Cateye CC-TR200DW User Manual

CATEYE V2c/V3

START

CC-TR200DW/300TW

Quick Start

Click the button and follow the in­structions.

Thank you for purchasing our cyclocomputer CATEYE V2c/V3.

Next

This Quick Start Manual explains how to set up the computer, how to install the unit to your
bicycle, and how to wear the heart rate sensor.
Please set up the unit according to the specified procedure, then it will be ready for use as a
cyclocomputer.

• Before use, read the instruction manual that comes with the product thoroughly
to the end to understand the functions of this unit, and to use it safely in a
correct manner.
Pacemaker users must not use the heart rate sensor provided with V3 •
(TR300TW).

This PDF contains a movie file.

Next

When you click on the movie screen, a message regarding security appears. Click the
“Trust in the text” or “Play” button to close the message.
Click the screen again to play the movie.

CATEYE V2c / V3

Return to a Cover

Setting up the computer

How to install the speed sensor (movie)

How to wear the heart rate sensor (movie) * V3 (TR300TW) only

How to install the bracket (movie)

Quick Start Manual

Click the item you wish to view.

Contents

Operation of buttons

SSE

M1/

+

M2/-

MENU

Next

Set up the computer by operating the buttons as follows.
Check the button position before you start setting up.

Front Back

Press the SSE button, the M1/+ but­ton, and the M2/- button on the front
of the computer.

Press the MENU button on the back of
the computer.

CATEYE V2c / V3

Insulation sheet

Open

Close

Return to Contents

Next

Return

Quick Start Manual

Preparation for setting up

Restarting operation

Setting the date display

Setting the year

Setting the month

Setting the day

Setting the clock display

Setting the hour

Setting the minute

Setting up the computer

Preparation for setting up

Open the battery cover on the back of the computer
using a coin, and then pull out the insulation sheet.

After pulling out, replace the battery cover as before. *

Setting the wheel

Setting the speed unit

Measuring screen

(Setup completed)

CATEYE V2c / V3

AC

Return to Contents

Next

Return

Quick Start Manual

Preparation for setting up

Restarting operation

Setting the date display

Setting the year

Setting the month

Setting the day

Setting the clock display

Setting the hour

Setting the minute

Setting up the computer

Restarting operation

Press the AC button on the back of the computer.
After full lighting of the screen, the computer changes

to the date display setting screen to start setting up.

Setting the wheel

Setting the speed unit

Measuring screen

(Setup completed)

Full lighting Setting the date display

CATEYE V2c / V3

SSE

M1/

+

M2/-

Return to Contents

Next

Return

Quick Start Manual

Preparation for setting up

Restarting operation

Setting the date display

Setting the year

Setting the month

Setting the day

Setting the clock display

Setting the hour

Setting the minute

Date display

Setting up the computer

Setting the date display

When the M1/+ button or the M2/- button is pressed, either
“YY/MM/DD”, “MM/DD/YY” or “DD/MM/YY” is selected
for the date display. Select the display of your choice.

After selecting, press the SSE button to proceed to the
next step “Setting the year”.

The following description is for the case when *
“YY/MM/DD” is selected.

YY/MM/DD

↔ ↔

MM/DD/YY

To the next step

Setting the wheel

Setting the speed unit

Measuring screen

(Setup completed)

DD/MM/YY

CATEYE V2c / V3

SSE

M1/

+

M2/-

Return to Contents

Next

Return

Quick Start Manual

Preparation for setting up

Restarting operation

Setting the date display

Setting the year

Setting the month

Setting the day

Setting the clock display

Setting the hour

Setting the minute

Setting up the computer

Setting the year

Pressing the M1/+ button increases the value (“Year” of
the date) flashing, and pressing the M2/- button decreas­es it. Enter any value.

After entering, press the SSE button to proceed to the next
step “Setting the month”.

Year

Increase the value To the next step

Setting the wheel

Setting the speed unit

Measuring screen

(Setup completed)

CATEYE V2c / V3

SSE

M1/

+

M2/-

Return to Contents

Next

Return

Quick Start Manual

Preparation for setting up

Restarting operation

Setting the date display

Setting the year

Setting the month

Setting the day

Setting the clock display

Setting the hour

Setting the minute

Setting up the computer

Setting the month

Pressing the M1/+ button increases the value (“Month”
of the date) flashing, and pressing the M2/- button de­creases it. Enter any value.

After entering, press the SSE button to proceed to the next
step “Setting the day”.

Month

Increase the value To the next step

Setting the wheel

Setting the speed unit

Measuring screen

(Setup completed)

CATEYE V2c / V3

SSE

M1/

+

M2/-

Return to Contents

Next

Return

Quick Start Manual

Preparation for setting up

Restarting operation

Setting the date display

Setting the year

Setting the month

Setting the day

Setting the clock display

Setting the hour

Setting the minute

Setting up the computer

Setting the day

Pressing the M1/+ button increases the value (“Day” of
the date) flashing, and pressing the M2/- button decreas­es it. Enter any value.

