Broan B5736SS, B5730SS Owner’s Manual

SR - N

MODELS B5630SS ,, B5636SS ,, B5730SS ,, B5736SS

I EYC

To register this product visit:

WWW,b roa13,co133

INTENDED FOR DOMESTIC COOKING ONLY,

WARNING WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK, OR INJURY TO PERSON(S) OBSERVE THE

FOLLOWING:

1. Use this unit only in the manner intended bythe manufacturer. If you have questions, contact the manufacturer at the

address or telephone number listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service panel and lock service disconnecting means to prevent

power from being switch on accidentally. When the service disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by qualified personnel in accordance with all applicable codes and standards, including fire-rated construction codes and

standards.

4. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment

to prevent backdrafting. Follow the heating equipment

manufacturer's guidelines and safety standards such as

those published by the National Fire Protection Association

(NFPA), the American Society for Heating, Refrigeration

and Air Conditioning Engineers (ASHRAE) and the local code authorities.

5. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

6. Ducted fans must always be vented to the outdoors.

7. Do not use this unit with any other solid-state speed control device.

8. To reduce the risk of fire, use only steel ductwork.

9. This unit must be gounded.

TO REDUCE THE RISK OF A RANGE TOP GREASE

FIRE:

a) Never leave surface units unattended at high settings.

Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings.

b) Always turn hood ON when cooking at high heat or when

cooking flaming foods (i.e. Cr_pes Suzette, Cherries Jubilee,

Peppercorn Beef Flamb6).

c) Clean ventilating fans frequently. Grease should not be

allowed to accumulate on fan or filters.

d) Use proper pan size. Always use cookware appropriate for

the size of the surface element.

INSTALLER: LEAVE THIS GUIDE TO THE HOMEOWNER.

HOMEOWNER: OPERATION AND MAINTENANCE INFORMATION ON PAGE 8.

TO REDUCE THE RISK OF INJURY TO PERSON(S)

IN THE EVENT OF A RANGE TOP GREASE FIRE,

OBSERVE THE FOLLOWING*:

1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metaltray, then turn offthe burner. BE CAREFU LTO PREVENT BURNS. IFTHE FLAMES DO NOT GOOUT IMMEDIATELY, EVACUATE AND CALL THE FIRE DEPARTMENT.

2. NEVER PICK UP A FLAMING PAN- You may be burned.

3. DO NOT USE WATER, including wet dishcloths or towels - This could cause a violent steam explosion.

4. Use an extinguisher ONLY if:

A. You know you have a Class ABC extinguisher and you

know how to operate it.

B. The fire is small and contained in the area where it

started.

C. The fire department has been called. D. You can fight the fire with your back to an exit.

* Based on "Kitchen Fire Safety Tips" published by NFPA.

CAUTION

1. For indoor use only.

2. For general ventilating use only. Do not use to exhaust

hazardous or explosive materials and vapors.

3. To avoid motor bearing damage and noisy and/or

unbalanced impeller, keep drywall spray, construction dust,

etc. off power unit.

4. Do not use over cooking equipment greater than 60,000

BTU/hr. as the blower motor will shut down intermittantly.

5. Your hood motor has a thermal overload which will automatically shut off the motor if it becomes overheated.

The motor will restart when it will cool down. If the motor continues to shut off and restart, have the hood serviced.

6. The bottom of the hood MUST NOT BE LESS than 30" and at a maximum of 36" above cooktop for best capture of

cooking impurities.

7. Two installers are recommended because of the size of this hood.

8. To reduce risk of fire and to properly exhaust air, be sure to duct air outside. Do not exhaust air into spaces within

walls or ceilings or into attics, crawl spaces, or garages.

9. Be careful when installing the decorative flue and hood, they

may have sharp edges.

10. Please read specification label on product for further information and requirements.

SR - N

MODELS B5630SS • B5636SS • B5730SS • B5736SS

INSTALL THE DUCTWORK Page2 (Ducted Hoods Only) PREPARE THE HOOD

1. Decide where the ductwork will run between the

hood and the outside.

2. A straight, short duct run will

allow the hood to perform most

efficiently.

3. Long duct runs, elbows and transitions

will reduce the performance of

the hood. Use as few of them as possible. Larger ducting may be required for best performance with longer duct runs.

4. Install wall cap or roof cap. Connect round metal ductwork to cap and work back towards the hood location. Use duct tape to seal the joints between ductwork sections.

