Broan B5830SS Installation Manual
CHIMNEY
!
!
!
!
RANGE HOOD
READ AND SAVE THESE INSTRUCTIONS
Intended for domestIc cookIng only.
MODELS B5830SS • B5836SS
Page 1
To register this product visit:
www.broan.com
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO PERSON(S) OBSERVE THE
FOLLOWING:
1. Use this unit only in the manner intended by the manufacturer.
If you have questions, contact the manufacturer at the
address or telephone number listed in the warranty.
2. Before servicing or cleaning unit, switch power off at service
panel and lock service disconnecting means to prevent
power from being switch on accidentally. When the service
disconnecting means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the service
panel.
3. Installation work and electrical wiring must be done by
qualified personnel in accordance with all applicable codes
and standards, including fire-rated construction codes and
standards.
4. Sufficient air is needed for proper combustion and exhausting
of gases through the flue (chimney) of fuel burning equipment
to prevent backdrafting. Follow the heating equipment
manufacturer’s guidelines and safety standards such as
those published by the National Fire Protection Association
(NFPA), the American Society for Heating, Refrigeration
and Air Conditioning Engineers (ASHRAE) and the local
code authorities.
5. When cutting or drilling into wall or ceiling, do not damage
electrical wiring and other hidden utilities.
6. Ducted fans must always be vented to the outdoors.
7. Do not use this unit with any other solid-state speed control
device.
8. To reduce the risk of fire, use only steel ductwork.
9. This unit must be grounded.
TO REDUCE THE RISK OF A RANGE TOP GREASE
FIRE:
a) Never leave surface units unattended at high settings.
Boilovers cause smoking and greasy spillovers that may
ignite. Heat oils slowly on low or medium settings.
b) Always turn hood ON when cooking at high heat or when
cooking flaming foods (i.e. Crêpes Suzette, Cherries Jubilee,
Peppercorn Beef Flambé).
c) Clean ventilating fans frequently. Grease should not be
allowed to accumulate on fan or filters.
d) Use proper pan size. Always use cookware appropriate for
the size of the surface element.
WARNING
TO REDUCE THE RISK OF INJURY TO PERSON(S)
IN THE EVENT OF A RANGE TOP GREASE FIRE,
OBSERVE THE FOLLOWING*:
1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or
metal tray, then turn off the burner. BE CAREFUL TO PREVENT
BURNS. IF THE FLAMES DO NOT GO OUT IMMEDIATELY,
EVACUATE AND CALL THE FIRE DEPARTMENT.
2. NEVER PICK UP A FLAMING PAN – You may be burned.
3. DO NOT USE WATER, including wet dishcloths or towels –
This could cause a violent steam explosion.
4. Use an extinguisher ONLY if:
A. You know you have a Class ABC extinguisher and you
know how to operate it.
B. The fire is small and contained in the area where it
started.
C. The fire department has been called.
D. You can fight the fire with your back to an exit.
* Based on “Kitchen Fire Safety Tips” published by NFPA.
CAUTION
1. For indoor use only.
2. For general ventilating use only. Do not use to exhaust
hazardous or explosive materials and vapors.
3. To avoid motor bearing damage and noisy and/or
unbalanced impeller, keep drywall spray, construction dust,
etc. off power unit.
4. Do not use over cooking equipment greater than 60,000
BTU/hr. as the blower motor will shut down intermittantly.
5. Your hood motor has a thermal overload which will
automatically shut off the motor if it becomes overheated.
The motor will restart when it will cool down. If the motor
continues to shut off and restart, have the hood serviced.
6. The bottom of the hood MUST NOT BE LESS than 30” and
at a maximum of 36” above cooktop for best capture of
cooking impurities.
7. Two installers are recommended because of the size of
this hood.
8. To reduce risk of fire and to properly exhaust air, be sure
to duct air outside. Do not exhaust air into spaces within
walls or ceilings or into attics, crawl spaces, or garages.
9. Be careful when installing the decorative flue and hood,
they may have sharp edges.
10. Please read specification label on product for further
information and requirements.
INSTALLER: LEAVE THIS GUIDE TO THE HOMEOWNER.
HOMEOWNER: OPERATION AND MAINTENANCE INFORMATION ON PAGE 8.
