Casio CP-725 Manual
|
|
|
|
|
PAGE |
HANDSET FEATURES |
PAGE |
|
1 |
1 |
|
|
|
|
|
Talk (page 7-11)
Redial (page 11, 23)
Channel (page 5, 9)
Battery (page 12,30)
Left Arrow, (page 20, 24)
Delete (page 21)
Autodial (page 18-23)
Down Arrow (page 15-27)
Caller ID (page 13-17)
TALK |
|
FLASH |
|
|
|
REDIAL |
CHANNEL |
HOLD |
|
|
PAUSE |
1 |
2 ABC |
3 DEF |
4 GHI |
5 JKL |
6MNO |
7 PRS |
8 TUV |
9WXY |
TONE |
0OPER |
# |
BATTERY |
PROGRAM |
NAME/DATE |
AUTO |
DELETE |
SEND |
CALLER ID
25 CHANNEL
Flash/Call Waiting (page 9,14)
Hold (page10)
Pause (page 19)
Name/Date (page 15)
Right Arrow (page 18, 20, 22-27)
Program (page 18, 24-27)
Send (page10, 11, 16, 19)
LCD Display
Up Arrow (page 15-27)
PAGE
2 INITIAL SETUP
INSTALLATION
1PLUG the CP-725’s telephone cord into a telephone wall jack.
TO WALL JACK
TONE PULSE
USE ONLY WITH
ADAPTOR M/N-14
CONNECT the AC Adapter Plug into the AC 2Adapter Outlet on the back of the CP-725 charging
cradle. LOOP the cord through the AC Adapter Cord Holder to prevent accidental disconnection.
3PLUG the AC Adapter into an electrical wall outlet. The LEDs on the charging cradle will stop flashing when the handset (with battery pack installed) is placed in the cradle. NOTE: If the telephone cord is not properly plugged into the telephone wall jack, the CHARGING INDICATOR will flash when the handset is out of the charging cradle.
|
|
|
SWITCH SETTINGS |
PAGE |
|
3 |
|
|
|
|
|
4It may be necessary to set the TONE/ PULSE SWITCH. See below.
5Fully extend the charging cradle antenna for clear reception.
TONE/PULSE SWITCH
This switch tells the CP-725 to dial out with either touchtone or pulse signals to match the service you have with your local telephone company. The CP-725 is shipped with the
TONE/PULSE SWITCH in the TONE position. If you do not have touchtone service, set the switch to pulse on the back of the charging cradle.
TONE PULSE
RINGER ON/OFF
Your CP-725's ringer is preset to "ON". To reset the ringer to "ON" or "OFF":
1Press PROGRAM. The "Program
Mode" display will flash:
BATTERY |
PROGRAM |
NAME/DATE |
PROGRAM MODE
2Press the RIGHT ARROW KEY once. The "Ringer" display will appear, for example:
BATTERY |
PROGRAM |
NAME/DATE |
RINGER: ON
3Press the DOWN or UP ARROW KEY to change the ringer setting (turn it ON or OFF).
CALLER ID
TONE = for Touchtone systems |
Press PROGRAM again to lock in |
|
4your selection. |
||
PULSE = for Rotary dialing or Pulse systems |
PAGE IMPORTANT SAFETY
4 INSTRUCTIONS
INSTALLATION INSTRUCTIONS
1. Never install telephone wiring during a lightning storm.
2. Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.
3. Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.
4. Use caution when installing or modifying telephone lines.
When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following:
1.Read and understand all instructions.
2.Follow all warnings and instructions marked on the product.
3.Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
4.Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool.
5.Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious damage to the product.
6.Slots and openings in the cabinet and the back or bottom are provided for ventilation. To protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the product on the bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heat register. This product should not be placed in an enclosed environment unless proper ventilation is provided.
7.Do not allow anything to rest on the power cord. Do not locate this product where the cord will be abused by persons walking on it.
8.Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock.
9.Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock. Never spill liquid of any kind on the product.
10.To reduce the risk of electric shock, do not disassemble this product, but take it to a qualified serviceperson when service or repair work is required. Opening or removing covers may expose you to dangerous voltages or other risks. Incorrect re-assembly can cause electric shock when the appliance is subsequently used.
11.Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:
A.When the power supply cord or plug is damaged or frayed.
B.If liquid has been spilled into the product.
C.If the product has been exposed to rain or water.
D.If the product does not operate normally by following the operating instructions. Adjust only those controls, that are covered by the operating instructions because improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation.
E.If the product has been dropped or the cabinet has been damaged.
F.If the product exhibits a distinct change in performance.
12.Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.
13.Do not use the telephone to report a gas leak near the leak.
