Canon LC-XWUX6000 User Manual

Table of Contents

MULTIMEDIA PROJECTOR

User’s Manual

Safety Instructions

Before Use

Projecting an Image

Operation

Useful Functions Available During a Presentation

Setting Functions from Menus

Installation and Maintenance

Installation

Connecting to a Network

Maintenance

Appendix

Other Information

Index

ENG

How to Use This Manual

Thank you for purchasing a Canon projector. The WUX6000 Multimedia Projector (hereinafter referred to as “the projector”) is a high-performance projector that is capable of projecting a high-resolution computer screen and high-quality digital image on a large screen.

This Manual

This is the user’s manual for WUX6000 Multimedia Projectors. The “Operation” section describes how to use the projector. The “Installation and Maintenance” section describes the projector installation procedure, network connection procedure, and regular maintenance. Read this manual thoroughly to make the most of your projector. Installation of the projector should be performed by a qualified technician, if possible. Contact the Canon Customer Support Center for further information.

Symbols of Button Operations

The projector can be operated using the buttons on the remote control or on the side of the projector. The remote control allows you to operate all functions of the projector. In this document, the button’s operations are shown as below.

Operation of buttons on side of projector

Remote control button operation

Indicate the buttons to be pressed

Selecting Screen Aspect

Select the correct aspect ratio for the screen which is used.

1 Press the MENU button to display the menu window.

Remote control Projector

Symbols Used in This Manual

Meanings of the symbols used in this manual are as follows.

A precaution about operation or restriction is given here. Indicates supplemental information to note in use.

How to Use This Manual

Please note that enlarging or reducing the size of an image for commercial purposes or public presentation may infringe on the legally protected copyright or the copyright holder of the original material.

About Trademarks

• Ethernet is a registered trademark of Xerox Corporation.

• Microsoft, Windows, Windows Vista, Windows 7, Windows 8 and Aero are

registered trademarks or trademarks of Microsoft Corporation in the United States and / or other countries.

• Mac, Mac OS and Macintosh are trademarks of Apple Inc., registered in the United States and / or other countries.

• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing, LLC.

• PJLink is a registered trademark, or an application has been submitted for trademark, in Japan, the United States and / or other countries or regions.

• AMX is a trademark of AMX Corporation.

• Crestron®, Crestron RoomView®, and Crestron Connected™ are registered

trademarks of Crestron Electronics, Inc.

Projector Highlights

High-Resolution LCOS Projection

Projection at 1920x1200 (WUXGA), thanks to high-resolution reflective liquid crystal on silicon (LCOS) panels.

Lens Shift

Lens shift enables motorized image repositioning up, down, left, or right (P46) for greater freedom in installation.

Motorized Zoom and Focus Adjustment

Efficient setup using motorized zoom and focus adjustment.

Five Lens Units Available

Choose the optimal lens unit for the projection distance or purpose.

Split-Screen Display

Side-by-side projection of two input images from devices connected to the projector. (P67)

USB File Viewer

Project JPEG images stored on a USB flash drive. (P65)

Edge Blending

Blend the overlapping edges of images from multiple projectors to make the overall image more seamless. (P154)

Displaying Test Pattern

Project a range of test patterns, with no image input needed. (P153)

Networked Multi-Projection (NMPJ)

Project images from multiple computers via a network connection. For details on Networked Multi-Projection (NMPJ), refer to the separate user’s manual.

Quick Reference Guide

This Quick Reference Guide will help you find functions that make full use of the projector and are useful for producing an attractive presentation, etc.

Connecting the Projector

Connecting to the Computer (P132 - P134)

Connecting to AV Equipment (P135 - P137)

Projecting an Image

Starting Projection (P38)

Selecting an Input Signal (P39, P40)

Projecting Images from Two Sources at Once (P67)

Adjusting the Image

Adjusting the Image Size and Focus (P44, P45)

Adjusting Keystone Distortion (P54)

Adjusting Aspect Ratio (P48 - P53)

Eliminating Flickers from Computer Screen and Adjusting Positional Shift (P77, P78)

Adjusting Colors and Image Quality

Projecting an Image on a Greenboard (P148)

Selecting an Image Mode Suitable for the Projecting Image (P84)

Making Fine Color Adjustments (P88)

Removing Noise (P90, P91)

Changing the Remote Control

Channel (P102)

Resetting Projector Setting

Canceling the Password (P104)

Initializing the Network Setting (P170)

Restoring Default Menu Settings (P111)

Miscellaneous Functions

Using Power Management (P98)

Turning on the Projector by Connecting the Power Cord (P99)

Disabling the Beep During Operation (P100)

Disabling Buttons (P101)

Hiding Guide Messages (P149)

Setting a Password (P104)

Reducing the Lamp Brightness (P95

Displaying Test Pattern (P153)

Selecting Audio In Terminal (P106)

Combining Images from Multiple Projectors (P154 - P161)

Projecting Images Via Network (For details on Networked Multi-Projection (NMPJ), refer to the separate user's manual.)

