Brother Innov-is VM5100 Operation Manual
Operation Manual
Embroidery and Sewing Machine
Product Code: 882-C50
Be sure to read this document before using the machine.
We recommend that you keep this document nearby for future reference.
TRADEMARKS
IMPORTANT:
READ BEFORE DOWNLOADING, COPYING, INSTALLING OR USING.
By downloading, copying, installing or using the software you agree to this license. If you do not agree
to this license, do not download, install, copy or use the software.
Intel License Agreement For Open Source Computer Vision Library
Copyright © 2000, Intel Corporation, all rights reserved. Third party copyrights are property of their respective owners.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the
following conditions are met:
• Redistribution’s of source code must retain the above copyright notice, this list of conditions and the following
disclaimer.
• Redistribution’s in binary form must reproduce the above copyright notice, this list of conditions and the
following disclaimer in the documentation and/or other materials provided with the distribution.
• The name of Intel Corporation may not be used to endorse or promote products derived from this software
without specific prior written permission.
This software is provided by the copyright holders and contributors “as is” and any express or implied warranties,
including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose are
disclaimed. In no event shall Intel or contributors be liable for any direct, indirect, incidental, special, exemplary,
or consequential damages (including, but not limited to, procurement of substitute goods or services; loss of use,
data, or profits; or business interruption) however caused and on any theory of liability, whether in contract, strict
liability, or tort (including negligence or otherwise) arising in any way out of the use of this software, even if
advised of the possibility of such damage.
All information provided related to future Intel products and plans is preliminary and subject to change at any time, without notice.
SD is a registered trademark or a trademark of SD-3C, LLC.
CompactFlash is a registered trademark or a trademark of Sandisk Corporation.
Memory Stick is a registered trademark or a trademark of Sony Corporation.
SmartMedia is a registered trademark or a trademark of Toshiba Corporation.
MultiMediaCard (MMC) is a registered trademark or a trademark of Infineon Technologies AG.
xD-Picture Card is a registered trademark or a trademark of Fuji Photo Film Co. Ltd.
IBM is a registered trademark or a trademark of International Business Machines Corporation.
Microsoft, Windows and Windows Vista are registered trademarks or trademarks of Microsoft Corporation.
Each company whose software title is mentioned in this manual has a Software License Agreement specific to its proprietary programs.
All other brands and product names mentioned in this manual are registered trademarks of their respective companies. However, the
explanations for markings such as
® and ™ are not clearly described within the text.
INTRODUCTION
INTRODUCTION
Thank you for purchasing this machine. Before using this machine, carefully read the “IMPORTANT
SAFETY INSTRUCTIONS”, and then study this manual for the correct operation of the various functions.
In addition, after you have finished reading this manual, store it where it can quickly be accessed for
future reference.
IMPORTANT SAFETY INSTRUCTIONS
Please read these safety instructions before attempting to use the machine.
DANGER - To reduce the risk of electrical shock
1Always unplug the machine from the electrical outlet immediately after using, when cleaning, making any user
servicing adjustments mentioned in this manual, or if you are leaving the machine unattended.
WARNING - To reduce the risk of burns, fire, electrical shock, or injury to
persons.
2Always unplug the machine from the electrical outlet when making any adjustments mentioned in the instruction
manual.
• To unplug the machine, switch the machine to the symbol “O” position to turn it off, then grasp the plug and pull
it out of the electrical outlet. Do not pull on the cord.
• Plug the machine directly into the electrical outlet. Do not use an extension cord.
• Always unplug your machine if the power is cut.
3Electrical Hazards:
• This machine should be connected to an AC power source within the range indicated on the rating label. Do not
connect it to a DC power source or inverter. If you are not sure what kind of power source you have, contact a
qualified electrician.
• This machine is approved for use in the country of purchase only.
4Never operate this machine if it has a damaged cord or plug, if it is not working properly, has been dropped or
damaged, or water is spilled on the unit. Return the machine to the nearest authorized dealer for examination,
repair, electrical or mechanical adjustment.
• While the machine is stored or in use if you notice anything unusual, such as an odor, heat, discoloration or
deformation, stop using the machine immediately and unplug the power cord.
• When transporting the sewing machine, be sure to carry it by its handle. Lifting the sewing machine by any other
part may damage the machine or result in the machine falling, which could cause injuries.
• When lifting the sewing machine, be careful not to make any sudden or careless movements, otherwise you may
injure your back or knees.
B-1
IMPORTANT SAFETY INSTRUCTIONS
5Always keep your work area clear:
• Never operate the machine with any air openings blocked. Keep ventilation openings of the sewing machine and
foot control free from the build up of lint, dust, and loose cloth.
• Do not store objects on the foot controller.
• Do not use extension cords. Plug the machine directly into the electrical outlet.
• Never drop or insert foreign objects in any opening.
• Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
• Do not use the machine near a heat source, such as a stove or iron; otherwise, the machine, power cord or
garment being sewn may ignite, resulting in fire or an electric shock.
• Do not place this sewing machine on an unstable surface, such as an unsteady or slanted table, otherwise the
sewing machine may fall, resulting in injuries.
6Special care is required when sewing:
• Always pay close attention to the needle. Do not use bent or damaged needles.
• Keep fingers away from all moving parts. Special care is required around the machine needle.
• Switch the sewing machine to the symbol “O” position to turn it off when making any adjustments in the needle
area.
• Do not use a damaged or incorrect needle plate, as it could cause the needle to break.
• Do not push or pull the fabric when sewing, and follow careful instruction when free motion stitching so that
you do not deflect the needle and cause it to break.
7This machine is not a toy:
• Your close attention is necessary when the machine is used by or near children.
• The plastic bag that this sewing machine was supplied in should be kept out of the reach of children or disposed
of. Never allow children to play with the bag due to the danger of suffocation.
• Do not use outdoors.
8For a longer service life:
• When storing this machine, avoid direct sunlight and high humidity locations. Do not use or store the machine
near a space heater, iron, halogen lamp, or other hot objects.
• Use only neutral soaps or detergents to clean the case. Benzene, thinner, and scouring powders can damage the
case and machine, and should never be used.
• Always consult the operation manual when replacing or installing any assemblies, the presser feet, needle, or
other parts to assure correct installation.
9For repair or adjustment:
• If the light unit is damaged, it must be replaced by an authorized dealer.
• In the event a malfunction occurs or adjustment is required, first follow the troubleshooting table in the back of
the operation manual to inspect and adjust the machine yourself. If the problem persists, please consult your
local authorized Brother dealer.
Use this machine only for its intended use as described in the manual.
Use accessories recommended by the manufacturer as contained in this manual.
Use only the interface cable (USB cable) included with this machine.
Use only the mouse designed specifically for this machine.
The contents of this manual and specifications of this product are subject to change without notice.
For additional product information and updates, visit our website at www.brother.com
B-2
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
This machine is intended for household use.
This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the
appliance by a person responsible for their safety. Children should be supervised
to ensure that they do not play with the appliance.
This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved. Children shall not
play with the appliance. Cleaning and user maintenance shall not be made by
children without supervision.
