Canon DR-4010C Owner's Manual

Document Scanner

Reference Guide

Please read this manual before operating this scanner.
After you finish reading this manual, store it in a safe
place for future reference.

FCC REGULATIONS (For 120 V model)

Document Scanner, Model M11059

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference,
and
(2) this device must accept any interference received, including interference that may cause undesired
operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment OFF and ON, the user is encouraged to try to correct the
interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Use of shielded cables are required to comply with Class B limits in Subpart B of Part 15 of FCC Rules.

Do not make any changes or modifications to the equipment unless otherwise specified in this manual. If
you make such changes or modifications should be made, you could be required to stop operation of the
equipment.

If your equipment malfunctions, please contact your local authorized Canon dealer from whom you
purchased the equipment (if under warranty), or with whom you have a servincing contact. If you are not
sure who to contact, and have both purchased and are using the equipment in the U.S.A., please refer to
the “SUPPORT” page on Canon U.S.A.’s Web site (http://www.usa.canon.com).

Radio Interference Regulations (For 120 V Models)

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus
as set out in the Interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of the
Industry Canada.

RÈGLEMENT SUR LE BROUILLAGE RADIOÉLECTRIQUE (For 120 V Models)

Cet appareil numérique respecte les limites de bruits radioélectriques applicables aux appareils
numériques de Classe B prescrites dans la norme sur le matériel brouilleur: “Appareils Numériques”,
NMB-003 édictée par l’Industrie Canada.

Product Names

Safety regulations require the product’s name to be registered. In some regions where this product is sold,
the following name may be registered instead.

Model DR-4010C: M11059

i

READ CAREFULLY BEFORE OPENING THE SEALED DISK PACKAGE

CANON SOFTWARE LICENSE AGREEMENT

IMPORTANT-READ THIS AGREEMENT BEFORE OPENING THE SEALED DISK PACKAGE! BY OPENING THE

SEALED DISK PACKAGE, YOU ARE DEEMED TO AGREE TO BE BOUND BY THIS AGREEMENT.

This legal document is a license agreement between you and Canon Electronics Inc. (“Canon”). BY OPENING THE SEALED DISK
PACKAGE, YOU ARE DEEMED TO AGREE TO BE BOUND BY THE TERMS OF THIS AGREEMENT. IF YOU DO NOT AGREE TO THE
TERMS OF THIS AGREEMENT, DO NOT OPEN THE SEALED DISK PACKAGE AND PROMPTLY RETURN THE CANON SCANNER, THE
DISK PACKAGE CONTAINING SCANNER DRIVER SOFTWARE PROGRAMS AND/OR SCANNER UTILITY SOFTWARE PROGRAM
PROPRIETARY TO CANON OR ITS LICENSOR (THE “SOFTWARE”) AND THE ACCOMPANYING DOCUMENTATION AND OTHER
ITEMS TO THE PLACE WHERE YOU OBTAINED THEM FOR A REFUND BEFORE THEY ARE USED OR OPENED OR UNPACKED.

In consideration of the right to use the SOFTWARE, you agree to abide by the terms and conditions of this Agreement.

1. GRANT OF LICENSE: Canon grants you the personal, non-exclusive right to use the SOFTWARE only on a single computer. You

shall need to obtain multiple licenses separately from Canon when you shall install t he SOFTWARE on multiple computers.

You shall not assign, sublicense, sell, rent, lease, loan, convey or transfer to any third party, or send or bring the SOFTWARE out of the
country where you originally obtain it to other countries without required authorization of applicable governments, or copy, duplicate, translate or
convert to another programming language the SOFTWARE or accompanying documentation, except as expressly provided herein.

Except as expressly permitted under the applicable law, you shall not alter, modify, disassemble, decompile or otherwise reverse engineer
the SOFTWARE or accompanying documentation and you also shall not have any third party do so.

2. BACK-UP COPY: You may make one copy of the SOFTWARE solely for a back-up purpose or copy the SOFTWARE onto the
permanent storage device (e.g. a hard disk) of your computer and retain the original for a back-up purpose. Except as expressly permitted under the
applicable law, any other copying of the SOFTWARE is a violation of this Agreement. You must reproduce and include the copyright notice on the
back-up copy.