)

Producing a Presentation

Temporarily Blacking Out an Image (P62)

Freezing the Picture (P62)

Adjusting the Volume (P63)

Muting the Sound (P63)

Zooming an Image (P64)

Projecting Images on a USB Flash Drive (P65, P66)

How to Use This Manual............... 2

Projector Highlights...................... 4

Quick Reference Guide ................ 5

Safety Instructions...................... 10

Safety Precautions............................... 11

CAUTION ON HANGING FROM THE

CEILING ................................................ 11

AC Power Cord Requirement.............. 14

Federal Communication Commission

Notice .................................................... 15

Precautions for Use ............................. 17

Precautions for Installation................. 18

Precautions on the lamp ..................... 21

Precautions for the batteries of the

remote control...................................... 22

For Safe Use ................................ 23

Open Source Software ............... 25

Before Use..............................27

Supplied Accessories................. 28

Preparing the Remote Control... 29

Part Names .................................. 31

Projector ............................................... 31

Remote control..................................... 32

Side control .......................................... 34

Input Terminal ...................................... 36

Operation

Projecting an Image...............37

Step 1 Turn the Projector On .... 38

Step 2 Select an Input Signal.... 39

Types of Input Signals......................... 39

Selecting an Input Signal .................... 40

Step 3 Adjust the Image ............ 41

Setting the Display Resolution of the

Computer .............................................. 41

Auto PC Adjustment ............................ 43

Focusing, Resizing, or Moving the

Image..................................................... 44

Step 4 Select an Aspect Ratio

(Screen Aspect) Matching the

Screen .......................................... 48

Selecting Screen Aspect ..................... 48

Moving Image with 16:9 D. Image Shift

............................................................... 50

Moving Image with 4:3 D. Image Shift

............................................................... 51

Resetting the Image Shift.................... 52

Select the Aspect ................................. 52

Types of Aspect Ratios ....................... 52

Selecting an Aspect Ratio................... 53

Step 5 Correct the Image

Distortion ..................................... 54

Adjusting Keystone Distortion ........... 54

Step 6 Select the Image Quality

(Image Mode) ...............................57

Image Modes ........................................ 57

Step 7 Set Power-Saving Settings

......................................................59

Step 8 Turn the Projector Off .... 60

Useful Functions Available

During a Presentation ...........61

Useful Presentation Functions ...62

Temporarily Blacking Out an Image... 62

Freezing the Picture............................. 62

Adjusting the Volume .......................... 63

Muting the Sound................................. 63

Zooming Part of an Image................... 64

Projecting Images on a USB Flash

Drive ............................................. 65

Split-Screen Display....................67

Setting Functions from Menus

.................................................71

Using Menus ................................72

Menu Configuration ............................. 72

Basic Menu Operations ....................... 73

Setting Display Status (Input

Settings).......................................75

Selecting the Aspect............................ 75

Setup Using Auto PC........................... 76

Table of Contents

Selecting an Input Signal

(Analog PC Input)................................. 76

Adjusting the Input Signal

(Total dots)............................................ 77

Adjusting the Input Signal

(Tracking).............................................. 77

Adjusting the Input Signal

(Horizontal / Vertical position) ............ 78

Adjusting the Input Signal

(Horizontal / Vertical pixels) ................ 78

Adjusting HDMI Input Level ................ 79

Setting the HDMI Color Format........... 79

Specifying HDMI Overscan ................. 80

Specifying Progressive Processing ... 80

Specifying the Slideshow Interval...... 81

Specifying Split-Screen Display ......... 82

Adjusting Image Quality (Image

Adjustment) ................................. 83

Specifying Image Priority in Split-

Screen Mode......................................... 83

Specifying the Image Mode................. 84

Creating/Saving a User Profile ........... 85

Adjusting Brightness........................... 86

Adjusting Contrast............................... 86

Adjusting Sharpness........................... 87

Correcting Gamma............................... 87

Adjusting Colors .................................. 88

Adjusting to the Ambient Light

(Ambient Light) .................................... 89

Reducing Image Noise

(Random noise reduction) .................. 90

Reducing Image Noise

(MPEG noise reduction) ...................... 90

Reducing Image Noise

(Mosquito noise reduction)................. 91

Dynamic Gamma Adjustment............. 91

Correcting Memory Color.................... 92

Fine-Tuning Colors

(6-axis Color Adjustment) ................... 92

Fine-Tuning Gamma ............................ 93

Specifying Lamp Control .................... 94

Specifying the Lamp Mode ................. 95

Resetting Image Adjustment Settings

............................................................... 95

Customizing System Operation

(System Settings)........................ 96

Registering User Logos ...................... 96

Positioning User Logos....................... 96

No Signal Screen ................................. 97

Screen When Blank ............................. 97

Selecting a Logo at Startup ................ 98

Specifying Power Management Mode

............................................................... 98

Specifying Power Management Duration

............................................................... 99

Specifying Direct Power-On................ 99

Specifying Silence or Operating Tones

............................................................. 100

Specifying Key Repeat Operation .... 100

