Breville BDC650 User Manual

Breville Consumer Support

the Grind Control

™

Instruction Book - Manuel d’instructions

USA

Mail: Breville USA

19400 S. Western Ave Torrance CA 90501-1119

Phone: 1-866-273-8455 1-866-BREVILLE

Web:

brevilleusasupport.com

www.breville.com

Breville is a registered trademark of Breville Pty. Ltd. A.B.N. 98 000 092 928.

Due to continued product improvement, the products illustrated/photographed

in this book may vary slightly from the actual product.

Canada

Mail: Breville Canada

3595 Boulevard Cote-Vertu, Saint-Laurent, Québec H4R 1R2

Phone:

Email:

1-855-683-3535

askus@breville.ca

BDC650 USC C15

BDC650

CONGRATULATIONS

CONTENTSCONTENTS

4 Breville recommends safety ﬁrst

8 Know your Breville product

on the purchase of your Breville product

and exclusive offers.

10 Operating your Breville product

12 Using the Grind Control™

- Carafe Mode

15 Using the Grind Control™

- Single Cup Mode

17 Programming the Clock &

Auto Start

20 Advanced Features 21 Helpful Tips

23 Care & cleaning

27 Troubleshooting

34 French

USA Consumers: www.brevilleusa.com Canadian Consumers: www.breville.ca

*Registering is not a substitute for proof of purchase when submitting a Warranty Claim.

BREVILLE RECOMMENDS SAFETY FIRST BREVILLE RECOMMENDS SAFETY FIRSTBREVILLE RECOMMENDS SAFETY FIRSTBREVILLE RECOMMENDS SAFETY FIRST BREVILLE RECOMMENDS SAFETY FIRST

At Breville we are very safety conscious. We design and manufacture consumer products with the safety of you, our valued customer, foremost in mind. In addition we ask that you exercise a degree of care when using any electrical appliance and adhere to the following precautions.

IMPORTANT SAFEGUARDS

READ ALL INSTRUCTIONS

• Carefully read all instructions

before operating the appliance and save for future reference.

• Remove and safely discard

any packaging material, plastic power plug cover, and any removable labels before using appliance.

• If the appliance is to be:

- left unattended

- cleaned

- moved

- assembled; or

- stored unplug the unit from the power outlet.

• Always operate the appliance

on a stable and heat resistant surface.

• Do not place the appliance

on or near a hot gas burner, electric element or where it could touch a heated oven.

• Ensure the unit has at least

4 inches (10cm) of clearance from all side panels.

• Do not operate the appliance

without water in the water tank. Use only cold, preferably ﬁltered water. Do not ﬁll the appliance with any other liquids.

• Ensure the supplied gold tone

ﬁlter or a paper ﬁlter (8-12 cup, ﬂat base basket style with ~ 3¼"/8.25cm base) is placed in the coffee basket before using the appliance. Do not use the gold tone ﬁlter in conjunction with a paper ﬁlter.

• Before starting a brew cycle:

- Completely empty the carafe and securely lock the carafe lid in place.

- Push in and seat the carafe under the drip stop.

- Ensure the ﬁlter basket is empty and properly ﬁt in place.

During a brew cycle:

- Do not remove the carafe or open the basket door while the unit is in a brew cycle. Failure to follow the above may lead to scalding or serious injury.

• Some surfaces may be hot,

use caution when touching or lifting the unit or accessories.

• Only lift the carafe from the

carafe handle.

• The carafe is designed for

use with this appliance only. It must never be used on a range top or in a microwave.

• Scalding may occur if the

carafe lid is removed during the brewing cycle.

• Always ensure the carafe

lid is securely locked in place onto the carafe before pouring.

• Do not use the carafe with a

cracked, loose, weakened or damaged handle.

• Do not touch hot surfaces.

Use the handle for lifting and carrying the carafe.

• Do not set a hot carafe on a

wet, cold or heat sensitive surface.

• Do not operate the grinder

without the bean hopper lid in position. Keep ﬁngers, hands, hair, clothing and utensils away from the bean hopper during operation. Avoid contact with moving parts.

• Check the grinder for

presence of foreign objects before using.

