Canon MG5120 Getting Started Guide

Canon Inkjet Photo All-In-One
series
Preparation .....................................................P.1
1
Getting Started
Read Me First
Symbols Used in This Document
Prohibited actions.
Instructions including important information.
In this guide, Windows 7 operating system is referred to as Windows 7
• and Windows Vista operating system as Windows Vista.
In this guide, the screens are based on Windows 7 Home Premium
• and Mac OS X v.10.6.x. (Unless noted otherwise, the screens are those of Windows 7.)
Make sure to read this manual before using the machine. Please keep it in hand for future reference.
Install the Ink Tanks ........................................2P.3
Load Paper .....................................................
3
Install the Software .........................................
4
Try Using the Machine ....................................
5
Print Photos from a Memory Card ....................
Try Copying ......................................................
Print Photos from a Computer ..........................
Specications .................................................6P.21
P.7
P.10
P.15
P.16 P.19 P.20
This machine contains both printed manuals and on-screen manuals to be viewed on a computer. The on-screen manuals are included on the Setup CD-ROM and are installed during the software installation.
Prin t e d M a nual s
Gett i n g S t arte d
• (thi s m a n u al)
Describes how to set up and use your machine. Introduces the machine and its functions, the included manuals and application software.
On-S c r e e n Manu a l s
Basi c G u i d e Adva n c e d G uide
Describes basic operations and media, and gives an introduction to other functions available.
Describes various operating procedures to make full use of machine.
Tr o ubles h o o t i ng
Describes troubleshooting tips for problems you may encounter when using the machine.
Model Number: K10358 (MG5120)
For details on opening the on-screen manuals, refer to page 15.
3
4
5
1 2
1
21

Preparation

A
Do not install the machine where an object may fall on it. In addition, do not place any object on the top of the machine. It may fall into the machine when opening covers, resulting in malfunction.
Paper Output Tray (A) automatically opens when printing starts. Do not place anything in front of the Paper Output Tray.
Make sure all the following items are supplied.
1.
Ink tanks (5: BK, M, Y, PGBK, C)
2. Power cord
3. Manuals
4. Setup CD-ROM (containing the drivers, applications and on­screen manuals)
Other documents
5.
A USB cable is necessary to connect the machine with
• your computer.
Remove all orange tape and protective materials from the inside and outside of the machine.
The tape and protective materials may differ in shape and position from what they actually are.
1
3
1
2
When this screen appears, press the OK button, then go to the next step.
4
Use the { or
5 6
} button (E) on the Operation Panel to select the language for
D
B
C
press the OK button.
E
F
the LCD, then
If an unintended language is displayed on the LCD, press the Back button (F) to return to the Language selection screen.
Insert the power cord into the connector on the left side at the back of the machine and
into the wall outlet rmly.
Do NOT connect the USB cable at this stage.
Make sure that the
• Document Cover (B) is closed.
2
1 Preparation
Press the ON button (C), then adjust the LCD (Liquid Crystal Display) (D) to a comfortable viewing angle.
The machine may make some operating noises. This is normal operation.
It takes about 4 seconds for the ON button to work after the power cord is plugged in.
When it is necessary to turn off the machine
Be sure to follow the procedure below.
1. Press the ON button to turn off the machine. . Make sure that the POWER lamp (G) is not lit.
2
Operating noise may continue for up to 35 seconds until the machine turns off.
G
When removing the power plug, make sure that the POWER lamp is not lit before removing the plug. Removing the power plug while the POWER lamp lights up or
ashes may cause drying and
clogging of the Print Head, resulting in poor printing.
The specication of the power
• cord differs for each country or region.
2
1
2
C
C
B
A
D

Install the Ink Tanks

Open the Paper Output Tray (A), then lift the Scanning Unit (Cover) (B) until it stops.
Close the Document Cover (C) and lift it with the Scanning Unit (Cover).
The Print Head Holder (D) moves to the installation position.
If the Print Head Holder does not move, make sure that the machine is turned on. For details, refer to to
on page 2 in "1 Preparation".
Go to the next page.
3
3
4
2 Install the Ink Tanks
4 5
E
1. Remove the orange tape completely.
2. Remove the protective lm
completely.
Handle the ink tanks carefully. Do not drop or apply excessive pressure to them.
Be sure to use the supplied ink tanks.
If the orange tape remains on the L-shape air hole, ink may splash or the machine may not print properly.
If you push the sides of the ink tank with the L-shape air hole blocked, ink may splash.
F
Hold the ink tank with the orange protective cap (E) pointing up while being careful not to block the L-shape air hole (F).
G
H
Hold the ink tank by its sides and slowly twist the orange protective cap 90 degrees horizontally to remove it off.
Do not push the sides of the ink tank.
Do not touch the inside (G) of the orange protective cap or
• the open ink port (H). The ink may stain your hands if you touch them.
7
I
86
Tilt the ink tank, then insert it under the label and against the back end of the slot.
Make sure that the color of the label matches the ink tank.
Install in a well-lit environment.
Do not touch the Print Head Lock Lever (I).
Press the PUSH mark on the ink tank rmly until it clicks.
When the installation is completed properly, the Ink lamp lights red.
Install all the other ink tanks in the same way according to the color order indicated on the label.
Make sure all the Ink lamps light red.
Once you have installed the ink tanks, do not remove them unnecessarily.
If the Print Head Holder moves to the right, close and reopen the Scanning Unit (Cover).
2 Install the Ink Tanks
5
9 10
Lift the Scanning Unit (Cover) slightly, then gently close it.
6
2 Install the Ink Tanks
Make sure that the LCD changes as shown in the illustration and go to the next step.
Load plain paper in the Cassette by referring to "3 Load Paper" on page 7 and press the OK button.
It takes about 4 minutes before the LCD changes.
The machine may make some operating noises when preparing to
• print. This is normal operation.
If an error message is displayed on the LCD, make sure that the ink tanks
• are correctly installed.
The LCD will turn off if the machine is not operated for about 5 minutes.
• To restore the display, press any button except the ON button.
Loading...
+ 16 hidden pages