Cisco Catalyst DFC3A, Catalyst DFC3B, Catalyst DFC3BXL, WS-F6K-DFC=, WS-F6K-DFC3A= Installation Note
...Page 1
Catalyst 6500 Series DFC, DFC3A, DFC3B, and
DFC3BXL Installation Note
Product numbers:
WS-F6K-DFC(=)
WS-F6K-DFC3A(=)
WS-F6K-DFC3B(=)
WS-F6K-DFC3BXL(=)
Note Throughout this publication, unless otherwise noted, the term DFC refers to the DFC, DFC3A, DFC3B,
and DFC3BXL.
This publication describes how to install the Catalyst 6500 series Distributed Forwarding Card (DFC)
on Catalyst 6500 series fabric-enabled modules.
Note You can only install the DFC on fabric-enabled modules. See the “Hardware and Software
Requirements” section on page 2 for more information.
Contents
This publication contains these sections:
• Hardware and Software Requirements, page 2
• Safety Overview, page 3
• Parts List, page 7
• Required Tools, page 8
• Installation Guidelines, page 8
Corporate Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Copyright © 2001–2005 Cisco Systems, Inc. All rights reserved.
Page 2
Hardware and Software Requirements
• Removing the DFC, page 9
• Installing the DFC, page 12
• Related Documentation, page 19
• Obtaining Documentation, page 19
Hardware and Software Requirements
The requirements for using the DFC or DFC3A are as follows:
• DFC Hardware and Software Requirements, page 2
• DFC3A, DFC3B, DFC3BXL Hardware and Software Requirements, page 3
DFC Hardware and Software Requirements
To install and use the DFC, you need the following:
• Catalyst 6500 series switch (Catalyst 6506, 6509, 6509-NEB, or 6513) or Cisco 7600 series router
(Cisco 7606, 7609, or 7613)
• Supervisor Engine 2 with Multilayer Switch Feature Card 2 (MSFC2) running Cisco IOS software
on the Supervisor Engine 2 and MSFC2
Note You cannot have a DFC in a system with a Supervisor Engine 720.
• Fabric-enabled module
• Switch Fabric Module (SFM) (WS-C6500-SFM) or SFM 2 (WS-X6500-SFM2)
Note The SFM must be installed in slot 5 or slot 6 of the 6-slot or the 9-slot chassis. The SFM
cannot be installed in the 3-slot or 13-slot chassis.
Note The SFM 2 must be installed in slot 5 or slot 6 of the 6-slot or the 9-slot chassis or in slot 7
or slot 8 of the 13-slot chassis.
Catalyst 6500 Series DFC, DFC3A, DFC3B, and DFC3BXL Installation Note
2
78-11627-04
Page 3
DFC3A, DFC3B, DFC3BXL Hardware and Software Requirements
To install and use the DFC3A, DFC3B, or DFC3BXL, you need the following:
• Catalyst 6500 series switch (Catalyst 6503, 6506, 6509, 6509-NEB, or 6513) or Cisco 7600 series
router (Cisco 7603, 7606, 7609, or 7613)
• Supervisor Engine 720 with MSFC3 running Cisco IOS software on the Supervisor Engine 720 and
MSFC3
Note You cannot have a DFC3A, DFC3B, or DFC3BXL in a system with a Supervisor Engine 2.
• Fabric-enabled module
Note Supervisor Engine 720 supports a DFC3A, DFC3B, or DFC3BXL on these WS-X6516-GBIC hardware
revisions:
• Lower than 5.0
• 5.4 and higher
Supervisor Engine 720 does not support a DFC3A, DFC3B, or DFC3BXL on WS-X6516-GBIC
hardware revisions 5.0 through 5.3. With a Supervisor Engine 720 and with a DFC3A, DFC3B, or
DFC3BXL installed, WS-X6516-GBIC hardware revisions 5.0 through 5.3 do not power up.
Without a DFC3A, DFC3B, or DFC3BXL, WS-X6516-GBIC hardware revisions 5.0 through 5.3 operate
in bus mode.
Safety Overview
Safety Overview
Safety warnings appear throughout this publication in procedures that, if performed incorrectly, may
harm you. A warning symbol precedes each warning statement.