3. SUPPORT AND UPDATE: Canon, Canon’s affiliate, their distributor or dealer is not responsible for maintaining or helping you to use
the SOFTWARE. No updates, fixes or support will be made available for the SOFTWARE.

4. LIMITED WARRANTY AND DISCLAIMER OF INDEMNITY: Canon, Canon’s affiliate, their distributor or dealer will not
guarantee uninterrupted service, or absence or correction of errors. Therefore, the SOFTWARE is licensed on an “AS IS” basis without warranty of
any kind. The diskette on which the SOFTWARE is recorded is warranted against defective material or workmanship under normal use for a period of
ninety (90) days from the date you purchased the same as evidenced by a receipt or otherwise. The limited warranty does not apply if the failure of the
diskette resulted from accident, abuse or misapplication of the SOFTWARE and shall not extend to anyone other than the original user of the
SOFTWARE.

CANON, CANON’S AFFILIATE, THEIR DISTRIBUTOR OR DEALER DISCLAIMS ALL IMPLIED WARRANTIES, INCLUDING
ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, WITH RESPECT TO THE SOFTWARE OR
ACCOMPANYING DOCUMENTATION.

NEITHER CANON, CANON’S AFFILIATE, THEIR DISTRIBUTOR NOR DEALER IS LIABLE FOR ANY LOSS OR DAMAGE
INCLUDING CONSEQUENTIAL OR INCIDENTAL LOSS OR DAMAGE SUCH AS LOSS OF PROFITS, EXPENSE OR INCONVENIENCE,
WHATSOEVER CAUSED BY OR ARISING OUT OF THE SOFTWARE, ACCOMPANYING DOCUMENTATION OR THE USE THEREOF.

CANON, CANON’S AFFILIATE, THEIR DISTRIBUTOR OR DEALER SHALL HAVE NO OBLIGATION TO INDEMNIFY YOU
AGAINST ANY CLAIM OR SUIT BROUGHT BY A THIRD PARTY ALLEGING THAT THE SOFTWARE, ACCOMPANYING
DOCUMENTATION OR THE USE THEREOF INFRINGES ANY INTELLECTUAL PROPERTY OF SUCH THIRD PARTY.

THE ABOVE IS CANON’S ENTIRE LIABILITY AND YOUR EXCLUSIVE REMEDY IN CONNECTION WITH THE SOFTWARE
AND ACCOMPANYING DOCUMENTATION.

5. TERM: This Agreement is effective upon opening the sealed disk package and remains in effect until terminated. You may terminate
this Agreement by destroying the SOFTWARE and any copy thereof. This Agreement will also terminate if you fail to comply with any of the terms
of this Agreement. In addition to Canon enforcing its respective legal rights, you must then promptly destroy the SOFTWARE and any copy thereof.

6. U.S. GOVERNMENT RESTRICTED RIGHTS NOTICE: The SOFTWARE is provided with RESTRICTED RIGHTS. Use,
duplication or disclosure is subject to restrictions as set forth in either subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software
clause at DFARs 252.227-7013 or subparagraph (c) (1) and (2) of the Commercial Computer Software Restricted Rights Clause at FAR 52.227-19, as
applicable.

7. SEVERABILITY: In the event that provision of this Agreement is declared or found to be illegal by any court or tribunal of competent
jurisdiction, such provision shall be null and void with respect t o the jurisdiction of that court or tribunal and all the remaining provisions of this
Agreement shall remain in full force and effect.

8. ACKNOWLEDGEMENT: BY OPENING THE SEALED DISK PACKAGE, YOU ACKNOWLEDGE THAT YOU HAVE READ
THIS AGREEMENT, UNDERSTOOD IT, AND AGREE TO BE BOUND BY ITS TERMS AND CONDITIONS. YOU ALSO AGREE THAT
THIS AGREEMENT IS THE COMPLETE AND EXCLUSIVE STATEMENT OF AGREEMENT BETWEEN YOU AND CANON
CONCERNING THE SUBJECT MATTER HEREOF AND SUPERSEDES ALL PROPOSALS OR PRIOR AGREEMENTS, VERBAL OR
WRITTEN, AND ANY OTHER COMMUNICATIONS BETWEEN YOU AND CANON R ELATING TO THE SUBJECT MATTER HEREOF. NO
AMENDMENT TO THIS AGREEMENT SHALL BE EFFECTIVE UNLESS SIGNED BY A DULY AUTHORIZED REPRESENTATIVE OF
CANON.