• Use the grinder to grind

roasted coffee beans only.

• Always switch the appliance

off by removing the power plug from the power outlet before attempting to move the appliance, when the appliance is not in use and before cleaning and storing. Allow to cool before putting on or taking off parts, and before cleaning the appliance.

• Do not use harsh or abrasive

materials when cleaning any part of this appliance such as steel wool or scoring pads.

• The use of attachments

not sold or recommended by Breville may cause ﬁre, electric shock or injuries.

4 5

BREVILLE RECOMMENDS SAFETY FIRST BREVILLE RECOMMENDS SAFETY FIRSTBREVILLE RECOMMENDS SAFETY FIRST

IMPORTANT SAFEGUARDS FOR ALL ELECTRICAL APPLIANCES

• Fully unwind cord before use.

• To protect against electric

shock, do not immerse cord, plug or appliance in water or any other liquid.

• Do not let the cord hang over

• It is recommended to

regularly inspect the appliance. Do not use the appliance if the power supply cord, power plug, or appliance becomes damaged in anyway. Immediately stop using the unit and call Breville Consumer Service.

the edge of a bench or table, touch hot surfaces, or become knotted.

• Do not leave the appliance

unattended when in use.

• Children should be

supervised to ensure they do not play with the appliance.

CAUTION

We recommend using cold, ﬁltered water. We do not recommend the use of de-mineralized or distilled water as this may affect the taste of brewed coffee and how the coffee machine is designed to function.

• This appliance is

recommended for household use only. Do not use this appliance for anything other than its intended use. Do not use in moving vehicles or boats. Do not use outdoors.

FOR HOUSEHOLD USE ONLY SAVE THESE INSTRUCTIONS

SHORT CORD INSTRUCTIONS

Your Breville appliance is ﬁtted with a short power cord to reduce the risk of personal injury or property damage resulting from pulling, tripping

BREVILLE ASSIST‰ PLUG

Your Breville appliance comes with a unique Assist

‰

Plug, conveniently designed with a ﬁnger hole to easy removal from the power outlet.

or becoming entangled with a

power cords or extension cords are available and may be used if

longer cord. Longer detachable

CALIFORNIA PROPOSITION 65:

(Applicable to California residents only).

care is exercised. If an extension cord is used, (1) the marked electrical rating of the cord set or extension cord should be at least as great as the electrical rating

This product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.

of the appliance, (2) the cord should be arranged so that it will not drape over the counter-top or table where it can be pulled on by children or tripped over unintentionally and (3) the extension cord must include a 3-prong grounding plug.

NOTE

This appliance has a three wire grounded plug. To reduce the risk of electric shock, this plug will ﬁt in a polarized outlet only one way. If the plug does not ﬁt properly into the outlet, contact a qualiﬁed electrician. Do not use an adaptor or modify the plug in any way. Do not connect the appliance to an external switch or device (such as a timer, monitor or remote circuit) that can be switched on and off.

6 7

KNOW YOUR BREVILLE PRODUCT KNOW YOUR BREVILLE PRODUCTKNOW YOUR BREVILLE PRODUCT KNOW YOUR BREVILLE PRODUCT

All parts of the Grind Control™ that come into contact with coffee and water are BPA Free.*

1 2 3 4 5 7 8 9

1. Bean Hopper Lid

2. 0.5lb Bean Hopper

3. Bean Hopper Locking System seals the

base of the bean hopper for easy removal and transfer of coffee beans for storage.

4. Grind Adjustment Knob, adjusts

coarseness and/or ﬁneness from one of the 6 settings.

5. Cleaning Brush for cleaning of the

grinding burrs and coffee grinds chute.

6. Integrated Adjustable Burr Grinder

grinds whole beans just prior to brewing for maximum ﬂavor and aroma. Grinder can be turned off when using pre-ground coffee.

7. 12-Cup (60oz) Water Tank with

ﬂip-top lid for convenient, front-access ﬁlling. Grille prevents large debris from entering the tank while the ‘MAX’ level ﬂoat rises when the tank is full.

14 15 16 17

8. Intuitive simple to operate Control

Panel with backlit LCD screen.