Locking Projector or Remote Buttons

............................................................. 101

Assigning a Channel for Remote Control

............................................................. 102

Reducing Motion Blur........................ 103

Selecting a Display Language .......... 103

Requiring a Password for Operation

............................................................. 104

Setting a Password............................ 105

Using the Remote Control [Fn] Button

............................................................. 105

Selecting Audio Input ........................ 106

Restoring Original Gamma Settings

............................................................. 107

Specifying HDMI Input....................... 108

Resetting the Lamp Counter............. 108

Resetting the Air Filter Counter........ 110

Updating the Firmware ...................... 110

Resetting to the Default Setting ....... 111

Checking Projector Information

....................................................112

Installation and Maintenance

Installation............................113

Before Installation.....................114

Precautions When Carrying/

Shipping the Projector ...................... 114

Precautions for Installation............... 114

Installation Procedure...............118

Setting Up the Projector.................... 118

Installing / Removing the Lens Unit

............................................................. 120

Table of Contents

Relationship Between Image Size and

Projecting Distance ........................... 125

Lens Shift Function ........................... 129

Connection Procedure ............. 131

Connectable Equipment and Input

Terminals ............................................ 131

Connecting a Computer .................... 132

Connecting AV Equipment................ 135

Plugging the Projector In .................. 138

Starting Projection.................... 139

Starting and Stopping Projection ..... 139

Changing Notebook Computer Screen

Output ................................................. 140

Installation-Related Menu

Settings...................................... 141

Locking Installation Settings............ 141

Flipping Image Display...................... 141

Specifying the Screen Aspect .......... 142

Adjusting the Size of Projected Images

............................................................. 143

Specifying Keystone Correction ...... 144

Specifying Digital Image Shift .......... 145

Specifying Micro Digital Image Shift

............................................................. 145

Adjusting Image Registration........... 146

Specifying the Fan Mode................... 146

Specifying Vertical Projection .......... 147

Saving and Restoring Lens Positions

............................................................. 147

Screen Color Adjustment.................. 148

Specifying a Menu Position .............. 149

Showing/Hiding the Guide Screen ... 149

Showing/Hiding Input Status............ 150

Showing/Hiding Overheat Warnings

............................................................. 150

Specifying the Menu Display Time ... 151

Showing/Hiding Lamp Replacement

Warnings............................................. 151

Showing/Hiding Filter Cleaning

Warnings............................................. 152

Showing/Hiding Split-Screen ID ....... 152

Displaying Test Patterns................... 153

Projecting from Multiple Projectors at

Once (Edge Blending) ....................... 154

Connecting to a Network ....163

Network Connection Overview

....................................................164

Connection Methods ......................... 164

Completing Projector Settings

....................................................165

Locking/Unlocking Network Settings

............................................................. 165

Specifying the Network Password ... 166

Registering a Network Password ..... 167

Specifying Standby Power

Consumption...................................... 167

Specifying the Network Function ..... 168

Viewing the IP Address, Gateway

Address, and MAC Address.............. 168

Specifying DHCP................................ 169

Specifying TCP/IP Settings ............... 169

Initializing Network Settings ............. 170

Specifying PJLink Settings............... 170

Specifying AMX Device Discovery ... 171

Specifying Crestron RoomView ....... 172

Completing Computer Settings

....................................................173

Specifying an IP Address.................. 173

Setting Up the Network ..................... 177

Control via the Web Screen .............. 191

Maintenance.........................193

Cleaning the Projector and the Air

Filter............................................194

Cleaning the Air Filter........................ 194

Replacing the Air Filter.............196

Replacing the Lamp ..................197

Replacement Lamp ............................ 198

Replacing the Lamp........................... 199

Appendix

Appendix ..............................201

Troubleshooting........................202

LED Indicator Meanings .................... 202

Symptoms and Solutions.................. 203

Relationship between Aspect and

Screen Aspect ........................... 209

Displayed Test Patterns ........... 213

Supported Signal Types........... 214

Product Specifications ............. 216

Index........................................... 224

Option ........................................ 227

Menu Configuration .................. 228

Table of Contents

Safety Instructions

Before installing and operating the projector, read this manual thoroughly. This projector provides many convenient features and functions. Operating the projector properly enables you to manage those features and maintain it in good condition for many years to come. Improper operation may result in not only shortening the product life, but also malfunctions, fire hazards, or other accidents. If your projector does not seem to be operating properly, read this manual again, check operations and cable connections, and try the solutions in the “Troubleshooting” section in the back of this manual. If the problem still persists, contact the Canon Customer Support Center.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT

REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE EXCEPT LAMP REPLACEMENT. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT.

THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS FOR THIS UNIT IN THE OWNER’S MANUAL.

CAUTION

Not for use in a computer room as defined in the Standard for the Protection of Electronic Computer / Data Processing Equipment, ANSI / NFPA 75.

Safety Instructions

Safety Precautions

WARNING:

• THIS APPARATUS MUST BE GROUNDED.

• TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

• This projector produces intense light from the projection lens. Do not stare

directly into the lens, otherwise eye damage could result. Be especially careful that children do not stare directly into the beam.

• Install the projector in a proper position. Otherwise it may result in a fire hazard.

• Allowing the proper amount of space on the top, sides, and rear of the projector

cabinet is critical for proper air circulation and cooling of the unit. The diagrams shown here indicates the minimum space required. If the projector is to be built into a compartment or similarly enclosed, these minimum distances must be maintained.

SIDE and TOP REAR

50 cm (1.6')

Safety Instructions

50 cm

(1.6')

• Do not cover the ventilation slots on the projector. Heat build-up can reduce the service life of your projector, and can also be dangerous.

• If the projector is unused for an extended time, unplug the projector from the power outlet.

• Do not project the same image for a long time.

An afterimage may remain on the LCD panels due to the characteristics of the panels of the projector.

50 cm

(1.6')

50 cm

(1.6')

CAUTION ON HANGING FROM THE CEILING

When hanging the projector from the ceiling, clean the air intake vents and top of the projector periodically with a vacuum cleaner. If you leave the projector unclean for a long time, the cooling fans can be clogged with dust, and it may cause a breakdown or a disaster.

DO NOT SET THE PROJECTOR IN GREASY, WET, OR SMOKY CONDITIONS SUCH AS IN A KITCHEN TO PREVENT A BREAKDOWN OR A DISASTER. IF THE PROJECTOR COMES IN CONTACT WITH OIL OR CHEMICALS, IT MAY BECOME DETERIORATED.

Safety Instructions

■ READ AND KEEP THIS OWNER’S MANUAL FOR LATER

USE.

All the safety and operating instructions should be read before beginning to operate the product.

Read all of the instructions given here and retain them for later use. Unplug this projector from the AC power supply before cleaning. Do not use liquid or aerosol cleaners on the projector. Use a damp cloth for cleaning.

Follow all warnings and instructions marked on the projector.

For added protection of the projector during a lightning storm, or when it is left unattended or unused for long periods of time, unplug it from the wall outlet. This will prevent damage due to lightning and power surges.

Do not expose this unit to rain or use near water... for example, in a wet basement, near a swimming pool, etc...

Do not use attachments not recommended by the manufacturer as they may result in hazards.

Do not place this projector on an unstable cart, stand, or table. The projector may fall, causing serious injury to a child or adult, and serious damage to the projector. Use only with a cart or stand recommended by the manufacturer, or sold with the projector. Wall or shelf mounting should be carried out in accordance with the manufacturer’s directions, and should use a mounting kit approved by the manufacturers. An appliance and cart combination should be moved with care. Sudden stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

Slots and openings in the rear and front of the cabinet are provided for ventilation, to insure reliable operation of the equipment and to protect it from overheating.

The openings should never be covered with cloth or other materials, and the bottom opening should not be blocked by placing the projector on a bed, sofa, rug, or other similar surface. This projector should never be placed near or over a radiator or heat register.

This projector should not be placed in a built-in installation such as a book case unless proper ventilation is provided.

Safety Instructions

Never push objects of any kind into this projector through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind onto the projector.

Do not install the projector near the ventilation duct of air-conditioning equipment.

This projector should be operated using only the type of power source indicated on the marking label. If you are not sure of the type of power supplied, contact the Canon Customer Support Center or local power company.

Do not overload wall outlets and extension cords as this can result in fire or electric shock. Do not allow anything to rest on the power cord. Do not locate this projector where the cord may be damaged by people walking on it.

Do not attempt to service this projector yourself as opening or removing covers may expose you to dangerous voltages or other hazards. Refer all servicing to qualified service personnel.

Unplug this projector from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the power cord or plug is damaged or frayed. b. If liquid has been spilled into the projector. c. If the projector has been exposed to rain or water. d. If the projector does not operate normally after following the operating

instructions. Adjust only those controls that are covered in the operating instructions as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the projector

to normal operating condition. e. If the projector has been dropped or the cabinet has been damaged. f. When the projector exhibits a distinct change in performance-this indicates a

need for servicing.