After entering, press the SSE button to proceed to the next
step “Setting the clock display”.

Day

Increase the value To the next step

Setting the wheel

Setting the speed unit

Measuring screen

(Setup completed)

CATEYE V2c / V3

SSE

M1/

+

M2/-

Return to Contents

Next

Return

Quick Start Manual

Preparation for setting up

Restarting operation

Setting the date display

Setting the year

Setting the month

Setting the day

Setting the clock display

Setting the hour

Setting the minute

Clock display

Setting up the computer

Setting the clock display

When the M1/+ button or the M2/- button is pressed, ei­ther “12h” or “24h” is selected for the clock display. Se­lect the display of your choice.

After selecting, press the SSE button to proceed to the
next step “Setting the hour”.

24h

↔

12h

To the next step

Setting the wheel

Setting the speed unit

Measuring screen

(Setup completed)

CATEYE V2c / V3

SSE

M1/

+

M2/-

Return to Contents

Next

Return

Quick Start Manual

Preparation for setting up

Restarting operation

Setting the date display

Setting the year

Setting the month

Setting the day

Setting the clock display

Setting the hour

Setting the minute

Setting up the computer

Setting the hour

Pressing the M1/+ button increases the value (“Hour” of
the clock) flashing, and pressing the M2/- button decreas­es it. Enter any value.

After entering, press the SSE button to proceed to the next
step “Setting the minute”.

Hour

Increase the value To the next step

Setting the wheel

Setting the speed unit

Measuring screen

(Setup completed)

CATEYE V2c / V3

M1/

+

M2/-

MENU

Return to Contents

Next

Return

Quick Start Manual

Preparation for setting up

Restarting operation

Setting the date display

Setting the year

Setting the month

Setting the day

Setting the clock display

Setting the hour

Setting the minute

Setting up the computer

Setting the minute

Pressing the M1/+ button increases the value (“Minute”
of the clock) flashing, and pressing the M2/- button de­creases it. Enter any value.

After entering, press the MENU button to change to the Measuring
screen, and then proceed to the next step “Setting the wheel”.

When the tire circumference of your bicycle is 2096 mm (700x23c), *
and the speed unit uses “km”, setting up is completed. Proceed to
the following procedure only when you wish to make changes.

Minute

Increase the value To the next step

Setting the wheel

Setting the speed unit

Measuring screen

(Setup completed)

CATEYE V2c / V3

MENU

V3

V2c

or

M2/- M2/-

M2/-

M2/-

M2/-

M2/-

M2/-

M2/-

M2/-

M2/-

SSE

Return to Contents

Next

Return

Quick Start Manual

Preparation for setting up

Restarting operation

Setting the date display

Setting the year

Setting the month

Setting the day

Setting the clock display

Setting the hour

Setting the minute

Setting the wheel

Press the MENU button to change to the FILE VIEW screen.
Press the M2/- button twice to change to the WHEEL setting screen, and press

the SSE button to proceed to “Setting the wheel (1/3)”.

Measuring

screen

Setting up the computer

Wheel screen

To the next step

Setting the wheel (1/3)

Setting the speed unit

Measuring screen

(Setup completed)

CATEYE V2c / V3

SSE

Return to Contents

Next

Return

Quick Start Manual

Preparation for setting up

Restarting operation

Setting the date display

Setting the year

Setting the month

Setting the day

Setting the clock display

Setting the hour

Setting the minute

Setting up the computer

Setting the wheel

When “A” flashes after changing to the WHEEL setting
screen, press the SSE button to proceed to the next step
“Setting the wheel (2/3)”.

Tire circumference A

To the next step

Setting the wheel (2/3)

Setting the speed unit

Measuring screen

(Setup completed)

CATEYE V2c / V3

M1/

+

M2/-

SSE

MENU

Return to Contents

Next

Return

Tire circum-

ference refer-

ence table

Quick Start Manual

Preparation for setting up

Restarting operation

Setting the date display

Setting the year

Setting the month

Setting the day

Setting the clock display

Setting the hour

Setting the minute

Entering the tire

circumference

Setting up the computer

Setting the wheel

Enter the tire circumference (mm) of your bicycle with 4
digits using the tire circumference reference table.

Pressing the M1/+ button increases the value flashing,
and pressing the M2/- button decreases it. Pressing the
SSE button moves to the next two digits.

After entering, press the MENU button to proceed to the
next step “Setting the speed unit”.

Increase the value Move digit

To the next step

Setting the wheel (3/3)

Setting the speed unit

(Setup completed)

Measuring screen

CATEYE V2c / V3

MENU

V3

V2c

or

M2/-

M2/-

M2/- M2/-

M2/-

M2/-

M2/-

M2/-

M2/-

M2/-

SSE

Return to Contents

Next

Return

Quick Start Manual

Preparation for setting up

Restarting operation

Setting the date display

Setting the year

Setting the month

Setting the day

Setting the clock display

Setting the hour

Setting the minute

Setting up the computer

Setting the speed unit

Press the M2/- button twice to change to the UNIT setting screen, and press the
SSE button to proceed to “Setting the measurement unit”.

