Welcome to the installation guide for the KeylessGo portion of the remote start for Mercedes. Please
thoroughly review this manual before installation as there are details that are essential to operation of
the vehicle.
This manual is intended for experienced installers. Firstech recommends professional installation as
we are not responsible for improper use and/or installation. For questions please call 888-820-3690
Monday through Friday 8 am to 5 pm PST.
Mercedes Benz vehicles that have a push button for starting will require the KeylessGo harness. (Part
number: FT-MBKG20-HRN) This will let the user lock and unlock their vehicle from DroneMobile, 2
or 1 Way remote or factory key fob during remote start. This harness must be ran to the KeylessGo
module to a separate CAN connector in the vehicle. The other end of the harness plugs into the 2
pin KeylessGo port on the DC for Mercedes control module.
Note: You must install the DC control module and DroneMobile or RF kit before connecting the
KeylessGo harness. Also don’t forget to test functionality of the remote start.
Instructions
1. Locate the CAN distribution block that houses the KeylessGo connector. (See table below)
2. Unplug all connectors from the block that contain brown and brown/red twisted CAN wires.
3. Locate the KeylessGo module. (See table below)
4. Unplug the KeylessGo module.
5. Unclip and remove the connector cover from the KeylessGo connector.
6. Locate the twisted brown and brown/red CAN wires in the plug.
9. Plug all the other connectors back into the CAN block except for the KeylessGo connector that you
located in step 8.
10. Using a pick tool or small flat blade, open the retaining clip that holds the connecting terminals
on the side of the connector housing.
11. Using a pick tool or small flat blade release the tabs on each pin and remove them from the
connector housing. The release tab will need to be pressed down two separate times to remove it
from the connector housing.
Copyright 2011 Firstech, LLC. | 1
Page 2
Data Controller (DC)
Remote Start for Mercedes
www.compustar.com
888.820.3690
KeylessGo
FT-MBKG20-HRN Installation Guide
12. Close the retaining clip and put the empty connector housing back into the CAN block. (See
images below)
13. Insert the pins into the provided plug housing making sure the polarity is correct with the
extension harness coming from the DC control module.
Brown/Red--->Brown/Red•
Brown--->Brown•
14. Close the retaining clip on the new connector.
15. Plug the connector into the harness from the DC control module.
Please see the step by step images below for details on the KeylessGo connection:
Module Location Table
ClassYearCAN BlockKeylessGo Module
C2008-2011
CL, S2007-2010
CL, S2011
CLS2012
E coupe/sedan2010-2011
E convertible2010-2011
Passenger front door jamb
in wire trough
Under rear of driver’s front
seat
Under rear of driver’s front
seat
Passenger front door jamb
in wire trough
Passenger front door jamb
in wire trough
Passenger front door jamb
in wire trough
Right side of trunk near tail
light
Right side of trunk near tail
light
Left side of trunk behind
metal bracket
Right side of trunk near tail
light
Right side of trunk near tail
light
In trunk behind rear seat
back (remove carpet trim)
E wagon2011
GL2006-2011
GLK2010-2011
ML*2006-2011Passenger front kick panel*
R*2006-2010Passenger front kick panel*Below spare tire in cargo*
R*2011Passenger front kick panel*
*ML and R class do not require to change connector plug (steps 10-14 not required). Just plug
into the extension harness once the correct connector is found in the block.
Passenger front door jamb
in wire trough
Right side compartment in
cargo area
Passenger front door jamb
in wire trough
Right side of cargo area
behind bracket
Right side compartment in
cargo area
Center of cargo floor under
carpet
Right side compartment in
cargo area*
Under false floor behind
driver’s seat*
Copyright 2011 Firstech, LLC. | 2
Page 3
Data Controller (DC)
Remote Start for Mercedes
KeylessGo
KeylessGo Component Locations
C and E Class module locations.
KeylessGo plug
on module in
trunk
FT-MBKG20-HRN Installation Guide
C, E and GLK Class
www.compustar.com
888.820.3690
KeylessGo Module
Plug removed - faces body of car
E Coupe KeylessGo module -- right rear of trunkC and E Sedan KeylessGo module -- right rear trunk
KeylessGo module behind bracket
CAN connector, 2010 and up E, C, GLK class and
E Wagon -- right rear cargo area
2012 CLS passenger front door under plastic wire
moulding
Copyright 2011 Firstech, LLC. | 3
Page 4
Data Controller (DC)
Remote Start for Mercedes
KeylessGo
CL and S Class module locations.