78-11627-04
Catalyst 6500 Series DFC, DFC3A, DFC3B, and DFC3BXL Installation Note
3
Page 4
Safety Overview
Warning
Waarschuwing
IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar
with standard practices for preventing accidents. To see translations of the warnings that appear in
this publication, refer to the translated safety warnings that accompanied this device.
Note: SAVE THESE INSTRUCTIONS
Note: This documentation is to be used in conjunction with the specific product installation guide
that shipped with the product. Please refer to the Installation Guide, Configuration Guide, or other
enclosed additional documentation for further details.
BELANGRIJKE VEILIGHEIDSINSTRUCTIES
Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan
veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij
elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard
praktijken om ongelukken te voorkomen. Voor een vertaling van de waarschuwingen die in deze
publicatie verschijnen, dient u de vertaalde veiligheidswaarschuwingen te raadplegen die bij dit
apparaat worden geleverd.
Opmerking BEWAAR DEZE INSTRUCTIES.
Opmerking Deze documentatie dient gebruikt te worden in combinatie met de
installatiehandleiding voor het specifieke product die bij het product wordt geleverd. Raadpleeg de
installatiehandleiding, configuratiehandleiding of andere verdere ingesloten documentatie voor
meer informatie.
Varoitus
TÄRKEITÄ TURVALLISUUTEEN LIITTYVIÄ OHJEITA
Tämä varoitusmerkki merkitsee vaaraa. Olet tilanteessa, joka voi johtaa ruumiinvammaan. Ennen
kuin työskentelet minkään laitteiston parissa, ota selvää sähkökytkentöihin liittyvistä vaaroista ja
tavanomaisista onnettomuuksien ehkäisykeinoista. Tässä asiakirjassa esitettyjen varoitusten
käännökset löydät laitteen mukana toimitetuista ohjeista.
Huomautus SÄILYTÄ NÄMÄ OHJEET
Huomautus Tämä asiakirja on tarkoitettu käytettäväksi yhdessä tuotteen mukana tulleen
asennusoppaan kanssa. Katso lisätietoja asennusoppaasta, kokoonpano-oppaasta ja muista
mukana toimitetuista asiakirjoista.
Catalyst 6500 Series DFC, DFC3A, DFC3B, and DFC3BXL Installation Note
4
78-11627-04
Page 5
Safety Overview
Attention
Warnung
IMPORTANTES INFORMATIONS DE SÉCURITÉ
Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant causer
des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez conscient
des dangers posés par les circuits électriques et familiarisez-vous avec les procédures couramment
utilisées pour éviter les accidents. Pour prendre connaissance des traductions d'avertissements
figurant dans cette publication, consultez les consignes de sécurité traduites qui accompagnent cet
appareil.
Remarque CONSERVEZ CES INFORMATIONS
Remarque Cette documentation doit être utilisée avec le guide spécifique d'installation du produit
qui accompagne ce dernier. Veuillez vous reporter au Guide d'installation, au Guide de
configuration, ou à toute autre documentation jointe pour de plus amples renseignements.
WICHTIGE SICHERHEITSANWEISUNGEN
Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu einer
Körperverletzung führen könnte. Bevor Sie mit der Arbeit an irgendeinem Gerät beginnen, seien Sie
sich der mit elektrischen Stromkreisen verbundenen Gefahren und der Standardpraktiken zur
Vermeidung von Unfällen bewusst. Übersetzungen der in dieser Veröffentlichung enthaltenen
Warnhinweise sind im Lieferumfang des Geräts enthalten.
Hinweis BEWAHREN SIE DIESE SICHERHEITSANWEISUNGEN AUF
Hinweis Dieses Handbuch ist zum Gebrauch in Verbindung mit dem Installationshandbuch für Ihr
Gerät bestimmt, das dem Gerät beiliegt. Entnehmen Sie bitte alle weiteren Informationen dem
Handbuch (Installations- oder Konfigurationshandbuch o. Ä.) für Ihr spezifisches Gerät.
Figyelem!
Avvertenza
FONTOS BIZTONSÁGI ELÕÍRÁSOK
Ez a figyelmezetõ jel veszélyre utal. Sérülésveszélyt rejtõ helyzetben van. Mielõtt bármely
berendezésen munkát végezte, legyen figyelemmel az elektromos áramkörök okozta kockázatokra,
és ismerkedjen meg a szokásos balesetvédelmi eljárásokkal. A kiadványban szereplõ
figyelmeztetések fordítása a készülékhez mellékelt biztonsági figyelmeztetések között található.