SAVE THESE INSTRUCTIONS
IMPORTANT CORDLESS |
|
|
PAGE |
|
|
TELEPHONE INFORMATION |
5 |
|
|
|
|
Interference Information
Notice: This cordless telephone uses radio communications between the handset and the base unit, and may not ensure privacy of communication. Other devices including other cordless telephones
may interfere with the operation of this cordless telephone or cause noise during operation. Cordless telephone equipment generates and receives radio waves and, if not installed and used properly, may pick up interference. To
prevent interference:
Avoid locations such as heating appliances, electrical equipment (e.g., fluorescent lamp, TV, radio, refrigerator, computer), places subject to direct sunlight, excessive dust, moisture, vibration, etc.
Locate the base unit in a high place in the house (such as the second floor) in order to receive the most effective communication range. Fully extend the base unit antenna. Telephones must not cause interference to any licensed radio service.
WARNING
To prevent fire or shock hazard, do not expose the set to rain or moisture.
To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.
CAUTION
1. Use batteries only intended for recharging. Use only the following battery pack: Nickel-Cadmium Rechargeable, 3.6 volts, 250-300 mAh.
2.Do not dispose of the battery(ies) in a fire. The cell(s) may explode. Check with local codes for special disposal instructions.
3.Do not open or mutilate the battery(ies.) Released electrolyte is corrosive and may cause
damage to the eyes or skin. It may be toxic if swallowed.
4.Exercise care when handling the battery(ies) in order not to short the battery(ies) with conducting materials such as rings, bracelets, and keys. The battery or conductor may overheat and cause burns.
CONTAINS: NICKEL-CADMIUM
RECHARGEABLE BATTERY.
MUST BE RECYCLED OR
DISPOSED OF PROPERLY.
Ni-Cd
Charge the Handset Batteries Before Using the Cordless Telephone
The batteries lose their charge during shipping and storage. Be sure to charge the batteries before you use the CP-725 cordless telephone. Place the handset in the charging cradle. The CHARGING INDICATOR will light. Leave the handset in the charging cradle for 12-15 hours.
Digital Security Code
The Digital Security Coding System automatically resets a new personal security code to one of 256 combinations every time you return the CP-725 handset to the charging cradle. (Whenever the handset is returned to the charging cradle you will hear a beep confirming that a new security code has been set.) The security code prevents unauthorized use of your telephone line, false rings, and false dialing. (US. Patent No. 5,073,932)
Ultra Clear® Noise Reduction Circuit
The CP-725 is equipped with Ultra Clear Noise Reduction Circuitry (Compander Circuit). It reduces background noise—reception is superior to conventional cordless telephones.
25 Channels with Optimum Channel Memory (OCMTM)
The CP-725 accesses 25 channels with Optimum Channel Memory providing fast and clear channel selection. The scanning circuit scans all 25 channels in your neighborhood to find the best available channel. Once it finds the clear channels, it selects and remembers the three best ones. When you press the “Talk” key to call out or receive a call, the unit automatically provides you with the best channel. Whenever you place the handset in the charging cradle for 2 seconds or more, the unit updates its memory. Press TALK and then CHANNEL if you wish to change channels manually. (U.S. Patents 5,197,093 & 5,418,839)
PAGE IMPORTANT CP-725
6 INFORMATION
Caller ID
If you subscribe to a Caller Identification Service (available from most local telephone companies), the CP-725 can display the name and phone number of incoming calls. With the Caller ID feature, you can see who is calling before you answer a call.
Call Waiting Caller ID
If you subscribe to a Call Waiting Caller ID service from your local telephone company, the CP-725 can display the name and number of an incoming call while you are already talking to another party on the cordless handset.
Caller ID Memory
The CP-725 automatically stores the Caller ID names and numbers of the last 25 calls you have received.
Supertwist Nematic (STN) LCD
Advanced LCD technology in your CP-725 provides clear, multi-angle viewing of caller's name and phone number if you subscribe to Caller ID service from your local telephone company.
Autodial Memory Backup
CASIO PHONEMATE’s memory backup system maintains up to 20 autodial names and numbers indefinitely until you erase them. This non-volatile memory does not require battery power.
Charging The Batteries
Charge the batteries for 12-15 hours before using the cordless handset for the first time. The handset is always charging while it is in the charging cradle and cannot be overcharged.
To charge the batteries, first check the AC Adapter to see that it is connected correctly. Then, place the handset in the charging cradle. The CHARGING INDICATOR on the charging cradle lights to indicate that the CP-725 is charging.
Local Area Code Setting
If you are planning to use the Caller ID features on the CP-725, be sure to program your local area code into the handset's memory after you have charged the batteries for the first time. The CP-725 needs this information to operate correctly when dialing stored Caller ID numbers. (see page 25.)