CL and S Class
www.compustar.com
888.820.3690
FT-MBKG20-HRN Installation Guide
KeylessGo Module
Right rear corner of trunkUnder rear of driver’s seat
2011 CL and S -- Left side trunk, remove metal
bracket
CAN Connector
KeylessGo Module
GLK -- Under cargo floor behind seat
Copyright 2011 Firstech, LLC. | 4
Page 5
Data Controller (DC)
Remote Start for Mercedes
KeylessGo
GL, ML, and R Class module locations.
KeylessGo Module
CAN Connector
FT-MBKG20-HRN Installation Guide
GL, ML, and R Class
www.compustar.com
888.820.3690
GL -- right rear side of cargo compartmentR KeylessGo module -- under cargo area floor
ML KeylessGo -- right rear side of cargo
compartment
ML and R CAN distribution block, front passenger
kick panel
Copyright 2011 Firstech, LLC. | 5
Page 6
Data Controller (DC)
Remote Start for Mercedes
KeylessGo
FT-MBKG20-HRN Installation Guide
GL, ML, and R Class
www.compustar.com
888.820.3690
2011 R -- under floor behind driver’s seat
KeylessGo Component Locations
Pin Removal and Reinstall
CAN plug removedRelease retaining clip
Copyright 2011 Firstech, LLC. | 6
Page 7
Data Controller (DC)
Remote Start for Mercedes
KeylessGo
FT-MBKG20-HRN Installation Guide
Pin Removal and Reinstall
www.compustar.com
888.820.3690
Remove pins from connector housingPins removed, connector housing empty
Empty connector housing reinstalledPins ready for new connector housing
Copyright 2011 Firstech, LLC. | 7
Page 8
Data Controller (DC)
Remote Start for Mercedes
KeylessGo
FT-MBKG20-HRN Installation Guide
Pin Removal and Reinstall
Brown Matches Brown
Brown/Red Matches Brown/Red
www.compustar.com
888.820.3690
Pins installed in connector housingPlugs matched up and completed
KeylessGo Finder (V27.4 and up)
Beginning with V27.4 (see serial number sticker on the rear of the unit), there is an on board KeylessGo
finder. This will make finding the correct plug for connecting to the KeylessGo system on vehicles that require
it much easier. Basic install of the Mercedes DC must be completed prior to testing for KeylessGo (this guide
assumes the starter module is installed and properly working).
Instructions
1. Locate the specified CAN distribution block where the KeylessGo connection should be made.
2. Turn the key to accessory (one click clockwise from the off position). If there is a push button in the ignition
cylinder, it can be removed so the key can be inserted in its place. Grasp the button and pull it out of the
ignition switch.
3. Look inside the Mercedes DC module through the end plate opposite the main wiring plug. You should
see red LEDs that are lit up. One of those should be flashing at a slow pace.
4. In the CAN distribution block, begin to remove connectors one at a time. Each connector should be
unplugged for 15-20 seconds each. Observe the flashing light as you do this. You should end up with two
connectors that cause the flashing light to stop flashing and stay solid on or solid off.
5. Isolate those two connectors to one end of the distribution block and leave the rest alone.
6. Turn the key to the off position and remove it.
7. Take the two connectors from step 5 and remove one at a time. Once one is removed, use the keyfob to
unlock the doors. Removing one of those connectors will cause the door locks to stop working from the
keyfob and one won’t.
8. Take the connector that caused the door locks to stop working and plug it back in.
9. Connect the KeylessGo harness to the plug from step 7 where the door locks continued to work.
Copyright 2011 Firstech, LLC. | 8
Page 9
Data Controller (DC)
Remote Start for Mercedes
www.compustar.com
888.820.3690
KeylessGo
FT-MBKG20-HRN Installation Guide
That completes the KeylessGo portion of your installation. Please see the vehicle specific installation guide
for more information.
Firstech, LLC. is not responsible for any damages whatsoever, including but not limited to any consequential
damages, incidental damages, damages for loss of time, loss of earnings, commercial loss, loss of economic
opportunity and the like that may or may not have resulted from the installation or operation of the Data
Controller for Mercedes.
Copyright 2011 Firstech, LLC. | 9
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.