Megjegyzés ÕRIZZE MEG EZEKET AZ UTASÍTÁSOKAT!
Megjegyzés Ezt a dokumentációt a készülékhez mellékelt üzembe helyezési útmutatóval együtt kell
használni. További tudnivalók a mellékelt Üzembe helyezési útmutatóban (Installation Guide),
Konfigurációs útmutatóban (Configuration Guide) vagy más dokumentumban találhatók.
IMPORTANTI ISTRUZIONI SULLA SICUREZZA
Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle
persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli
relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti. Per le
traduzioni delle avvertenze riportate in questo documento, vedere le avvertenze di sicurezza che
accompagnano questo dispositivo.
Nota CONSERVARE QUESTE ISTRUZIONI
Nota La presente documentazione va usata congiuntamente alla guida di installazione specifica
spedita con il prodotto. Per maggiori informazioni, consultare la Guida all'installazione, la Guida
alla configurazione o altra documentazione acclusa.
78-11627-04
Catalyst 6500 Series DFC, DFC3A, DFC3B, and DFC3BXL Installation Note
5
Page 6
Safety Overview
Advarsel
Aviso
VIKTIGE SIKKERHETSINSTRUKSJONER
Dette varselssymbolet betyr fare. Du befinner deg i en situasjon som kan forårsake personskade.
Før du utfører arbeid med utstyret, bør du være oppmerksom på farene som er forbundet med
elektriske kretssystemer, og du bør være kjent med vanlig praksis for å unngå ulykker. For å se
oversettelser av advarslene i denne publikasjonen, se de oversatte sikkerhetsvarslene som følger
med denne enheten.
Merk TA VARE PÅ DISSE INSTRUKSJONENE
Merk Denne dokumentasjonen skal brukes i forbindelse med den spesifikke
installasjonsveiledningen som fulgte med produktet. Vennligst se installasjonsveiledningen,
konfigureringsveiledningen eller annen vedlagt tilleggsdokumentasjon for detaljer.
INSTRUÇÕES IMPORTANTES DE SEGURANÇA
Este símbolo de aviso significa perigo. O utilizador encontra-se numa situação que poderá ser
causadora de lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha em
atenção os perigos envolvidos no manuseamento de circuitos eléctricos e familiarize-se com as
práticas habituais de prevenção de acidentes. Para ver traduções dos avisos incluídos nesta
publicação, consulte os avisos de segurança traduzidos que acompanham este dispositivo.
Nota GUARDE ESTAS INSTRUÇÕES
Nota Esta documentação destina-se a ser utilizada em conjunto com o manual de instalação
incluído com o produto específico. Consulte o manual de instalação, o manual de configuração ou
outra documentação adicional inclusa, para obter mais informações.
¡Advertencia!
Varning!
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular
cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los
procedimientos estándar de prevención de accidentes. Vea las traducciones de las advertencias
que acompañan a este dispositivo.
Nota GUARDE ESTAS INSTRUCCIONES
Nota Esta documentación está pensada para ser utilizada con la guía de instalación del producto
que lo acompaña. Si necesita más detalles, consulte la Guía de instalación, la Guía de
configuración o cualquier documentación adicional adjunta.
VIKTIGA SÄKERHETSANVISNINGAR
Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada.
Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och
känna till vanliga förfaranden för att förebygga olyckor. Se översättningarna av de
varningsmeddelanden som finns i denna publikation, och se de översatta säkerhetsvarningarna som
medföljer denna anordning.
OBS! SPARA DESSA ANVISNINGAR
OBS! Denna dokumentation ska användas i samband med den specifika
produktinstallationshandbok som medföljde produkten. Se installationshandboken,
konfigurationshandboken eller annan bifogad ytterligare dokumentation för närmare detaljer.