HOOD

ROOF CAP

DECORATIVE

FLUE

30"TO 36"ABOVE

COOKING SURFACE

DUCT

ROUND ELBOW

MEASURE THE INSTALLATION

ROOF CAP

__'_"'_ _ ROUND ELBOW

6ROONDDUOT --fl

_ WALL CAP

r-F,/

DECORATIVE FLUE _ I _3_,.- m \ HOOD MOUNTING

HOOD II I I t

_ _ _ .J_'/ BRACKET

I_---_ 12 1/2" TO CENTER

Unpack hood and check contents. You should receive: 1 - Hood

1 - Glass Canopy (Models B5630SS & B5636SS) 1 - Metal Canopy (Models B5730SS & B5736SS)

1 - Decorative Flue Assembly 1 - Damper / Duct Connector 1 - Lower Flue Mounting Bracket 1 - Upper Flue Mounting Bracket

1 - Hood Mounting Bracket 2 - Aluminum Grease Filters (installed in hood) 1 - Parts Bag containing:

8 - Mounting Screws (#8 x 3/8" Pan Head) 7 - Mounting Screws (#8 x 1-1/2" Flat Head)

4 - Mounting Screws (M4 x 1.0 Flat Head) 7 - Drywall Anchors

2 - Washers 4 - Decorative Washers

1 - Installation Manual

8 MOUNTING SCREWS

(#8 x 3/8" Pan Head)

_(_M OUNTING

DECORATIVEFLUE

CREWS

4X 1.0"

at Head)

7MOUNTING

SCREWS

(#8X 1-1/2"

FlatHead)

2 WASHERS

3%" -- _ , "

-'- t

30" TO36"ABOVE

COOKING SURFACE *

The minimum hood distance above cooktop MUST NOT BE LESS than 30".

A maximum of 36" above cooktop is highly recommended for best capture of cooking impurities.

Distances over 36" are at the installer and users discretion; providing that the ceiling height permits.

DAMPER/ DUCT

CONNECTOR

4 DECORATIVE

WASHERS

FLUEMOUNTING

BRACKET

LOWER

FLUE MOUNTING

BRACKET

7 DRYWALL

ANCHORS

HOOD

MOUNTING

BRACKET

SR - N

MODELS B5630SS ,, B5636SS ,, B5730SS ,, B5736SS

Page 3

INSTALL THE WIRING

8¼-

1. GROUNDING INSTRUCTIONS This appliance must be grounded. In the event of an

electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This appliance is equipped with a cord having a grounding wire with a grounding plug. The plug must be plugged into an outlet that is properly installed and grounded.

2. Position the electrical outlet within the space covered by the decorative flue and where it will not interfere with the round duct. Make sure the outlet is no further than 8W' from where

the cord exits from the hood and that the outlet does not interfere with a mounting bracket fastening area or where the

decorative flue touches the wall.

INSTALL THE HOOD MOUNTING

BRACKET

.. WALL STUDS

_FRAMING BEHIND_

¢: 4.

t___,....

42__

421A'' = bottom of hood 30" above cooktop 481A'' = bottom of hood 36" above cooktop

1. Construct wood wall framing that is flush with interior surface of wall studs.

Make sure: a) the framing is centered over installation location.

b) the height of the framing will allow the mounting bracket

to be secured to the framing within the dimensions shown.

2. After wall surface is finished, carefully center and level the hood mounting bracket and secure it to wall framing with (3)

#8 x 1-1/2" mounting screws. Tighten the screws completely.

NOTE: On 8-ft. ceilings

Hood distance above cooktop is: Minimum 30", Maximum 36" (for ducted discharge)

Minimum 30", Maximum 33" (for non-ducted discharge) On 9-ft. ceilings

Hood distance above cooktop is: Minimum 31", Maximum 36" (for both ducted and non-ducted discharge)

On lO=ft, ceilings Hood distance above cooktop is: Minimum 31", Maximum 36" (for both ducted and non-ducted discharge).

NOTE: 10-ft. ceilings require 10=ft. Flue Extension, Model FXN56SS for ducted or non=ducted installations (purchase separately).

BR - N

MODELS B5630SS • B5636SS • B5730SS • B5736SS

Page 4

INSTALL UPPER FLUE MOUNTING INSTALL THE HOOD

BRACKET (Horizontally Ducted Hoods Only)

Center of installation Ceiling

Recommended _, _'

distance between 11/8"

screwholes j

....... r---_:---_ ......