MODELS B5830SS • B5836SS
INSTALL THE DUCTWORK
(Ducted Hoods Only)
1. Decide where
the ductwork
will run
between the
hood and the
outside.
2. A straight, short
duct run will
allow the hood
to perform most
efficiently.
3. Long duct
runs, elbows
and transitions
will reduce the
ABOVE COOKING SURFACE
performance of
the hood. Use as few of them as possible. Larger ducting
may be required for best performance with longer duct runs.
4. Install wall cap or roof cap. Connect round metal ductwork
to cap and work back towards the hood location. Use duct
tape to seal the joints between ductwork sections.
ROOF CAP
DECORATIVE
FLUE
HOOD
30" TO 36"
6"
ROUND DUCT
ROUND
ELBOW
WALL CAP
Page 2
PREPARE THE HOOD
Unpack hood and check contents. You should receive:
1 - Hood
1 - Decorative Flue Assembly
1 - Damper / Duct Connector
1 - Lower Flue Mounting Bracket
1 - Upper Flue Mounting Bracket
1 - Hood Mounting Bracket
2 - Aluminum Grease Filters (installed in hood)
1 - Parts Bag containing:
10 - Mounting Screws (#8 x 3/8” Pan Head)
7 - Mounting Screws (#8 x 1-1/2” Flat Head)
7 - Drywall Anchors
2 - Washers
1 - Installation Manual
10 MOUNTING
SCREWS (#8 x
3/8” Pan Head)
MEASURE THE INSTALLATION
ROOF CAP
6” ROUND DUCT
DECORATIVE FLUE
ROUND ELBOW
HOOD
11 3/4”
30” TO 36” ABOVE
COOKING SURF ACE
WALL CAP
HOOD
MOUNTING
BRACKET
12 5/8”
TO CENTER OF
BRACKET HOLES
DECORATIVE FLUE
DAMPER / DUCT
CONNECTOR
7 MOUNTING
SCREWS
(#8 X 1-1/2”
Flat Head)
UPPER
FLUE MOUNTING
BRACKET
LOWER
FLUE MOUNTING
BRACKET
2 WASHERS
7 DRYWALL
ANCHORS
HOOD
MOUNTING
BRACKET
The minimum hood distance above cooktop MUST NOT BE
LESS than 30”.
A maximum of 36” above cooktop is highly recommended for
best capture of cooking impurities.
Distances over 36” are at the installer and users discretion;
providing that the ceiling height permits.
MODELS B5830SS • B5836SS
Page 3
INSTALL THE WIRING
14”
MAX.
1. GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock
by providing an escape wire for the electric current. This
appliance is equipped with a cord having a grounding wire
with a grounding plug. The plug must be plugged into an
outlet that is properly installed and grounded.
NOTE:
A recessed “clock” outlet is recommended.
2. Position the electrical outlet within the space covered by the
decorative flue and where it will not interfere with the round
duct. Make sure the outlet is no further than 14” from where
the cord exits from the hood and that the outlet does not
interfere with a mounting bracket fastening area or where the
decorative flue touches the wall.
INSTALL THE HOOD MOUNTING
BRACKET
WALL STUDS
FRAMING BEHIND
DRYWALL
C
L
77⁄8”
315⁄16”
425⁄8” to 485⁄8” above cooktop
425⁄8” = bottom of hood 30” above cooktop
485⁄8” = bottom of hood 36” above cooktop
1. Construct wood wall framing that is flush with interior surface
of wall studs.
Make sure:
a) the framing is centered over installation location.
b) the height of the framing will allow the mounting bracket
to be secured to the framing within the dimensions
shown.
2. After wall surface is finished, carefully center and level the
hood mounting bracket and secure it to wall framing with (3)
#8 x 1-1/2” mounting screws. Tighten the screws completely.
NOTE:
On 8-ft. ceilings
Hood distance above cooktop is:
Minimum 30”, Maximum 32-3/4” (for ducted discharge)
Minimum 30”, Maximum 30” (for non-ducted discharge)
On 9-ft. ceilings
Hood distance above cooktop is:
Minimum 30”, Maximum 36” (for both ducted and non-ducted
discharge)
On 10-ft. ceilings
Hood distance above cooktop is:
Minimum 30”, Maximum 36” (for both ducted and non-ducted
discharge).