Catalyst 6500 Series DFC, DFC3A, DFC3B, and DFC3BXL Installation Note
6
78-11627-04
Page 7
Parts List
Warning
Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Parts List
These parts are in the DFC kit:
• One Catalyst 6500 series DFC, DFC3A, DFC3B, or DFC3BXL
• One disposable grounding wrist strap
• One bag of mounting screws
78-11627-04
Catalyst 6500 Series DFC, DFC3A, DFC3B, and DFC3BXL Installation Note
7
Page 8
Required Tools
Required Tools
These tools are required to install the Catalyst 6500 series DFC:
• Antistatic mat or foam pad to support the removed module
• Number 1 Phillips screwdriver for the screws and cap nuts that fasten the DFC to the module
• Your own ESD-prevention equipment or the disposable grounding wrist strap included with all
upgrade kits, field-replaceable units (FRUs), and spares
Whenever you handle a module, always use a wrist strap or other grounding device to prevent
electrostatic discharge (ESD).
Installation Guidelines
Follow these guidelines when installing a DFC:
• When installing the DFC in a system with a Supervisor Engine 720, observe the following
restrictions for DFC3/PFC3 mismatch:
PFC Version DFC Version Restrictions
PFC3A DFC3A No restrictions.
DFC3B The DFC3B functions as a DFC3A.
DFC3BXL The DFC3BXL functions as a DFC3A.
PFC3B DFC3A You must reset the system after installing a
DFC3A-equipped module.
The PFC3B functions as a PFC3A.
DFC3B No restrictions.
DFC3BXL The DFC3BXL functions as a DFC3B.
PFC3BXL DFC3A You must reset the system after installing a
DFC3A-equipped module.
The PFC3BXL functions as a PFC3A.
DFC3B You must reset the system after installing a
DFC3B-equipped module.
The PFC3BXL functions as a PFC3B.
DFC3BXL No restrictions.
• Observe the following cautions:
Caution During this procedure, wear grounding wrist straps to avoid ESD damage to the module. Do
not directly touch the backplane with your hand or any metal tool, or you could shock
yourself.
Catalyst 6500 Series DFC, DFC3A, DFC3B, and DFC3BXL Installation Note
8
78-11627-04
Page 9
Caution Use care not to damage the connectors on the module. If you damage a connector, it will be
necessary to return the module to Cisco for repair.
Caution Yo u must install screws in all available standoffs. The screws provide grounding between the
DFC3 and the module. Failure to install all screws will invalidate the safety approvals and
pose a risk of fire and electrical hazard.
Removing the DFC
Note Throughout this publication, unless otherwise noted, the term DFC refers to the DFC, DFC3A, DFC3B,
and DFC3BXL.
Removing the DFC
Note The figures in this procedure show the DFC. The procedure is the same for the DFC, DFC3A, DFC3B,
and DFC3BXL.
Caution During this procedure, wear grounding wrist straps to avoid ESD damage to the module. Do not directly
touch the backplane with your hand or any metal tool, or you could shock yourself.
To remove the DFC, perform these steps:
Step 1 Remove the module from the Catalyst 6500 series switch. (Refer to the Catalyst 6500 Series Switch
Module Installation and Verification Note for removal instructions.)
Step 2 Place the module on an antistatic mat or foam, with the front of the module facing toward you.
Step 3 Use a Phillips-head screwdriver to remove the securing screws and the two cap nuts from the DFC.
(See Figure 1.)
78-11627-04
Catalyst 6500 Series DFC, DFC3A, DFC3B, and DFC3BXL Installation Note
9
Page 10
Removing the DFC
Figure 1 DFC Securing Screws and Cap Nuts
Step 4
LINE
LINE
9
10
Cap nuts (2)
11
12
LINE
13
14
LINE
LINE
11
12
15
16
LINE
LINE
13
14
LINE
15
16
120912
WS-X5530
Screws (12)
1
S
TU
A
T
S
2
LINE
3
4
LINE
LINE
1
2
5
6
LINE
LINE
3
4
7
8
LINE
LINE
5
6
9
10
LINE
7
8
Grasp the module at the two locations shown in Figure 2 and gently move the DFC up and down to loosen
the board connectors.
Figure 2 Disconnecting the DFC from the Module
Lift here
WS-X5530
1
S
U
T
A
T
S
2
LINE
3
4
LINE
LINE
1
2
5
6
LINE
LINE
3
4
7
8
LINE
LINE
5
6
9
10
LINE
LINE
7
8
LINE
9
10
Move up
and down
11
12
LINE
13
14
LINE
LINE
11
12
15
16
LINE
LINE
13
14
LINE
15
16
120865
Catalyst 6500 Series DFC, DFC3A, DFC3B, and DFC3BXL Installation Note
10
78-11627-04
Page 11
Step 5 Disconnect the power connector as shown in Figure 3.
