ComPro CS-200 Alarm Sounder Technical data
CS-200 Alarm Sounder
CABLE PREPARATION
32 Alarm tones
Volume control
Clip fit base
12V or 24V operation
SPE
CIFICATI
ON
Operating voltage
Start up current
Current consumption (nom)
Monitoring mode
Wire termination
Temperature range
Case material
Compliance
Environmental protection
DIMENSIONS
96
Ο
63
18~28V DC (9~18V DC non Fire use)
30mA for 2ms
See table overleaf
Polarised Diode
0.28mm² ~ 2.5mm² wire conductors
-10
º
C to +55ºC
ABS Flame retardant (V0)
EN54-3 Fire alarm device - Sounder
IP21C Type A *
* Product meet minimum
requirements of IP21C in
accordance with EN54-3.
Base Fixing
Positions
Knock-outs
Knock-outs
A rear cable entry hole is provided.
For surface wiring remove knock-outs.
CONNECTION DETAILS
Tone Selection Switch
See table overleaf
1
= OPEN
0
=
CLOSED
-V
DC
-V
DC (2nd Tone)
+
V
(1st Tone)
DC
To next
sounder
Volume Control
T
urn clockwise to
increase
2nd tone
overrides 1st tone
INSTALLATION
5
0
Unlock
The sounder clips onto the base.
0
6
CE marking under the CPD was affixed on: See batch code on product.
Fulleon Ltd, Cwmbran, South Wales, UK.
www.fulleon.com
To remove the souber insert a small
tool into the base hole and pull apart.
0832-CPD-0523
25-8379 Iss A
1
2
1
14
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
(i)
Tones certified under the C
11111
14
11110
14
11101
14
11100
4
11011
4
11010
14
11001
14
11000
4
10111
14
10110
14
10101
4
10100
14
10011
14
10010
14
10001
16
10000
17
01111
18
01110
19
01101
20
01100
21
01011
14
01010
14
01001
4
01000
25
00111
26
00110
27
00101
10
00100
33
00011
35
00010
31
00001
32
00000
PD (Fire Alarm Applications) are shown in the column marked EN54-3
& 970
800
800 & 970
800 & 970
2850
Hz
2400
~ 2850
2400 ~ 2850
300 ~ 1200
1200 ~ 500
2400 & 2850
970
Hz
800 & 970
2850
Hz
970
Hz
970
Hz
554 & 440
660
Hz
660
Hz
660
Hz
660
Hz
554 & 440
660
Hz
2850
Hz
800 ~ 970
2400 ~ 2850
970
Hz
800 ~ 970
800 ~ 970
800 & 970
990 & 650
510 & 610
300 ~ 1200
4000
Hz
Hz
2Hz (250ms~250
Hz
7Hz (7/
Hz
1Hz (1/
Stead
Hz
7
Hz
Hz
1
Hz
Hz
3s Sweep, 0.5s
Hz
Hz
1
Hz
2Hz (250ms~250
0.5Hz (1s On / 1s Off
Hz
1Hz (500ms~500
0.5Hz (1s On / 1s Off
0.8Hz (250ms On / 1s Off
Stead
Hz
100ms ~ 400
3.3Hz (150ms On / 150ms Off
0.28Hz (1.8s On / 1.8s Off
0.05Hz (13s Off / 6.5Hz On
Stead
Hz
0.5Hz (1s On / 1s Off
1Hz (500ms ~ 500
4Hz (150ms On / 100ms Off
Hz
50
Hz
Hz
50
Hz
3 x 500ms pulses followed by 1.5s
3
Hz
x
Hz
Hz
Hz
Hz
500ms pulses followed by 1.5s
3 x 500ms pulsed two tone followed by 1.5s
Hz (
250ms ~ 250
2
2Hz (250ms ~ 250
2Hz (250ms ~ 250
Hz
Hz
1
Stead
ms)
s)
s)
y
silenc
e, then repeat
ms)
)
ms)
)
y
ms
y
y
)
ms)
ms)
ms) (Sym
ms) (
)
)
)
)
)
phoni Tone
Squashni
(ii) All other SPL measurements are taken ‘on axis’ & are not third party verified.
(iii) Detailed EN54-3 polar SPL measurements are available in M06-009
silenc
silenc
Micro T
s)
e
e
ones)
silenc
e
BS
Fire T
BS
Fire T
BS
Fire T
Dutch Fire T
DIN T
Fire T
BS
BS
Fire T
French Fire T
wedish Fire T
S
S
wedish Fire T
S
wedish Fire T
wedish Fire T
S
S
wedish Fire T
S
wedish Fire T
lic
an Cro
Pe
BS
Fire T
O
8201
IS
ISO 8201
IS
O
8201
BS
Fire T
Fire T
BS
BS
Fire T
one
one
one
one
one
one
one
one
one
one
one
ssi
one
one
one
one
one
one
one
ng
@
20
mAdB(A)
101
13
102
13
103
13
107
33
111
33
112
33
103
14
15
102
33
107
101
11
101
13
107
24
100
6
100
14
102
14
100
7
101
19
101
10
101
11
102
14
101
18
105
24
101
13
110
33
100
9
103
14
100
9
101
13
103
21
100
17
103
15
101
17
c
EN54-3
Min SPL
@ 28Vdc
@ Max Volume
@ Loudest node
dB(A)
*
*
95
*
*
*
97
94
*
*
*
*
*
95
*
*
*
*
*
*
*
*
*
*
*
*
*
*
96
92
*
*
25
-8379 Iss
A
Loading...