Should you have any questions concerning this Agreement, or if you desire to contact Canon for any reason, please write to Canon’s local affiliate.

ii

International ENERGY STAR Program

®

As an ENERGY STAR
machine meets the ENERGY STAR

The International ENERGY STAR

Partner, Canon Electronics Inc., has determined that this

®

Program guidelines for energy efficiency.

®

Office Equipment Program is an international
program that promotes energy saving through the use of computers and other office
equipment. The program backs the development and dissemination of products with
functions that effectively reduce energy consumption. It is an open system in which
business proprietors can participate voluntarily. The targeted products are office
equipment, such as computers, monitors, printers, fax, machine, copiers, and scanners.
The standards and logos are uniform among participating nations.

Trademarks

• Canon and the Canon logo are registered trademarks of Canon Inc. in the United States and may also be trademarks
or registered trademarks in other countries.

• Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and other
countries.

• ISIS is a trademark of EMC Corporation, in the United States.

• Intel and Pentium are registered trademarks of Intel Corporation.

•ENERGY STAR

• Adobe is the registered trademark of Adobe Systems Incorporated in the United States and/or other countries.

• Adaptec is registered trademark of Adaptec Inc.

• Other product and company names herein may be the trademarks of their respective owners.

®

is a U.S. registered mark.

Copyright

Copyright 2006 by CANON ELECTRONICS INC. All rights reserved.

No part of this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording, or by any information storage or retrieval system
without the prior written permission of CANON ELECTRONICS INC.

Disclaimers

The information in this document is subject to change without notice.

CANON ELECTRONICS INC. MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THIS
MATERIAL, EITHER EXPRESS OR IMPLIED, EXPECT AS PROVIDED HERE IN, INCLUDING
WITHOUT LIMITATION, THERE OF, WARRANTIES AS TO MARKETABILITY, MERCHANTABILITY,
FITNESS FOR A PARTICULAR PURPOSE OF USE OR NON-INFRINGEMENT. CANON
ELECTRONICS INC. SHALL NOT BE LIABLE FOR ANY DIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES OF ANY NATURE, OR LOSSES OR EXPENSES RESULTING FROM
THE USE OF THIS MATERIAL.

iii

Manuals for the Scanner

Thank you for purchasing the Document Scanner DR-4010C. The manuals
for this scanner include the Easy Start Guide and Reference Guide
(printed manuals provided with the scanner,) and the User Manual and
CapturePerfect 3.0 Operation Guide (electronic manuals stored on the
setup disc.) Before using the scanner, read each manual throughly to
familiarize youreself with its capabilities, and to make the most of its many
functions. After reading these manuals, store them in a safe place for
future reference.

Easy Start Guide

Describes the procedures for setting up the scanner and
instaling the software. Follow the steps in this guide to set up
the scanner quickly.

Reference Guide (this manual)

Provides an overview of the most important features and
points that the user should know when using the scanner. For
more details, refer to the User Manual.

User Manual (electronic manual)

Consists of a “Hardware” volume and a “Software” volume.
The “Hardware” volume explains all topics related to handling
and caring for the scanner (i.e., setup, cleaning,
maintenance, and troubleshooting.)
The “Software” volume explains the ISIS/TWAIN driver
settings and Job Registration Tool settings.

*

Chapter 1

Chapter 2Chapter 3Chapter 5 Chapter 4Index

CapturePerfect 3.0 Operation Guide (electronic manual)

Explains the application that enhances the operation of all
Canon document scanners.

* The electronic manuals are PDF (Portable Document Format) files, and are

installed in the following folders during software installation.

User Manual CapturePerfect 3.0 Operation Guide

*

1

Symbols Used in This Manual

The following symbols are used in this manual to explain procedures,
restrictions, handling precautions, and instructions that should be
observed for safety.