HANDSET / TELEPHONE |
|
|
PAGE |
|
|
OPERATION |
7 |
|
|
|
STANDBY MODE
The CP-725 is in "Standby" mode whenever it is idle, waiting for a call. If the handset is in the charging cradle, the display will either show the ringer status, for example:
RINGER IS ON
2After this, the "Volume" display will appear:
3Wait for dial tone and dial the phone number. The number will appear in the display as you dial.
INDICATOR on the charging cradle lights to show the handset is in use.
OR
If you have new caller ID entries from recent unanswered calls, it will show the "New Callers" message:
<NEW CALLERS>
Press CALLER ID to view the name and number of "New Callers".
CALLER ID
If the handset is in "Standby Mode" but not in the charging cradle, the display will go blank after a short time to conserve battery power.
TO PLACE A CALL
1Pick up the handset and press TALK. The display will briefly show:
TALK |
SCANNING... |
|
CH03 |
||
|
VOLUME 
5551212
FLASH
TALK
REDIAL |
CHANNEL |
HOLD |
|
|
PAUSE |
1 |
2ABC |
3DEF |
4GHI |
5 JKL |
6MNO |
7PRS |
8TUV |
9WXY |
TONE |
0OPER |
# |
BATTERY |
PROGRAM |
NAME/DATE |
AUTO |
DELETE |
SEND |
This display indicates that the handset is establishing contact with the charging cradle. In this example, CH03 is the current channel number of 25 available channels in your area.
CALLER ID
PAGE
8 HANDSET / TELEPHONE
TO END A CALL
1To hang up, press TALK or return the handset to the charging cradle. NOTE: When you return the handset to the charging cradle, you are hanging up the phone and returning to Standby Mode. The CP-725 is now ready to receive a call and the CHARGING INDICATOR lights to show that the battery is charging.
HANDSET VOLUME
CONTROL
Whenever the CP-725 is in "Talk" mode, the handset volume will be displayed.
1Press the DOWN or UP ARROW KEY to adjust the volume.
TALK
IF YOU MISDIALED A
NUMBER
1Press TALK twice (“off” and “on.”) Wait for dial tone and dial the correct number.
TALK
VOLUME
CH03 00:01
2When TALK is pressed, the handset volume returns to the default level (see PROGRAMMING THE CP-725, "Default Volume", page 25).
TO RECEIVE A CALL
1When the phone rings, pick up the cordless handset and press TALK. You will briefly see the "Scanning" display, followed by the "Volume" display, as described under Placing a Call. Speak to the caller.
TALK
2To hang up, press TALK on the handset or return the handset to the charging cradle.
CALL TIMER
About 10 seconds after you enter "Talk" mode, a Call Timer will appear on the display:
VOLUME
CH07 00:53
The timer will automatically be reset whenever you place a new call.
NOTE: The length of time shown on the display is intended only to be an estimate duration of a phone call. CASIO PHONEMATE makes no guarantees regarding the accuracy of this timer.
OPERATION
TALK |
|
FLASH |
|
|
|
REDIAL |
CHANNEL |
HOLD |
|
|
PAUSE |
1 |
2ABC |
3DEF |
4GHI |
5 JKL |
6MNO |
7PRS |
8TUV |
9WXY |
TONE |
0OPER |
# |
BATTERY |
PROGRAM |
NAME/DATE |
AUTO |
DELETE |
SEND |
CALLER ID
25 CHANNEL
PAGE
(continued) |
9 |
|
LAST CALL TIME
DISPLAY
Press the RIGHT ARROW (NAME/
1DATE) key to view the approximate length of the last call after you have hung up the phone.
BATTERY |
PROGRAM |
NAME/DATE |
LAST CALL TIME: 01:38
CHANGING CHANNELS
MANUALLY
1After TALK is pressed, the CP-725 selects the best of 25 available channels in your area. If you hear noise or interference while using the CP-725, press CHANNEL on the handset to change channels.
REDIAL |
CHANNEL |
HOLD |
PAUSE
FLASH/CALL WAITING
If you subscribe to a call waiting service and you receive another call while using the phone, press FLASH to answer the second call. To return to the first call, press FLASH again.
FLASH may also be FLASH used on a business
phone system (CENTREX, PBX) for transferring calls.
PAGE
10 HANDSET / TELEPHONE
HOLD
You may place a call on hold while using the cordless handset.
1Press HOLD to place a call on hold. The following display will appear.
REDIAL |
CHANNEL |
HOLD |
PAUSE
HOLD
CH09 4:59
NOTE: You can place a call on hold for up to 5 minutes. During HOLD, do not return the handset to the charging cradle. Doing so will disconnect the caller.