FOR USERS IN THE UK, EIRE, MALTA
AND CYPRUS ONLY
IMPORTANT
• In the event of replacing the plug fuse, use a fuse approved by ASTA to BS 1362, i.e. carrying the mark,
rating as marked on plug.
• Always replace the fuse cover. Never use plugs with the fuse cover omitted.
• If the available electrical outlet is not suitable for the plug supplied with this equipment, you should contact your
authorized dealer to obtain the correct lead.
B-3
IMPORTANT SAFETY INSTRUCTIONS
Federal Communications Commission (FCC)
Declaration of Conformity (For USA Only)
Responsible Party: Brother International Corporation
200 Crossing Boulevard
P.O. Box 6911
Bridgewater, NJ 08807-0911 USA
TEL : (908) 704-1700
declares that the product
Product Name:
Model Number:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
Brother Sewing Machine
VM5100
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
• The included interface cable should be used in order to ensure compliance with the limits for a Class B digital
device.
• Changes or modifications not expressly approved by Brother Industries, Ltd. could void the user’s authority to
operate the equipment.
B-4
WHAT YOU CAN DO WITH THIS MACHINE
WHAT YOU CAN DO WITH THIS MACHINE
B Basic operations
After purchasing your machine, be sure to read this section first. This section provides details on the
initial setup procedures as well as descriptions of this machine’s more useful functions.
Chapter 1 Getting Ready
To learn the operation of the principal parts and the screens
Page B-18
S Sewing
This section describes procedures for using the various utility stitches as well as other functions. It
provides details on basic machine sewing in addition to the more expressive features of the machine,
from sewing tubular pieces and buttonholes to sewing the character and decorative stitch patterns.
Chapter 1 Sewing Basics
To learn how to prepare for sewing and basic sewing
operations
Page S-2
Chapter 3 Character/Decorative
Stitches
The variety of stitches widen your creativity
Page S-76
Chapter 2 Utility Stitches
Pre-programmed with more than 100 frequently used
stitches
Page S-20
Chapter 4 MY CUSTOM STITCH
Create original decorative stitches
Page S-102
E Embroidering
This section provides instruction to embroider designs with this machine.
Chapter 1, “Embroidery”, provides details on sewing embroidery patterns stored on the machine as well
as patterns that have been imported. Chapter 2, “Embroidery Edit”, provides details on editing
embroidery patterns to create custom embroidery.
Chapter 1 Embroidery
Maximum 30 cm × 18 cm (approx. 12 inches × 7 inches)
for large embroidery designs
Page E-2
Chapter 2 Embroidery Edit
Designs can be combined, rotated or enlarged
Page E-56
A Appendix
This section provides important information for operating this machine.
Chapter 1 How to Create Bobbin
Work
To learn how to create bobbin work
Page A-2
Chapter 2 Maintenance and
Troubleshooting
Find troubleshooting tips and pointers as well as how
to keep your machine in the best working condition.
Page A-18
B-5
CONTENTS
CONTENTS
TRADEMARKS
INTRODUCTION ................................................. 1
IMPORTANT SAFETY INSTRUCTIONS ................ 1
WHAT YOU CAN DO WITH THIS MACHINE ..... 5
NAMES OF MACHINE PARTS AND THEIR
FUNCTIONS.......................................................... 9
Machine................................................................................. 9
Needle and Presser Foot Section .......................................... 10
Embroidery Unit................................................................... 11
Operation Buttons................................................................ 11
Using the Flat Bed Attachment............................................. 12
Included Accessories............................................................ 13
Accessories that are Included in Some Countries or
Regions ................................................................................ 15
Options................................................................................ 15
B Basic operations
Chapter1 Getting Ready 18
TURNING THE MACHINE ON/OFF................... 19
Setting Your Machine for the First Time................................ 20
LCD SCREEN ...................................................... 22
Using the Machine Setting Mode Key .................................. 26
Using the Sewing Machine Help Key .................................. 34
Using the Operation Guide Function.................................... 35
Using the Sewing Guide Function ........................................ 36
Using the Pattern Explanation Function................................ 37
LOWER THREADING ......................................... 38
Winding the Bobbin ............................................................. 38
Setting the Bobbin ................................................................ 43
Pulling Up the Bobbin Thread .............................................. 45
UPPER THREADING........................................... 46
Upper Threading.................................................................. 46
Using the Twin Needle Mode............................................... 49
Using Threads that Unwind Quickly .................................... 51
CHANGING THE PRESSER FOOT ...................... 53
Removing the Presser Foot ................................................... 53
Attaching the Presser Foot .................................................... 53
Attaching the Presser Foot with the Included Adapter........... 53
CHANGING THE NEEDLE.................................. 55
ABOUT THE NEEDLE AND FABRIC ................... 56
About the Needle ................................................................. 56
Fabric/Thread/Needle Combinations .................................... 57
BEFORE EMBROIDERING .................................. 58
Embroidery Step by Step....................................................... 58
Attaching the Embroidery Foot “W” ..................................... 59
Using the Optional Embroidery Foot “W+” with LED
Pointer ................................................................................. 60
Attaching the Embroidery Unit ............................................. 62
USING FUNCTIONS BY CONNECTING THE
ACCESSORY TO THE MACHINE ........................ 65
Using USB Media or Embroidery Card Reader/
USB Card Writer Module* .................................................... 65
Connecting the Machine to the Computer ............................ 65
Using a USB Mouse ............................................................. 66
Using the Optional Dual Feed Foot ...................................... 67
S Sewing
Chapter1 Sewing Basics 2
SEWING............................................................... 3
Sewing a Stitch ...................................................................... 3
Sewing Reinforcement Stitches .............................................. 5
Automatic Reinforcement Stitching........................................ 5
Sewing Curves....................................................................... 7
Changing Sewing Direction ................................................... 7
Sewing Heavyweight Fabrics ................................................. 7
Sewing Hook-and-Loop Fastener ........................................... 8
Sewing Lightweight Fabrics.................................................... 9
Sewing Stretch Fabrics........................................................... 9
STITCH SETTINGS ............................................. 10
Setting the Stitch Width ....................................................... 10
Setting the Stitch Length....................................................... 10
Setting the “L/R SHIFT”........................................................ 11
Setting the Thread Tension................................................... 12
USEFUL FUNCTIONS ........................................ 14
Automatic Thread Cutting.................................................... 14
Using the Knee Lifter ........................................................... 15
Pivoting ............................................................................... 15
Automatic Fabric Sensor System (Automatic Presser Foot
Pressure).............................................................................. 17
Needle Position – Stitch Placement...................................... 18
Locking the Screen .............................................................. 18
Chapter2 Utility Stitches 20
SELECTING UTILITY STITCHES ......................... 21
Selecting a Stitch ................................................................. 21
Saving Your Stitch Settings................................................... 22
SEWING THE STITCHES .................................... 24
Straight Stitches ................................................................... 24
Dart Seam............................................................................ 28
Gathering ............................................................................ 29
Flat Fell Seam ...................................................................... 29
