Citizen E210 Abbreviated Instruction
English
CHARGE
CHARGE
CHARGE
CHARGE
E210 Abbreviated instruction
• This watch is solar-powered. Expose the dial to light and use it sufficiently charged.
• To see details of charging time, specifications and operations, refer to the instruction manual:
E210 instruction manual
Component identification
• Models with the crown at the 3 o'clock position
Chronograph second
Button
Chronograph hour hand
• Models with the crown at the 12 o'clock position
Chronograph second
indication hand
Chronograph hour
Button C (recessed
• Actual appearance may differ from the illustrations.
• The crown has two positions when pulling it out.
• Refer also to our web page for detail of usage of the
scale and bezel on the watch.
(
http://www.citizenwatch-global.com/support/pdf/
enhanced/e.pdf
hand
Hour hand
C
(recessed
button)
Alarm hand
Alarm crown
Second hand
hand
Hour hand
Power reserve
hand
button)
Button
)
60
T
A
C
H
Y
M
E
T
45 15
7
130
60
140
E
R
150
65
70
CHARGE
12
75
9
80
85
90
3
ON
OFF
95
100
110
120
Crown
A
500
400
160
Power reserve indication
hand
Minute hand
Button
Chronograph minute
300
hand
250
Crown
220
200
Alarm indicator hand
180
Button
Date indication
B
Button
Chronograph minute
hand
Date indication
Minute hand
Second hand
Alarm hand
Alarm indicator hand
Alarm crown
A
B
Crown's position
0 1 2
Checking the power reserve
You can see current power reserve level by referring to the power reserve
indication hand. Use the watch with sufficiently charged.
Level
3 2 1 CHARGE
Indication
(Models with the
crown at the 3
o'clock position)
Indication
(Models with the
crown at the 12
o'clock position)
Duration (approx.)
Meaning
8 ‒ 7 months 7 ‒ 5 months
Power reserve is
sufficient.
Power reserve is
OK.
5 months ‒ 7
days
Power reserve is
get ting low.
OK for normal use. Charge immediately.
7 days or
shorter
Insufficient
charge warning
has started.
Setting the time
Pull the crown out to position 2 when the second hand points
1.
0 second.
The second hand stops.
Rotate the crown to set the time.
2.
• Change of date indication shows it just became AM. Take care the time set
is AM or PM.
• Move the hands 4 or 5 minutes forward and move them back to the right
time to set the time more precisely.
Push the crown in to position 0 in accordance with a reliable
3.
time source to finish the procedure.
The second hand starts moving.
Setting the date indication
• Do not adjust the date indication while the watch shows 9:00 PM ‒ 1:00 AM.
Otherwise, the date indication may change incorrectly thereafter.
• Date indication adjustment is required on the first days of March, May, July,
October and December.
Pull the crown out to position 1.
1.
Rotate the crown counterclockwise to set the date indication.
2.
Push the crown in to position 0 to finish the procedure.
3.
1/2
E210 Abbreviated instruction
Using the chronograph
• Measuring up to 12 hours in 1/5 second increments.
Push the crown in to position 0.
1.
Start measurement.
2.
Start/stop: press button A.
Reset: press button
• Be sure to reset chronograph after finishing measurement.
B
while the chronograph is stopped.
12 hours or more after starting measurement
As 12 hours have passed since measurement started, the chronograph hands stop
but measurement has not stopped. Reset the chronograph.
Using the alarm
• The alarm time is set in 12-hour basis.
Pull out the alarm crown.
1.
Rotate the alarm crown to set the alarm time.
2.
• Move the alarm indicator hand 30 minutes or so forward and move it back
to the time you want to set.
• The alarm may sound earlier or later (about ±5 minutes) than the time set.
Use the time set by the hand only as approximate reference.
Push in the alarm crown.
3.
The alarm time setting is finished.
• Press the alarm crown to set the alarm hand to “ON” if it points “OFF”.
To stop alarm
Press the alarm crown.
• The alarm sounds for 20 seconds.
To set the alarm ON/OFF
Each time you press the alarm crown, ON/OFF of the alarm changes alternately.
• The alarm sounds if it is set to “ON” again within 20 minutes after stopping it.
Resetting the watch — All Reset
Confirm the following before All Reset.
• The power reserve indication hand points level 3 or 2.
• The chronograph has been reset.
Pull the crown out to position 2 when the second hand points
1.
0 second.
Press and release both button B and recessed button C at the
2.
same time.
Alarm sounds and the power reserve indication hand move to level 3.
The reference position of each hand is adjusted automatically.
Push the crown in to position 0 to finish the procedure.
3.
The power reserve indication hand moves back and forward and the second
hand starts moving.
After All Reset
After All Reset, set the time and date indication. Set also the alarm.
2/2
Loading...