Safety Instructions

When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer that have the same characteristics as the original parts. Unauthorized substitutions may result in fire, electric shock, or injury.

Upon completion of any service or repairs to this projector, ask the service technician to perform routine safety checks to determine that the projector is in safe operating condition.

Safety Instructions

AC Power Cord Requirement

The AC Power Cord supplied with this projector meets the requirements for use in the country you purchased it.

AC Power Cord for the United States and Canada:

The AC Power Cord used in the United States and Canada is listed by the Underwriters Laboratories (UL) and certified by the Canadian Standard Association (CSA). The AC Power Cord has a grounding-type AC line plug. This is a safety feature to ensure the plug fits into the power outlet. Do not try to tamper with this safety feature. Should you be unable to insert the plug into the outlet, contact your electrician.

THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.

NOTE FOR CUSTOMERS IN THE US

LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE OR FEDERAL LAWS.

Ground

Only for European Union and EEA (Norway, Iceland and Liechtenstein)

These symbols indicate that this product is not to be disposed of with your household waste, according to the WEEE Directive (2012/ 19/EU), the Battery Directive (2006/66/EC) and/or national legislation implementing those Directives. If a chemical symbol is printed beneath the symbol shown above, in accordance with the Battery Directive, this indicates that a heavy metal (Hg = Mercury, Cd = Cadmium, Pb = Lead) is present in this battery or accumulator at a concentration above an applicable threshold specified in the Battery Directive. This product should be handed over to a designated collection point, e.g., on an authorized one-for-one basis when you buy a new similar product or to an authorized collection site for recycling waste electrical and electronic equipment (EEE) and batteries and accumulators. Improper handling of this type of waste could have a possible impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. Your cooperation in the correct disposal of this product will contribute to the effective usage of natural resources. For more information about the recycling of this product, please contact your local city office, waste authority, approved scheme or your household waste disposal service or visit www.canon-europe.com/weee

, or www.canon-europe.com/battery.

Safety Instructions

Federal Communication Commission Notice

Multimedia Projector, Model: WUX6000 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that

may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Safety Instructions

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio / TV technician for help.

The cable with a ferrite core provided with the projector must be used with this equipment in order to comply with Class B limits in Subpart B of Part 15 of the FCC rules. Use of a shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules. Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment. Canon U.S.A. Inc. One Canon Park, Melville, New York 11747, U.S.A. Tel No. (631) 330-5000

Safety Instructions

Safety Symbols in this Manual

This section describes the safety symbols used in this manual. Important projector safety information is identified by the following symbols. Always observe the safety information by these symbols.

Denotes the risk of death or serious injury from improper handling if the information is not observed. To ensure safe use, always observe this information.

Denotes the risk of injury from improper handling if the information is not observed. To ensure safe use, always observe this information.

Denotes prohibited actions.

Denotes required actions or information that must be observed.

Safety Instructions

Precautions for Use

As this section contains important safety-related information, be sure to read the following carefully beforehand in order to use your projector correctly and safely.

If the following situations occur, turn the power off, remove the power plug from the power outlet and contact the Canon Customer Support Center. Failure to do so could cause a fire or result in an electric shock.

• If smoke is emitted

• If an unusual smell or noise is emitted

• If a loud noise is heard and the lamp turns off

• If water or other liquid has entered the projector

• If metal or any other foreign material has entered the projector

• If the projector is knocked over or dropped and the cabinet is damaged

Pay attention to the following points for handling the power cord. Failure to do so may cause a fire, electric shock or personal injury.

Safety Instructions

• Do not place any objects on the power cord and do not allow it to become trapped under the projector. The power cord may be damaged.

• Do not cover the power cord with a carpet.

• Do not excessively bend, twist, pull or make modifications to the power cord.

• Keep the power cord away from heaters and other sources of heat.

• Do not use the power cord when it is bent finely, coiled or bundled.

• Do not use a damaged power cord. If your power cord is damaged, contact

the Canon Customer Support Center.

• The power cord included with this projector is for use exclusively with this product. Do not use this cord for other products.

• Be sure to connect the ground wire of the power cord to ground. Failure to do so could result in an electric shock.

• Be sure to connect the ground wire before connecting the power plug to the outlet. Also when you disconnect the ground wire, be sure to unplug the power plug from the outlet beforehand.

Safety Instructions

Pay attention to the following points regarding the power source, power plug and handling of the connector. Failure to do so may cause a fire, electric shock or personal injury.

•

Do not use any power source with a voltage other than the voltage indicated (AC 100–240 V).

• Do not pull the power cord and be sure to hold the power plug or connector when removing. The cord could be damaged as a result.

