Celestron 114EQ User Manual

0 (0)

Model # 31032

FIRSTSCOPE 76 3" NEWTONIAN EQUATORIAL TELESCOPE

Model # 31044

FIRSTSCOPE 114 EQ 4.5" NEWTONIAN

TELESCOPE

Model # 31041

FIRSTSCOPE 114 SHORT 4.5" NEWTONIAN

EQUATORIAL TELESCOPE

INSTRUCTION MANUAL

E q u a t o r i a l M o d e l

Figure 1

IDENTIFYING PARTS OF FIGURE 1

1.	Front Cell (open part of tube)	22.	Declination Knob
2.	Secondary Mirror (inside)	23.	Declination Setting Circle
3.	Star Pointer Finderscope	24.	Right Ascension Knob
4.	Star Pointer Adjustment Knob (Altitude)	25.	Right Ascension Setting Circle
5.	Star Pointer Bracket	26.	Front Lens Cover
6.	Star Pointer Adjustment Knob (Azimuth)	27.	Right Ascension Cable Holder
7.	Eyepiece	28.	Horizontal Adjustment Knob
8.	Eyepiece Adapter	29.	Counterweight Shaft
9.	Focusing Knob	30.	Counterweight
10.	Focusing Tube	31.	Right Ascension Cable
11.	Telescope Optical Tube	32.	Tripod Accessory Tray
12.	Telescope Tube Mounting Hardware	33.	Equatorial Mount
13.	Declination Cable Holder	34.	Tripod Mounting Hardware
14.	Primary Mirror Cell (inside)	35.	Tripod Leg Tips
15.	Collimation Adjustment Screws	36.	Counterweight Lock
16.	Polar Axis Knob	37.	Finderscope Bracket Mounting Screws
17.	Latitude Scale	38.	Tripod Head
18.	Declination Cable	39.	Safety Washer for Counterweight
19.	Collapsible Center Leg Brace	40.	Bolts for Tube Mount Bracket
20.	Tripod Legs	41.	Saddle Bracket
21.	Telescope Tube Mount Bracket

1. INTRODUCTION

Thank you for purchasing this Celestron Newtonian Telescope. This telescope is a precision scientific instrument. With it you will enjoy numerous objects in the sky—planets, nebulae, star clusters, galaxies and other astronomical objects.

This manual covers both the 76mm equatorial mount model and the 114mm models. The equatorial mount contains setting circles and slow motion cables to make it easier to locate and track astronomical objects.

But, before your journey begins take time to read this manual to familiarize yourself with the operation and parts of your telescope.

WARNING—NEVER LOOK AT THE SUN WITH YOUR TELESCOPE OR ITS FINDERSCOPE. PERMANENT AND IRREVERSIBLE EYE DAMAGE MAY RESULT AS WELL AS DAMAGE TO YOUR TELESCOPE. HOWEVER, YOU MAY ENJOY LOOKING AT THE SUN IF YOU HAVE A SAFE METHOD OF DOING SO, SUCH AS A CELESTRON SOLAR FILTER.

2. TELESCOPE ASSEMBLY

Please refer to Figure 1 (and the identifying parts list) as you assemble the telescope.

A.The telescope and all items are packed in one box. Included with all models are:

•Telescope Optical Tube

•German Equatorial Mount

•Adjustable Tripod

•Star Pointer Finderscope and Bracket

•Counterweight Shaft and Counterweight

•Tripod Accessory Tray

•Declination Cable

•Right Ascension Cable

•20mm Eyepiece - 1¼"

•10mm Eyepiece - 1¼"

•The Sky® CD-ROM

To set up the tripod, locate the German equatorial mount, the tripod legs, the tripod mounting hardware and the tripod accessory tray.

1.Extend the center portion (#35) of each of the three tripod legs down 6-8".

2.Use the three tightening screws (#34) to secure each of the extended legs by threading these screws through the holes in the brackets at the bottom of each leg. It is important that you extend the legs before the equatorial mount is attached, otherwise the inner legs may become difficult to slide down. Fine tuning of the tripod height can be done later, and the tightening screws can be adjusted to secure the telescope at the desired height

3.Slide the two top portions of each tripod leg around the sides of each flange on the tripod head (#38) of the equatorial mount, so the flange is secured between them.

4.Slide the screw through the tripod leg and flange, until the screw extends out the other side.

5.Slide the washer and the nut over the screw and tighten. This can be left slightly loose, to allow for positioning the legs later, when attaching the accessory tray.

6.Repeat this process for the remaining two legs. Now the tripod will stand by itself.

You are now ready to attach the tripod accessory tray.

7.The tripod tray fits over the holes in the tripod leg brace. Insert the winged bolts through the holes in the bottom of the tripod leg brace and thread them into the holes in the accessory tray. Tighten all bolts to ensure proper stability to the mount.

B.Before proceeding further, locate Right Ascension (#24) and Declination knobs (#22) and tighten them finger tight.

1.Locate the declination cable holder (#13). Locate the declination cable (the shorter of the two cables) and attach the cable (#18) to the cable holder by tightening the thumb screw on the cable end. The thumb screw should be tightened down hard on the flat surface of the cable holder after backing off the cable about 1/4" from being fully engaged. This method helps ensure there is no slippage when using the cable.

2.You may reverse the position orientation of the Declination cable to suit your preference if desired.

3.Locate the right ascension cable holder (#27). Locate the right ascension cable (#31) and attach it the same way as the declination cable was attached in the last section.

Before mounting the optical tube, the counterweight must be attached to the mount:

1.Slide the counterweight shaft (#29) through the counterweight (#30). Use the counterweight lock to lock the counterweight in place. By holding the counterweight in one hand, thread the counterweight shaft clockwise into the equatorial mount as shown in figure 1.

C.Now you are going to put the telescope optical tube (#11) onto the equatorial mount. For models #31041 and #31044:

1.Slightly loosen the screws that hold the mounting rings on the telescope in place.

2.Slide the rings apart so that each is at the same distance as the holes in the mounting platform.

3.Place the telescope tube on the mount so that the flat portion of the tube rings rest on the mounting platform.

4.Align the holes on the square extrusions with the holes at the ends of the mounting platform.

5.Starting with the ring closest to the focuser end of the tube, insert the bolt through the hole in the mounting platform and thread it into the mounting ring. Repeat this process for the remaining mounting ring.

+ 10 hidden pages