WARNING

Indicates a warning concerning operations that may lead to
death or injury to persons if not performed correctly. To use the
machine safely, always pay attention to these warnings.

CAUTION

Indicates a caution concerning operations that may lead to
injury to persons, or damage to property if not performed
correctly. To use the machine safely, always pay attention to
these cautions.

IMPORTANT

Indicates operational requirements and restrictions. Be sure to read
these items carefully to operate the machine correctly, and avoid
damage to the machine.

Note

Indicates a clarification of an operation, or contains additional
explanations for a procedure. Reading these notes is highly
recommended.

(See p. 12.)
Indicates a reference page. The number in parentheses is the
number of the page that describes the current topic in greater detail.

2

Contents

Chapter 1 Before Using the Scanner..................................... 4

1-1 Important Safety Instructions...............................4

Installation Location.................................................4

Power.......................................................................5

Moving the Scanner.................................................6

Handling...................................................................6

Disposal...................................................................8

1-2 Features of the DR-4010C Document

Scanner9

1-3 Names and Functions of Parts...........................12

1- 4 Installation Requirements...................................14

Chapter 2 Basic Operation ...................................................16

2-1 Documents ...........................................................16

2-2 Document Feed and Eject Tray...........................19

Preparing the Document Feed Tray.......................19

Preparing the Document Eject Tray ....................... 20

2-3 Placing Documents .............................................22

Feeding in the Page Separation Mode ..................22

Feeding in the Bypass Mode .................................25

2-4 Scanning...............................................................27

What Is the Job Function? .....................................27

Using CapturePerfect 3.0.......................................29

2- 5 Clearing a Paper Jam ..........................................31

Chapter3 Maintenance.........................................................34

3-1 Regular Maintenance...........................................34

Cleaning the Scanner ............................................ 34

Cleaning the Feed Path .........................................35

Cleaning the Sensor Glass and the Rollers...........35

Chapter 4 Troubleshooting ..................................................43

4-1 Troubleshooting...................................................43

Chapter 5 Appendix ..............................................................50

Specifications.........................................................50

Replacement Parts ................................................52

Options ..................................................................52

External Dimensions..............................................52

Index...........................................................................................53

3

Chapter 1

1-1 Important Safety Instructions

To ensure the safe operation of this scanner, be sure to read the safety
warnings and precautions described below.

Installation Location

The performance of this scanner is affected by the environment in which it
is installed. Make sure that the location where the scanner is installed
meets the following environmental requirements.

• Provide adequate space around the scanner for operation, maintenance,
and ventilation.

Before Using the Scanner

At least 3.9" (100 mm)
when eject tray is empty.

15.7" (400 mm)
when the document
feed tray and
document feed tray
extension are
closed.

• If scanned documents are ejected to the back tray of the scanner,
provide adequate space behind the scanner for documents ejected after
being scanned. (See “Preparing the Document Eject Tray,” on p. 20.)

• Avoid installing the machine in direct sunlight. If this is unavoidable, use
curtains to shade the scanner.

• Avoid locations where a considerable amount of dust accumulates.

25.6" (650 mm)
when the document
feed tray and
document feed tray
extension are
open.

4 Before Using the Scanner

• Avoid warm or humid locations, such as in the vicinity of a water faucet,
water heater, or humidifier.

• Avoid locations where ammonia gas is emitted.

• Avoid locations near volatile or flammable materials, such as alcohol or
paint thinner.

• Avoid locations that are subject to vibration.

• Avoid exposing the scanner to rapid changes in temperature. If the room
in which the scanner is installed is cold but rapidly heated, water droplets
(condensation) may form inside the scanner. This may result in a
noticeable degradation in scanning quality.

The following conditions are recommended for optimal scanning quality:
Room temperature: 10 °C to 32.5 °C (50 °F to 90.5 °F)
Humidity: 20% to 80% RH

• Avoid installing the scanner near equipment that generates a magnetic
field (e.g. speakers, televisions, or radios.)