NOTE: 10-ft. ceilings require 10-ft. Flue Extension, Model
FXN58SS for ducted or non-ducted installations (purchase
separately).
19⁄16”
MODELS B5830SS • B5836SS
Page 4
INSTALL UPPER FLUE MOUNTING
BRACKET
Ceiling
11⁄8”
Ø 5/16” TYP.
Flush with
the ceiling
Recommended
distance between
screw holes
Ceiling
Center of installation
C
L
4¼”
21⁄8”
Center of
installation
C
L
Upper flue mounting
bracket slots
INSTALL THE HOOD
(Horizontally Ducted Hoods Only)
1. DO NOT REMOVE the protective plastic film covering the
decorative flue and the hood at this time.
2. Lay the back side of the hood flat on a table. Use a piece of
cardboard to avoid damaging the table or the hood.
3. Attach damper / duct connector to top of hood using (4) #8
x 3/8” Pan Head mounting screws.
4. Remove the grease filters by pulling down the metal latch
tab and tilting filters downward to remove.
5. Carefully rotate hood upright.
LOWER FLUE
MOUNTING BRACKET
14¼”
MAX.
1. Drill two 5⁄16” diameter holes where shown. Insert drywall
anchors into the holes.
2. Center the bracket over the hood location and flush with the
ceiling. Make sure that the slots of the upper flue bracket are
at the bottom. Secure the upper flue bracket to the wall using
(2) #8 x 1½” mounting screws.
3. Tighten the screws completely. Make sure that the bracket
is tight against the wall.
6. To make sure there will be adequate clearance between top
of hood and lower flue mounting bracket for ductwork: Elbow
must be located below lower flue mounting bracket.
7. Align the hood and center it above the hood mounting
bracket. Gently lower the hood until it securely engages the
bracket.
INSIDE BACK OF HOOD
MOTOR/BLOWER
ASSEMBLY
SIDE VIEW
HOLES
LOCATION
8. With the hood hanging in place, drill through both holes
located in the inside lower back of hood using a 5⁄16” drill
bit. Insert the included drywall anchors into the drilled holes
(one for each hole). Install (2) washers and (2) #8 x 1-1/2”
mounting screws through the hood back and into the drywall
anchors. Verify that the hood is centered and leveled. Tighten
all screws completely.
9. Reinstall grease filters by aligning rear filter tabs with slots
in the hood. Pull down the metal latch tab, push filter into
position and release. Make sure filters are securely engaged
after installation.
Ø 5/16” TYP.
MODELS B5830SS • B5836SS
Page 5
6” ROUND
DUCT ELBOW
10. Measure and install 6” round steel ductwork to roof cap or
wall cap and 90o elbow over duct collar on hood. Use duct
tape to make all joints secure and air tight.
11. Plug hood power cord into the outlet.
LOWER FLUE MOUNTING BRACKET
UPPER FLUE MOUNTING BRACKET
UPPER
FLUE
14. Slide the upper flue upward until it is aligned with its upper
mounting bracket. The bracket should be inside the flue.
Secure the upper flue to the upper flue mounting bracket
using (2) #8 x 3/8” mounting screws.
15. Remove protective plastic film covering the upper flue and
the hood.
INSTALL THE HOOD
(Vertically Ducted Hoods Only)
LOWER
FLUE
NOTE: 10-ft. ceilings require 10-ft. Flue Extension Model
FXN58SS (purchase separately). Discard the upper flue
supplied with your hood and replace it with the Model
FXN58SS flue extension.
12. Remove the upper flue from inside the lower flue. Install the
lower flue bracket to the lower flue using (2) flue bracket
screws #8 x 3/8”, make sure that the slots are at the top.
Carefully replace the upper flue inside the lower flue.
Remove protective plastic film covering the lower flue only.
13. Carefully place both flues into the recessed area of hood
top. Slightly push aside the upper flue to avoid any damage
while installing the lower flue to the hood top using (2) #8 x
3/8” screws through the lower flue side slots.
1. DO NOT REMOVE the protective plastic film covering the
decorative flue and the hood at this time.
2. Lay the back side of the hood flat on a table. Use a piece of
cardboard to avoid damaging the table or the hood.
3. Attach damper / duct connector to top of hood using (4) #8
x 3/8” Pan Head mounting screws.
