Canon LC-XWUX5800Z, LC-XWUX6600Z, LC-XWUX7000Z User Manual

MULTIMEDIA PROJECTOR

User’s Manual

Safety Instructions

Before Use

Basic Guide

Projection Procedure

Convenient Projection Features

Installation Procedure

Installation Guide

Connection Procedure

Adjusting the Image

Special Arrangements

Using Menus

Menu Guide

Menu Configuration

Menu Description

Maintenance

Product Specifications

Troubleshooting

ENG

How to Use This Manual

LENS button

FOCUS button

ZOOM button

Remote control

Projector

Symbols Used in This Manual

Sections labeled with these symbols give the following kinds of information.

Indicates precautions and information to note when using the projector.

Symbols of Button Operations

The projector can be operated using the buttons on the remote control or on the side of the projector. The remote control allows you to operate all functions of the projector. In this document, the button’s operations are shown as below.

Remote control button operation

Operation of buttons on side of projector

Indicate the buttons to be pressed

Thank you for purchasing a Canon projector. The WUX7000Z/WUX6600Z/WUX5800Z Multimedia Projector is a highperformance laser projector capable of projecting high-resolution computer screens and high-quality digital images on a large screen.

This Manual

This is the user’s manual for WUX7000Z/WUX6600Z/WUX5800Z Multimedia Projector (hereafter, “projector”). The “Basic Guide” describes basic steps before projection and introduces features that are convenient in presentations and other situations. The “Installation Guide” covers how to install the projector and join a network, and the “Menu Guide” explains setting menus and how to use them. Read this manual thoroughly to make the most of your projector. We recommend requesting installation by a qualified technician or the Canon Customer Support Center.

Focusing / Resizing the Image

Press the ZOOM button on the remote control to adjust the image size, and press the FOCUS button to adjust the focus. You can also press the LENS button on the projector once to adjust focus and twice to adjust image size.