Power

• Connect only to a power outlet of the rated voltage and power supply
frequency. (120 V, 60 Hz or 220-240 V, 50/60 Hz depending on your
region)

• Do not use a power supply that is not rated for the specified voltage.
Doing so might cause a fire or electric shock.

• Do not connect other electrical equipment to the same power outlet to
which the scanner is connected. Also, when using an extension cord,
make sure that the extension cord is rated for the current requirements of
the scanner.

• The power cord may become damaged if it is often stepped on or if
heavy objects are placed on it. Continued use of a damaged power cord
can lead to an accident, such as a fire or electrical shock.

• Do not use the power cord while it is coiled.

• Do not pull directly on the power cord. When disconnecting the power
cord, grasp the plug and remove it from the outlet.

• Keep the area around the power plug clear of objects so that the power
cord can be disconnected easily in an emergency.

• If you have any questions regarding the power supply, contact your local
authorized Canon dealer or service representative for further
information.

Chapter 1

Before Using the Scanner 5

Moving the Scanner

• When moving the scanner, always hold it with both hands to avoid
dropping it. The scanner weighs approximately 14.1 lb (6.4 kg).

CAUTION

• Make sure to disconnect the interface cable and power cord when
moving the scanner. If the scanner is transported with these items
plugged in, the plugs and connectors may be damaged.

Handling

WARNING

Note the following precautions whenever using the scanner. Failure
to do so may result in a fire or electric shock.

■ Never use alcohol, benzene, paint thinner, aerosol sprays, or any

other highly flammable substance near the scanner.

■ Do not cut, damage, or modify the power cord. Do not place heavy

objects on the power cord, and do not pull or excessively bend the
power cord.

■ Never connect the power cord when your hands are wet.

■ Do not connect the scanner to a multi plug power strip.

■ Do not knot or coil the power cord as this may result in a fire or

electric shock. When connecting the power cord, make sure that
the power plug is securely and completely inserted into the power
outlet.

■ Do not use power cords other than the power cord provided with

this scanner.

■ Never try to take the scanner apart or modify it in any way, as this

is dangerous and may lead to a fire or electric shock.

6 Before Using the Scanner

■ When cleaning the scanner, turn the power switch OFF and

disconnect the power cord from the power supply.

■ Clean the scanner using a slightly dampened cloth which has

been well wrung out. Never use alcohol, benzene, paint thinner, or
any other flammable substances.

■ If the scanner makes strange noises, or gives off smoke, heat, or

strange odors, or the scanner does not function or other
abnormalities occur when you use the machine, immediately turn
the power switch OFF, and disconnect the power plug from the
power outlet. Then, contact your local authorized Canon dealer or
the service representative for further information.

■ Do not drop the scanner, or subject it to impact or strong shock.

Should the scanner ever become damaged, immediately turn the
power switch OFF, and disconnect the power plug from the power
outlet. Then, contact your local authorized Canon dealer or service
representative to have the unit serviced.

■ Before moving the scanner, be sure to turn the power switch OFF,

and disconnect the power plug from the power outlet.

CAUTION

■ Do not install the scanner on a surface that is unstable or tilted, or

in an area subject to excessive vibrations, as this may cause the
scanner to fall, resulting in personal injury or damage to the
scanner.

■ Do not block ventilation openings. Doing so could case the

scanner to overheat, creating a risk of fire.

■ Never place small metal objects such as staples, paper clips, or

jewelry on the scanner. These items may fall into the scanner, and
cause a fire or electric shock. Should such objects ever fall inside
the scanner, immediately turn the power switch OFF, and
disconnect the power plug from the power outlet. Then, contact
your local authorized Canon dealer or service representative to
have the unit serviced.

■ Do not install the scanner in a humid or dusty location. Doing so

might cause a fire or electric shock.

■ Do not place objects on top of the scanner. Such objects may tip

or fall over, resulting in personal injury.

■ When unplugging the power cord, grasp it firmly by its plug. Do

not pull directly on the power cord, as this may damage or expose
the cord’s internal wiring, resulting in a fire or electric shock.

Chapter 1

Before Using the Scanner 7

■ Leave sufficient space around the power plug so that it can be

unplugged easily. If objects are placed around the power plug, you
will be unable to unplug it in an emergency.