Pintuck ................................................................................ 30
Zigzag Stitches..................................................................... 31
Elastic Zigzag Stitches.......................................................... 33
Overcasting ......................................................................... 33
Quilting............................................................................... 35
Blind Hem Stitches .............................................................. 45
Appliqué.............................................................................. 48
Shelltuck Stitches................................................................. 49
Scallop Stitches.................................................................... 50
Crazy Quilting..................................................................... 50
Smocking Stitches................................................................ 51
Fagoting............................................................................... 52
Tape or Elastic Attaching ..................................................... 52
Heirloom............................................................................. 53
One-step Buttonholes .......................................................... 55
Darning ............................................................................... 58
Bar Tacks............................................................................. 59
Button Sewing ..................................................................... 61
Eyelet................................................................................... 62
Multi-directional Sewing
(Straight Stitch and Zigzag Stitch)......................................... 63
Zipper Insertion................................................................... 64
STITCH SETTING CHART .................................. 67
B-6
CONTENTS
Chapter3 Character/Decorative Stitches 76
SELECTING STITCH PATTERNS ......................... 77
Selecting Decorative Stitch Patterns/7mm Decorative Stitch
Patterns/Satin Stitch Patterns/7mm Satin Stitch
Patterns/Cross Stitch/Utility Decorative Stitch Patterns.......... 78
Characters............................................................................ 78
SEWING STITCH PATTERNS .............................. 81
Sewing Attractive Finishes.................................................... 81
Basic Sewing........................................................................ 81
Making Adjustments ............................................................ 82
EDITING STITCH PATTERNS ............................. 84
Changing the Size................................................................ 86
Changing the Length (for 7mm Satin Stitch Patterns Only).... 86
Creating a Vertical Mirror Image .......................................... 86
Creating a Horizontal Mirror Image ..................................... 86
Sewing a Pattern Continuously............................................. 86
Changing Thread Density (for Satin Stitch Patterns Only) ..... 87
Returning to the Beginning of the Pattern ............................. 87
Checking the Image ............................................................. 88
COMBINING STITCH PATTERNS ...................... 89
Before Combining................................................................ 89
Combining Various Stitch Patterns ....................................... 89
Combining Large and Small Stitch Patterns .......................... 90
Combining Horizontal Mirror Image Stitch Patterns ............. 91
Combining Stitch Patterns of Different Length...................... 91
Making Step Stitch Patterns
(for 7mm Satin Stitch Patterns Only)..................................... 92
USING THE MEMORY FUNCTION.................... 94
Stitch Data Precautions ........................................................ 94
Saving Stitch Patterns in the Machine’s Memory .................. 95
Saving Stitch Patterns to USB Media .................................... 96
Saving Stitch Patterns in the Computer................................. 97
Retrieving Stitch Patterns from the Machine’s Memory......... 98
Recalling from USB Media................................................... 99
Recalling from the Computer ............................................. 100
Chapter4 MY CUSTOM STITCH 102
DESIGNING A STITCH .................................... 103
ENTERING STITCH DATA................................ 105
USING STORED CUSTOM STITCHES .............. 110
Storing Custom Stitches in Your List................................... 110
Retrieving Stored Stitches................................................... 111
E Embroidering
Chapter1 Embroidery 2
SELECTING PATTERNS......................................... 3
Selecting Embroidery Patterns/Brother “Exclusives”/Floral
Alphabet/Bobbin Work Patterns ............................................. 4
Selecting Character Patterns................................................... 5
Selecting Frame Patterns ........................................................ 7
Selecting Patterns from Embroidery Cards.............................. 7
Selecting Patterns from USB Media/Computer........................ 8
VIEWING THE EMBROIDERING SCREEN............ 9
PREPARING THE FABRIC ................................... 11
Attaching Iron-on Stabilizers (Backing) to the Fabric ............ 11
Hooping the Fabric in the Embroidery Frame ....................... 13
Embroidering Small Fabrics or Fabric Edges ......................... 16
ATTACHING THE EMBROIDERY FRAME........... 17
CONFIRMING THE PATTERN POSITION.......... 19
Checking the Pattern Position .............................................. 19
Previewing the Completed Pattern ....................................... 20
SEWING AN EMBROIDERY PATTERN ............... 21
Embroidery Attractive Finishes ............................................. 21
Sewing Embroidery Patterns................................................. 22
Sewing Embroidery Patterns Which Use Appliqué ............... 23
ADJUSTMENTS DURING THE EMBROIDERY
PROCESS............................................................. 26
If the Bobbin Runs Out of Thread ......................................... 26
If the Thread Breaks During Sewing...................................... 27
Restarting from the Beginning............................................... 28
Resuming Embroidery After Turning Off the Power .............. 28
MAKING EMBROIDERY ADJUSTMENTS........... 30
Adjusting Thread Tension..................................................... 30
Adjusting the Bobbin Case (with No Color on the Screw) ..... 31
Using the Automatic Thread Cutting Function
(END COLOR TRIM) ............................................................ 32
Using the Thread Trimming Function
(JUMP STITCH TRIM)........................................................... 32
Adjusting the Embroidery Speed........................................... 33
Changing the Thread Color Display...................................... 34
Changing the “Embroidery Frame Display” .......................... 35
REVISING THE PATTERN................................... 36
Moving the Pattern ............................................................... 36
Aligning the Pattern and the Needle ..................................... 36
Changing the Size of the Pattern........................................... 37
Rotating the Pattern .............................................................. 38
Creating a Horizontal Mirror Image...................................... 39
Enlarging the Editing Screen ................................................. 39
Changing the Density (Alphabet Character and Frame
Patterns Only) ...................................................................... 40
Changing the Colors of Alphabet Character Patterns............. 40
Embroidering Linked Characters........................................... 41
Uninterrupted Embroidering (Monochrome - Using a Single
Color)................................................................................... 43
USING THE MEMORY FUNCTION ................... 44
Embroidery Data Precautions ............................................... 44
Saving Embroidery Patterns in the Machine’s Memory ......... 45
Saving Embroidery Patterns to USB Media............................ 46
Saving Embroidery Patterns in the Computer........................ 47
Retrieving Patterns from the Machine’s Memory................... 48
Recalling from USB Media ................................................... 49
Recalling from the Computer................................................ 50
EMBROIDERY APPLICATIONS .......................... 51
Using a Frame Pattern to Make an Appliqué (1).................... 51
Using a Frame Pattern to Make an Appliqué (2).................... 52
Sewing Split Embroidery Patterns ......................................... 53
Chapter2 Embroidery Edit 56
EXPLANATION OF FUNCTIONS....................... 57
SELECTING PATTERNS TO EDIT ....................... 58
Selecting Embroidery Patterns/Brother “Exclusives”/Floral