How to Use This Manual............... 2

Projector Highlights...................... 5

Safety Instructions........................ 7

Safety Symbols in this Manual ........... 13

Precautions for Use ............................. 14

Power Supply ....................................... 14

Installation and Use ............................. 16

Laser Light Source .............................. 18

Remote Control Batteries.................... 21

Handling................................................ 21

For Safe Use ................................ 23

Carrying and Installation..................... 23

Before Installation....................... 25

Precautions When Carrying / Shipping

the Projector......................................... 25

Precautions for Installation................. 25

Wireless LAN (Wi-Fi)............................ 30

Open Source Software ............... 31

Before Use ................................... 32

Included Accessories .......................... 32

Projector Part Names and

Functions.............................................. 33

Remote Control .................................... 38

Basic Guide ............................43

Projection Procedure.................. 44

Step 1 Connect Other Equipment....... 45

Step 2 Turn the Projector On .............. 46

Step 3 Select an Input Signal.............. 47

Step 4 Adjust the Image ...................... 48

Step 5 Select the Image Quality

(Image Mode)........................................ 49

Turn the Projector Off.......................... 51

Convenient Projection

Features ....................................... 52

Convenient Features ........................... 52

Projecting Images on a USB Flash

Drive ...................................................... 56

Projecting Two Images Side by

Side ....................................................... 60

Installation Guide...................62

Installation Procedure.................63

Relationship Between Projecting

Distance and Image Size ..................... 63

Installing / Removing the Lens Unit ... 67

Installation ............................................ 70

Adjusting Peripheral Focus ................ 74

Connection Procedure................78

Connecting Other Equipment............. 78

Connecting to a Network..................... 83

Controlling the Projector from a

Computer .............................................. 97

Adjusting the Image ....................99

Filling the Screen ................................. 99

Adjusting Keystone Distortion ......... 103

Adjustment Using a Test Pattern ..... 107

Special Arrangements ..............108

Projecting from Multiple Projectors at

Once (Edge Blending) ....................... 108

Using PC-Free Multi Projection ........ 114

Menu Guide ..........................118

Using Menus ..............................119

Menu Configuration ..................122

Menu Description ......................130

Input settings ..................................... 130

Image adjustment .............................. 139

Install settings.................................... 149

System settings ................................. 161

Network settings ................................ 182

Checking Projector Information ....... 197

Projector Web Screen Menu.....198

Maintenance / Product Specifications /

Troubleshooting ..................216

Maintenance...............................217

Cleaning the Projector....................... 217

Replacing the Air Filter...................... 217

Table of Contents

Product Specifications ............. 219

Troubleshooting........................ 229

LED Indicator Details......................... 229

Symptoms and Solutions.................. 230

Index........................................... 237

Option ........................................ 239

Projector Highlights

Bright Yet Compact, With a Laser Light Source

A bright projector that is also compact, at 480 x 545 x 196 mm (18.9 x 21.5 x 7.7 in., W x D x H). Features a laser light source that lasts longer than traditional mercury lamps.

Peripheral Focus Adjustment

Image focus can be adjusted on the edges of the screen, enabling use in dome projection.

HDBaseT Input

The projector supports HDBaseT, a next-generation connectivity standard. HDBaseT offers a convenient connection for carrying high-quality video and audio signals equivalent to HDMI across distances up to 100 m (328.1') over a single LAN cable.

Lens Shift

Lens shift enables motorized image repositioning up, down, left, or right for greater freedom in installation.

Motorized Zoom and Focus Adjustment

Efficient setup using motorized zoom and focus adjustment.

Full Range of Lens Units Available

Choose the optimal lens unit for the projection distance or purpose.

Superior Video Viewing Experience

Refinements in motion blur reduction make video projection more enjoyable to watch.

Scheduling

Automate projector tasks according to your schedules. Turn the projector on or off, switch input signals, and more.

Edge Blending

Blend the overlapping edges of images from multiple projectors to make the overall image more seamless.

Networked Multi-Projection (NMPJ)

Project images from multiple computers via a network connection.

Projector Highlights

Wi-Fi Connectivity

In addition to wired LAN connectivity, the projector also supports Wi-Fi. In Projector Access Point (PJ AP) mode, the projector can be connected to up to five computers without using a wireless access point.

Canon Service Tool for PJ (Canon ST)

An iOS app for easy remote control and status management of projectors over WiFi. Connect to a projector used as an access point (P84), or connect via an existing access point (P84). Note that a password is required when using Canon ST (P198).

Safety Instructions

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

Before installing and operating the projector, read this manual thoroughly. This projector provides many convenient features and functions. Operating the projector properly enables you to manage those features and maintain it in good condition for many years to come. Improper operation may result in not only shortening the product life, but also malfunctions, fire hazards, or other accidents. If your projector does not seem to be operating properly, read this manual again, check operations and cable connections, and try the solutions in the “Troubleshooting” section in the back of this manual. If the problem still persists, contact the Canon Customer Support Center.

THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT.

THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS FOR THIS UNIT IN THE OWNER’S MANUAL.

Safety Instructions

CAUTION Not for use in a computer room as defined in the Standard for the Protection of Electronic Computer / Data Processing Equipment, ANSI / NFPA 75.

Safety Instructions

Safety Precautions

WARNING:

• THIS APPARATUS MUST BE GROUNDED.

• TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

• This projector produces intense light from the projection lens. Do not stare

directly into the lens, otherwise eye damage could result. Be especially careful that children do not stare directly into the beam.

• Install the projector in a proper position. Otherwise it may result in a fire hazard.

• Do not cover the ventilation slots on the projector. Heat build-up can reduce the

service life of your projector, and can also be dangerous.

• If the projector is unused for an extended time, unplug the projector from the power outlet.

• Do not project the same image for a long time.

An afterimage may remain on the LCD panels due to the characteristics of the panels of the projector.

CAUTION ON HANGING FROM THE CEILING

When hanging the projector from the ceiling, clean the air intake vents and top of the projector periodically with a vacuum cleaner. If you leave the projector unclean for a long time, the cooling fans can be clogged with dust, and it may cause a breakdown or a disaster.

DO NOT SET THE PROJECTOR IN GREASY, WET, OR SMOKY CONDITIONS SUCH AS IN A KITCHEN TO PREVENT A BREAKDOWN OR A DISASTER. IF THE PROJECTOR COMES IN CONTACT WITH OIL OR CHEMICALS, IT MAY BECOME DETERIORATED.