': i71/2 i

p< = _! \

i j

i i i

DO NOT REMOVE the protective plastic film covering the decorative flue and the hood at this time.

Lay the back side of the hood flat on a table. Use a piece of cardboard to avoid damaging the table or the hood.

Attach damper / duct connector to top of hood using (4) #8 x 3/8" Pan Head mounting screws.

Remove the grease filters by pulling down the metal latch

tab and tilting filters downward to remove.

Carefully rotate hood upright.

Ceiling • • the ceiling

\ installation

1. Drill two _6" diameter holes where shown. Insert drywall anchors into the holes.

2. Center the bracket over the hood location and flush with the ceiling. Make sure that the slots of the upper flue bracket are

at the bottom. Secure the upper flue bracket to the wall using (2) #8 x 1W' mounting screws.

3. Tighten the screws completely. Make sure that the bracket is tight against the wall.

Center of Flush with

\ /

Upper flue mounting

bracket slots

(_)

LOWER FLUE

MOUNTING BRACKET _---_ I

8W'

MAX.

t _

6. Make sure there will be adequate clearance between top of hood and lower flue mounting bracket for ductwork. Elbow

must be located below lower flue mounting bracket.

7. Align the hood and center it above the hood mounting bracket. Gently lower the hood until it securely engages the

bracket.

i i

INSIDE BACK

OF THE HOOD

SIDE VIEW ;

MOTOR/BLOWER

ASSEMBLY

HOLES LOCATION

8. With the hood hanging in place, drill through the both holes located in the inside lower back of hood using a 5/16" drill

bit. Insert the included drywall anchors into the drilled holes (one for each hole). Install (2) washers and (2) no. 8 x 1W'

mounting screws through the back of the hood and into the drywall anchors. Verify that the hood is centered and leveled.

Tighten all screws completely.

9. Reinstall grease filters by aligning rear filter tabs with slots in the hood. pull down the metal latch tab, push filter into position and release. Make sure filters are securely engaged

after installation.

SR - N

6" ROUND

ELBOW

I I I I

I I

10. Measure and install 6" round steel ductwork to roof cap or wall cap and 900 elbow over duct collar on hood. Use duct

tape to make all joints secure and air tight.

11. Plug hood power cord into the outlet.

LOWER FLUE MOUNTING BRACKET

MODELS B5630SS ,, B5636SS ,, B5730SS ,, B5736SS

Page 5

UPPER FLUE MOUNTING BRACKET

FRONT VIEW

...... ......

UPPER

FLUE

flue mounting bracket. The bracket should be inside the flue.

Secure the upper flue to the upper flue mounting bracket using (2) no. 8 x 3/8" mounting screws.

15.

Remove protective plastic film covering the upper flue and

the hood.

16.

Mount the glass plate or the stainless steel plate on the top of hood base with (4) flat head screws (M4 x 1.0") and (4) decorative washers. Screw from top of hood base. Do not overtighten these screws.

LOWER

FLUE

NOTE: 10-ft. ceilings require 10-ft. Flue Extension, Model FXN56SS for ducted or non=ducted installations (purchase

separately). Discard the upper flue supplied with your hood and replace it with the Model FXN56SS flue extension.

12. Remove the upper flue from inside the lower flue. Install the lower flue bracket to the lower flue using (2) flue bracket screws no. 8 x 3/8'.'Make sure that the slots are at the top. Carefully replace the upper flue inside the lower flue. Remove protective plastic film covering the lower flue only.

13. Carefully place both flues into the recessed area of hood top.

14. Slide the upper flue upward until it is aligned with its upper

INSTALL THE HOOD (Vertically Ducted Hoods Only)

DO NOT REMOVE the protective plastic film covering the decorative flue and the hood at thistime.

Lay the back side of the hood flat on a table. Use a piece of cardboard to avoid damaging the table or the hood.

Attach damper / duct connector to top of hood using (4) #8 x 3/8" Pan Head mounting screws.

Remove the grease filters by pulling down the metal latch

tab and tilting filters downward to remove.

Carefully rotate hood upright.