• Do not insert any metal objects into the contact parts of the power plug or connector.

• Remove the power plug from the outlet before performing cleaning or maintenance of the projector.

• Do not remove the power plug or connector with wet hands.

• Insert the power plug and connector securely up to the base. Additionally, do

not use a damaged power plug or an outlet that is loose.

• If using an extension cord attached to the outlet, make sure that the total electric power consumption of connected devices does not exceed the rated capacity.

• Periodically inspect the power plug and outlet and remove any dust or dirt from between the plug and the outlet.

Precautions for Installation

Pay attention to the following points regarding installation and handling of the projector. Failure to do so may cause a fire, electric shock or personal injury.

• Do not use the projector in a bathroom or shower room.

• Do not use the projector in rain or snow, by the sea, or in close proximity to a

body of water.

• Do not place containers containing a liquid on top of the projector.

• Do not place the projector in any location where it will be exposed to oily

smoke or steam, such as a kitchen work surface or table etc.

• Do not touch the projector itself, the power cord, or the cable if lightening strikes.

Safety Instructions

Pay attention to the following points regarding installation and handling of the projector. Failure to do so may cause a fire, electric shock or personal injury.

• Do not move the projector until you have switched off the power, removed the power plug from the power outlet and unplugged any other cables.

• Before you attach or replace a lens unit, be sure to unplug the power plug of the projector from the power outlet. Failure to unplug the power cord could result in an electric shock or personal injury.

• Do not remove the cabinet from the projector or disassemble it. The interior of the projector contains high-voltage components as well as parts that are hot. These could cause an electric shock or burn. If inspection, maintenance or repair is required, contact the Canon Customer Support Center.

• Do not disassemble or modify the projector (including consumable parts) or the remote control.

• Do not look directly into the exhaust vents during use.

• Do not insert any object into vents in the projector, such as the air intake vent

or exhaust vents.

• Do not place a pressurized can in front of the exhaust vents. The pressure of the contents of the can may increase due to heat from the exhaust vents and this could result in an explosion.

• As strong light beams are emitted while the projector is in use, do not look directly into the projector lens. Doing so could cause an eye injury. Pay particular attention to prevent small children from doing so.

• When giving a presentation in front of the projector while it is projecting an image, conduct your presentation from a position where your shadow will not be cast on the screen and where you do not feel blinded by light from the projector.

• When setting the projector on a high surface for projection, be sure the surface is flat and stable. Failure to do so could result in the projector falling down and causing an accident or personal injury.

Safety Instructions

Pay attention to the following points regarding installation and handling of the projector.

• If the projector will not be used for a long period of time, be sure to remove the power plug from the power outlet to ensure safety. Failure to do so could cause a fire.

• The temperature of the cabinet around and above the exhaust vents can become hot during projector operation. Touching these areas during operation could cause burns to the hands. Do not touch these areas. Doing so may cause burns. Pay particular attention in preventing young children from touching these parts. Additionally, do not place any metal objects on these areas. Due to the heat from the projector, doing so could cause an accident or personal injury.

Pay attention to the following points regarding installation and handling of the projector.

• Do not place any heavy objects on top of the projector or sit / stand on it. Pay particular attention to prevent small children from doing so. The projector may be knocked over and this could result in damage or a personal injury.

• Do not place the projector on an unstable or slanted surface. Doing so may cause the projector to fall or be knocked over and could result in a personal injury.

• Do not place any objects in front of the lens while the projector is operating. Doing so could cause a fire.

• The projector is provided with a lens shift function to move the lens up, down, left, and right using the motor. Do not touch the lens while it is moving. Touching the lens when it is moving may result in personal injury.

• When cleaning off dust or dirt from the projector lens etc., do not use any kind of spray that is flammable. As the temperature of the lamp inside the projector is high, it could ignite, causing a fire.

• Before replacing the lens unit, wait at least one hour after the projector is turned off to allow the projector to cool thoroughly. Failure to do so could result in a burn or injury.

• If the projector is used for a long period of time, dust could accumulate inside the projector. This could cause a fire or malfunction. It is recommended that periodic maintenance of the projector be performed. For details of maintenance costs, contact the Canon Customer Support Center.

• When hanging the projector from a ceiling, put the projector down on the floor or a workbench before attaching or replacing the lens unit. Failure to do so could result in parts falling off the projector and may cause an accident or personal injury.

Safety Instructions

Precautions on the lamp

This projector uses a high-pressure mercury lamp, which must be handled carefully and correctly as describeded below. The mercury lamp has the following characteristics.

• Impact, abrasion, or use after the lamp’s useful life has expired may damage lamps (which may be accompanied by a loud noise) or cause them to burn out.

• Useful life of lamps varies widely from lamp to lamp and depending on the environment of use. Lamps are not guaranteed to last for the same amount of time, and some lamps may fail sooner than others.

