Broan NuTone Eclipse 2830, NuTone Eclipse 2836 Specification Sheet

MODELS 2830 & 2836

ECLIPSE

REMOTE DOWNDRAFT

SPECiFiCATiON SHEET

Control a powerful exterior blower from the
cooktop location.

FEATURES
HOUSING:

• Rugged steel construction

• Finished with black, electrically-bonded epoxy paint

• Space-saving - can be used with most cooktops on the
market

• 30" or 36" size - Fits standard-size cabinets

AIR VENT ASSEMBLY:

® Brushed stainless steel cover - just press button

to turn unit "ON"

• Designer White or Black doors - available

separately

• Air vent rises to 7" from cooktop for optimum
removal of cooking contaminants

• Two washable aluminum grease filters

• Stainless steel face plate - makes cleanup quick

and easy

• Flush-mounted, infinite speed blower control

• Conveniently located button - press to lower air

vent and turn unit "OFF"

TYPICAL SPECiFiCATiON

Downdraft blower system shall be Broan Model 2830
(Broan Model 2836).

Unit to have steel housing with electrically-bonded paint
finish. Air vent to rise at least 7" and have a stainless steel

face plate for ease of cleaning.
Filters to be washable and removable from above.

31_'' x 10" duct connector shall be adjustable to
accomodate different duct positions.

Downdraft system shall operate on 120 VAC and be able
to be plugged into a standard grounded outlet. It will have

an infinite speed blower control.

SPECIFICATIONS

VOLTS Hz AMPS

120 60 6 Amps

DISCHARGE

31_" x 10"

Broan-NuTone LLC, 926 West State Street, Hartford, WI 53027 (1-800-637-1453)

NuTone, Inc., 4820 Red Bank Road, Cincinnati, OH 45227 (1-800-543-8687)

REFERENCE

QTY. REMARKS Project

Location

Architect

Engineer
Contractor

Submitted by

Date

20G 99041821E

iNSTALLATiON PLANNING - MODELS 2830 & 2836

DiMENSiONS

NOTE: Dimensions shown are for reference only. Before cutting
out countertop, refer to instructions packed with downdraft and
cooktop.

DOWNDRAFT

A

COOKTOP

DOWNDRAFT

-- FRONT TO BACK --
INSIDE CABINET DEPTH I

I

Refer to the cooktop installation instructions for dimensions of
cooktop, countertop cut-out, and cabinet requirements. The 2830

and 2836 can be installed in most standard 30" and 36" wide
cabinets.

Cooktop depth can vary greatly from one to another. This may
cause the fit of these two appliances to be rather tight.

Pay special attention to the 4 areas of potential interference
highlighted above. The back of the downdraft cut-out will be 1-3/
4" from the cooktop and 2" of FLAT countertop is needed behind
cooktop.

DUCTWORK

TYPICAL iNSTALLATiON

COUNTER

TOP COOKTOP

VENT

3-1/4"x10"
DUCTCONNECTOR

CHIMNEYTOP

/

7 7/8

1

3 5/8

4.

120VAC
GROUNDED

OUTLET

The downdraft has 31A"x 10" discharge. Transitions are available
to connect it to the 10" round inlet on the Broan Models 331 or 332

exterior blowers. See below.

3¼"X10"

DUCT CONNECTOR

3-1/4" x 10"

TRANSITION __

TO 8"

3-1/4" X 10"

8" x 10" TO

INCREASER

8" RD,

ELBa6 FT,

ELECTRICAL

The unit has a 2 ft. power cord with a 3-pronged plug. Plan to
provide a grounded outlet within reach of this cord. Outlet may

also be wall-mounted, with access hole in cabinet. If local codes
call for hard-wiring, see installation instructions.

The system will operate most efficiently when the ductwork does
not exceed 40 feet of equivalent duct. The illustrations above,
show equivalent feet of elbows and transitions. The number of feet
of straight 3-1/4" x 10" or 6" duct plus the equivalent feet of elbows
or transitions to be used should equal 40 feet or less.