4. Remove the grease filters by pulling down the metal latch
tab and tilting filters downward to remove.
5. Carefully rotate hood upright.
LOWER FLUE MOUNTING BRACKET
LOWER
FLUE
NOTE: 10-ft. ceilings require 10-ft. Flue Extension Model
FXN58SS (purchase separately). Discard the upper flue
supplied with your hood and replace it with the Model
FXN58SS flue extension.
6. Remove the upper flue from inside the lower flue. Install the
lower flue bracket to the lower flue using (2) flue bracket
screws #8 x 3/8”, make sure that the slots are at the top.
Carefully replace the upper flue inside the lower flue.
Remove protective plastic film covering the lower flue only.
7. Carefully place both flues into the recessed area of hood
top.
MODELS B5830SS • B5836SS
Page 6
6” ROUND
STEEL DUCT
DUCT LENGTH
DECORATIVE
FLUE
8. Measure and install steel ductwork to hood duct connector.
Use duct tape to make all joints secure and air tight.
9. Hold hood up close to wall mounting location and plug
power cord into wall outlet.
10. Align the hood and center it above the hood mounting
bracket. Make sure ductwork on hood lines up and attaches
to ductwork in ceiling. Gently lower the hood until it securely
engages the bracket.
11. Use duct tape to make all joints secure and air tight.
INSIDE BACK OF HOOD
MOTOR/BLOWER
ASSEMBLY
UPPER FLUE MOUNTING BRACKET
UPPER
FLUE
15. Slide the upper flue upward until it is aligned with its mounting
bracket. The bracket should be inside the flue. Secure the
upper flue to the upper flue mounting bracket using (2) #8 x
3/8” mounting screws.
16. Remove protective plastic film covering the upper flue and
the hood.
INSTALL THE HOOD
(Non-Ducted Hoods Only)
NON-DUCT KIT MODEL RK58 CONTENTS
SIDE VIEW
HOLES
LOCATION
12. With the hood hanging in place, drill through both holes
located in the inside lower back of hood using a 5⁄16” drill
bit. Insert the included drywall anchors into the drilled holes
(one for each hole). Install (2) washers and (2) #8 x 1-1/2”
mounting screws through the hood back and into the drywall
anchors. Verify that the hood is centered and leveled. Tighten
all screws completely.
13. Reinstall grease filters by aligning rear filter tabs with slots
in the hood. Pull down the metal latch tab, push filter into
position and release. Make sure filters are securely engaged
after installation.
14. Slightly push aside the upper flue to avoid any damage while
installing the lower flue to the hood top using (2) #8 x 3/8”
screws through the lower flue side slots.
Ø 5/16” TYP.
NON-DUCTED
RECIRCULATION
NON-DUCT
PLENUM
NON-DUCT PLENUM
COLLAR
NOTE: Non-ducted installations require Non-Duct Kit,
Model RK58 (purchase separately).
1. CAUTION: Do not use plastic or rigid metal duct.
2. Do not remove the protective plastic film covering the
decorative flue and the hood at this time.
3. Lay the back side of the hood flat on a table. Use a piece of
cardboard to avoid damaging the table or the hood.
4. Attach damper / duct connector to top of hood using (4) #8
x 3/8” Pan Head mounting screws.
5. Remove damper flaps from damper / duct connector and
discard flaps.
8 MOUNTING
SCREWS
(ST4 x 8
Round Head)
WRAPS
FILTERS
2 TIE
FLEXIBLE DUCT
6. Remove the
grease filters
by pulling
down the
metal latch
tab and
tilting filters
downward to
remove.
7. Attach non-duct collar to non-duct plenum using (4) ST4 x
8 round head screws.
8. Measure distance “A”. This will be the length of the
extended flex duct.
MODELS B5830SS • B5836SS
Page 7
14. Hold hood up close to wall mounting location and plug
power cord into wall outlet.
15. Align the hood and center it above the hood mounting bracket.
Gently lower the hood until it securely engages the bracket.
INSIDE BACK OF HOOD
MOTOR/BLOWER
ASSEMBLY
SIDE VIEW
9. Attach
aluminum
NON-DUCT PLENUM
3-5/8”
flexible
duct to the
damper / duct
connector
6” ALUMINUM
FLEX DUCT
A
with a tie
wrap.