Unit

screen

Measuring

screen

To the next step

Setting the wheel

Setting the speed unit (1/2)

Measuring screen

(Setup completed)

CATEYE V2c / V3

M1/

+

M2/-

MENU

Return to Contents

Next

Return

Quick Start Manual

Preparation for setting up

Restarting operation

Setting the date display

Setting the year

Setting the month

Setting the day

Setting the clock display

Setting the hour

Setting the minute

Setting the speed unit

Setting up the computer

Setting the speed unit

When the M1/+ button or the M2/- button is pressed, ei­ther “km” or “mile” is selected for the measurement unit.
Select the display of your choice.

After selecting, press the MENU button twice to return to
the measuring screen.

↔

km/h

mph

Setup is completed.

To the measuring screen

Setting the wheel

Setting the speed unit (2/2)

Measuring screen

(Setup completed)

(Press twice)

CATEYE V2c / V3

Return to Contents

Next

Return

Return to Contents

Quick Start Manual

Preparation for setting up

Restarting operation

Setting the date display

Setting the year

Setting the month

Setting the day

Setting the clock display

Setting the hour

Setting the minute

Setting up the computer

Now, setup of the computer is completed.

If the bracket and speed sensor are not installed on your
bicycle, return to Contents, click the movies of how to
install the bracket and speed sensor, and install them ac­cording to the instructions.

When V3 (TR300TW) is used, see also “How to wear the
heart rate sensor (movie)”.

Measuring screen

Setting the wheel

Setting the speed unit

Measuring screen

(Setup completed)

CATEYE V2c / V3

Return to Contents

Quick Start Manual

How to install the bracket

CATEYE V2c / V3

Return to Contents

Quick Start Manual

How to install the speed sensor

CATEYE V2c / V3

Return to Contents

Quick Start Manual

How to wear the heart rate sensor

CATEYE V2c / V3

L mm

Return to Contents

Return

Quick Start Manual

Tire circumference reference table

Tire size

ETRTO

47-203 12x1.75 935
54-203 12x1.95 940
40-254 14x1.50 1020
47-254 14x1.75 1055
40-305 16x1.50 1185
47-305 16x1.75 1195
54-305 16x2.00 1245
28-349 16x1-1/8 1290
37-349 16x1-3/8 1300
32-369 17x1-1/4 (369) 1340
40-355 18x1.50 1340
47-355 18x1.75 1350
32-406 20x1.25 1450
35-406 20x1.35 1460

L (mm)

Measure the tire circumference (L) of your bicycle

Tire size

ETRTO

40-406 20x1.50 1490
47-406 20X1.75 1515
50-406 20x1.95 1565
28-451 20x1-1/8 1545
37-451 20x1-3/8 1615
37-501 22x1-3/8 1770
40-501 22x1-1/2 1785
47-507 24x1.75 1890
50-507 24x2.00 1925
54-507 24x2.125 1965
25-520 24x1 (520) 1753

24x3/4 Tubular 1785
28-540 24x1-1/8 1795
32-540 24x1-1/4 1905

L (mm)

Tire size

ETRTO

25-559 26x1 (559) 1913
32-559 26x1.25 1950
37-559 26x1.40 2005
40-559 26x1.50 2010
47-559 26x1.75 2023
50-559 26x1.95 2050
54-559 26x2.10 2068
57-559 26x2.125 2070
58-559 26x2.35 2083
75-559 26x3.00 2170
28-590 26x1-1/8 1970
37-590 26x1-3/8 2068
37-584 26x1-1/2 2100

650C Tubular 26x7/8 1920

L (mm)

Setting up the computer

Tire size

ETRTO

20-571 650x20C 1938
23-571 650x23C 1944
25-571 650x25C 26x1 (571) 1952
40-590 650x38A 2125
40-584 650x38B 2105
25-630 27x1 (630) 2145
28-630 27x1-1/8 2155
32-630 27x1-1/4 2161
37-630 27x1-3/8 2169
18-622 700x18C 2070
19-622 700x19C 2080
20-622 700x20C 2086

23-622

700x23C 2096

25-622 700x25C 2105

L (mm)

Tire size

ETRTO

28-622 700x28C 2136
30-622 700x30C 2146
32-622 700x32C 2155

700C Tubular 2130
35-622 700x35C 2168
38-622 700x38C 2180
40-622 700x40C 2200
42-622 700x42C 2224
44-622 700x44C 2235
45-622 700x45C 2242
47-622 700x47C 2268
54-622 29x2.1 2288
60-622 29x2.3 2326

L (mm)

Adjust the tire pressure properly. With the rider’s weight applied on the bicycle,
roll the wheel one tire revolution with reference to a marker such as the valve, and
measure the travel distance on the ground.