9. Coffee Grinds Chute delivers ground

coffee from the grinder to the coffee basket.

10. Removable Grinds Catcher catches

loose grinds.

11. Carafe Lid.

12. 12-Cup Double-Wall, Stainless Steel

Thermal Carafe

13. Removable Gold Tone Filter

14. Soft Opening, Swing-Out Door with

safety interlock system prevents operation if the coffee basket is not correctly assembled or the door is not properly closed.

15. Removable Coffee Basket lifts out for

easy ﬁlling and cleaning. Holds the included gold tone ﬁlter or paper ﬁlters.

19 24

OPEN

EXIT

CUP CARAFE

STRENGTH

AUTO

START

START CANCEL

20 21 23 23

16. Steam Bafﬂe diverts water overﬂow if

the coffee basket becomes blocked.

17. Brew Pause Drip Stop temporarily

ceases the ﬂow of coffee when the carafe is removed so a cup can be poured mid-brew.

18. Drip Tray can be removed for direct

brewing into tall cups & travel mugs.

19. OPEN button. Press to open the

swing-out door.

21. CUP | CARAFE button. Press to brew

a single cup of coffee or a carafe.

22. STRENGTH button. Rotate to select

from one of the 8 strength settings, or Pre-ground.

23. Auto Start button

Allows you turn the Auto Start feature On & Off & adjust Auto Start time.

24. START | CANCEL button

Press to start or cancel the brew cycle.

20. MENU | EXIT button

Access the Menu to allow you:

- Set the clock

- Adjust the Alert volumes

- Reset the machine

- Enter the Calibration Mode

8 9

OPERATING YOUR BREVILLE PRODUCT OPERATING YOUR BREVILLE PRODUCTOPERATING YOUR BREVILLE PRODUCT OPERATING YOUR BREVILLE PRODUCT

FRESH IS BEST

To get the most out of your Grind Control™ coffee brewer we recommend using quality freshly roasted whole bean coffee & grind right before you brew. Coffee is at its peak ﬂavor potential 5-20 days after roasting. Always buy coffee with a “Roasted On” date printed on the bag and avoid buying coffee with a “Best Before” or “Use By” date, as you never know when it was roasted. Coffee loses ﬂavor and its aromatics once it’s ground, so grinding right before you brew is the key to great tasting coffee with superior ﬂavor and aroma.

PRODUCT OVERVIEW

Your Grind Control™ coffee brewer is the ﬁrst drip coffee maker with an adjustable built-in grinder and calibration mode.

The adjustable grinder features machined stainless steel burrs that allow you to adjust the coarseness or ﬁneness to optimize ﬂavor balance.

The calibration mode allows you adjust the amount of coffee delivered on any strength/ cup size setting to suit coffee of varying grind size, origins, age and degree of roast, so you can achieve the maximum ﬂavor potential from any coffee you choose.

The Grind Control™ also allows you to brew a single cup or travel mug in “cup” mode or from 2 to 12 cups in “carafe” mode.

BEFORE FIRST USE

Unpack all parts and accessories before removing and safely discarding all packaging material and promotional labels. Ensure the power cord is unplugged from the power outlet.

Wipe the exterior stainless steel housing with a soft, damp cloth. Wash the bean hopper and lid, coffee basket, gold tone ﬁlter and carafe in warm, soapy water and a soft cloth. Do not use abrasive cleansers, pads or cloths which can scratch the surface. Rinse and dry thoroughly.

INITIAL SET UP

1. Install the Bean Hopper

Position the hopper onto the machine. Turn the locking knob clockwise in the direction of the LOCK arrow until it clicks. Fill the hopper with fresh beans.

We recommend always keeping the hopper full (0.5lb maximum) to ensure there are sufﬁcient beans. However, never over-pack the hopper as this may result in the grinder jamming. Replace the hopper lid.

NOTE

For easy removal, transfer and storage of beans, the hopper can be removed by turning the locking knob counterclockwise in the direction of the UNLOCK arrow. If you have removed the hopper, ensure it is securely reassembled back onto the machine. The safety interlock system will prevent operation if the hopper is incorrectly assembled. The LCD screen will ﬂash ‘LOCK BEAN HOPPER’ until the issue is resolved.