10. Attach flexible
DAMPER / DUCT
CONNECTOR
duct to nonduct plenum
collar and
secure with
tie wrap. Tape
all joints with
duct tape.
NOTE: 10-ft. ceilings require 10-ft. Flue Extension Model
FXN58SS (purchase separately). Discard the upper flue
supplied with your hood and replace it with the Model
FXN58SS flue extension.
LOWER FLUE MOUNTING BRACKET
HOLES
Ø 5/16” TYP.
LOCATION
16. With the hood hanging in place, drill through both holes
located in the inside lower back of hood using a 5⁄16” drill
bit. Insert the included drywall anchors into the drilled holes
(one for each hole). Install (2) washers and (2) #8 x 1-1/2”
mounting screws through the back of the hood and into
the drywall anchors. Verify that the hood is centered and
leveled. Tighten all screws completely.
17. Attach (2)
two non-duct
recirculation
filters to sides
of blower by
aligning key lock
slot and rotating
until filters lock
into place.
For replacement non-duct recirculation filters - purchase
S97018030 or ROUNDFILTER.
18. Reinstall grease filters by aligning rear filter tabs with
slots in the hood. Pull down the metal latch tab, push filter
into position and release. Make sure filters are securely
engaged after installation.
LOWER
FLUE
11. Remove the upper flue from inside the lower flue. Install the
lower flue bracket to the lower flue using (2) flue bracket
screws #8 x 3/8”, make sure that the slots are at the top.
Carefully replace the upper flue inside the lower flue.
Remove protective plastic film covering the lower flue only.
12. Carefully place both flues into the recessed area of hood
top. Slightly push aside the upper flue to avoid any damage
while installing the lower flue to the hood top by using (2) #8
x 3/8” screws through the lower flue side slots.
13. Attach non-duct plenum with collar to upper flue using (4)
ST4 x 8 round head screws.
UPPER FLUE MOUNTING BRACKET
UPPER
FLUE
19. Sli de up the upp er flue upward until i t is aligned wi th its mounti ng
bracket. The bracket should be inside the flue. Secure the
upper flue to the upper flue mounting bracket using (2) #8 x
3/8” mounting screws.
20. Remove protective plastic film covering the flue and the hood.
MODELS B5830SS • B5836SS
!
!
!
Page 8
LIGHT BULBS
LIGHT BULB COVER
WARNING
Bulbs may be hot. Always allow bulbs to cool down before
removing them.
This range hood requires two halogen bulbs (Type JC, 12V, 20W
Max, G-4 Base).
To change bulbs:
1. Remove light bulb cover by gently pushing it upward and
turning it counterclockwise.
2. Replace bulb.
3. Re-install light bulb cover by gently pushing it upward and
turning it clockwise.
OPERATION
OFF
LOW
FAN CONTROLS
MED.
HIGH
LIGHT
ON/OFF
MAINTENANCE
Grease Filters
Grease filters should be cleaned monthly. Remove grease
filters by pulling down on the metal latch tab. This will
disengage the filter from the hood. Tilt the filter downward and
remove.
To clean all-metal filters: Use a warm detergent solution or
put them in the dishwasher using a non-phosphate detergent.
Discoloration of the filter may occur if using phosphate
detergent or as a result of local water conditions - but this will
not affect filter performance. This discoloration is not covered
by the warranty.
Non-Duct Recirculation Filters
Change the non-duct recirculation filters every 6 months.
Rotate the filters to remove them from the blower and replace.
Hood Cleaning
How to maintain the bright look of stainless steel and help
prevent corrosion.
Dos:
- Once a month, wash surfaces with clean cloth or rag soaked
with warm water and mild soap or liquid dish detergent.
- Always clean in the direction of original polish lines.
- Always rinse well with clear water (2 or 3 times) after
cleaning. Wipe dry completely.
- You may also use a specialized household stainless steel
cleaner.
Don’ts:
- Do not use any steel or stainless steel wool or any other
scrapers to remove stubborn dirt.
- Do not use any harsh or abrasive cleansers.
- Do not allow dirt to accumulate.
- Do not let plaster dust or any other construction residues
reach the hood. During construction or renovation, cover the
hood to make sure no dust sticks to stainless steel surface.