Figure 3 Disconnecting the Power Connector
Lift board here to
disconnect power
connector
Removing the DFC
Step 6
WS-X5530
1
S
U
T
A
T
S
2
LINE
3
4
LINE
LINE
1
2
5
6
LINE
LINE
3
4
7
8
LINE
LINE
5
6
9
10
LINE
LINE
7
8
11
12
LINE
LINE
9
10
13
14
LINE
LINE
11
12
15
16
LINE
LINE
13
14
LINE
15
16
120866
Gently lift the DFC with both hands simultaneously, and remove the DFC from the module as shown in
Figure 4.
Figure 4 Removing the DFC
WS-X5530
1
S
U
T
TA
S
2
LINE
3
4
LINE
LINE
1
2
5
6
LINE
LINE
3
4
7
8
LINE
LINE
5
6
9
10
LINE
LINE
7
8
11
12
LINE
LINE
9
10
13
14
LINE
LINE
11
12
15
16
LINE
LINE
13
14
LINE
15
16
120867
Step 7
Place the removed DFC on an antistatic mat or antistatic foam pad.
78-11627-04
Catalyst 6500 Series DFC, DFC3A, DFC3B, and DFC3BXL Installation Note
11
Page 12
Installing the DFC
Installing the DFC
Note Throughout this publication, unless otherwise noted, the term DFC refers to the DFC, DFC3A, DFC3B,
and DFC3BXL.
Note The figures in this procedure show the DFC. The procedure is the same for the DFC, DFC3A, DFC3B,
and DFC3BXL.
Caution During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly
touch the backplane with your hand or any metal tool, or you could shock yourself.
To install the DFC on a fabric-enabled module, follow these steps:
Step 1 Remove the module from the Catalyst 6500 series switch. (Refer to the Catalyst 6500 Series Module
Installation Guide for removal instructions.)
Step 2 Place the module on an antistatic mat or foam, with the front of the module facing toward you
(see Figure 6).
Step 3 Remove the DFC from its antistatic bag.
Step 4 Align the two mounting holes on the DFC (see Figure 5) with the two male standoffs on the module
(see Figure 6). Make sure that the remaining mounting holes on the DFC are aligned with the remaining
standoffs.
Note The DFC is designed to be installed on different modules; therefore, there may be more
mounting holes on the DFC than there are standoffs on the module. Not all mounting holes on
the DFC will be used in all installations. Visually verify that there are standoffs beneath the
mounting holes before installing the securing screws.
Catalyst 6500 Series DFC, DFC3A, DFC3B, and DFC3BXL Installation Note
12
78-11627-04
Page 13
Figure 5 Mounting Holes on the DFC
Align with the male standoffs
on the module
Figure 6 Male Standoff Locations on the Module
Installing the DFC
47084
Step 5
Male standoffs
WS-X5530
1
S
U
T
A
T
S
2
E
IN
L
1
3
4
E
E
IN
IN
L
L
2
3
5
6
E
E
IN
IN
L
L
4
5
7
8
E
E
IN
IN
L
L
6
7
9
10
E
E
IN
IN
L
L
8
9
11
12
E
E
IN
IN
L
L
10
11
13
14
E
E
IN
IN
L
L
12
13
15
16
E
IN
L
14
E
E
IN
IN
L
L
16
15
47083
Ensure that the connectors on the DFC are aligned with the connectors on the module. Figure 7 shows
the connectors on the underside of the DFC.
78-11627-04
Catalyst 6500 Series DFC, DFC3A, DFC3B, and DFC3BXL Installation Note
13
Page 14
Installing the DFC
Step 6 Apply pressure to the area shown in Figure 8 to seat the power connector.