2. Plugging in the Power Cord

Unwind the power cord completely and insert the power plug into a grounded 110-120V power outlet. The LCD screen will illuminate.

NOTE

The coffee machine will enter POWER SAVE mode after remaining idle for 10 minutes. Press any button to exit POWER SAVE mode and re-start the machine.

3. Install the Coffee Basket

For best results, we recommend pre-heating the coffee basket by running it under hot tap water. Dry the coffee basket thoroughly, taking particular care to completely dry the chute area. Line the coffee basket with either the provided gold tone ﬁlter or a paper ﬁlter. Never use both at the same time.

a) Provided gold tone ﬁlter. When using

the gold tone ﬁlter, be sure that the handle is positioned towards the hinge area of the coffee basket. Otherwise the handle may interfere with the ﬂow of ground coffee into the gold tone ﬁlter.

HANDLE TOWARDS

COFFEE BASKET HINGE

ENSURE CHUTE

AREA IS

COMPLETELY DRY

NOTE

The gold tone ﬁlter will allow some ﬁne coffee grounds to fall into the coffee. This will appear as sediment in the cup or carafe. This is normal.

Only use the gold tone ﬁlter provided as others may cause the machine to overﬂow.

b) Paper ﬁlter Use an 8-12 cup, ﬂat base

basket style paper ﬁlter with ~ 3¼"/8.25cm base. Ensure that the paper ﬁlter is completely open and touching the side walls and bottom of the coffee basket.

Close the coffee basket lid. Press the OPEN button to open the swing-out door. Attach the coffee basket to the swing-out door by ensuring the hinge area of the coffee basket is ﬁrmly seated in its most downward position on the two door hooks. Close the door until it clicks shut.

CLICK

NOTE

The safety interlock system will prevent operation if the coffee basket is not in place, if it is not ﬁrmly seated on the two door hooks, or if the swing-out door is not closed. The LCD screen will ﬂash ‘EMPTY COFFEE FILTER’ until the issues are resolved.

10 11

OPERATING YOUR BREVILLE PRODUCT OPERATING YOUR BREVILLE PRODUCTOPERATING YOUR BREVILLE PRODUCTOPERATING YOUR BREVILLE PRODUCT

USING THE GRIND CONTROL™

- CARAFE MODE First Time Use Only

We recommend ﬂushing the machine to remove any dust particles or residue from the manufacturing process. Follow the proceeding instructions, ensuring to completely ﬁll the water tank. Step 1 (below) , select ‘12 CUPS’. (Step 2, below) and the ‘PRE-GROUND’ coffee setting. (Step 4, page 13). However do not add any coffee to the coffee basket. Once the cycle is complete, discard the water from the carafe and repeat the cycle again for best results. The machine is now ready to use.

1. Fill the Water Tank

Press the ﬂip-top lid to open. Pour the desired amount of cold, preferably ﬁltered water into the tank using a jug or the provided carafe.

Never use Distilled, De-mineralized or highly ﬁltered water as this will affect the electronics and the taste of your coffee.

If using the carafe, ensure the carafe is clean and the carafe lid is securely locked in place. The LCD screen will indicate the amount of water in the tank as it is ﬁlled. The machine will beep when full and the water level ﬂoat will rise to indicate the maximum level. Do not exceed the 12 cup maximum. Doing so may cause the carafe to overﬂow or water spillage at the back of the machine. Close the ﬂip-top lid.

NOTE

Always ensure your carafe is clean before brewing. Residual coffee will affect the taste of your next cup.

NOTE

Check the water level on the LCD screen before use. We recommend always keeping the water tank full. The water tank should be reﬁlled with cold, preferably ﬁltered water. Never ﬁll with de-mineralized water or any other liquid.

NOTE

Never pour water into the bean hopper or grinding chamber area. Doing so can cause the grinder to clog. Only re-commence use when the grinding chamber and grinding burrs are completely dry. Refer to Troubleshooting, ‘Moisture clogging grinder’, page 26.

NOTE

Never ﬁll the water tank once the coffee machine has started a brewing cycle. This will affect the volume dispensed into the carafe.