LOWER FLUE MOUNTING BRACKET

"U" "U"

LOWER

FLUE

NOTE: 10-ft. ceilings require 10-ft. Flue Extension Model FXN56SS (purchase separately). Discard the upper flue

supplied with your hood and replace it with the Model

FXN56SS flue extension.

6. Remove the upper flue from inside the lower flue. Install the lower flue bracket to the lower flue using (2) flue bracket

screws #8 x 3/8", make sure that the slots are at the top. Carefully replace the upper flue inside the lower flue.

Remove protective plastic film covering the lower flue only.

7. Carefully place both flues into the recessed area of hood top.

SR - N

MODELS B5630SS ,, B5636SS ,, B5730SS ,, B5736SS

Page 6

6"ROUND

STEEL DUCT

DUCT LENGTH

DECORATIVE

FLUE

8. Measure and install steel ductwork to hood duct connector. Use duct tape to make all joints secure and air tight.

9. Hold hood up close to wall mounting location and plug power cord into wall outlet.

10.Align the hood and center it above the hood mounting bracket. Make sure ductwork on hood lines up and attaches

to ductwork in ceiling. Gently lower the hood until it securely

engages the bracket.

11. Use duct tape to make all joints secure and air tight.

UPPER FLUE MOUNTING BRACKET

UPPER _ _

FLUE / F

15. Slide the upper flue upward until it is aligned with its mounting bracket. The bracket should be inside the flue. Secure the

upper flue to the upper flue mounting bracket using (2) #8 x 3/8" mounting screws.

16. Remove protective plastic film covering the upper flue and

the hood.

17.

Mount the glass plate or the stainless steel plate to the top of hood base with (4) flat head screws (M4 x 1.0") and (4) decorative washers. Screw from top of hood base. Do not

overtighten these screws.

i i

INSIDE BACK

.............. I

SDE VEW

OF THE HOOD

HOLES LOCATION

MOTOR/BLOWER

ASSEMBLY

12.With the hood hanging in place, drill through both holes located in the inside lower back of hood using a 5/16" drill

bit. Insert the included drywall anchors into the drilled holes (one for each hole). Install (2) washers and (2) #8 x 1-1/2"

mounting screws through the hood back and into the drywall anchors. Verify that the hood is centered and leveled. Tighten all screws completely.

13. Reinstall grease filters by aligning rear filter tabs with slots in the hood. Pull down the metal latch tab, push filter into position and release. Make sure filters are securely engaged

after installation.

14. Slightly push aside the upper flue to avoid any damage while installing the lower flue to the hood top using (2) #8 x 3/8" screws through the lower flue side slots.

INSTALL THE HOOD

(Non-Ducted Hoods Only)

NON=DUCT KIT MODEL RK56 CONTENTS

RECIRCULATION

FILTERS

NON-DUCTED _

NON-DUCT

PLENUM

(ST4 x 8 Round Head)

SCREWS (_

NON-DUCT PLENUM

COLLAR

NOTE: Non=ducted installations require Non=Duct Kit, Model RK56 (purchase separately).

1. CAUTION: Do not use plastic or rigid metal duct.

2. Do not remove the protective plastic film covering the decorative flue and the hood atthis time.

3. Lay the back side of the hood flat on a table. Use a piece of

cardboard to avoid damaging the table or the hood.

4. Attach damper / duct connector to top of hood using (4)

#8 x 3/8" Pan Head mounting screws.

5. Remove damper flaps from damper / duct connector and

discard flaps.

8 MOUNTING

WRAPS "_% FLEXIBLE DUCT

MODELS B5630SS ,, B5636SS ,, B5730SS ,, B5736SS

6. Remove the grease filters

by pulling down the metal latch

tab and tilting filters

downward to remove.

7. Attach non-duct collar to non-duct plenum using (4) ST4 x 8 round head screws.

8. Measure distance "A". This will be the length of the extended flex duct.

9. Attach aluminum

NON-DUCT PLENUM _--_ "--"_T

7/8"

flexible

duct to the damper

6" ALUMINUM F_-''LI I [

/ duct

connector with a tie

wrap.

10. Attach

flexible duct

CONNECTOR _ J_ __Jr_

to non-duct

plenum collar and

secure with

tie wrap.

Tape all joints with

duct tape.

NOTE: lO-ft, ceilings require 104t. Flue Extension, Model FXN56SS for ducted or non-ducted installations (purchase separately). Discard the upper flue supplied with your hood and replace it with the Model FXN56SS flue extension.