Alphabet Patterns/Frame/Bobbin Work Patterns.................... 59
Selecting Alphabet Character Patterns .................................. 59
EDITING PATTERNS .......................................... 61
Moving the Pattern ............................................................... 63
Rotating the Pattern .............................................................. 63
Changing the Size of the Pattern........................................... 63
Deleting the Pattern.............................................................. 63
Displaying Patterns in the Screen Magnified by 200% .......... 63
Changing the Configuration of Character Patterns ................ 64
Changing Character Spacing ................................................ 64
Reducing Character Spacing................................................. 65
Separating Combined Character Patterns.............................. 65
Changing the Color of Each Alphabet Character in a
Pattern.................................................................................. 66
Embroidering Linked Characters........................................... 67
Changing the Thread Color .................................................. 67
Creating a Custom Thread Table .......................................... 68
Choosing a Color from the Custom Thread Table ................. 71
Designing Repeated Patterns ................................................ 72
Embroidering the Pattern Repeatedly.................................... 76
Duplicating a Pattern............................................................ 78
After Editing ......................................................................... 79
COMBINING PATTERNS ................................... 80
Editing Combined Patterns ................................................... 80
Sewing Combined Patterns................................................... 83
B-7
CONTENTS
VARIOUS EMBROIDERING FUNCTIONS.......... 84
Uninterrupted Embroidering (Monochrome - Using a Single
Color)................................................................................... 84
Basting Embroidery .............................................................. 84
USING THE MEMORY FUNCTION.................... 85
A Appendix
Chapter1 How to Create Bobbin Work 2
ABOUT BOBBIN WORK ...................................... 3
PREPARING FOR BOBBIN WORK ....................... 3
Required Materials ................................................................. 3
Upper Threading.................................................................... 4
Preparing the Bobbin Thread .................................................. 5
CREATING BOBBIN WORK (SEWING)................ 9
Positioning the Fabric and Sewing.......................................... 9
Bobbin Work Free Motion Sewing........................................ 11
CREATING BOBBIN WORK (EMBROIDERY) ..... 12
Selecting the Pattern............................................................. 12
Start Embroidering................................................................ 14
ADJUSTING THE THREAD TENSION ................ 16
TROUBLESHOOTING ........................................ 17
Chapter2 Maintenance and
Troubleshooting 18
CARE AND MAINTENANCE............................... 19
Restrictions on oiling............................................................ 19
Precautions on storing the machine...................................... 19
Cleaning the LCD Screen ..................................................... 19
Cleaning the Machine Casing............................................... 19
Cleaning the Race ................................................................ 19
Cleaning the Cutter in the Bobbin Case Area........................ 21
About the Maintenance Message .......................................... 21
ADJUSTING THE SCREEN .................................. 22
Adjusting the Brightness of the Screen Display ..................... 22
Touch Panel is Malfunctioning ............................................. 22
TROUBLESHOOTING ........................................ 23
Frequent troubleshooting topics ........................................... 23
Upper thread tightened up ................................................... 23
Tangled thread on wrong side of fabric ................................ 24
Incorrect thread tension........................................................ 26
Fabric is caught in the machine and cannot be removed ...... 27
List of Symptoms .................................................................. 30
ERROR MESSAGES ............................................. 34
SPECIFICATIONS ............................................... 37
UPGRADING YOUR MACHINE’S
SOFTWARE......................................................... 38
Upgrade Procedure Using USB Media.................................. 38
Upgrade Procedure Using Computer.................................... 39
INDEX ................................................................ 40
B-8
NAMES OF MACHINE PARTS AND THEIR FUNCTIONS
NAMES OF MACHINE PARTS AND THEIR FUNCTIONS
The names of the various parts of the sewing machine and their functions are described below. Before
using the sewing machine, carefully read these descriptions to learn the names of the machine parts.
Machine
■ Front View
a Top cover
Open the top cover to thread the machine and wind the
bobbin.
b Pre-tension disk
Pass the thread around the pre-tension disk when winding the
bobbin thread. (page B-38)
c Thread guide for bobbin winding
Pass the thread through this thread guide when winding the
bobbin thread. (page B-38)
d Spool pin
Place a spool of thread on the spool pin. (page B-46)
e Spool cap
Use the spool cap to hold the spool of thread in place.
(page B-46)
f Supplemental spool pin
Use this spool pin to wind the bobbin thread, or to sew with the
twin needle. (page B-38, B-49)
g Bobbin winder
Use the bobbin winder when winding the bobbin. (page B-38)
h LCD (liquid crystal display)
Settings for the selected stitch and error messages appear in
the LCD. (page B-22)
i Speaker
j Knee lifter
Use the knee lifter to raise and lower the presser foot.
(page S-15)
k Knee lifter slot
Insert the knee lifter into the slot. (page S-15)
l Operation buttons (7 buttons) and sewing speed
controller
Use these buttons and the slide to operate the sewing
machine. (page B-11)
m Flat bed attachment with accessory compartment
Store presser feet and bobbins in the accessory compartment
of the flat bed attachment. When sewing cylindrical pieces,
remove the flat bed attachment. (page B-12)
n Thread cutter
Pass the threads through the thread cutter to cut them.
(page B-48)
o Thread guide plate
Pass the thread around the thread guide plate when threading
upper thread. (page B-46)
■ Right-side/Rear View
a Connector for the optional presser foot
Connect the dual feed foot or embroidery foot with LED
pointer. (page B-60, B-67)
b Handle
Carry the sewing machine by its handle when transporting the
machine.
c Presser foot lever
Raise and lower the presser foot lever to raise and lower the
presser foot. (page B-53)
d Air vent
The air vent allows the air surrounding the motor to circulate.
Do not cover the air vent while the sewing machine is being
used.
e Main power switch
Use the main power switch to turn the sewing machine ON and
OFF. (page B-19)
f Foot controller
Depress the foot controller to control the speed of the machine.
(page S-4)
g Power cord receptacle
Insert the power cord into the machine receptacle. (page B-19)
h Foot controller jack
Insert the foot controller plug into its jack on the machine.
(page S-4)
i USB port for computer
In order to import/export patterns between a computer and the
machine, plug the USB cable into the USB port. (page B-65,
S-97, E-47)
j USB port for mouse/media (USB 2.0)
In order to send patterns from/to USB media, plug the USB
media directly into the USB port. (page B-65, S-96, E-46)
Connect the USB mouse to operate with mouse. (page B-66)
k Handwheel
Rotate the handwheel toward you (counterclockwise) to raise
and lower the needle. The wheel should be turned toward the
front of the machine.
B-9
NAMES OF MACHINE PARTS AND THEIR FUNCTIONS
Needle and Presser Foot Section
a Buttonhole lever
The buttonhole lever is used with the one-step buttonhole foot
to create buttonholes. (page S-55)
b Presser foot holder screw
Use the presser foot holder screw to hold the presser foot in
place. (page B-53, B-59)
c Presser foot holder
The presser foot is attached to the presser foot holder.
(page B-53)
d Presser foot
The presser foot consistently applies pressure to the fabric as
sewing takes place. Attach the appropriate presser foot for the
selected stitch. (page B-53)
e Feed dogs
The feed dogs feed the fabric in the sewing direction.
f Bobbin cover
Open the bobbin cover to set the bobbin. (page B-43, S-32)
g Needle plate cover
Remove the needle plate cover to clean the race. (page S-26,
E-22)
h Needle plate
The needle plate is marked with guides to help sew straight
seams. (page S-26)
i Needle bar thread guide
Pass the upper thread through the needle bar thread guide.
(page B-46)
j Needle clamp screw
Use the needle clamp screw to hold the needle in place.