2. Pre-Warm the Carafe

A warm carafe will help maintain the coffee’s optimal temperature and keep coffee hotter for longer. Remove the carafe lid by turning counter-clockwise then lifting upwards.

Fill the carafe with hot water and leave to stand for about 30 seconds then discard the water. To lock the carafe lid back into position, align the arrow on the carafe lid with the ALIGN arrow on the carafe. Turn clockwise until the arrow on the carafe lid aligns with the LOCK arrow on the carafe. This ensures that the lid is closed and in the proper position for brewing and pouring. Place the carafe into position under the drip stop outlet.

ALIGN ARROWS THEN TURN TO LOCK

NOTE

Ensure the carafe is clean and completely empty and the lid is securely locked in place before placing under the drip stop outlet. Starting a brew cycle with water or coffee in the carafe will cause the carafe to over ﬂow.

3. Select ‘Carafe’ Mode

Press the CUP|CARAFE button. The LCD screen will display a Carafe symbol and the current number of cups selected. Rotate the CUP | CARAFE dial to select the required number of cups to brew. You can choose less than the current tank level (2 cup minimum), while the maximum is the amount of water in the tank, up to 12 cups. If you select cups greater than the level in the water tank, the LCD will display FILL TANK and the water tank symbol will ﬂash.

4. Select the Brew Strength or

‘PRE-GROUND’ Coffee Setting

There are 8 Strength settings. The LCD screen will display the current strength setting. Rotate the STRENGTH dial to select your required Strength. 1 is the weakest and 8 is the strongest. We recommend starting on setting 4 for a medium strength coffee. Adjust strength higher or lower to suit your taste.

NOTE

If using pre-ground coffee, rotate the STRENGTH dial to select the ‘PRE-GROUND’ coffee setting. This will disable the burr grinder. Add pre- ground coffee to the gold tone ﬁlter or a paper ﬁlter.

We recommend 1 level tablespoon of pre-ground coffee per 5oz/150ml cup of water. Adjust the amount according to your individual taste. The maximum capacity for pre-ground coffee is 12 level tablespoons. Exceeding this amount may cause overﬂow.

5. Start the Brew Cycle

Press the START | CANCEL button. The grinder will commence grinding the correct amount of coffee for the selected brew size and strength. If the ‘PRE-GROUND’ coffee setting has been selected, the grinder will be disabled.

NOTE

Steam may emit from the rear steam vent during grinding and brewing. This is normal.

12 13

OPERATING YOUR BREVILLE PRODUCT OPERATING YOUR BREVILLE PRODUCTOPERATING YOUR BREVILLE PRODUCTOPERATING YOUR BREVILLE PRODUCT

The count-down timer will then begin. The time displayed is an estimate only and will depend on the brew size and strength settings you have selected.

The LCD screen will display:

a) ‘PRE-HEATING’ as the water is heated

to the optimal temperature. The preheating time will depend on the starting temperature of the water in the water tank.

b) ‘INFUSING’ as the water is delivered to

the ground coffee.

c) ‘BREWING’ as the coffee is dispensed into

the carafe.

To stop the cycle at any time, press the START | CANCEL button. You will hear a winding noise. This is normal.

CAUTION

Never open the swing-out door and remove the coffee basket while brewing. Hot water and coffee can cause injury.

The coffee basket and gold tone or paper ﬁlter may still be very hot after brewing. Use caution and allow to cool before removing.

Hot steam may rise when pouring. The bottom of the carafe is hot to touch for several minutes after brewing. Use caution and ensure not to set the carafe on a heat sensitive surface.

6. Using the Brew Pause Feature

The Brew Pause feature temporarily ceases the ﬂow of coffee when the carafe is removed so a cup can be poured mid-brew. Do not remove the carafe for longer than 20 seconds or the coffee may overﬂow the coffee basket.

7. Empty the Coffee Basket

Once the brewing cycle is complete, the ready signal will sound and a winding noise will be heard. This is normal. The coffee machine will automatically shut-off and the LCD screen will ﬂash ‘EMPTY COFFEE FILTER’ as a reminder to remove the coffee basket and discard the used grinds. Wash the coffee basket, taking particular care to rinse the chute area. Then dry the coffee basket and chute area thoroughly.