Avoid: when choosing a detergent
- Any cleaners that contain bleach will attack stainless steel.
- Any products containing : chloride, fluoride, iodide,
bromide will deteriorate surfaces rapidly.
- Any combustible products used for cleaning such as
acetone, alcohol, ether, benzol, etc., are highly explosive
and should never be used close to a range.
The hood is operated using the push buttons on the front panel.
Push the light button to turn the lights on and off.
Push the fan controls to select low, medium, or high blower
speed.
Push the OFF button to turn the blower off.
MODELS B5830SS • B5836SS
stop low mid
high lamp
GRN / YLW
SERVICE PARTS
KEY PART NO. DESCRIPTION QTY.
1 S99526972 Decorative Upper and Lower Flues 1
2 S99526974 Motor / Blower Assembly 1
3 S99526975 Light Socket Assembly 2
4 S99527010 Light Trim Ring / Lens Assembly 2
5 S99526976 Push Button Assembly 1
6 S97018027 Aluminum Grease Filters (2 per hood) B5830SS 1
S97018028 Aluminum Grease Filters (3 per hood) B5836SS 1
7 S97018030 Non-Duct Recirculation Filters (pair) 1
8 S99526983 Damper / Duct Connector 1
9 S99526984 6” Dia. Expandable Flexible Aluminum Duct 1
10 S99526992 Non-Duct Plenum Assembly 1
11 S99526986 Hood Mounting Bracket 1
12 S99526988 Lower Flue Mounting Bracket 1
13 S99526990 Upper Flue Mounting Bracket 1
S99527011 Transformer (not shown) 1
S99527012 Capacitor (not shown) 1
S99527013 Plastic Cover (not shown) 1
S99526993 Parts Bag (not shown) 1
Order service parts by Part No. - not by Key No.
WIRING DIAGRAM
Page 9
13
10
12
1
9
11
8
3
4
TO MOTOR
HALOGEN LIGHTS
TRANSFORMER PCB
CAPACITOR
BLK
Y
WOR
B
B
R
L
N
GRN
K
PUSHBUTTON
7
2
5
R
BLK
W
R
O
B
R
N
WG
BRN
BLK
W
B
B
W
L
R
L
K
Y
K
BLU
6
Replacement parts can be ordered on our website:
WARRANTY
Broan-NuTone warrants to the original consumer purchaser of its products that such products will be free from defects in materials or workmanship for a period of one year from the date of
original purchase. THERE ARE NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE.
During this one-year period, Broan-NuTone will, at its option, repair or replace, without charge, any product or part which is found to be defective under normal use and service.
THIS WARRANTY DOES NOT EXTEND TO FLUORESCENT LAMP STARTERS, TUBES, HALOGEN AND INCANDESCENT BULBS, FUSES, FILTERS, DUCTS, ROOF CAPS, WALL CAPS AND OTHER
ACCESSORIES FOR DUCTING. This warranty does not cover (a) normal maintenance and service or (b) any products or parts which have been subject to misuse, negligence, accident, improper
maintenance or repair (other than by Broan-NuTone), faulty installation or installation contrary to recommended installation instructions.
The duration of any implied warranty is limited to the one-year period as specified for the express warranty. Some states do not allow limitation on how long an implied warranty lasts, so the
above limitation may not apply to you.
BROAN-NUTONE’S OBLIGATION TO REPAIR OR REPLACE, AT BROAN-NUTONE’S OPTION, SHALL BE THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY. BROANNUTONE SHALL NOT BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH PRODUCT USE OR PERFORMANCE. Some states
do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. This warranty supersedes all prior warranties.
To qualify for warranty service, you must (a) notify Broan-NuTone at the address or telephone number below, (b) give the model number and part identification and (c) describe the nature of
any defect in the product or part. At the time of requesting warranty service, you must present evidence of the original purchase date.
BROAN-NUTONE ONE YEAR LIMITED WARRANTY
Broan-NuTone LLC, 926 W. State Street, Hartford, Wisconsin 53027 www.broan.com 800-558-1711
Broan-NuTone Canada, Inc., 1140 Tristar Drive, Mississauga, Ontario L5T 1H9 www.broan.ca 877-896-1119
www.broan.com
99526964D
Loading...