(page B-53)
Measurements on the needle plate, bobbin cover
(with mark) and needle plate cover
The measurements on the bobbin cover are
references for patterns with a middle (center)
needle position. The measurements on the needle
plate and the needle plate cover are references for
stitches with a left needle position.
a For stitches with a middle (center) needle position
b For stitches with a left needle position
c Left needle position on the needle plate <inch>
d Left needle position on the needle plate <cm>
e Middle (center) needle position on the bobbin cover
(with mark) <inch>
f Left needle position on the needle plate cover
<inch>
B-10
NAMES OF MACHINE PARTS AND THEIR FUNCTIONS
CAUTION
CAUTION
Embroidery Unit
a Carriage
The carriage moves the embroidery frame automatically when
embroidering. (page B-62)
b Release button (located under the embroidery unit)
Press the release button to remove the embroidery unit.
(page B-62)
c Embroidery frame holder
Insert the embroidery frame into the embroidery frame holder
to hold the frame in place. (page E-17)
d Frame-securing lever
Press the frame-securing lever down to secure the embroidery
frame. (page E-17)
e Embroidery unit connection
Insert the embroidery unit connection into the connection port
when attaching the embroidery unit. (page B-62)
• Before inserting or removing the embroidery
unit, turn the main power to OFF.
• After the embroidery frame is set in the frame
holder, be sure the frame-securing lever is
correctly lowered.
Operation Buttons
a “Start/Stop” button
Press this button and the machine will sew a few stitches at a
slow speed and then begin sewing at the speed set by the
sewing speed controller. Press the button again to stop the
machine. Hold the button in to sew at the machine’s slowest
speed. The button changes color according to the machine’s
operation mode.
Green: The machine is ready to sew or is sewing.
Red: The machine cannot sew.
b “Reverse Stitch” button
For straight, zigzag, and elastic zigzag stitch patterns that take
reverse stitches, the machine will sew reverse stitches at low
speed only while holding down the “Reverse Stitch” button.
The stitches are sewn in the opposite position.
For other stitches, use this button to sew reinforcement
stitches at the beginning and end of sewing. Press and hold
this button, and the machine sews 3 stitches in the same spot
and stops automatically. (see page S-5)
c “Reinforcement Stitch” button
Use this button to sew a single stitch repeatedly and tie-off.
For character/decorative stitches, press this button to end with
a full stitch instead of at a mid-point. The LED light beside this
button lights up while the machine is sewing a full motif, and
automatically turns off when the sewing is stopped. (see page
S-5)
d “Needle Position” button
Use this button when changing sewing direction or for detailed
sewing in small areas. Press this button to raise or lower the
needle position. With this button, you can lower and raise the
needle to sew a single stitch.
e “Thread Cutter” button
Press this button after sewing to automatically trim the excess
thread.
f “Presser Foot Lifter” button
Press this button to lower the presser foot and apply pressure
to the fabric. Press this button again to raise the presser foot.
g Sewing Speed controller
Use this controller to adjust the sewing speed. Move the slide
to the left to sew at slower speeds. Move the slide to the right
to sew at higher speeds. Beginners should sew at a slow
speed.
h “Automatic Threading” button
Use this button to automatically thread the needle.
• Do not press the thread cutter button after the
threads have been cut. The needle may break
and threads may become tangled, or damage
to the machine may occur.
B-11
NAMES OF MACHINE PARTS AND THEIR FUNCTIONS
Using the Flat Bed Attachment
Pull the top of the flat bed attachment to open the
accessory compartment.
A presser foot storage tray is stored in the accessory
compartment of the flat bed attachment.
a Storage space of the flat bed attachment
b Presser foot storage space of the flat bed
attachment
c Presser foot storage tray
There are also storage spaces for optional presser
feet, such as the vertical stitch alignment foot “V”.
B-12
NAMES OF MACHINE PARTS AND THEIR FUNCTIONS
75/11 2 needles
90/14 2 needles
90/14 2 needles:
Ball point needle (gold colored)
2.0/11 needle
75/11 2 needles:
Ball point needle
for embroidery
HAX130EBBR
Included Accessories
12345 67
8 9 101112 1314
15 16 17 18 19 20 21 22
23 24 25 26 27 28 29 30
31 32 33 34 35 36 37 38
39 40 41 42 43 44 45 46
47 48 49
B-13
NAMES OF MACHINE PARTS AND THEIR FUNCTIONS
Memo
No. Part Name
1 Zigzag foot “J” (on machine) XF3022-001
2 Monogramming foot “N” X53840-351
3 Overcasting foot “G” XC3098-051
4 Zipper foot “I” X59370-051
5 Buttonhole foot “A” X57789-251
6 Blind stitch foot “R” X56409-051
7 Button fitting foot “M” 130489-001
8 Embroidery foot “W” XF4012-001
9 Free motion open toe quilting
foot “O”
10 Adapter XF3613-001
11 Screw (small) XA4813-051
12
Needle set
13
Twin needle
14
Ball point needle set
15 Bobbin × 10
(One is on machine.)
16 Seam ripper XF4967-001
17 Scissors XC1807-121
18 Cleaning brush X59476-051
19 Eyelet punch XZ5051-001
20 Screwdriver (small) X55468-051
21 Screwdriver (large) XC4237-021
22 Disc-shaped screwdriver XC1074-051
23 Vertical spool pin XC8619-052
24 Spool cap (small) 130013-154
25 Spool cap (medium) × 2
(One is on machine.)
26 Spool cap (large) 130012-054
27 Spool cap (special) XA5752-121
28 Bobbin clip × 10 XE3060-001
29 Spool felt (on machine) X57045-051
30 Spool net × 2 XA5523-050
31 Embroidery needle plate
cover
32 Touch pen (stylus) XA9940-051
33 Knee lifter XA6941-052
34 USB cable XD0745-051
35 Alternate bobbin case
(no color on the screw)
36 Bobbin case (gray, for bobbin
work)
37 Cord guide bobbin cover
(with single hole)
38 Bobbin cover (with mark) XF0750-101
39 Bobbin cover (on machine) XE8992-101
40 Foot controller XD0501-151(EU area)
41 Embroidery frame set
(extra large)
H 30 cm × W 18 cm
(H 12 inches × W 7 inches)
42 Embroidery bobbin thread SA-EBT XC6283-001
43 Stabilizer material SA519 BM3:
44 Grid sheet set SA507 GS3:
45 Chalk pencil XE8568-001
46 Dust cover VM5100 : XF4569-001
47 Accessory bag XC4487-021
48 Operation manual This manual
49 Quick Reference Guide XF6503-001 XF3617-001
*1
*2
*3
Part Code
Americas Others
XF4873-001
X58358-051
X59296-151
XD0705-051
SA156 SFB:
XC8816-051 (other area)
SA440 EF76:
V5 : XF4113-001
XA5539-151
X55260-153
XE5131-001
XC8167-551
XE8298-001
XE8991-101
XC8482-152
XE0806-001
X81277-151
*1 75/11 2 needles
90/14 2 needles
90/14 2 needles: Ball point needle (gold colored)
*2 2.0/11 needle
*3 75/11 2 needles:
Ball point needle for embroidery
HAX130EBBR
• Foot controller: Model T
This foot controller can be used on the
machine with product code 882-C50. The
product code is mentioned on the machine
rating plate.
• Always use accessories recommended for
this machine.
• Placing bobbin clips on bobbins helps
prevent the thread from unwinding from the
bobbin. In addition, snapping bobbin clips
together allows the bobbins to be
conveniently stored and prevents them from
rolling around if they are dropped.
B-14
NAMES OF MACHINE PARTS AND THEIR FUNCTIONS
Accessories that are Included in Some Countries or Regions
If these accessories are not included with your machine, these are available as optional accessories.
123
45
No. Part Name
1 Straight stitch foot SA167 F042N:
2 1/4” quilting foot with guide SA185 F057:
3 Straight stitch needle plate XF3076-001
4 Embroidery frame set
(medium) H 10 cm × W 10 cm
(H 4 inches × W 4 inches)
5 Embroidery frame set (large)
H 18 cm × W 13 cm
(H 7 inches × W 5 inches)
Part Code
Americas Others
XC1973-052
XC7416-252
SA438 EF74:
SA439 EF75:
XC8480-152
XC8481-152
Options
The following are available as optional accessories to be purchased separately from your authorized Brother dealer.
1234 56 7 8
91011121314 1516
17 18 19 20 21 22 23
24
B-15
NAMES OF MACHINE PARTS AND THEIR FUNCTIONS
Memo
Note
No. Part Name
1 Multi-function foot controller SAMFFC
2 Embroidery frame set (small)
H 2 cm × W 6 cm
(H 1 inch × W 2-1/2 inches)
3 Square embroidery frame
H 15 cm x W 15 cm
(H 6 inches x W 6 inches)
4 Dual feed foot SA196
5 Open toe for dual feed foot SA195 F070:
6 Embroidery foot “W+” with
LED pointer
7 Border embroidery frame
H 30 cm x W 10 cm (H 12
inches x W 4 inches)
8 10 spool stand SA561
9 King spool thread stand SA562
10 Wide table SAWT6200D
11 Embroidery card Reader SAECRI
12 Embroidery card –
13 Stabilizer material SA519 BM3:
Water soluble stabilizer SA520 BM5:
14 Seam guide SA538 SG1:
15 Walking foot SA140 F033N:
16 Side cutter foot SA177 F054:
17 Free motion quilting foot “C” XF4737-001
18
Free motion echo quilting foot “E”
19 Free-motion quilting foot SA129 F005N:
20 Circular attachment SACIRC1 CIRC1:
21 Stitch in the ditch foot SA191 F065:
22 Vertical stitching alignment
foot “V”
23 USB mouse XE5334-101
24 Free motion guide grip SAFMGRIP FMG2:
SABF6200D1
SABF6200D1C
SAWT6200DC
Part Code
Americas Others
(USA)
SAMFFCC
(Canada)
SA437 EF73:
SA448
(USA)
SA448C
(Canada)
(USA)
SA196C
(Canada)
SA197
(USA)
SA197C
(Canada)
(USA)
(Canada)
(USA)
SA561C
(Canada)
(USA)
SA562C
(Canada)
(USA)
(Canada)
XE0766-001
SA189 F063:
MFFC1:
XF4159-001
MFFC1OC:
XF4471-001
(Australia)
XC8479-152
SEF150:
XF4163-001
DF1:
XF4166-001
(EU area)
DF1AP:
XF6843-001
(other area)
XF6096-001
FLED1:
XF4168-001
(EU area)
FLED1AP:
XF6845-001
(other area)
BF3:
XF4170-001
TS5:
XF4175-001
TS6:
XF4180-001
WT10:
XF4184-001
XE0806-001
XE0615-001
XC8483-052
XC2214-052
XC3879-152
XC1948-052
XE3527-001
XF2339-001
XE5224-001
XF6266-001
(EU area)
FMG2AP:
XF6267-001
(other area)
• All specifications are correct at the time of
printing. Please be aware that some
specifications may change without notice.
• Embroidery cards purchased in foreign
countries may not work with your machine.
• Visit your dealer or nearest authorized
Brother dealer for a complete listing of
optional accessories and embroidery cards
available for your machine.
B-16
Basic
operations
This section provides details on the initial setup procedures as well as descriptions of this
machine’s more useful functions.
Page number starts with “B” in this section.
Chapter1 Getting Ready .......................................................B-18
B Basic operations
Chapter 1
Getting Ready
TURNING THE MACHINE ON/OFF ........................19
Setting Your Machine for the First Time ...................................20
LCD SCREEN............................................................22
■ Home Page Screen ................................................................... 22
■ Utility Stitch Screen .................................................................23
■ Key Functions........................................................................... 24
Using the Machine Setting Mode Key ......................................26
■ Selecting the “Eco Mode” or “Shutoff Support Mode”............. 30
■ Changing the Pointer Shape When a USB Mouse Is Used ........ 30
■ Selecting the Initial Screen Display.......................................... 30
■ Choosing the Display Language................................................ 31
■ Changing the Background Colors of the Embroidery
Patterns.................................................................................... 31
■ Specifying the Size of Pattern Thumbnails ...............................32
■ Saving a Settings Screen Image to USB Media.......................... 33
Using the Sewing Machine Help Key .......................................34
Using the Operation Guide Function ........................................35
Using the Sewing Guide Function .............................................36
Using the Pattern Explanation Function ....................................37
LOWER THREADING ..............................................38
Winding the Bobbin..................................................................38
■ Using the Supplemental Spool Pin............................................38
■ Using the Spool Pin.................................................................. 41
■ Untangling Thread from Beneath the Bobbin Winder Seat ...... 42
Setting the Bobbin ....................................................................43
Pulling Up the Bobbin Thread................................................... 45
UPPER THREADING................................................46
Upper Threading....................................................................... 46
Using the Twin Needle Mode ..................................................49
Using Threads that Unwind Quickly .........................................51
■ Using the Spool Net .................................................................51
■ Using the Vertical Spool Pin ....................................................52
CHANGING THE PRESSER FOOT............................53
Removing the Presser Foot........................................................ 53
Attaching the Presser Foot ........................................................ 53
Attaching the Presser Foot with the Included Adapter.............. 53
■ Attaching the Walking foot ...................................................... 54
CHANGING THE NEEDLE.......................................55
USING FUNCTIONS BY CONNECTING THE
ACCESSORY TO THE MACHINE .............................65
Using USB Media or Embroidery Card Reader/
USB Card Writer Module* ....................................................... 65
Connecting the Machine to the Computer ............................... 65
Using a USB Mouse.................................................................. 66
■ Clicking a Key ...........................................................................66
■ Changing Pages.........................................................................66
Using the Optional Dual Feed Foot.......................................... 67
■ Attaching the Dual Feed Foot ...................................................67
■ Attaching/detaching toe ...........................................................67
■ Using the Dual Feed Position Lever ..........................................68
■ Adjusting the Amount of Fabric Feeding of the Dual Feed
Foot ..........................................................................................68
ABOUT THE NEEDLE AND FABRIC......................... 56
About the Needle...................................................................... 56
Fabric/Thread/Needle Combinations ........................................57
BEFORE EMBROIDERING........................................58
Embroidery Step by Step ..........................................................58
Attaching the Embroidery Foot “W” .........................................59
Using the Optional Embroidery Foot “W+” with LED
Pointer ...................................................................................... 60
■ Attaching the Embroidery Foot “W+” with LED Pointer.......... 60
■ Checking the Needle Drop Point With the Embroidery Foot
“W+” with LED Pointer............................................................ 61
■ Adjusting the LED Pointer ........................................................ 61
■ Adjusting the Brightness of the LED Pointer............................. 62
Attaching the Embroidery Unit .................................................62
■ About the Embroidery Unit...................................................... 62
■ Removing the Embroidery Unit ............................................... 63
TURNING THE MACHINE ON/OFF
WARNING
CAUTION
TURNING THE MACHINE ON/OFF
B
• Use only regular household electricity for the power source. Using other power sources may result in fire,
electric shock, or damage to the machine.