We also recommend checking the coffee grinds chute disc for any build-up of coffee grinds. This is the stainless steel disc that is visible when the swing-out door is opened.

A build-up of grinds on this disc can affect the performance of the machine. Wipe the disc clean then dry thoroughly.

8. Pour and Enjoy

Ensure the carafe lid is securely locked in position. There is no need to turn or adjust the lid before pouring. The lid automatically opens when pouring so as to keep coffee hot.

USING THE GRIND CONTROL™

- SINGLE CUP MODE

1. Fill the Water Tank

Press to open the ﬂip-top lid. Pour the desired amount of cold, preferably ﬁltered water into the tank using a jug or the carafe. Never use

Distilled, De-mineralized or highly ﬁltered water as this will affect the electronics and the taste of your coffee.

The LCD screen will indicate the amount of water in the tank as it is ﬁlled. The machine will beep when full and the water level ﬂoat will rise to indicate the maximum level. Do not exceed the 12 cup maximum. Doing so may cause water spillage at the back of the machine. Close the ﬂip-top lid.

NOTE

Check the water level on the LCD screen before use. We recommend always keeping the water tank full. The water tank should be reﬁlled with cold, preferably ﬁltered water. Do not ﬁll with any other liquid.

NOTE

Never ﬁll the water tank once the coffee machine has started a brewing cycle. This will affect the volume dispensed into the cup.

2. Pre-Warm the Cup or Travel Mug

A warm cup will help maintain the coffee’s optimal temperature and keep coffee hotter for longer. Fill the cup with hot water for about 30 seconds then discard the water. Place the cup into position under the drip stop outlet.

TIP

For taller cups and travel mugs, remove the drip tray at the base of the machine. Press the OPEN button to open the swing-out door. Insert the cup/mug into the drip tray cavity before closing the swing-out door. The maximum cup/ mug dimensions are 7.5" height, 2¾" diameter.

REMOVE DRIP TRAY, OPEN DOOR,

INSERT CUP, CLOSE DOOR.

14 15

OPERATING YOUR BREVILLE PRODUCT OPERATING YOUR BREVILLE PRODUCTOPERATING YOUR BREVILLE PRODUCTOPERATING YOUR BREVILLE PRODUCT

3. Select ‘Single Cup’ Mode

Press the CUP|CARAFE dial until the LCD screen displays the CUP symbol and the current cup size selected in ounces. Rotate the CUP|CARAFE dial to select the required size.

There are 7 size options to accommodate for different amounts or milk, half-and- half and creamer. Always ensure your cup is an adequate size for the setting selected.

The amounts displayed on the LCD screen are approximate only. Actual amounts may vary depending on the type of ﬁlter used, the coffee grind size, roast, blend and freshness, or amount and type of pre-ground coffee used.

4. Select the Brew Strength or ‘PRE-GROUND’ Coffee Setting

There are 8 strength settings. The LCD screen will display the current strength setting. Rotate the STRENGTH dial to select your required strength. 1 is the weakest and 8 is the strongest. We recommend starting on setting 4 for a medium strength coffee. Adjust strength higher or lower to suit your taste.

NOTE

If using pre-ground coffee, select the ‘PRE-GROUND’ coffee setting. This will disable the grinder. Add pre-ground coffee to the gold tone ﬁlter or a paper ﬁlter. We recommend 1 level tablespoon of pre-ground coffee per 5oz/150ml cup of water. Adjust the amount according to your individual taste. The maximum capacity for pre-ground coffee is 12 level tablespoons. Exceeding this amount may cause overﬂow.

16 17

5. Start the Brew Cycle

NOTE

Steam may emit from the rear steam vent during grinding and brewing. This is normal.

The count-down timer will then begin. The time displayed is an estimate only and will depend on the amount and strength settings you have selected. The LCD screen will display:

a) ‘PRE-HEATING’ as the water is heated

to the optimal temperature. The pre-heating time will depend on the starting temperature of the water in the water tank.

b) ‘INFUSING’ as coffee and water are

steeped together.

c) ‘BREWING’ as the coffee is dispensed

into the cup.