Safety Instructions

■ READ AND KEEP THIS OWNER’S MANUAL FOR LATER

USE.

All the safety and operating instructions should be read before beginning to operate the product.

Read all of the instructions given here and retain them for later use. Unplug this projector from the AC power supply before cleaning. Do not use liquid or aerosol cleaners on the projector. Use a damp cloth for cleaning.

Follow all warnings and instructions marked on the projector.

For added protection of the projector during a lightning storm, or when it is left unattended or unused for long periods of time, unplug it from the wall outlet. This will prevent damage due to lightning and power surges.

Do not expose this unit to rain or use near water... for example, in a wet basement, near a swimming pool, etc...

Do not use attachments not recommended by the manufacturer as they may result in hazards.

Safety Instructions

Do not place this projector on an unstable cart, stand, or table. The projector may fall, causing serious injury to a child or adult, and serious damage to the projector. Use only with a cart or stand recommended by the manufacturer, or sold with the projector. Wall or shelf mounting should be carried out in accordance with the manufacturer’s directions, and should use a mounting kit approved by the manufacturers. An appliance and cart combination should be moved with care. Sudden stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

Slots and openings in the rear and front of the cabinet are provided for ventilation, to insure reliable operation of the equipment and to protect it from overheating.

The openings should never be covered with cloth or other materials, and the bottom opening should not be blocked by placing the projector on a bed, sofa, rug, or other similar surface. This projector should never be placed near or over a radiator or heat register.

This projector should not be placed in a built-in installation such as a book case unless proper ventilation is provided.

Safety Instructions

Never push objects of any kind into this projector through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind onto the projector.

Do not install the projector near the ventilation duct of air-conditioning equipment.

This projector should be operated using only the type of power source indicated on the marking label. If you are not sure of the type of power supplied, contact the Canon Customer Support Center or local power company.

Do not overload wall outlets and extension cords as this can result in fire or electric shock. Do not allow anything to rest on the power cord. Do not locate this projector where the cord may be damaged by people walking on it.

Do not attempt to service this projector yourself as opening or removing covers may expose you to dangerous voltages or other hazards. Refer all servicing to qualified service personnel.

Unplug this projector from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the power cord or plug is damaged or frayed. b. If liquid has been spilled into the projector. c. If the projector has been exposed to rain or water. d. If the projector does not operate normally after following the operating

instructions. Adjust only those controls that are covered in the operating instructions as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the projector

to normal operating condition. e. If the projector has been dropped or the cabinet has been damaged. f. When the projector exhibits a distinct change in performance-this indicates a

need for servicing.

When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer that have the same characteristics as the original parts. Unauthorized substitutions may result in fire, electric shock, or injury.

Upon completion of any service or repairs to this projector, ask the service technician to perform routine safety checks to determine that the projector is in safe operating condition.

Safety Instructions

Ground

AC Power Cord Requirement

The AC Power Cord supplied with this projector meets the requirements for use in the country you purchased it.

AC Power Cord for the United States and Canada:

The AC Power Cord used in the United States and Canada is listed by the Underwriters Laboratories (UL) and certified by the Canadian Standard Association (CSA). The AC Power Cord has a grounding-type AC line plug. This is a safety feature to ensure the plug fits into the power outlet. Do not try to tamper with this safety feature. Should you be unable to insert the plug into the outlet, contact your electrician.

THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.

Only for European Union and EEA (Norway, Iceland and Liechtenstein)

These symbols indicate that this product is not to be disposed of with your household waste, according to the WEEE Directive (2012/ 19/EU), the Battery Directive (2006/66/EC) and/or national legislation implementing those Directives. If a chemical symbol is printed beneath the symbol shown above, in accordance with the Battery Directive, this indicates that a heavy metal (Hg = Mercury, Cd = Cadmium, Pb = Lead) is present in this battery or accumulator at a concentration above an applicable threshold specified in the Battery Directive. This product should be handed over to a designated collection point, e.g., on an authorized one-for-one basis when you buy a new similar product or to an authorized collection site for recycling waste electrical and electronic equipment (EEE) and batteries and accumulators. Improper handling of this type of waste could have a possible impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. Your cooperation in the correct disposal of this product will contribute to the effective usage of natural resources. For more information about the recycling of this product, please contact your local city office, waste authority, approved scheme or your household waste disposal service or visit www.canon-europe.com/weee

, or www.canon-europe.com/battery.