• The lamp will gradually become darker over time.

When replacing the lamp, or when the lamp is damaged, pay attention to the following points. Failure to do so could result in an electric shock or personal injury.

•

Be sure to remove the power plug from the power outlet before replacing the lamp.

• When the lamp is damaged, shards of glass may be scattered inside the projector. Contact the Canon Customer Support Center for cleaning and inspection of the projector interior and lamp replacement.

• Precautions when replacing lamps that stop working If the illumination suddenly stops when the projector is in use or after you turn it on, the lamp may be broken. In this case, never attempt to replace the lamp by yourself. Always request service from the Canon Customer Support Center. Additionally, with ceiling-mounted projectors, the lamp may fall out when you open the lamp cover or while you are attempting to replace it. During replacement, stand to the side of the lamp cover, not directly under it. If the lamp breaks and any glass shards or other pieces get in your eyes or mouth, consult a doctor immediately.

• If the lamp is damaged, gas inside the lamp (containing mercury) and dust may be emitted from the exhaust vents. If this happens, immediately open the windows and doors to provide ventilation to the room. If you inhale any gas emitted from the lamp or it has come into contact with your eyes or mouth, consult a doctor immediately.

Safety Instructions

When handling the lamp, pay attention to the following points.

• Be sure not to handle the lamp immediately after it has been used. Be sure to switch off the power and wait for approximately 1 hour for the lamp and the projector to cool down sufficiently. Failure to do so could result in a burn or personal injury due to heat from the lamp or projector.

• When an instruction to replace the lamp has been displayed (LAMP Indicator Displays (P35)), the possibility of the lamp breaking will increase. Replace the lamp with a new one as soon as possible.

• When disposing of a used mercury lamp, dispose of it in the same way as a fluorescent lamp and in accordance with the local regulations where you live.

Precautions for the batteries of the remote control

Pay attention to the following points regarding handling of batteries. Failing to do so could result in a fire or personal injury.

•

Do not heat, short circuit or disassemble the batteries, or place them in a fire.

• Do not attempt to recharge the batteries that are included with the remote control.

• Remove the batteries when they are flat or when the remote control will not be used for a long period of time.

• When replacing the batteries, replace both at the same time. Also, do not use two batteries of a different type at the same time.

• Insert the batteries with the + and - terminals in the correct directions.

• If any liquid from inside the batteries leaks out and contacts your skin, be

sure to wash the liquid off thoroughly.

For Safe Use

Pay attention to the following points when carrying or transporting the projector.

• This projector is a precision instrument. Do not knock it over or subject it to impacts. Doing so may cause a malfunction.

• When carrying or holding up the projector after attaching the lens unit, be sure not to hold the lens. Doing so may cause damage to the lens unit.

• Do not reuse any packaging or shock-absorbent materials that were supplied with the projector at the time of purchase for transporting or shipping the projector. Protection of the projector cannot be guaranteed if used packaging or shock-absorbent materials are reused. Fragments from shock-absorbent material may also enter the interior of the projector which could cause a malfunction.

• If transportation is necessary, the lens unit should be removed before transporting the projector. If the projector is subjected to excessive impacts during transportation, the lens unit may be damaged. Removal and installation of the lens unit should not be performed by the user. Be sure to have the procedure performed by a qualified technician or contact the Canon Customer Support Center.

• Disconnect the cables connected to the projector. Carrying the projector with the cables attached may cause an accident.

• Retract the adjustable feet.

For Safe Use

Pay attention to the following points when installing or using the projector.

• Do not touch the lens with bare hands. Doing so may result in deterioration of image quality.

• If the projector is suddenly moved from a location where the temperature is low to a location where the temperature is high, or if the temperature in the location where the projector is installed increases suddenly, moisture in the air could cause condensation to form on the projector lens or mirror. This may cause a blurred image. Wait until the condensation has evaporated for the image projected to return to normal.

• Do not install the projector in a location where the temperature is high or low. Doing so may cause a malfunction. The temperature range for operation and storage are as follows.

Operating temperature: 0°C (32°F) to 40°C (104°F) Humidity level: up to 85% Storage temperature: -10°C (14°F) to 60°C (140°F)

• Do not place any objects on top of the projector that may change shape or color due to heat.

• When using the projector at altitudes greater than 2,300 m (7,545.8'), or for projecting upward / downward:

When using the projector at altitudes greater than 2,300 m (7,545.8'), or for upward projection or downward projection, it is necessary to change the settings of the projector. Specifically, adjust [Fan mode] (P146) or [Vertical projection] (P147) in the [Install settings] menu.

• Do not install the projector near high-voltage electrical power lines or an electrical power source.