■ Do not allow water or flammable substances (alcohol, paint

thinner, benzene, etc.) to spill into the scanner, as this may result
in a fire or electric shock.

■ Turn OFF the power switch for safety when not using the scanner

for a long period of time, such as overnight. Also, turn OFF the
power switch, and disconnect the power cord from the power
outlet for safety when the machine will not be used for an
extended period of time, such as during consecutive holidays.

■ Do not wear loose clothing or jewelry that may get caught in the

scanner while you are using it. This may result in personal injury.
Be extra careful of neckties and long hair. If anything becomes
caught in the scanner, immediately disconnect the power cord to
stop the scanner.

■ Be careful when placing paper in the scanner and when removing

jammed paper. It is possible to cut your hand on the edge of a
sheet of paper.

Disposal

When disposing of this scanner, be sure to follow all local ordinances and
laws or consult with the retailer who sold you the scanner.

8 Before Using the Scanner

1-2 Features of the DR-4010C

Document Scanner

The main features of the DR-4010C document scanner are described
below.

• Fast Document Feeding

The scanner can scan a maximum of 42 documents per minute in a
range of sizes from business cards to LTR/A4 size. (Scanning
conditions: Black and white, LTR/A4 size portrait, 200 dpi.) Scanning
speed is the same for both color and grayscale scanning.

• USB/SCSI Interface Supported

The USB interface that was provided as standard on your computer and
SCSI extension cards are supported. (See “1-4 Installation
Requirements,” on p. 14.)

• Color/Grayscale Support

Documents can be scanned in 24-bit color or 256-level grayscale.

• Supports a Variety of Scanning Modes

The scanner supports the following scanning modes, depending on the
document type:

- Single-sided/double-sided mode

- Single sheet/dual feeding path

• U-Turn Path

Documents are fed and ejected from the front of the scanner. (See “2-2
Document Feed and Eject Tray,” on p. 19.)

• Straight Path

Documents are ejected to the back of the scanner. Note that the ejected
documents are stacked in the reverse order from which they were fed.
(See “2-2 Document Feed and Eject Tray,” on p. 19.)

• Paper Size Detection

The scanner automatically detects the size of a scanned document and
eliminates any unnecessary space around the edges of the image
when storing the image, even when storing a document of irregular
size.

• Double Feed Detection

The scanner stops feeding documents after detecting more than one
document being fed at the same time.

• Deskew

The scanner straightens images after detecting that a document was
placed askew.

Chapter 1

Before Using the Scanner 9

• Card Scan

You can scan business or ID cards. Note that embossed credit cards or
similar items cannot be scanned. (See “2-1 Documents,” on p. 16.)

• Auto Color Detection

The scanner detects whether the scanned document is in color or
black-and-white, and saves the image accordingly.

• Text Orientation Recognition

This mode identifies the orientation of characters in a document, and
rotates the image so the orientation of the scanned characters is
straight.

• Text Enhancement Mode

This mode enables you to scan documents with dark backgrounds or

documents with faint text written in pencil clearly.

Note

This mode may not function effectively, depending on the document
type.

• Dropout Color

The scanner is equipped with a Dropout Color function that enables you
to specify a color for the scanner to omit from the scanned image.

• Color Enhancement

The scanner is equipped with a Color Enhancement function that
enables you to specify a color for the scanner to enhance on the
scanned image.

• Skip Blank Page Function

The scanner is equipped with a Skip Blank Page function that enables
you to scan a document without storing images of blank pages,
regardless of whether each page of the document is two-sided or one­sided.

• Prescan Function

The scanner is equipped with a Prescan function that allows you to
adjust the contrast and brightness of a prescanned image and then
send the adjusted image to the application software, without needing to
scan the document again.

• Remove Binder Holes

This mode erases the black spots that appear on scanned images from
binding holes on the original document.

10 Before Using the Scanner

• MultiStream Function

The scanner supports MultiStream, which, according to the application,
can create two images with different scanning conditions from one path
scan.
However, this function can only be used if the software supports
MultiStream.