Safety Instructions

Federal Communication Commission Notice

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. The cable with a ferrite core provided with the projector must be used with this equipment in order to comply with Class A of the FCC Rules. Use of a shielded cable is required to comply with Class A of FCC Rules. Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment.

Warning: This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. The cable with a ferrite core provided with the projector must be used with this equipment in order to comply with Class A. Use of a shielded cable is required to comply with Class A.

Safety Instructions

Safety Symbols in this Manual

This section describes the safety symbols used in this manual. Important projector safety information is identified by the following symbols. Always observe the safety information by these symbols.

Denotes the risk of death or serious injury from improper handling if the information is not observed. To ensure safe use, always observe this information.

Denotes the risk of injury from improper handling if the information is not observed. To ensure safe use, always observe this information.

Denotes the risk of electric shock from improper handling if the information is not observed. To ensure safe use, always observe this information.

Denotes the risk of burns from improper handling if the information is not observed. To ensure safe use, always observe this information.

Denotes the risk of eye injury from laser emission if usage restrictions are not observed.

Safety Instructions

Denotes prohibited actions.

Denotes required actions or information that must be observed.

Safety Instructions

Precautions for Use

As this section contains important safety-related information, be sure to read the following carefully beforehand in order to use your projector correctly and safely.

Power Supply

During installation, keep the projector plug easily accessible so that the projector can be unplugged immediately if necessary, or keep a circuit breaker within reach. If the following situations occur, turn the power off, remove the power plug from the power outlet and contact the Canon Customer Support Center. Failure to do so could cause a fire or result in an electric shock.

• If smoke is emitted

• If an unusual smell or noise is emitted

• If water or other liquid has entered the projector

• If metal or any other foreign material has entered the projector

• If the projector is knocked over or dropped and the cabinet is

damaged

Pay attention to the following points regarding the power source, power plug and handling of the connector. Failure to do so may cause a fire or electric shock.

• Do not place any objects on the power cord and do not allow it to become trapped under the projector.

• Do not cover the power cord with a carpet.

• Do not modify or excessively bend, twist, pull, wind, or bundle the

power cord.

• Keep the power cord away from heaters and other sources of heat.

• Do not use a damaged power cord. If the power cord is damaged, contact the Canon Customer Support Center.

•

Do not use any power source with a voltage other than the voltage indicated (AC 100 – 240 V).

• Do not insert any metal objects into the contact parts of the power plug or connector.

• The power cord included with this projector is for use exclusively with this product. Do not use this cord for other products.

• Do not remove the power plug or connector with wet hands.

Safety Instructions

Pay attention to the following points regarding the power source, power plug and handling of the connector. Failure to do so may cause a fire or electric shock.

• Insert the power plug and connector securely up to the base. Additionally, do not use a damaged power plug or an outlet that is loose.

• Do not pull the power cord and be sure to hold the power plug or connector when removing. Incorrect handling may damage the power cord.

• When using an extension cord, do not exceed the cord’s rated capacity.

• Do not exceed the rated capacity of the outlet (as by using it for more than one piece of equipment), which poses a risk of fire from overheating.

• Periodically inspect the power plug and outlet and remove any dust or dirt from between the plug and the outlet.

• Do not touch the projector itself, the power cord, or the cable if lightening strikes.

• Do not move the projector until you have switched off the power, removed the power plug from the power outlet and unplugged any other cables.

• Unplug the projector before cleaning or maintenance.

• Before you install or remove the lens unit, be sure to unplug the

power plug of the projector from the power outlet.

Safety Instructions

Installation and Use

Pay attention to the following points regarding installation and handling of the projector. Failure to do so may cause a fire, electric shock or personal injury.

• Do not use the projector where it might get wet, such as outdoors or by bathtubs or showers.

• Do not place containers containing a liquid on top of the projector.