Figure 7 Distributed Forwarding Card Connectors
Connectors
47085
Figure 8 Seating the Power Connector
Apply pressure
here
WS-X5530
1
S
U
T
A
T
S
2
E
IN
L
1
3
4
E
E
IN
IN
L
L
2
3
5
6
E
E
IN
IN
L
L
4
5
7
8
E
E
IN
IN
L
L
6
7
9
10
E
E
IN
IN
L
L
8
9
11
12
E
E
IN
IN
L
L
10
11
13
14
E
E
IN
IN
L
L
12
13
15
16
E
IN
L
14
E
E
IN
IN
L
L
16
15
52720
Caution The following step shows how to preseat the DFC on the module. Preseating the DFC allows you to
verify that the keys on the connectors are properly aligned. Fully seating the DFC when the connectors
are not aligned will damage the connectors on both the DFC and the module. If you damage a connector,
you will have to return the module to Cisco for repair. It is important that the DFC is preseated prior to
being fully seated.
Step 7 With your left hand, apply firm pressure at the location shown in Figure 9. While applying pressure with
your left hand, move the DFC up and down with your right hand, no more than half an inch in either
direction, to preseat the DFC on the module.
Catalyst 6500 Series DFC, DFC3A, DFC3B, and DFC3BXL Installation Note
14
78-11627-04
Page 15
Figure 9 Preseating the Connector
Installing the DFC
Apply pressure
here
Move up and down
with your other hand
WS-X5530
1
S
TU
A
T
S
2
LINE
3
4
LINE
LINE
1
2
5
6
LINE
LINE
3
4
7
8
LINE
LINE
5
6
9
10
LINE
LINE
7
8
11
12
LINE
LINE
9
10
13
14
LINE
LINE
11
12
15
16
LINE
LINE
13
14
LINE
15
16
52721
Step 8 Verify that the keys on the connector are aligned and that the gap between the key and the opposing
connector is no more than 1/16 inch (1.6 mm) before fully seating the module (see Figure 10):
• If the keys are not aligned, remove the DFC and repeat Step 4 through Step 7.
• If the keys are not seated far enough, repeat Step 7.
Figure 10 Connector Keys
Board connector
Unseated
Standoff threads
not completely
key
through board
Board connector
Fully
seated
Standoff threads
completely
key
through board
52722
Step 9
With the bottom of your hand, apply firm pressure to the location shown in Figure 11 to fully seat the
DFC on the module.
78-11627-04
Catalyst 6500 Series DFC, DFC3A, DFC3B, and DFC3BXL Installation Note
15
Page 16
Installing the DFC
Figure 11 Seating the Distributed Forwarding Card on the Module
Apply pressure
here
WS-X5530
1
S
U
T
A
T
S
2
E
IN
L
1
3
4
E
E
IN
IN
L
L
2
3
5
6
E
E
IN
IN
L
L
4
5
7
8
E
E
IN
IN
L
L
6
7
9
10
E
E
IN
IN
L
L
8
9
11
12
E
E
IN
IN
L
L
10
11
13
14
E
E
IN
IN
L
L
12
13
15
16
E
IN
L
14
E
E
IN
IN
L
L
16
15
48444
Note The DFC is fully seated when there is no gap between the connector keys, and the bottom of the
DFC is in contact with the tops of the standoffs (see Figure 10).
Caution Using the screws to seat the DFC could warp the card. Before you install and tighten the securing screws,
ensure that the DFC is fully seated by visually verifying that there is no gap between the male and female
keys on the connectors and that the bottom of the DFC is in contact with the tops of the standoffs
(see Figure 10).
Step 10 Use a Phillips-head screwdriver to install the two screws at the front of the DFC and the one screw at the
power connector in the order shown in Figure 12.
Note You should visually verify that there are standoffs beneath the mounting holes before installing the
securing screws.
Catalyst 6500 Series DFC, DFC3A, DFC3B, and DFC3BXL Installation Note
16
78-11627-04
Page 17
Figure 12 Installing the First Set of Screws
Installing the DFC
Step 11
3
Install these first
2
1
WS-X5530
1
S
U
T
A
T
S
2
E
IN
L
1
3
4
E
E
IN
IN
L
L
2
3
5
6
E
E
IN
IN
L
L
4
5
7
8
E
E
IN
IN
L
L
6
7
9
10
E
E
IN
IN
L
L
8
9
11
12
E
E
IN
IN
L
L
10
11
13
14
E
E
IN
IN
L
L
12
13
15
16
E
IN
L
14
E
E
IN
IN
L
L
16
15
52723
Use a Phillips-head screwdriver to install the two cap nuts and two screws that surround the connector
(see Figure 13).