To stop the cycle at any time, press the START | CANCEL button. You will hear a winding noise. This is normal.

CAUTION

Never open the swing-out door and remove the coffee basket while brewing. Hot water and coffee can cause injury.

6. Empty the Coffee Basket

Once the brewing cycle is complete, the ready signal will sound and a winding noise will be heard. This is normal.

The coffee machine will automatically shut-off, however the LCD screen will ﬂash ‘EMPTY COFFEE FILTER’ as a reminder to remove the coffee basket and discard the used grinds. Wash the coffee basket, taking particular care to rinse the chute area. Then dry the coffee basket and chute area thoroughly.

We also recommend checking the coffee grinds chute disc for any build-up of coffee grinds. This is the stainless steel disc that is visible when the swing-out door is opened. A build-up of grinds on this disc can affect the performance of the machine. Wipe the disc clean then dry thoroughly.

CAUTION

The coffee basket, gold tone or paper ﬁlter may still be very hot after brewing. Use caution and allow to cool before removing.

NOTE

If using the gold tone ﬁlter, you may notice the brewing cycle ﬁnish before the ready signal sounds. This is normal. The total brewing time displayed on the LCD screen is calculated using paper ﬁlters as coffee passes through paper ﬁlters slower.

PROGRAMMING THE CLOCK (OPTIONAL)

1. Press the MENU|EXIT button.

2. Press the STRENGTH dial. The LCD

screen displays the current time, ﬂashing.

3. Rotate the STRENGTH dial to adjust

the time.

4. Press the STRENGTH button to set.

The machine will beep to conﬁrm.

5. The LCD will return to the main screen

when the clock is set.

PROGRAMMING AUTO START (OPTIONAL)

The Auto Start feature allows you to program the speciﬁc time when the coffee machine will automatically turn on and start the grinding and brewing cycle.

You must set the clock to use the Auto Start feature. Always remember to reset the clock for time changes, power outages and when you unplug the machine.

1. Press the AUTO START button.

The current Auto Start time will be displayed and ﬂashing.

OPERATING YOUR BREVILLE PRODUCT OPERATING YOUR BREVILLE PRODUCTOPERATING YOUR BREVILLE PRODUCTOPERATING YOUR BREVILLE PRODUCT

2. Rotate the STRENGTH dial to adjust

the time you want the brewer to start.

3. Press the STRENGTH button to set the

Auto Start time. The machine will beep to conﬁrm.

NOTE

If you have not set the clock time, please follow the instructions below.

4. The current clock time will ﬂash on the

LCD. Rotate the STRENGTH button to set the current clock time. Press the STRENGTH button to conﬁrm.

5. The machine will now automatically

start the brew cycle at the time you’ve set.

6. Make sure you have:

• Enough water in the tank.

• Selected the number of cups you wish

to brew.

• Set the strength.

• Fill hopper with fresh beans.

• A fresh ﬁlter paper in the brew basket

& the drawer is closed.

• A clean, empty carafe under the brew

baske t.

7. If ‘AUTO START ON’ does not appear,

then the Auto Start feature has not be activated.

8. To cancel the Auto On after it’s been

set, press the AUTO START button once.

NOTE

The Auto Start feature must be selected each time you want to pre-schedule a brew. Press the AUTO START button and the programmed Auto Start time will display on the LCD screen.

NOTE

Always remember to reset the clock and Auto Start time when there is a time change, power outage or after you unplug the machine.

CHANGING THE ‘READY’ SIGNAL VOLUME

The volume of the ‘Ready’ signal can be changed to suit your preference. There are 3 options:

1. Press the MENU|EXIT button.

2. Rotate the STRENGTH dial to SOUND.

3. Press the STRENGTH dial to select

SOUND.

4. SOUND and the current setting will be

displayed, ﬂashing.

5. Rotate the STRENGTH to select your

setting.

6. Press the STRENGTH dial to conﬁrm.

The machine will beep to conﬁrm.

7. LCD will return to the main screen.

18 19

+ 23 hidden pages