CatEye CC-VT100W User Manual

1

3
2

VECTRA Wireless

CYCLOCOMPUTER
CC - VT100W

Owner’s Manual

12

3

4

U.S. Pat. Nos. 4633216/4636769/4642606/5236759 and Design Pat. Pending
Copyright© 2005 CATEYE Co., Ltd.

CCVT1W-050113 066600380

5

6

7

8

ENG

®

1

Max.

Max.

2

Component name

1 Bracket
2 Speed Sensor A
3 Magnet
4 Bracket Rubber Pad
5 Sensor Rubber Pad
6 Nylon Ties (L x2)
7 Nylon Ties (S x2)
8 Double-sided tape

Distance

Distance

70 cm

70 cm

3
2

1

8

8

1

1

7

or

1

1

4

2

7

5

23

A

2

3

3

SENSOR

SENSOR
ZONE

ZONE

B

3

5 mm

6

SENSOR ZONESENSOR ZONE

2

2

CC-VT100W VECTRA Wireless

1

SETTING

ENG

All Clear

PUSH!

AC

Select km/h or mph

START km/h

Tire size

ETRTO

47-305

47-406

47-507

23-571

37-590

40-559
47-559
50-559
54-559

57-559

57-559

32-630

18-622

20-622
23-622
25-622
28-622

32-622

37-622

40-522

14 x 1.50
14 x 1.75
16 x 1.50
16 x 1.75
18 x 1.50
18 x 1.75
20 x 1.75
20 x 1-3/8
22 x 1-3/8
22 x 1-1/2
24 x 1
24 x 3/4 Tubular
24 x 1-1/8
24 x 1-1/4
24 x 1.75
24 x 2.00
24 x 2.125
26 x 7/8
26 x 1(59)
26 x 1(65)
26 x 1.25
26 x 1-1/8
26 x 1-3/8
26 x 1-1/2
26 x 1.40
26 x 1.50
26 x 1.75
26 x 1.95
26 x 2.00
26 x 2.10
26 x 2.125
26 x 2.35
26 x 3.00
27 x 1
27 x 1-1/8
27 x 1-1/4

27 x 1-3/8

650 x 35A
650 x 38A
650 x 38B
700 x 18C
700 x 19C
700 x 20C
700 x 23C
700 x 25C
700 x 28C
700 x 30C
700 x 32C
700C Tubular
700 x 35C
700 x 38C
700 x 40C

L (cm)

BATTERY

COMPUTER

COIN

Close

Open

Mx

Odo

Dst

SET : km/h

MODE

Wheel Circumference

102
106
119
120
134
135
152
162
177
179
175
178
179
191
189
192
196
192
191
195
195
190
207
210
200
201
202
205
206
207
207
208
217
215
216
216

217

209
212
211
207
208
209
210
211
214
217
216
213
217
218
220

E

CR2032

TIRE

OPERATION FLOW

Current Speeed

0.0 (4.0) - 105.9 km/h
[0.0 (3.0) - 65.9 mph]

MODE

a

0

MODE

SET

L cm

1

-

x

3

7

/

2

8

RESET

Mx
Dst

2 sec

0

Clock Setting

24 hr [12 hr]

MODE

ODO Manual Set

(00000.0 - 99999.9)

START 00000.0 00001.0 00001.0 10001.0

2 sec

TIRE : 27x1-3/8 SET : L = 217 cm

(100 - 299 cm)

START 205

MODE

SET SET SET

MODE MODE

MODE

SET

0 - 23 [1 - 12]

A

C

D

B

SET

E

AC

SET : 10001.0 km

SET

206 207 217

MODE

MODE

SETTING END

RESET

Mx

0.0(4.0)-105.9 km/h
[0.0(3.0)-65.9 mph]

Odo

0-9999.9
10000-99999 km[mile]

Dst

0.00-999.99 km [mile]

0:00-23:59
[1:00-12:59]

SET

00 - 59

SET

RESET

RESET

c

Wheel
Circumference

SET

(100 - 299 cm)

SET

b

L cm

MODE

CC-VT100W VECTRA Wireless

SENSOR

All Clear

COIN

Close

Open

a

MODE

CR2032

MODE

MODE

2

CAUTION

CO

.,LTD.

• Do not concentrate on the computer while riding. Be
sure to ride safely!

• Install the magnet, sensor, and bracket securely. Check
these periodically.

• Dispose of used batteries according to local regula­tions. If swallowed, consult a doctor immediately.

• Avoid having the computer in hot direct sunlight for
extended periods.

• Do not disassemble the computer.

• Clean the computer and accessories with a soft cloth
dampened with a neutral detergent. Do not use
thinners, benzene, or alcohol on the computer.

Wireless Sensor

The sensor was designed to receive signals within a lim­ited range to prevent sensor signal interference. Thus,
the sensor and computer must be relatively close. If the
temperature or battery power is low, they may need to
be even closer than normal. The sensor must be installed
at the top of the fork, and the distance between the sen­sor and the computer should not exceed approximately
70 cm. Install the computer on the stem, with its bot­tom surface facing the sensor. (Take into account the
angle of the stem.)

Interference may occur, resulting in malfunction, if the
computer is:

• Near a TV, PC, radio, motor, or in a car or train.

• Close to a railroad crossing, railway tracks, TV sta­tions and or radar base.

• Close to a second bicycle with wireless sensors.

Correct installation of sensor and magnet

Attach the magnet 3 so that it passes through the sensor

A

zone of the sensor 2.

B

Be sure to have a 5 mm-or-less clearance between the sensor
2 and magnet 3.