LOWER FLUE MOUNTING BRACKET

Page 7

14. Hold hood up close to wall mounting location and plug power cord into wall outlet.

15.Align the hood and center it above the hood mounting bracket. Gently lower the hood until it securely engages the

bracket.

| |

INSIDE BACK

OF THE HOOD

MOTOR/BLOWER

ASSEMBLY

..... s,22V,E.W_.

HOLES LOCATION

16.

With the hood hanging in place, drill through both holes located in the inside lower back of hood using a 5/16" dril

bit. Insert the included drywall anchors into the drilled holes (one for each hole). Install (2) washers and (2) #8 x 1-1/2" mounting screws through the back of the hood and into the drywall anchors. Verify that the hood is centered and leveled.

Tighten all screws completely.

17.

two non-duct

recirculation

filters to sides

of blower by aligning key

Attach(2) I _: _ (__i 1

lock slot and rotating until

filters lock into

place. For replacement non-duct recirculation filters - purchase

S97018030 or ROUNDFILTER.

18.

Reinstall grease filters by aligning rear filter tabs with slots in the hood. Pull down the metal latch tab, push filter into position and release. Make sure filters are securely engaged after installation.

LOWER

FLUE

11. Remove the upper flue from inside the lower flue. Install the lower flue bracket to the lower flue using (2) flue bracket

screws #8 x 3/8", make sure that the slots are at the top. Carefully replace the upper flue inside the lower flue. Remove protective plastic film covering the lower flue only.

12. Carefully place both flues into the recessed area of hood

top.

13.Attach non-duct plenum with collar to upper flue using (4) ST4 x 8 round head screws.

19. Slide up the upper flue until it is aligned with its mounting

bracket. The bracket should be inside the flue. Secure

the upper flue on the upper flue mounting bracket using

(2)#8 x 3/8" mounting screws.

20. Remove protective plastic

film covering the flue and the hood.

21.

Mount the glass plate or the stainless steel plate on the

top of hood base with (4) flat head screws (M4 x 1.0")

and (4) decorative washers. Screw from top of hood base. Do

screws.

UPPER FLUE

MOUNTING BRACKET

FRONT VIEW

UPPER

FLUE

not overtighten these

SR - N

MODELS B5630SS ,, B5636SS ,, B5730SS ,, B5736SS

LIGHT BULBS MAINTENANCE

Grease Filters

O LIGHT BULB COVER

Grease filters should be cleaned monthly. Remove grease filters by pulling down on the metal latch tab. This will disengage the filter from the hood. Tilt the filter downward and

remove. To clean all-metal filters: Use a warm detergent solution or

put them in the dishwasher using a non-phosphate detergent. Discoloration of the filter may occur if using phosphate

detergent or as a result of local water conditions - but this will not affect filter performance. This discoloration is not covered by the warranty.

Page 8

WARNING

Bulbs may be hot. Always allow bulbs to cool down before removing them.

This range hood requires two halogen bulbs (Type JC, 12V, 20W Max, G-4 Base).

To change bulbs:

1. Remove light bulb cover by gently pushing it upward and turning it counterclockwise.

2. Replace bulb.

3. Re-install light bulb cover by gently pushing it upward and turning it clockwise.

OPERATION

OFF

LOW MED.

FAN CONTROLS

The hood is operated using the push buttons on the front panel. Push the light button to turn the lights on and off.

Push the fan controls to select low, medium, or high blower speed.

Push the OFF button to turn the blower off.

HIGH

LIGHT

ON/OFF

Non-Duct Recirculation Filters Change the non-duct recirculation filters every 6 months.

Rotate the filters to remove them from the blower and replace.

Hood Cleaning How to maintain the bright look of stainless steel and help

prevent corrosion. Dos:

Once a month, wash surfaces with clean cloth or rag soaked with warm water and mild soap or liquid dish detergent.

Always clean in the direction of original polish lines. Always rinse well with clear water (2 or 3 times) after

cleaning. Wipe dry completely. You may also use a specialized household stainless steel

cleaner.

Oon'ts:

Do not use any steel or stainless steel wool or any other scrapers to remove stubborn dirt.

Do not use any harsh or abrasive cleansers. Do not allow dirt to accumulate.

Do not let plaster dust or any other construction residues reach the hood. During construction or renovation, cover the

hood to make sure no dust sticks to stainless steel surface.