Figure 13 Installing the Second Set of Screws and Cap Nuts
Install these next
6 7
WS-X5530
1
S
U
T
A
T
S
2
E
IN
L
1
3
4
E
E
IN
IN
L
L
2
3
5
6
E
E
IN
IN
L
L
4
5
7
8
E
E
IN
IN
L
L
6
7
9
10
E
IN
IN
L
L
8
12
E
E
IN
L
10
9
5
4
11
E
IN
L
11
13
14
E
E
IN
IN
L
L
12
13
15
16
E
IN
L
14
E
E
IN
IN
L
L
16
15
48443
78-11627-04
Catalyst 6500 Series DFC, DFC3A, DFC3B, and DFC3BXL Installation Note
17
Page 18
Installing the DFC
Step 12 Use a Phillips-head screwdriver to install the remaining screws (see Figure 14).
Caution Yo u must install screws in all available standoffs. The screws provide grounding between the DFC and
Note You should visually verify that there are standoffs beneath the mounting holes before installing the
the module. Failure to install all screws will invalidate the safety approvals and pose a risk of fire and
electrical hazard.
securing screws.
Figure 14 Installing the Remaining Screws
18
WS-X5530
1
S
U
T
A
T
S
2
E
IN
L
1
3
4
E
E
IN
IN
L
L
2
3
5
6
E
E
IN
IN
L
L
4
5
7
8
E
IN
L
6
E
E
IN
IN
L
L
8
7
Step 13 Install the module in the Catalyst 6500 series switch.
Refer to the Catalyst 6500 Series Module Installation Guide for installation instructions.
Step 14 Power up the switch.
If the switch comes online, the system acknowledges the module and the DFC. The switch brings the
module and DFC online.
Catalyst 6500 Series DFC, DFC3A, DFC3B, and DFC3BXL Installation Note
9
10
E
IN
L
9
11
12
E
E
IN
IN
L
L
10
11
13
14
E
E
IN
IN
L
L
12
13
15
16
E
IN
L
14
E
E
IN
IN
L
L
16
15
47082
78-11627-04
Page 19
Related Documentation
These documents are available for the Catalyst 6500 series switches:
• Regulatory Compliance and Safety Information for the Catalyst 6500 Series Switches
• Catalyst 6500 Series Switch Module Installation and Verification Note
• Catalyst 6500 Series Switch Installation Guide
• Catalyst 6500 Series Switch Module Guide
• Catalyst 6500 Series Switch Software Configuration Guide
• Catalyst 6500 Series Switch Command Reference
• Catalyst 6500 Series Switch Cisco IOS Software Configuration Guide
• Catalyst 6500 Series Switch Cisco IOS Command Reference
• Catalyst 6500 Series DFC Memory Upgrade Installation Note
Obtaining Documentation
Related Documentation
Obtaining Documentation and Submitting a Service Request
For information on obtaining documentation, submitting a service request, and gathering additional
information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and
revised Cisco technical documentation, at:
http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html
Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed
and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free
service and Cisco currently supports RSS Version 2.0.
78-11627-04
Catalyst 6500 Series DFC, DFC3A, DFC3B, and DFC3BXL Installation Note
19
Page 20
Obtaining Documentation and Submitting a Service Request
This document is to be used in conjunction with the documents listed in the “Related Documentation” section.
CCVP, the Cisco logo, and Welcome to the Human Network are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn is
a service mark of Cisco Systems, Inc.; and Access Registrar, Aironet, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, Cisco, the Cisco
Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity,
Enterprise/Solver, EtherChannel, EtherFast, EtherSwitch, Fast Step, Follow Me Browsing, FormShare, GigaDrive, HomeLink, Internet Quotient, IOS,
iPhone, IP/TV, iQ Expertise, the iQ logo, iQ Net Readiness Scorecard, iQuick Study, LightStream, Linksys, MeetingPlace, MGX, Networkers,
Networking Academy, Network Registrar, PIX, ProConnect, ScriptShare, SMARTnet, StackWise, The Fastest Way to Increase Your Internet Quotient,
and TransPath are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.
All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply a
partnership relationship between Cisco and any other company. (0711R)
Printed in the USA on recycled paper containing 10% postconsumer waste.
Catalyst 6500 Series DFC, DFC3A, DFC3B, and DFC3BXL Installation Note
20
78-11627-04
Loading...