Broan B5936SS Specifications
B5936SS
RANGE HOOD
SPECIFICATION SHEET
Gently curving metal canopy creates
a dramatic, contemporary appearance
and an open, airy feel.
FEATURES
Ceiling mount
•
Finish: 430 Stainless Steel #4 Brushed
•
Width: 34-7/8”
•
Telescopic flue accommodates 8’ to 9’
•
ceilings
6” round duct connector/backdraft damper
•
Convertible to non-ducted operation -
•
requires Model RK59 (sold separately)
Halogen lighting (4 x 20 watt, 12V, Type
•
JC 12V 20W G4 Base) (bulbs included)
5 push-button control: blower on-off, blower
•
low speed, blower medium speed, blower
high speed, light on-off
Single centrifugal blower
•
Dishwasher-safe grease filters feature a
•
quick-release latch
SPECIFICATIONS
VOLTS AMPS CFM SONES DUCT
120 3.3
190 (low) 2.5 (low)
450 (high) 8.5 (high)
HVI-2100 CERTIFIED RATINGS comply with new testing
technologies and procedures prescribed by the Home
Ventilating Institute, for off-the-shelf products, as they are
available to consumers. Product performance is rated
at 0.1 in. static pressure, based on tests conducted in
a state-of-the-art test laboratory. Sones are a measure
of humanly-perceived loudness, based on laboratory
measurements.
10-9/16”
11-1/8”
6” round
OPTIONS
Replacement grease filters available
•
Flue extension for 10’ ceiling (Model
•
FXN59SS) (35-5/8” long) (ducted or nonducted)
Non-duct kit (Model RK59)
•
(Non-duct option available only in the U.S.)
Replacement non-ducted recirculating filter
•
available (Model FILTER 59)
Broan-NuTone LLC Hartford, Wisconsin www.broan.com 800-558-1711
REFERENCE QTY. REMARKS Project
Location
Architect
Engineer
Contractor
Submitted by Date
27-3/4” - 42“ Ducted
29-1/2” - 42” Non-Ducted
34-7/8”
90K 99044486D
23-9/16”
CEILING SUPPORT INSTALLATION
CEILING
JOISTS
CROSS
FRAMING
CEILING
MOUNTING
PLATE
(8) M6 x 40mm
WOOD
SCREWS
6” ROUND DUCTWORK
8
⅞
FR ON T
HOUSE
WIRING
ELECTRICAL
OUTLET
BOX
1. At hood location install 2 x 4 cross framing between ceiling
joists using dimensions shown. Make sure framing does not
interfere with electrical outlet box opening in ceiling mount-
”
ing plate.
2. Install house wiring and ductwork.
3. Finish ceiling surface. Be sure to mark the location of the
ceiling joists & cross framing. Bring house wiring through
finished ceiling.
4. Remove cover from electrical outlet box on ceiling mounting plate. Pull house wiring through hole on top of mounting
plate and into electrical outlet box. Secure house wiring
cable to mounting plate / electrical box with appropriate connector.
5. Install ceiling mounting plate with the side marked “front”
at the desired hood location. Secure using (8) M6 x 40mm
wood screws. Make sure screws are driven into the center of
the framing for maximum strength.
NOTE:
Minimum hood distance above cooktop must not be less than
30”.
A maximum of 36” above the cooktop is highly recommended
for best capture of cooking impurities.
Distances over 36” above the cooktop are at the installer’s
and user’s discretion - providing that ceiling height and flue
length permit.
On 8-ft. ceilings
Hood distance above cooktop is:
Minimum 30”, Maximum 32-1/4” (for ducted discharge)
Minimum 30”, Maximum 30-1/2” (for non-ducted discharge)
On 9-ft. ceilings
Hood distance above cooktop is:
Minimum 30”, Maximum 36” (for both ducted and non-ducted
discharge)
On 10-ft. ceilings
Hood distance above cooktop is:
Minimum 30”, Maximum 36” (for both ducted and non-ducted
discharge).
10-ft. ceilings require 10-ft. Flue Extension, Model FXN59SS
for ducted or non-ducted installations (purchase separately).
Broan-NuTone LLC Hartford, Wisconsin www.broan.com 800-558-1711
Loading...