• Do not use the projector on a soft surface such as carpet or sponge mat, etc. Doing so could cause heat to build up inside the projector and this could result in a malfunction.

• Do not block the air intake or exhaust vents of the cooling fan. If the air intake or exhaust vent is blocked, heat cannot be released from inside the projector, which may shorten the useful life of the lamp or cause malfunction.

• Installing the projector in the wrong direction may cause a malfunction or accident. Ensure that the left or right side of the projector is not tipped up more than 10°.

• Be sure to install the projector in a location where the air intake and exhaust vents are separated from the wall by more than 50 cm (1.6'). Failure to do so could cause a malfunction.

• Do not install the projector in a location that is damp, or where there is a lot of dust, oily smoke or tobacco smoke. Doing so could cause contamination of optical components such as the lens and the mirror and may result in deterioration of image quality.

Open Source Software

The product contains Open Source Software modules. For details, see “ThirdPartySoftware.pdf” (Third-Party Software License) in the OpenSourceSoftware folder in the LICENSE folder on the Setup CD-ROM. Each module’s license conditions are also available in the same folder.

■ Software under the GNU General Public License Version 2

Contained programs are free software; you can redistribute them and/or modify them under the terms of the GNU General Public License attached to each copy of the program.

Each program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. Please see “NO WARRANTY” and “NO SUPPORT” stated below. For more detail, please see full text of the GNU General Public License.

NO WARRANTY

BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.

Open Source Software

IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

NO SUPPORT

Canon Inc., and all its subsidiaries or its dealers do not make any support service regarding the source code. Canon Inc., and all its subsidiaries or its dealers shall not respond to any questions or enquiries, from you or any other customers, regarding the source code.

Table of Contents

Safety Instructions

Before Use

Projecting an Image

Operation

Useful Functions Available During a Presentation

Setting Functions from Menus

Installation and Maintenance

Installation

Connecting to a Network

Maintenance

Appendix

Other Information

Index

Supplied Accessories

Check that the following accessories have been supplied with the projector.

• Remote control • Batteries for the remote control

(AAA size x2)

(part No.: RS-RC04)

Optional remote controls are also available (RS-RC05). However, some buttons are not supported with this projector. The RS-RC05 can also be used as a wired remote. (P30)

• Computer cable (1.8 m / 5.9') (mini D-sub 15-pin / mini D-sub 15-pin)

• CD-ROM User’s Manual / Supplement NMPJ Ver. 1.1 User’s Manual

• Power cord (1.8 m / 5.9')

For Continental Europe

For the U.S.A. and Canada

• Warranty Card

• Important Information

Preparing the Remote Control

■ Installing Remote Control Batteries

1 Open the battery

compartment lid.

Slide the lid while pressing it down.

• If buttons on the remote control are inoperative when you attempt to operate the projector, replace the batteries with new ones.

• Do not drop the remote control or subject it to impact.

• Do not spill any liquids on the remote control. Doing so could damage it.

Pay attention to the following points when handling the batteries. Failing to do so could result in a fire or personal injury.

• Do not heat, short circuit or disassemble the batteries, or place them in a fire.

• Do not attempt to recharge the batteries that are included with the remote control.

2 Insert batteries.

Insert 2 new AAA batteries in the compartment with the + and – poles positioned correctly.

3 Close the

compartment lid.

Slide the lid until you hear a click to securely close it.

Before Use

• Remove the batteries when they are flat or when the remote control will not be used for a long period of time.

• When replacing the batteries, replace both at the same time. Also, do not use two batteries of a different type at the same time.

• Insert the batteries with the + and - terminals in the correct directions.

• If any liquid from inside the batteries leaks out and contacts your skin, be sure to wash the liquid off thoroughly.

Preparing the Remote Control

■ Remote Control Operating Range

The remote control is an infrared type. Point it at the infrared remote receiver on the front or rear of the projector to operate it.

25°

8 m (26.3')

25°

8 m (26.3')

25°

• Use the remote control within an angle of 25° in any direction from directly in front of the infrared remote receiver.

• The remote control may be inoperative if there is an obstacle between the remote control and the projector or the infrared remote receiver on the projector is exposed to direct sunlight or strong light of lighting equipment.

• When you use 2 or more projectors at the same time, you can change the channel settings to prevent the 2 remote controls from interfering with each other. (P102)

■ Using an Optional Wired Remote (RS-RC05)

To use a wired remote control with the projector, use the RS-RC05, sold separately. Use a cable with a ø3.5 mm stereo mini jack (not included).

Terminal for wired

remote control

ø3.5 mm stereo mini jack

cable (not included)

• Infrared operations cannot be performed if a cable is connected to the projector or the remote control.

• Use a cable with a ø3.5 mm stereo mini jack (not included) with a length of 30 m (98.4') or less.

+ 206 hidden pages