023 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J025 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J026 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J027 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J028 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J029 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J030 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J031 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J032 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J033 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J034 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J035 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J036 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J037 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J038 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J039 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J040 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J041 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J042 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J043 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J044 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J045 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J046 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J047 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J048 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J049 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J050 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J051 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J052 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J053 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J054 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J055 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J056 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J057 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J058 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J059 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J060 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J061 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J062 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J063 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J064 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J065 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J066 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J067 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J068 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING
J069 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING