Brocade VDX 8770-8 User Manual

53-1002555-01
22 August 2012

Brocade VDX 8770-8

QuickStart Guide

®

53-1002555-01

*53-1002555-01*

Copyright © 2012, Brocade Communications Systems, Incorporated.

Brocade, Brocade Assurance, the B-wing symbol, BigIron, DCX, Fabric OS, FastIron, MLX, NetIron, SAN Health, ServerIron, TurboIron, VCS, and VDX
are registered trademarks, and AnyIO, Brocade One, CloudPlex, Effortless Networking, ICX, NET Health, OpenScript, and The Effortless Network
are trademarks of Brocade Communications Systems, Inc., in the United States and/or in other countries. Other brands, products, or service
names mentioned may be trademarks of their respective owners.

Notice: This document is for informational purposes only and does not set forth any warranty, expressed or implied, concerning any equipment,
equipment feature, or service offered or to be offered by Brocade. Brocade reserves the right to make changes to this document at any time,
without notice, and assumes no responsibility for its use. This informational document describes features that may not be currently available.
Contact a Brocade sales office for information on feature and product availability. Export of technical data contained in this document may
require an export license from the United States government.

The authors and Brocade Communications Systems, Inc. shall have no liability or responsibility to any person or entity with respect to any loss,
cost, liability, or damages arising from the information contained in this book or the computer programs that accompany it.

The product described by this document may contain “open source” software covered by the GNU General Public License or other open source
license agreements. To find out which open source software is included in Brocade products, view the licensing terms applicable to the open
source software, and obtain a copy of the programming source code, please visit
http://www.brocade.com/support/oscd.

Brocade Communications Systems, Incorporated

Corporate and Latin American Headquarters
Brocade Communications Systems, Inc.
130 Holger Way
San Jose, CA 95134
Tel: [phone]
Fax: [phone]
E-mail: [e-mail]

European Headquarters
Brocade Communications Switzerland Sàrl
Centre Swissair
Tour B - 4ème étage
29, Route de l'Aéroport
Case Postale 105
CH-1215 Genève 15
Switzerland
Tel: [phone]
Fax: [phone]
E-mail: [e-mail]

Asia-Pacific Headquarters
Brocade Communications Systems China HK, Ltd.
No. 1 Guanghua Road
Chao Yang District
Units 2718 and 2818
Beijing 100020, China
Tel: [phone]
Fax: [phone]
E-mail: [e-mail]

Asia-Pacific Headquarters
Brocade Communications Systems Co., Ltd. (Shenzhen WFOE)
Citic Plaza
No. 233 Tian He Road North
Unit 1308 – 13th Floor
Guangzhou, China
Tel: [phone]
Fax: [phone]
E-mail: [e-mail]

Document History

Document Title Publication

Number

Brocade VDX 8770-8 QuickStart Guide 53-1002555-01 New document. August 2012

Summary of
Changes

Publication
Date

2 of 34 Brocade VDX 8770-8 QuickStart Guide

Publication Number: 53-1002555-01

In this guide

•Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

•Safety notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

•Danger notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

•Caution notices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

•ESD precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

•Brocade VDX 8770-8, port side. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

•Brocade VDX 8770-8, nonport side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

•Items included with the Brocade VDX 8770-8 . . . . . . . . . . . . . . . . . . . . . . . . 9

•Preparing for the Brocade VDX 8770-8 installation. . . . . . . . . . . . . . . . . . . 10

•Unpacking and installing the Brocade VDX 8770-8. . . . . . . . . . . . . . . . . . . 13

•Port numbering. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

•Inserting a management module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

•Inserting a switch fabric module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

•Inserting a line card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

•Inserting power supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

•Providing power to the Brocade VDX 8770-8 . . . . . . . . . . . . . . . . . . . . . . . . 21

•Preparing to configure the Brocade VDX 8770-8. . . . . . . . . . . . . . . . . . . . . 22

•Establishing a serial connection to the Brocade VDX 8770-8. . . . . . . . . . . 23

•Logging in to the serial console port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

•Changing the RBridge ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

•Assigning permanent passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

•Configuring the IP addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

•Logging off the serial console port and disconnecting the serial cable. . . 26

•Establishing an Ethernet connection to the Brocade VDX 8770-8 . . . . . . . 26

•Customizing a host name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

•Customizing a chassis name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

•Setting the date and time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

•Determining installed software licenses. . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

•Saving your changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

•Verifying correct operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

•Backing up the configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

•Connecting network devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

•Installing transceivers and attaching cables . . . . . . . . . . . . . . . . . . . . . . . . 32

•Managing cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

•Creating Brocade inter-switch link trunks. . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Brocade VDX 8770-8 QuickStart Guide 3 of 34
Publication Number: 53-1002555-01

Introduction

DANGER

You can set up and install the Brocade VDX 8770-8 in the following ways:

• As a standalone unit on a flat surface

• In a four-post rack

• In a two-post telecommunications (Telco) rack

This manual describes how to set up the Brocade VDX 8770-8 as a standalone unit. For rack mount installation
instructions, refer to the manual that comes with the separately ordered rack kit.

Tab le 1 describes the main installation and setup tasks, the estimated time required for each, and the items

required to complete the task based on a fully populated Brocade VDX 8770-8 (384 10 GbE ports). Configurations
with fewer ports require less time. These time estimates assume a prepared installation site and appropriate power
and network connectivity.

The procedures in this manual are for qualified service personnel.

TABLE 1 Installation tasks, time, and items required

Installation task Time estimate Items required

Site preparation and unpacking Brocade
VDX 8770-8

Installing the rack mount kit 30 minutes

Mounting and securing Brocade VDX
8770-8 in the rack

Inserting modules and power supplies 5-10 minutes per

Installing power cables and powering on
the Brocade VDX 8770-8

Establishing a serial connection, logging on
to the Brocade VDX 8770-8, and
configuring the IP addresses

Installing an Ethernet cable, opening a
Telnet session, and configuring the
Brocade VDX 8770-8 date and time and
additional system parameters. Verify and
back up configuration.

30 minutes #2 Phillips screwdriver.

30 minutes

unit

20 minutes Power cables (provided in the Brocade VDX

20 minutes Serial cable (also called the console cable -

20 minutes Ethernet cabling (optional) for Telnet access.

Pallet jack.
Hydraulic lift or assisted lift, able to raise to a
minimum of 140 cm (55 in.), with a minimum
capacity of 113 kg (250 lb). A fully loaded
version of the Brocade VDX 8770-8 weighs

165.56 kg (365 lbs).

Refer to the proper rack mount kit instructions
for your specific rack..

Management modules, switch fabric modules,
line cards, power supplies (AC or DC).

8770-8 accessory kit).

provided in the accessory kit).
Workstation computer with a serial (console)
port or terminal server port and a terminal
emulator application (such as HyperTerminal).
Ethernet IP addresses for the Brocade VDX
8770-8 switch and for management modules:
total two or three addresses, depending on the
number of management modules installed.

Refer to the Brocade Network OS
Administrator’s Guide.

4 of 34 Brocade VDX 8770-8 QuickStart Guide

Publication Number: 53-1002555-01

CAUTION

CAUTION

NOTE

DANGER

TABLE 1 Installation tasks, time, and items required (Continued)

Installation task Time estimate Items required

Installing transceivers as needed 30-60 minutes Copper and optical transceivers and

direct-attach cables as needed.

Attaching cables, cable ties, and cable
guides

The Brocade VDX 8770-8 with DC power sources are intended for installation in restricted access areas
only. A restricted access area is a location where access can be gained only by service personnel through
the use of a special tool, lock and key, or other means of security, and is controlled by the authority
responsible for the location.

The Brocade VDX 8770-8 with AC power sources are intended for installation in restricted access areas
only. A restricted access area is a location where access can be gained only by service personnel through
the use of a special tool, lock and key, or other means of security.

2-3 hours Cables, cable ties, and cable comb.

Safety notices

When using this product, observe the danger, caution, and attention notices in this manual. The notices are
accompanied by symbols that represent the severity of the safety condition.

Translated safety notices are in the Brocade Product Safety Notices publication, which is on the CD-ROM that
accompanies this product.

The danger and caution notices are listed in numerical order based on their IDs, which are displayed in parentheses,
for example (D004), at the end of each notice. Use this ID to locate the translations of these danger and caution
notices in the Brocade Product Safety Notices.

Danger notices

A danger notice calls attention to a situation that is potentially lethal or extremely hazardous to people. A
lightning bolt symbol accompanies a danger notice to represent a dangerous electrical condition. Read and
comply with the following danger notice before installing or servicing this device.

Use the supplied power cords. Ensure the facility power receptacle is the correct type, supplies the
required voltage, and is properly grounded. (D004)

Brocade VDX 8770-8 QuickStart Guide 5 of 34
Publication Number: 53-1002555-01

Caution notices

CAUTION

NOTE

A caution notice calls attention to a situation that is potentially hazardous to people because of some existing
condition. Read and comply with the following caution notice before installing or servicing this device.

Use safe lifting practices when moving the product. (C015)

ESD precautions

The Brocade VDX 8770-8 contains ESD-sensitive FRUs. When working with any Brocade VDX 8770-8 FRU, use
correct electrostatic discharge (ESD) procedures.

• Wear a wrist grounding strap connected to chassis ground (if the Brocade VDX 8770-8 is plugged in) or a

bench ground. Refer to Figure 1 on page 7 for the location of the ESD jack.

• Store ESD-sensitive components in antistatic packaging.

Brocade VDX 8770-8, port side

Airflow in the Brocade VDX 8770-8 is from the port side and left side (viewed from the port side) to the rear (fan side)
of the chassis.

Figure 1 displays a sample configuration of the port side of the Brocade VDX 8770-8.

6 of 34 Brocade VDX 8770-8 QuickStart Guide

Publication Number: 53-1002555-01

1 Line cards L1 through L4 (left to right) 6 Intake Vent

2 Cable management comb 7 Management modules MM1 and MM2 (left to

right)

3 Switch fabric modules S1 through S6 (odd numbers

above, even numbers below, left to right)

4 Line cards L5 through L8 (left to right) 9 ESD jack

5 Mounting flanges

8 Power supplies 1 through 8 (1 through 4 above,

left to right, 5 through 8 below, left to right))

FIGURE 1 Port side of the Brocade VDX 8770-8 (sample configuration)

Brocade VDX 8770-8 QuickStart Guide 7 of 34
Publication Number: 53-1002555-01

Brocade VDX 8770-8, nonport side

Figure 2 displays a sample configuration of the nonport side view of the Brocade VDX 8770-8.

1 Fan assemblies 1 and 2 (left to right) 3 Power supply exhaust vent
2 Fan assemblies 3 and 4 (left to right) 4 Ground lug

FIGURE 2 Nonport side of the Brocade VDX 8770-8 (sample configuration)

8 of 34 Brocade VDX 8770-8 QuickStart Guide

Publication Number: 53-1002555-01

Items included with the Brocade VDX 8770-8

NOTE

The Brocade VDX 8770-8 ships with the following items:

• Brocade VDX 8770-8 chassis, populated with: (management modules, switch fabric modules, and line cards are

all packaged separately)

- Management modules (one)

- Switch fabric modules (up to six)

- Line cards (up to eight)

- Filler panels for unoccupied slots for all modules

- Power supplies (up to eight)

- Power supply filler panels for unoccupied bays

- Fan assemblies (four)

• Accessory kit containing the following items:

- Console cable (RS-232 serial cable: The RS-232 cable has an adapter at one end that can be removed to

provide an RJ-45-style connector.)

- Wrist strap (ESD grounding strap)

- Ground lug kit

- SFP extraction tool kit

- China RoHS guide

- Cable management comb

- Brocade-branded USB device

- Power cord retainer kit

- Brocade VDX 8770-8 QuickStart Guide (this publication)

- Hardware for securing the switch in a rack

- Web pointer document

- Air filter

The rack mount kits must be ordered separately.

Order the Brocade-branded transceivers (SFP, SFP+, or QSFP) and cables or direct-attach cables from your Brocade
distributor. The Brocade VDX 8770-8 supports SR and LR SFP and SFP+ transceivers. The QSFP transceivers are SR
transceivers only.

For information about the transceivers that are qualified for the Brocade VDX 8770-8, refer to

http://www.brocade.com/downloads/documents/matrices/Brocade_Compatibility_Matrix.pdf.

Brocade VDX 8770-8 QuickStart Guide 9 of 34
Publication Number: 53-1002555-01

Preparing for the Brocade VDX 8770-8 installation

NOTE

NOTE

CAUTION

DANGER

Refer to the safety notices before installation (“Safety notices”).
Refer to “Power specifications” to plan for meeting power supply standards before installing the chassis.
Refer to “Environmental requirements” to plan for your environmental needs.
Refer to “Managing cables” to plan for cable management.

The following steps are required to ensure correct installation and operation.

1. Provide a space that is 15 rack units (15U) high, 61.29 cm (24.09 in.) deep, and 43.74 cm (17.22 in.) wide. One
rack unit is equal to 4.45 cm (1.75 in.).

Plan to install the Brocade VDX 8770-8 with the port side facing the air-intake aisle. Airflow is from the port side
of the switch to the fan side.

Ensure that the rack is balanced and mechanically secured to provide stability in the event of an earthquake
and that the equipment does not exceed the rack’s weight limits.

Doorways must be wider than 91 cm (36 in.) to accommodate the switch.

2. Ensure that dedicated electrical branch circuits with the following characteristics are available:

• Up to eight dedicated fused 200–240 VAC, 50–60 Hz feeds or -48 VDC (one per power supply)

• One cable for each power supply

Use a separate branch circuit for each AC power cord for redundancy in case one of the circuits fails.

• Protected by a circuit breaker in accordance with local electrical codes

• Supply circuit, line fusing, and wire size adequate to the electrical rating on the switch nameplate

• Location close to the switch and easily accessible

• Grounded outlets installed by a licensed electrician and compatible with the power cords

If the installation requires a different power cord than the one supplied with the switch, make sure you
use a power cord displaying the mark of the safety agency that defines the regulations for power cords in
your country. The mark is your assurance that the power cord can be used safely with the switch.

3. Plan for cable management before installing the switch.

Cables can be managed in a variety of ways, such as by routing cables below the switch, to either side of the
switch, through cable channels on the sides of the rack, or by using patch panels.

4. Ensure that the following items are available for configuration of the Brocade VDX 8770-8:

• Workstation with an installed terminal emulator, such as HyperTerminal

• Console (serial) cable (provided)

• Ethernet cables (not provided)

10 of 34 Brocade VDX 8770-8 QuickStart Guide

Publication Number: 53-1002555-01

• Either access to an FTP server or a Brocade USB device for backing up the switch configuration or collecting

CAUTION

supportsave output data (optional)

• Transceivers (copper and optical) and compatible cables and direct-attach cables if needed

5. Ensure that the air intake and exhaust vents have a minimum of 5.1 cm (2 in.) of airspace.

6. Ensure that the air temperature on the air intake side is less than 40°C (104°F) during operation.

Power specifications

Power for the Brocade VDX 8770-8 can be supplied with either AC- or DC-based 3000 watt power supplies. The
Brocade VDX 8770-8 has room for up to eight power supplies.

Tab le 2 shows the basic power specifications for each power supply.

.

TABLE 2 Power specifications

Specification Value for 3000W AC power supply Value for 3000W DC power supply

Input rating 16A 70A

Input voltage 200–240 VAC, 50-60 Hz, 16.0 Amp

maximum

Operating range 180 ot 264 VAC -40 to -60 VDC

Inrush current Limited to 60 Amp peak for any initial

current surge or spike of 10 ms or less at
either cold or warm start. Any additional
inrush current surges or spikes in the form
of AC cycles or multiple AC cycles greater
than 10 ms and less than 150 ms, must not
exceed 25 Amp peak.

Output 12 VDC, 245 Amps 12 VDC, 245 Amps

-48 VDC

Limited to 70 Amp peak for any initial
current surge or spike of 10 ms or less at
either cold or warm start.

For the DC input circuit to the system of a Brocade VDX 8770-8 (3000W power supply), make sure there
is an 80 Amp circuit breaker, minimum -48 VDC, double pole, on the input lugs to the power supply. The
input wiring for the connection to the switch should be copper wire, 2 American Wire Guage (AWG),
marked VW-1, and rated minimum 90°C.

The power requirements for a given switch configuration depend on which modules have been installed in the
switch. Tabl e 3 shows the power consumption for the modules that can be used in the Brocade VDX 8770-8 switch
along with the power consumption for the cooling fans.

All numbers for the line cards assume that the card is fully populated with optical transceivers, including QSFPs for
the 12x40 GbE line cards. All ports are Ethernet.

Brocade VDX 8770-8 QuickStart Guide 11 of 34
Publication Number: 53-1002555-01