• Make sure that the plugs on the power cord are firmly inserted into the electrical outlet and the power
cord receptacle on the machine.
• Do not insert the plug on the power cord into an electrical outlet that is in poor condition.
• Turn the main power to OFF and remove the plug in the following circumstances:
When you are away from the machine
After using the machine
When the power fails during use
When the machine does not operate correctly due to a bad connection or a disconnection
During electrical storms
• Use only the power cord included with this machine.
• Do not use extension cords or multi-plug adapters with many other appliances plugged in to them. Fire or
electric shock may result.
• Do not touch the plug with wet hands. Electric shock may result.
• When unplugging the machine, always turn the main power to OFF first. Always grasp the plug to remove
it from the outlet. Pulling on the cord may damage the cord, or lead to fire or electric shock.
• Do not allow the power cord to be cut, damaged, modified, forcefully bent, pulled, twisted, or bundled.
Do not place heavy objects on the cord. Do not subject the cord to heat. These things may damage the
cord, or cause fire or electric shock. If the cord or plug is damaged, take the machine to your authorized
dealer for repairs before continuing use.
• Unplug the power cord if the machine is not to be used for a long period of time. Otherwise, a fire may
result.
• When leaving the machine unattended, either the main switch of the machine should be turned to OFF or
the plug must be removed from the socket-outlet.
• When servicing the machine or when removing covers, the machine must be unplugged.
• For USA only
This appliance has a polarized plug (one blade wider than the other). To reduce the risk of electrical
shock, this plug is intended to fit in a polarized outlet only one way.
If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified
electrician to install the proper outlet. Do not modify the plug in any way.
1
Getting Ready
Basic operations B-19
TURNING THE MACHINE ON/OFF
Note
Memo
CAUTION
Memo
Insert the power supply cord into the power
a
cord receptacle, then insert the plug into a
wall outlet.
a Main power switch
b Power supply cord
Turn the main power switch to “I” to turn
b
on the machine.
Turn the main power switch to “O” to turn
d
off the machine.
• If the machine is turned off in the middle of
sewing in the “Sewing” function, the
operation will not continued after turning the
power on again.
Setting Your Machine for the First
Time
When you first turn on the machine, set the
language and time/date to your language and local
time/date. Follow the procedure below when the
settings screen appears automatically.
Press and to set your local language.
a
a OFF
b ON
• When the straight stitch needle plate is on
the machine, the needle will automatically
move to the middle position.
• When the machine is turned on, the needle
and the feed dogs will make sound when
they move; this is not a malfunction.
When the machine is turned on, the
c
opening movie is played. Touch anywhere
on the screen to display the Home page
screen.
• Only touch the screen with your finger or the
included touch pen. Do not use a sharp pencil,
screwdriver, or other hard or sharp object. It is
not necessary to press hard on the screen.
Pressing too hard or using a sharp object may
damage the screen.
Press .
b
The message screen, confirming if you want
c
to set time/date, appears. To set the
time/date, press ; to cancel the
setting, press .
→ The screen to set time/date appears.
B-20
Press or to set time/date.
Note
dc
b
a
d
a Press to display the time on the screen.
b Set the year (YYYY), month (MM) and date (DD).
c Select whether 24h or 12h setting to display.
d Set the current time.
TURNING THE MACHINE ON/OFF
B
1
Getting Ready
Press to start using your machine.
e
→ The clock starts from 0 second of the time you set.
• The time/date you set may be cleared, if
you don’t turn on the machine for a certain
period.
Basic operations B-21
LCD SCREEN
CAUTION
b
c
a
LCD SCREEN
• Only touch the screen with your finger or the included touch pen. Do not use a sharp pencil, screwdriver,
or other hard or sharp object. It is not necessary to press hard on the screen. Pressing too hard or using a
sharp object may damage the screen.
■ Home Page Screen
No. Display Key Name Explanation Page
a “Sewing” key Press this key to sew utility stitches or character or decorative stitch
patterns.
b “Embroidery” key Attach the embroidery unit and press this key to embroider patterns. E-3
c “Embroidery Edit” key Press this key to combine embroidery patterns. With the “Embroidery
Edit” functions, you can also create original embroidery patterns or
frame patterns.
See the “Key
Functions” table.
B-24
E-57
B-22
LCD SCREEN
a
b
d
e
g
c
h
f
■ Utility Stitch Screen
Press a key with your finger to select the stitch pattern, to select a machine function, or to select an
operation indicated on the key. When the key display is light gray, the function is not currently available.
No. Display Key Name Explanation Page
a Needle position
setting display
Shows single or twin needle mode setting, and the needle stop
position.
–
B
1
Getting Ready
Single needle/down
position
Twin needle/down
position
b Selected stitch
display
c Presser foot display Shows the presser foot code. Attach the presser foot indicated in this
d Stitch preview Shows a preview of the selected stitch. When shown at 100%, the
e Pattern display size Shows the approximate size of the pattern selected.
f Stitch selection
screen
Shows the name and code number of the selected stitch. S-3
display before sewing.
stitch appears in the screen at nearly its actual size.
: Nearly the same size as the sewn pattern
: 1/2 the size of the sewn pattern
: 1/4 the size of the sewn pattern
* The actual size of the sewn pattern may differ depending on the type
of fabric and thread that is used.
Press the key for the pattern you want to sew. Use
Single needle/up position
Twin needle/up position
to change to different stitch groups.
B-53
S-21
S-21
S-21
g Page display Shows additional pages that can be displayed. –
h Scroll key
* All key functions of the LCD are explained in the “Key Functions” table on the following page.
Press or , to move one page at a time, or touch anywhere on
the bar to jump ahead for additional pages of stitches.
Basic operations B-23
–
LCD SCREEN
a db c
g
i
j
klm
q
n
o
p
e
f
h
s
r
■ Key Functions
No. Display Key Name Explanation Page
a “Utility Stitch” key Press this key to select a straight stitch, zigzag stitch, buttonhole, blind hem
b “Character/
Decorative Stitch” key
c Screen lock key Press this key to lock the screen. When the screen is locked, the various
d Home page screen
key
e Needle mode
selection key
(Single/Double)
f Image key Press this key to display an enlarged image of the selected stitch pattern. S-22
g Machine’s memory
key
h “L/R SHIFT” key Shows the tendency of Left/Right of the center line of the original zigzag stitch
stitch, or other stitches commonly used in garment construction.