Avoid: when choosing a detergent

Any cleaners that contain bleach will attack stainless steel. Any products containing : chloride, fluoride, iodide,

bromide will deteriorate surfaces rapidly. Any combustible products used for cleaning such as

acetone, alcohol, ether, benzol, etc., are highly explosive and should never be used close to a range.

SR - N

MODELS B5630SS • B5636SS • B5730SS • B5736SS

SERVICE PARTS Page9

KEY PARTNO. DESCRIPTION QTY.

1 $99526973 Decorative Upperand Lower Flues 1 2 $99526974 Motor / BlowerAssembly 1 3 $99526975 Light Socket Assembly 2 4 $99527010 Light Trim Ring / Lens Assembly 2 5 $99526976 Push Button Assembly 1 6 $97018029 Aluminum GreaseFilters (pair) 2 7 $97018030 Non-Duct Recirculation Filters (pair) 2 8 $99526981 Curved GlassPlate (B5630SS) 1

$99527024 Curved GlassPlate(B5636SS) 1 $99526982 Curved Metal Platewith Rail (B5730SS) 1 $99527025 Curved Metal Platewith Rail (B5736SS) 1

9 $99526983 Damper / Duct Connector 1

10 $99526984 6" Dia.ExpandableFlexibbAluminum Duct 1 11 $99526985 Non-Duct Plenum Assembly 1 12 $99526987 Hood Mounting Bracket 1 13 $99526989 Lower FlueMounting Bracket 1 14 $99526991 Upper FlueMounting Bracket 1

S99527011 Transformer(notshown) 1

$99527012 Capacitor (not shown) 1

$99527013 PlasticCover(notshown) 1

$99526994 Parts Bag (not shown) 1

Orderservice parts by Part No.- not byKeyNo.

""-10

WIRING DIAGRAM

s_op io_ Fd hig_ I_mp

I HALOGENLIGHTS

............ih

TO MOTOR_

Replacement parts can be ordered on our website:

www.broan.com

WARRANTY

Broan-NuTone warrants to the original consumer purchaser of its products that such products will be free from defects in materials or workmanship for a period of oneyear from the date of original purchase. THERE ARE NO OTHER WARRANTIES, EXPRESSOR IMPLIED, INCLUDING, BUT NOTLIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FORA

PARTICULARPURPOSE. During this one-year period, Broan-NuTone will, at its option, repair or replace, without charge, any product or part which is found to be defective under normal use and service.

THIS WARRANTY DOESNOT EXTENDTO FLUORESCENTLAMP STARTERS,TUBES, HALOGENAND INCANDESCENTBULBS,FUSES,FILTERS, DUCTS,ROOFCAPS, WALL CAPSAND OTHER ACCESSORIESFORDUCTING.This warranty does not cover (a) normal maintenance and service or (b) any products or parts which havebeen subject to misuse, negligence, accident, improper

maintenance or repair (other than by Broan-NuTone), faulty installation or installation contrary to recommended installation instructions. The duration of any implied warranty is limited to the one-year period as specified for the express warranty. Somestates do not allow limitation on how long an implied warranty lasts, so the above limitation may not apply to you.

BROAN-NUTONE'SOBLIGATIONTO REPAIR ORREPLACE,AT BROAN-NUTONE'SOPTION, SHALL BETHE PURCHASER'SSOLEANDEXCLUSIVEREMEDY UNDERTHIS WARRANTY. BROAN- NUTONESHALL NOT BELIABLE FOR INCIDENTAL, CONSEQUENTIALORSPECIAL DAMAGESARISING OUT OFOR IN CONNECTIONWITH PRODUCT USEOR PERFORMANCE.Some states

do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. This warranty supersedes all prior warranties. To qualify for warranty service, you must (a) notify Broan-NuTone at the address or telephone number below, (b) give the model number and part identification and (c) describe the nature of any defect in the product or part. At the time of requesting warranty service, you must present evidence of the original purchase date.

BROAN-NUTONEONEYEAR LIMITED WARRANTY

Broan-NuTone LLC, 926 W. State Street, Hartford, Wisconsin 53027 www.broan.com 800-558-1711

Broan-NuTone Canada, Inc., 1140 Tristar Drive, Mississauga, Ontario L5T 1H9 www.broan.ca 877-896-1119

99526963C

+ 19 hidden pages