• Make sure to implement anti-fall measures such as an anti-fall wire when installing the projector in high places, for example, installing it on the ceiling.

• Do not remove the cabinet from the projector or disassemble it. The interior of the projector contains high-voltage components as well as parts that are hot. If inspection, maintenance or repair is required, contact the Canon Customer Support Center.

• Do not disassemble or modify the projector (including consumable parts) or the remote control.

• Do not look directly into the exhaust vents during use.

• Do not insert any object into vents in the projector, such as the air

intake vent or exhaust vents.

• Do not place a pressurized can in front of the exhaust vents. The pressure of the contents of the can may increase due to heat from the exhaust vents and this could result in an explosion.

• When cleaning off dust or dirt from projector parts such as the lens or filter, never use any spray that is flammable. Internal parts that become hot may ignite and cause a fire.

• Do not use adhesives, lubricants, oils, or alkaline detergents for maintenance of the projector. They could adhere to the cabinet and damage it, possibly resulting in the projector falling from its mounting and causing an accident or personal injury.

• As strong light beams are emitted while the projector is in use, do not look directly into the projector lens. Doing so could cause an eye injury. Pay particular attention to prevent small children from doing so.

• Operators shall control access to the beam within the hazard distance or install the product at a height that will prevent eye exposure within the hazard distance.

Safety Instructions

Pay attention to the following points regarding installation and handling of the projector. Failure to do so may cause a fire, electric shock or personal injury.

• Light from the projector is classified as Risk Group 2 (RG2) according to IEC 62471-5:2015. However, it may be classified as Risk Group 3 (RG3) when a replacement lens with a projection ratio larger than 2.6 is used. Refer to the Hazard Distance table for various replacement lenses.

• Do not hold or install optical instruments (such as magnifying glasses, reflectors, or glasses) in the path of light from the projector. If projected light is refracted or reflected and enters people’s eyes, it may result in eye injury.

• If children may approach the projector or touch it, always ensure the projector is used under adult supervision.

• No direct exposure to the beam shall be permitted.

• Do not lift the projector alone. Have at least one assistant.

• When setting the projector on a high surface for projection, be

sure the surface is flat and stable.

• Do not use the projector on a soft surface such as carpet or sponge mat, etc.

• For ceiling mounting or other installation work, request service from a qualified technician or the Canon Customer Support Center. Poor installation work could result in an accident.

• To avoid hazards such as parts falling when the lens of a ceilingmounted projector is replaced, request service from a qualified technician or the Canon Customer Support Center.

• Do not use where combustible or explosive gases may occur. Internal parts that become hot may ignite and cause a fire.

Safety Instructions

Hazard Distance When Equipped with a Replacement Lens (IEC 62471-5)

Projection ratio*

RS-SL01ST 1.49-2.24:1 —*

RS-SL02LZ 2.19-3.74:1 167 cm (5.5') 167 cm (5.5') 167 cm (5.5')

RS-SL03WF 0.80:1 —*

RS-SL04UL 3.55-6.94:1 400 cm (13.1') 400 cm (13.1') 400 cm (13.1')

RS-SL05WZ 1.00-1.50:1 —*

RS-SL06UW 0.54:1 —*

*1Projection ratios are calculated values based on a 16:10 screen aspect and

100-inch screen size.

Light from the projector is classified as Risk Group 2 (RG2) according to IEC 62471-5:2015.

WUX7000Z WUX6600Z WUX5800Z

Safety Instructions

Hazard Distance

• During projection, looking into the lens from distances closer than this poses a

risk of vision impairment or other serious injury.

• When a projection lens with a hazard distance indicated on it is used with the projector, the operator shall either install the product at a height that will prevent eye exposure within the hazard distance or control access to ensure that persons do not approach within the hazard distance.

Laser Light Source

• The projector is designated as a Class 1 laser product according

to IEC/EN 60825-1:2014.

• The equipment is designated as a Class 3R laser product according to IEC/EN 60825-1:2007.

• Complies with FDA performance standards for laser products except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007.

• Laser parameters

Wavelength: 450 nm – 460 nm Maximum power: 144 W Beam divergence: 2°

• The projector incorporates a laser module. Disassembly or modification is dangerous and must not be attempted.