Press this key to select character or decorative stitch patterns. S-77
settings, such as the stitch width and stitch length, are locked and cannot be
changed. Press this key again to unlock the settings.
Press this key anytime it is displayed to return to the home page screen and
select a different category - “Sewing”, “Embroidery” or “Embroidery Edit”.
Press this key to select twin needle sewing mode. The sewing mode changes
between single needle mode and twin needle mode each time you press the
key. If the key display is light gray, the selected stitch pattern cannot be sewn
in the twin needle mode.
Press this key to select from 3 memory functions; retrieving, storing or reset. S-22,
currently selected stitch pattern.
S-21
S-18
B-22
B-49
S-95,
S-97
S-11
i Thread tension key Shows the automatic thread tension setting of the currently selected stitch
pattern. You can use the plus and minus keys to change the thread tension
settings.
S-12
j Clock key Press this key to set the clock to your local time. B-20
k Presser foot/Needle
l Sewing machine help
m Machine setting
exchange key
key
mode key
n Stitch width and
stitch length key
B-24
Press this key before changing the needle, the presser foot, etc. This key locks
all key and button functions to prevent operation of the machine.
Press this key to see explanations on how to use the machine. B-34
B-53 to
Press this key to change the needle stop position, change the volume of
operation sound, adjust the pattern or screen, and change other machine
settings.
Shows the zigzag width and stitch length settings of the currently selected
stitch pattern. You can use the plus and minus keys to adjust the zigzag width
and stitch length settings.
B-55
B-26
S-10
LCD SCREEN
No. Display Key Name Explanation Page
o Mirror image key Press this key to create a mirror image of the selected stitch pattern. If the key
p Automatic thread
cutting key
q Automatic
reverse/reinforcement
stitch key
r Free motion mode
key
s Pivot key Press this key to select the pivot setting. When the pivot setting is selected,
display is light gray, a mirror image of the selected stitch pattern cannot be
sewn.
Press this key to set the automatic thread cutting function. Set the automatic
thread cutting function before sewing to have the machine automatically sew
reinforcement stitches at the beginning and end of sewing (depending on the
pattern, the machine may sew reverse stitches) and trim the threads after
sewing.
Press this key to use the automatic reverse/reinforcement stitching setting.
If you select this setting before sewing, the machine will automatically sew
reverse stitches or reinforcement stitches depending on the pattern, at the
beginning and end of sewing.
Press this key to enter free motion sewing mode.
The presser foot is raised to an appropriate height and the feed dog is lowered
for free motion quilting.
stopping the machine lowers the needle and slightly raises the presser foot
automatically. In addition, when sewing is restarted, the presser foot is
automatically lowered.
• If this key appears as , the pivot function cannot be used.
• Be sure the needle position on page B-27 of Machine Settings is set to the
down position.
S-21
S-14
S-5
S-40
S-15
B
1
Getting Ready
For additional operational information, refer to page reference number listed above.
Basic operations B-25
LCD SCREEN
Memo
a
b
c
d
e
l
f
h
g
l
i
j
k
l
Using the Machine Setting Mode Key
Press to change the default machine settings (needle stop position, embroidery speed, opening
display, etc.). To display the different settings screens, press for “Sewing settings”, for
“General settings” or for “Embroidery settings”.
• Press or next to the page numbers, to display a different settings screen.
Sewing settings
a Select whether to use the sewing speed controller to determine the zigzag width (see page S-39).
b Make adjustments to character or decorative stitch patterns (see page S-82).
c Adjust the presser foot height. (Select the height of the presser foot when the presser foot is raised.)
d Adjust the presser foot pressure. (The higher the number, the greater the pressure will be. Set the pressure at “3”
for normal sewing.) (see page S-17)
If the dual feed foot is installed and its roller is lowered, the pressure setting is fixed at “2” and cannot be changed.
e Fine tune the feed of the dual feed foot (see page B-67).
f Select whether “1-01 Straight stitch (Left)” or “1-03 Straight stitch (Middle)” is the utility stitch that is automatically
selected when the machine is turned on. (see page S-21)
g Select whether “Utility Stitch” or “Quilt Stitch” displayed first on the stitch selection screen when the “Sewing” is
selected.
h You can activate this setting after connecting the optional multi-function foot controller. (These settings are not
operable unless the optional multi-function foot controller is attached to the machine.)
i Change the height of the presser foot when sewing is stopped when the pivot setting is selected (see page S-15).
Adjust the presser foot to one of the three heights (3.2 mm, 5.0 mm and 7.5 mm). (see page S-15)
j Change the height of the presser foot when the machine is set to free motion sewing mode (see page S-40).
k When set to “ON”, the thickness of the fabric is automatically detected by an internal sensor while sewing. This
enables the fabric to be fed smoothly (see pages S-8 and S-17).
l Press to save the current settings screen image to USB media (see page B-33)
B-26
LCD SCREEN
CAUTION
a
d
e
b
c
g
h
f
General settings
a Select the needle stop position (the needle position when the machine is not operating) to be up or down. Select
the down position when using the pivot key. (see page S-15)
b Select the operation of the “Needle Position – Stitch Placement” button from the following two sequences (see
page S-18).
Each press of the “Needle Position – Stitch Placement” button:
“ON” – raises the needle, stops it at a nearly lowered position, then lowers it
“OFF” – raises the needle, then lowers it
c Change the shape of the pointer when a USB mouse is used (see page B-30).
d Turn the “Upper and Bobbin Thread Sensor” “ON” or “OFF”. If it is turned “OFF”, the machine can be used without
thread. (see page S-4, E-26)
B
1
Getting Ready
• If “Upper and Bobbin Thread Sensor” is set to “OFF”, remove the upper thread. If the machine is used
with the upper thread threaded, the machine will not be able to detect if the thread has become tangled.
Continuing to use the machine with tangled thread may cause damage.
e Change the speaker volume. Increase the number for louder volume, decrease for softer volume.
f Select to save the machine power by setting the “Eco Mode” or the “Shutoff Support Mode” (see page B-30).
g Select the initial screen that is displayed when the machine is turned on (see page B-30).
h Change the display language (see page B-31).
Basic operations B-27
LCD SCREEN
Memo
a
b
c
f
e
d
a Change the brightness of the needle area and work area lights.
b Change the screen display brightness (see page A-22).
c Display the service count which is a reminder to take your machine in for regular servicing. (Contact your
authorized dealer for details.)
d Display the total number of stitches sewn on this machine.
e The “No.” is the internal machine number for the embroidery and sewing machine.
f Display the program version. “Version 1” shows the program version of the LCD panel, “Version 2” shows the
program version of the machine.
• The latest version of software is installed in your machine. Check with your local authorized Brother
dealer or at “ http://solutions.brother.com
” for available updates (see page A-38).
B-28
Loading...