• Long Document Compatibility

You can scan documents up to 39.2 inches (1000 mm) long by setting
the Long Document mode.

• Compatible with Carbonless Duplicating Paper

The scanner is able to scan carbonless duplicating paper.

• Energy Saving Mode

This scanner is compatible with the International Energy Star Program,
and is designed to save power by using the energy saving feature
except when scanning is being performed.

Note

Some functions may not be available depending on the software you
are using.

Chapter 1

Before Using the Scanner 11

1-3 Names and Functions of Parts

This section describes the name and function of each part. Make sure to
read this section and familiarize yourself with the parts of the scanner
before using the scanner.

■ Front View (Feed Tray Open)

Document
Eject Tray

Scanned

Document Eject Tray Extension

Open if the document extends beyond the edge of the
eject tray. (See p. 20.)

Document Feed Tray

Place the document to be
scanned here. (See p. 19.)

Document Feed
Tray Extension

Pull this tray out if the
document hangs over
the edge of the main
tray.
(See p. 19.)

Document Guides

Adjust these guides to fit the width of the
document.(See p. 23.)

documents are
ejected here.

(See p. 20.)

■ Controls

12 Before Using the Scanner

Job Buttons

These buttons can perform user-specified functions
assigned with the Job Registration Tool. (See p. 28.)

Power Indicator

This indicator lights when the scanner is turned ON.

Feed Selection Lever

Use this lever to change the way documents are fed.
Push it down ( ) to feed documents continuously
(page separation mode.) (See p. 22.)
Push it up ( ) to feed documents one at a time or
to feed documents that are fastened together, such
as invoices, without separating them (bypass mode.)
(See p. 25.)

Power Switch

This switch is used to turn the scanner ON.

■ Back View

Document Eject Tray 2

Open this tray to use the
scanner in a straight path
configuration. (See p. 20.)

■ Interfaces

1ON2

Chapter 1

DIP Switches

Set the SCSI ID.

SCSI Connector

Connect to a 50-pin half-pitch (pin type) SCSI cable.

(Ventilation Holes)

USB Connector

Connect the provided USB cable or
a USB cable that supports Hi­Speed USB 2.0.

Powe r
Connector

CAUTION

• Do not block the ventilation openings. Doing so could cause
the scanner to overheat, creating a risk of fire.

• Do not connect both a USB cable and a SCSI cable at the
same time. Doing so may cause a malfunction.

Before Using the Scanner 13

1-4 Installation Requirements

To use the DR-4010C scanner, your computer must satisfy the following
system requirements.

• One of the following operating systems:

- Microsoft Windows 2000 Professional SP4 or later

- Microsoft Windows XP Professional SP2 or later

- Microsoft Windows XP Home Edition SP2 or later

- Microsoft Windows XP Professional x64 Edition

• A computer that meets the following specifications:

- CPU: Pentium 4 (3.2 GHz or faster)

- Memory: 1 GB or more

- Hard disk: 1 GB or more available space

- Interface: USB port present as standard equipment on the

computer (Hi-Speed USB 2.0) or SCSI expansion card

- Monitor: Resolution of 1024 × 768 (XGA) or better

recommended.

• When using a SCSI expansion card, select one of the following
recommended models.
SCSI cards made by Adaptec (for PCI bus)

- AHA-2930U

- AHA-2940AU

- ASC-19160

- ASC-29160N

SCSI card made by Adaptec (for Card bus)

- APA-1480

• An ISIS-compatible application or a TWAIN-compatible application
that is compatible with the above operating systems.

IMPORTANT

• If you do not know the requirements for your computer system,

contact the store where you purchased the computer or the
manufacturer of the computer for more information.

• Do not connect both a USB interface and a SCSI card at the same

time.

• Be aware of the following information when using the USB

interface that was provided as standard with your computer.

- The USB interface should be a Hi-Speed USB 2.0 interface.

- Scanning speeds are lower if your computer’s standard USB

interface is USB Full-Speed (equal to USB 1.1.) In this case,

using a SCSI expansion card is recommended.

- Use the latest USB 2.0 driver made available by Microsoft. For

details, consult your local authorized Canon dealer.

14 Before Using the Scanner