• Operate and adjust the projector only as described in this manual. Incorrect operation or adjustment poses a risk of exposure to potentially hazardous laser light.

• Do not use when damaged. Even if the projector is used as described in this manual, failure to discontinue use when it is damaged (as indicated by screen abnormalities) may result in fire, electric shock, or eye injury from laser light.

• For assistance when disposing of the projector, contact the Canon Customer Support Center. Do not disassemble the projector yourself when disposing of it.

• Do not attempt to install or remove the lens unit yourself. Be sure to request this service from a qualified technician or contact the Canon Customer Support Center.

Safety Instructions

Explanatory and warning labels are located in the following positions on the projector.

Safety Instructions

Remote Control Batteries

Pay attention to the following points regarding handling of batteries. Failing to do so could result in a fire or personal injury.

• Do not heat, short circuit or disassemble the batteries, or place them in a fire.

• Do not attempt to recharge the batteries that are included with the remote control.

• Remove the batteries when they are flat or when the remote control will not be used for a long period of time.

• When replacing the batteries, replace both at the same time. Also, do not use two batteries of a different type at the same time.

• Insert the batteries with the + and – terminals in the correct directions.

• If any liquid from inside the batteries leaks out and contacts your skin, be sure to wash the liquid off thoroughly.

Safety Instructions

Handling

Pay attention to the following points regarding installation and handling of the projector.

• If the projector will not be used for a long period of time, be sure to remove the power plug from the power outlet to ensure safety. Failure to do so presents a risk of fire if dust accumulates on the plug or outlet.

• Do not plug headphones or earphones into the AUDIO OUT terminal. Doing so may cause hearing impairment.

• Do not set the volume too high initially. Doing so may cause hearing impairment from sudden sounds played at high volume. Lower the volume before turning off the projector, and after startup, raise it gradually.

• Do not touch parts of the cabinet around and above the exhaust vents, which may become hot during projection. Pay particular attention in preventing young children from touching these parts. Additionally, do not place any metal objects around or above the exhaust vents. Such objects may become hot from the projector, which may result in burns or other injury.

Safety Instructions

Pay attention to the following points regarding installation and handling of the projector.

• Do not place any heavy objects on top of the projector or sit/ stand on it. Pay particular attention to prevent small children from doing so. The projector may be knocked over and this could result in damage or a personal injury.

• Do not place the projector on an unstable or slanted surface. Doing so may cause the projector to fall or be knocked over and could result in a personal injury.

• Do not place any objects in front of the lens during projection. Doing so could cause a fire.

• The projector is provided with a lens shift function to move the lens up, down, left, and right using the motor. Do not touch the lens while it is moving. Touching the lens when it is moving may result in personal injury.

• Before replacing the lens unit, wait at least 30 minutes after the projector is turned off to allow the lens unit to cool down. Failure to do so may result in burns or injury.

For Safe Use

Carrying and Installation

Pay attention to the following points when carrying or transporting the projector.

• If transportation is necessary, the lens unit should be removed before transporting the projector. If the projector is subjected to excessive impacts during transportation, the lens unit may be damaged.

• This projector is a precision instrument. Do not knock it over or subject it to impacts. Doing so may cause a malfunction.

• Retract the adjustable feet before moving the projector. Leaving the feet extended may cause damage.

• When carrying or holding up the projector after attaching the lens unit, be sure not to hold the lens. Doing so may cause damage to the lens unit.

• Do not touch the lens with bare hands. Any smudges or fingerprints on the lens may affect image quality.

• Protection of the projector cannot be guaranteed if used packaging or shockabsorbent materials are reused. Fragments from shock-absorbent material may also enter the interior of the projector which could cause a malfunction.

For Safe Use

At least 50 cm (1.6')

At least 2cm (0.8")

Pay attention to the following points when installing or using the projector.

• Be careful of condensation. If the projector is abruptly taken to a warmer location, or if the room temperature rises abruptly, moisture in the air may condense on the lens or mirror and affect projected images. In this case, wait a while and make sure the moisture has evaporated before resuming use.

• Do not install the projector in a location where the temperature is high or low. Doing so may cause a malfunction. Ranges for the environment of use and storage are as follows.