TALK |
|
FLASH |
|
|
|
REDIAL |
CHANNEL |
HOLD |
|
|
PAUSE |
1 |
2ABC |
3DEF |
2To continue your phone conversation, press TALK, HOLD, or pick up an extension phone connected to the same line. When the extension phone is picked up, the CP-725 automatically disconnects itself from the line.
DIALING A NUMBER USING THE SEND KEY
Send-Key Dialing is extremely reliable because you can see the number you have entered before actually dialing it.
1Make sure the CP-725 is in "Standby Mode". Without pressing the TALK button, enter the number you wish to dial. If you make a mistake, use DELETE to make changes.
AUTO DELETE
5551212
4GHI |
5 JKL |
6MNO |
7PRS |
8TUV |
9WXY |
TONE |
0OPER |
# |
BATTERY |
PROGRAM |
NAME/DATE |
AUTO |
DELETE |
SEND |
CALLER ID
25 CHANNEL
2After you have correctly entered the entire number you wish to dial, press SEND. The CP-725 SEND
will dial the number.
|
OPERATION (continued) |
|
|
|
||
|
PAGE |
|
||||
|
11 |
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
||
|
REDIAL |
|
DISPLAY REDIALING |
|
||
|
|
|
|
|
|
|
The CP-725 remembers the last number you dialed. The redial memory will hold up to 16 digits. Every time you dial a new telephone number, the redial memory is updated with that new number.
1Press TALK and wait for a dial tone.
TALK
2Press REDIAL.
REDIAL |
CHANNEL |
HOLD |
PAUSE
REDIAL WHEN BUSY
If you receive a busy signal after placing a call and you wish to try again immediately, there is no need to hang up the phone.
1Press REDIAL while hearing a busy signal and the CP-725 will automatically hang up, reconnect, and dial the number again.
REDIAL |
CHANNEL |
HOLD |
PAUSE
Display Redialing allows you to view the contents of the redial memory before dialing. This is useful if you aren't sure what number was last dialed on the CP-725.
1Make sure the unit is in "Standby" mode. Press REDIAL. You will be able to view the last 14 digits of the last number dialed.
REDIAL |
CHANNEL |
HOLD |
PAUSE
13105551212
2Press SEND to dial.
SEND
PAGING THE HANDSET
FROM THE
CHARGING CRADLE
To page the handset from the charging cradle, the handset must be in “Standby” mode and the ringer must be set to ON.
1Press PAGE/FIND on the charging cradle. You will hear the handset ring.
PAGE/FIND
2To cancel the page, either press PAGE/ FIND a second time, press TALK on the handset or place the handset in the charging cradle.
page will stop.
PAGE
12 BATTERY & ALARM
BATTERY CONDITION
You can check the power level of the battery to avoid battery depletion.
1Press BATTERY when the handset is out of the charging cradle. The following display will appear when batteries are fully charged:
BATTERY |
PROGRAM |
NAME/DATE |
BATTERY
2As the battery discharges, the stack symbols will disappear, starting from the right. When the battery is low, the display will look like:
BATTERY
3Charge the battery for 12-15 hours before using the cordless handset for the first time.
BATTERY |
PROGRAM |
NAME/DATE |
AUTO |
DELETE |
SEND |
CALLER ID
25 CHANNEL
LOW BATTERY
INDICATOR
The CP-725 will automatically detect a low battery. If this happens, you will hear a double beep, and the "Low Battery" display will appear:
<LOW BATTERY>
If the Low Battery indicator appears while you are talking on the CP-725, you may only have a few minutes left before the battery discharges completely, in which case you will be disconnected. To prevent this, simply pick up an extension phone and place the CP-725 back in the charger. Place the handset in the charger for 12 - 15 hours to recharge the battery.
NOTE: The batteries can be recharged many times, but if you get a low battery indication even after 12-15 hours of charging, you should replace the battery pack. See page 35, the Accessories order form to purchase a battery pack.
OUT OF RANGE ALARM
The CP-725 cordless handset operates
like any other cordless handset. You can use it in the yard, at the pool, at the
mailbox, or any place within the operating
range of the charging cradle. If you move
out of the charging cradle’s operating
range, you may hear a warning tone and/ or static interference. Move closer to the charging cradle to deactivate the alarm. If you remain out of range for too long, the CP-725 will disconnect from the line.
If the handset loses its security code, you will also hear an alarm tone. To reset this security code, place the handset in the charging cradle for a few seconds. Pick up the handset and try your call again.
Interference from other appliances may also cause the alarm to sound. To prevent interference, move the charging cradle to another location and fully extend its antenna.
Loading...