Part names

A

Current Speed
Sensor signal reception icon

B

Flashes in sync with sensor signals.

C

Speed unit

Mode symbol ......................................................

D

Indicates the mode currently selected.

Mx .............. [Maximum Speed]

Odo ............. [Total Distance]

Dst .............. [Trip Distance]

.............. [Clock]

E

Battery Case Cover

Starting/Stopping measurement

This computer automatically starts measurement when
the bicycle is moving.

Switching Mode symbol ......................

Press the MODE button to cycle through different func­tions, which are listed in the OPERATION FLOW chart.

Resetting data ..................................

As shown in the OPERATION FLOW, press the MODE
button to clear data when
The trip distance cannot be reset.

Power-saving function

If the computer has not received a signal for 10 min­utes, power-saving mode will activate and only the clock
will be displayed. When the computer receives a sensor
signal again, the measuring screen reappears. If the unit
remains inactive for two weeks, the unit enters SLEEP
mode. Press the MODE button to stop SLEEP mode.

Setting the clock ...............................

With the symbol displayed, press the SET button to
set the clock.
Press the MODE button to move time forward. The value
changes more rapidly if the button is pressed and held.
Press the SET button to move from the “hour” to "min­utes" digit. Press the SET button again to set the clock,
and revert to the measuring screen.
* If the unit of speed is set to km/h, the 24-hour time

system is activated. When set to mph, the 12-hour sys­tem applies.

Maintenance

To clean the computer or accessories, use diluted neu­tral detergent on a soft cloth, and then wipe it off with a
dry cloth.

RESET

appears on the screen.

b

b

b

c

Troubleshooting

No display.

Is battery in the computer run down?
Replace it, and re-enter the correct information.
(All Clear a).

Incorrect data appears.

Do all clear operation. (All Clear a).

The sensor signal icon does not flash. (The speed is not dis­played.)
[If the signal icon does not flash, reduce the distance be­tween the sensor and computer, adjust the position of the
magnet, and spin the wheel again. If the icon now flashes,
this indicates that the computer and sensor are too far apart
or that the battery is low.]

Is the clearance between the sensor and magnet too great?
Does the magnet pass through the sensor zone?
Adjust the positions of the magnet and sensor.

Is the computer installed at the correct angle?
Install the computer with its bottom surface facing the sensor.

Is the distance between the computer and sensor too great?
Install the sensor closer to the computer.

Is the sensor battery weak?
In cold weather, battery performance degrades.
Replace it.

Is the computer’s battery weak?
Replace it with a new one. (All Clear a).

Replacing the Battery

• Computer

If the display appears faded or sensor reception is poor,
replace the battery. The Total Distance can be entered
manually. Before removing the battery, note the cur­rent Total Distance. Install a new lithium battery
(CR2032) with the (+) side facing upward.
Then re-start the computer according to the SETTING
procedure, and then set the clock.
* When the batteries in either the main unit or sensor

run down, please replace both the sensor and main
unit batteries.

• Sensor

If sensor reception is poor, replace the battery. Then
check the positions of the battery and magnet.

c

Specification

Battery ........... Computer: Lithium Battery CR2032 X 1

Battery Life .... Computer: Approx. 1 year

Controller ............................. 4-bit 1-chip microcomputer

Display ................................. Liquid crystal display

Sensor ................................. No cont act magnetic sensor

Wheel Circumference Range 100 cm - 299 cm

Working Temperature .......... 0°C - 40°C (32°F - 104°F)

Dimension/Weight ............... 40 x 55 x 21 m m [1-4/7” x 2-1/6” x

* The factory-loaded battery life might be shorter than the above-

* The specifications and design are subject to change without

Sensor: Lithium Battery CR2032 X 1

(On the basis that the computer is used for 1 hour/
day)
Sensor: until Total Distance reaches about

* This is the average figure of being used under 20°C tempera-

ture and the dis tance between the computer and the sensor
is 65 cm.

mentioned specification.

notice.

10,000 km (6,250 mile)

(crystal controlled oscillator)

5/6”] / 30 g [1.06 oz]

Standard Parts

#169-6590

Parts Kit

#169-6580

Speed Sensor A

#169-6570

Bracket kit

#169-9691

Wheel Magnet

#166-5150

Lithium Battery (CR2032)

Option Parts

#169-6667

Center Mount Kit

#169-9760

Magnet for Composite Wheel

#169-9690

Hi-Power Wheel Magnet

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Modifications The FCC requires the user to be notified that any changes or modifications
made to this device that are not expressly approved by CatEye Co., Ltd. May void the user’s
authority to operate the equipment.

LIMITED WARRANTY - 2-Year Computer/Sensor only

(Accessories/Attachments and Battery Consumption excluded)

If trouble occurs during normal use, the part of the Main Unit or sensor will be repaired or
replaced free of charge. The service must be performed by CatEye Co., Ltd. To return the prod­uct, pack it carefully and remember to enclose the warranty certificate with instruction for repair.
Please write or type your name and address clearly on the warranty certificate. Insurance, han­dling and transportation charges to our service shall be borne by person desiring service.

Service & Research Address for USA

2-8-25, Kuwazu, Higashi Sumiyoshi­ku, Osaka 546-0041 Japan
Attn: CATEYE Customer Service Section

CATEYE Service and Research Center
1705 14th St. 115 Boulder, CO 80302
Phone: [phone]
Toll Free: 800.5CATEYE
Fax: [phone]
E-mail: [e-mail]
URL: http://www.cateye.com

ENG

CC-VT100W VECTRA Wireless

3