• Environment of use: 0°C (32°F) to 45°C (113°F), 20% to 85% RH

• Storage temperature: -20°C (-4°F) to 60°C (140°F)

• When using the projector at altitudes above 2,300 m (7,545.8'):

Adjust projector installation settings from the menu (P154).

• Install the projector leaving at least 50 cm (1.6') between air intake/exhaust vents and walls on each side of the projector. Leave a gap of at least 2 cm (0.8") from the bottom of the projector. There is an air intake underneath the projector. Failure to leave enough space may trap heat inside the projector and damage it.

• Do not place any objects on top of the projector that may change shape or color due to heat.

• Do not install the projector near high-voltage electrical power lines or an electrical power source. This may cause malfunction.

• Afterimages may occur when the image changes after the same image has been projected for some time. This is due to the nature of the LCD panels and does not indicate a problem. The afterimage will dissipate after a while during normal projection.

Before Installation

Precautions When Carrying / Shipping the Projector

Prepare the projector as described below before carrying it.

• Disconnect the cables connected to the projector. Carrying the projector with the cables attached may cause an accident.

• Retract the adjustable feet before moving the projector. Leaving the feet extended may cause damage.

• Do not subject the projector to strong impacts or vibrations.

Precautions for Installation

Be sure to read “Safety Instructions” and “For Safe Use” (P7 – P23). Also take the following precautions during installation.

• Do not strike the projector or subject it to impact. Doing so may cause a malfunction.

• Do not install the projector standing on one side or in other unsteady positions. The projector may be damaged if it tips over.

Before Installation

■ Do Not Use in the Following Environments

• Locations with excessive humidity, dust, oily smoke or tobacco smoke

Adhesion to the lens, mirrors or other optical parts may reduce image quality.

• Near high-voltage power lines or sources of electrical power

This may cause malfunction.

• On soft surfaces such as carpets or cushioned mats

This may cause a fire or damage the projector.

• Locations with excessive temperature or humidity

• Locations subject to vibration or impact

• Near heat or smoke detectors

• Near the ocean, or near air conditioner vents

• Locations where corrosive gases occur, such as sulfur gas from hot springs

This may damage the projector. Acceptable ranges for operating and storage temperature and humidity are as follows. * Operating temperature and humidity applies to when the projector

is projecting or in standby mode.

Operating temperature Operating humidity Storage temperature

0°C (32°F) – 45°C (113°F)

20%

–

85%

-20°C (-4°F) – 60°C (140°F)

Before Installation

Exhaust vent

Air intake vent

Warmed airflow

Air intake vent

■ Do Not Touch the Lens with Bare Hands

Do not touch the lens with bare hands. Any smudges or fingerprints on the lens may affect image quality.

■ Allow a 30 Min. Warm Up before Focus Adjustment (P48), if Possible

Immediately after startup, the heat of the light source may prevent stable focus. When adjusting focus, it is also helpful to use the test pattern (10) (P107, P160).

■ Install at a Sufficient Distance from Walls and Other Obstructions

If the air intake or exhaust vent is blocked, heat will accumulate inside the projector, possibly resulting in a shortened projector lifetime or a malfunction. Similarly, do not install in narrow, enclosed spaces with poor ventilation. Install in a well-ventilated location. Ensure a minimum clearance of 50 cm (1.6') above, on both sides, and behind the projector. Also ensure a minimum clearance of 2 cm (0.8") below the projector.

■ Be Careful of Condensation

If the temperature of the room rises suddenly, moisture in the air may condense on the projector lens and mirror, causing the image to become blurred. Wait until the condensation has evaporated for the image projected to return to normal.

■ At Altitudes above 2,300 m (7,545.8'), Adjust the Settings

Projector settings must be adjusted when using the projector at altitudes of 2,300 m (7,545.8') or higher. Specifically, refer to instructions for [High altitude] (P154) in the [Install settings] menu.

Before Installation

■ When Using Mounted on the Ceiling

When the projector is used mounted on the ceiling or installed in a high location, it is necessary to periodically clean the air intake and exhaust vents, and the area around the air filter. Dust that accumulates in intake or exhaust vents may impair ventilation, raising the temperature inside and posing a risk of damage or fire. Use a vacuum cleaner or similar means to remove dust from the intake vent and exhaust vent.

