Broan B5630SS Specifications
B56 & B57 SERIES
RANGE HOODS
SPECIFICATION SHEET
Gently curving glass or metal
canopy creates a dramatic,
contemporary appearance and an
open, airy feel.
FEATURES
Wall mount
•
Finish: 430 Stainless Steel #4 Brushed
•
Widths: 29-1/2”, 35-7/16”
•
Telescopic flue accommodates 8’ to 9’
•
ceilings
6” round duct connector/backdraft
•
damper
Convertible to non-ducted operation -
•
requires Model RK56 (sold separately)
Halogen lighting (2 x 20 watt, 12V, Type
•
JC 12V 20W G4 Base) (bulbs included)
5 push-button controls: blower on-off,
•
blower low speed, blower medium
speed, blower high speed, light on-off
Single centrifugal blower
•
Dishwasher-safe filter features a quick-
•
release latch
Cord-connected
•
SPECIFICATIONS
VOLTS AMPS CFM SONES DUCT
120 3.3
200 (low) 2.5 (low)
10-7/8”
12”
450 (high) 8.5 (high)
HVI-2100 CERTIFIED RATINGS comply with new testing
technologies and procedures prescribed by the Home
Ventilating Institute, for off-the-shelf products, as they are
available to consumers. Product performance is rated
at 0.1 in. static pressure, based on tests conducted in
a state-of-the-art test laboratory. Sones are a measure
of humanly-perceived loudness, based on laboratory
measurements.
10-7/8”
6” round
12”
OPTIONS
Replacement grease filters available
•
Flue extension for 10’ ceiling (Model
•
FXN56SS) (32-3/8” long) (ducted or
non-ducted)
Replacement non-ducted recirculating
•
filters available (Model ROUNDFILTER)
Broan-NuTone LLC Hartford, Wisconsin www.broan.com 800-558-1711
REFERENCE QTY. REMARKS Project
Location
Architect
Engineer
Contractor
Submitted by Date
Min. 24” Ducted, 27“ Non-ducted (8-ft. ceiling)
Min. 36” Ducted / Non-Ducted (9-ft. ceiling)
Max. 30” Ducted / Non-Ducted (8-ft. ceiling)
Max. 41” Ducted / Non-Ducted (9-ft. ceiling)
29-1/2”, 35-7/16”
B56 Series
19-3/4”
90C 99044484B
Min. 24” Ducted, 27“ Non-ducted (8-ft. ceiling)
Min. 36” Ducted / Non-Ducted (9-ft. ceiling)
Max. 30” Ducted / Non-Ducted (8-ft. ceiling)
Max. 41” Ducted / Non-Ducted (9-ft. ceiling)
29-1/2”, 35-7/16”
B57 Series
19-3/4”
B56 & B57 SERIES WIRING
1. GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of an electrical short circuit, grounding
reduces the risk of electric shock by providing an escape wire for the electric current. This
appliance is equipped with a cord having a grounding wire with a grounding plug. The plug
8¼”
MAX.
must be plugged into an outlet that is properly installed and grounded.
2. Position the electrical outlet within the space covered by the decorative flue and
where it will not interfere with the round duct. Make sure the outlet is no further
than 8¼” from where the cord exits from the hood and that the outlet does not
interfere with a mounting bracket fastening area or where the decorative flue touches the wall.
B56 & B57 SERIES MOUNTING
1. Construct wood wall framing that is flush with interior surface of wall studs.
Make sure:
a) the framing is centered over installation location.
b) the height of the framing will allow the mounting bracket
to be secured to the framing within the dimensions
shown.
2. After wall surface is finished, carefully center and level the hood
mounting bracket and secure it to wall framing with (3) #8 x 1-1/2”
mounting screws. Tighten the screws completely.
NOTE:
On 8-ft. ceilings
Hood distance above cooktop is:
Minimum 30”, Maximum 36” (for ducted discharge)
Minimum 30”, Maximum 33” (for non-ducted discharge)
On 9-ft. ceilings
Hood distance above cooktop is:
Minimum 31”, Maximum 36” (for both ducted and non-ducted
discharge)
On 10-ft. ceilings
Hood distance above cooktop is:
Minimum 31”, Maximum 36” (for both ducted and non-ducted
discharge).
NOTE: 10-ft. ceilings require 10-ft. Flue Extension, Model FXN56SS
for ducted or non-ducted installations (purchase separately).
CEILING DUCT HOOD DISTANCE ABOVE 36” COOK TOP (SEE NOTE 1)
HEIGHT METHOD 30” 31” 32” 33” 34” 35” 36”
MOUNTING BRACKET LOCATION ABOVE 36” HIGH COOK TOP
8 FEET
9 FEET DUCTED OR 43-1/2” 44-1/2” 45-1/2” 46-1/2” 47-1/2” 48-1/2”
10 FEET DUCTED OR
NONDUCTED 43-1/2” 44-1/2” 45-1/2” 46-1/2” 47-1/2” 48-1/2”
WITH FXN56SS
DUCTED 42-1/2” 43-1/2”
NONDUCTED 42-1/2” 43-1/2”
NONDUCTED
44-1/2”
44-1/2”
45-1/2”
45-1/2”
46-1/2”
47-1/2”
WALL STUDS
FRAMING BEHIND
421⁄2” = bottom of hood 30” above cooktop
481⁄2” = bottom of hood 36” above cooktop
48-1/2”
DRYWALL
C
L
9”
19⁄16”
41⁄2”
MOUNTING BRACKET
LOCATION
(ABOVE 36” HIGH
COOKTOP)
NOTES:
1. Minimum hood distance above cooktop must not be less than 30”.
A maximum of 36” above the cooktop is highly recommended for best capture of cooking impurities.
Distances over 36” above the cooktop are at the installer’s and user’s discretion - providing that ceiling height and flue length permit.
Broan-NuTone LLC Hartford, Wisconsin www.broan.com 800-558-1711
Loading...