■ Install Facing in the Correct Direction

• Projection is possible upward, downward, or in a variety of directions, but do not block the air intake and exhaust vents. In particular, always ensure a minimum clearance of 2 cm (0.8") from the air intake vent on the bottom of the projector.

• There are no options for installing the projector other than the ceiling attachment.

Before Installation

■ Precautions for Portrait (Upright) Installation

• Do not block the air intake or exhaust vents. In particular, because there is an air intake vent on the bottom, always ensure a minimum clearance of 2 cm (0.8") from the bottom.

• Note that no mounting brackets or similar accessories for portrait installation are available.

■ Light Source

The projector uses laser as a light source. The laser has the following characteristic.

Factors such as long-term use and environmental changes may affect image quality. You can counteract changes in brightness from hours of use or the ambient temperature by performing [Light source calibration] in [Calibration] (P180).

Before Installation

Please note that enlarging or reducing the size of an image for commercial purposes or public presentation may infringe on the legally protected copyright or the copyright holder of the original material.

Ensure Network Security

Take measures to ensure network security. Note that Canon is not liable in any way for direct or indirect loss from network security incidents, such as unauthorized access.

Before use, configure projector, computer, and network security settings appropriately.

• Set up the projector for connections only within your protected network, behind a firewall or the like, instead of direct Internet connections.

• When using the projector in a wireless network, also configure the Wi-Fi security settings.

• Change the Wi-Fi security key on a regular basis.

About Trademarks

• Ethernet is a registered trademark of Xerox Corporation.

• Microsoft and Windows are registered trademarks or trademarks of Microsoft

Corporation in the United States and/or other countries.

• Mac, Mac OS and Macintosh are trademarks of Apple Inc., registered in the United States and/or other countries.

• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing, LLC.

• PJLink is a registered trademark of JBMIA and pending trademark in some countries.

• PJLink is a registered trademark, or an application has been submitted for trademark, in Japan, the United States and/or other countries or regions.

• AMX is a registered trademark of Harman International Industries, Inc.

• Crestron®, Crestron RoomView®, and Crestron Connected™ are registered

trademarks of Crestron Electronics, Inc.

• Extron and XTP are trademarks or registered trademarks of RGB Systems, Inc. in the United States and/or other countries.

• HDBaseT™ and the HDBaseT Alliance logo are trademarks of the HDBaseT Alliance.

• Wi-Fi is a registered trademark of the Wi-Fi Alliance.

• Wi-Fi CERTIFIED, WPA, WPA2, and the Wi-Fi CERTIFIED logo are used in

reference to methods of configuration developed by the Wi-Fi Alliance.

• All other trademarks are the property of their respective owners.

Before Installation

Complies with

IMDA Standards

DB00671

Wireless LAN (Wi-Fi)

■ Countries and Regions Where Wireless LAN Use Is Permitted

Use of the wireless LAN function is restricted under the laws, etc., of each country and region, and violation of these restrictions may be subject to punishment. Check the Canon website for a list of countries and regions where use of the wireless LAN function permitted. Canon assumes no responsibility whatsoever for problems, etc., that may arise from use of the wireless LAN function in countries and regions other than those listed.

■ Model Number

WUX7000Z/WUX6600Z/WUX5800Z (including WLAN module model: ES202)

Statement on EC directive

Hereby, Canon Inc. declares that this equipment is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following Internet address: http://www.canon-europe.com/ce-documentation

Wireless LAN Specifications WUX7000Z/WUX6600Z/WUX5800Z

Frequency band(s): 2,401 MHz – 2,473 MHz Maximum radio-frequency power: 9.48 dBm

FCC/IC NOTICE Model: WUX7000Z/WUX6600Z/WUX5800Z (including WLAN Module Model ES202, FCC ID: AZD239)

This device complies with Part 15 of FCC Rules and ISED’s applicable licenceexempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device.

This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter except Canon accessories supplied or designated for this product.

This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment should be installed and operated keeping the radiator at least 20 cm or more away from person’s body.

+ 210 hidden pages