Breville is a registered trademark of Breville Pty. Ltd. A.B.N. 98 000 092 928.
Due to continued product improvement, the products illustrated/photographed
in this booklet may vary slightly from the actual product.
Copyright Breville Pty. Ltd. 2012.
Canada
Mail: Breville Canada
2555, Avenue de l’Aviation
Pointe-Claire (Montreal)
Quebec H9P 2Z2
1-855-683-3535
Phone:
Email:
askus@breville.ca
Model BDC600XL /A Issue - D12
BDC600XL /A
CONGRATULATIONS
CONTENTS
4
Breville recommends safety fi rst
8Know your Breville product
on the purchase of your Breville product
Register online for product support
and exclusive offers.
USA Consumers: www.brevilleusa.com
Canadian Consumers: www.breville.ca
*
12Operating your Breville product
13 Before fi rst use
14 Using the YouBrew® - Carafe Mode
17 Using the YouBrew® - Single Cup Mode
20 Programming the Clock (Optional)
20 Programming Auto-Start (Optional)
21 Changing the ‘Ready’ Signal Volume
22 Helpful Tips
24 Care & cleaning
28 Troubleshooting
36 French
*Registering is not a substitute for proof of purchase when submitting a Warranty Claim.
3
BREVILLE RECOMMENDS SAFETY FIRSTBREVILLE RECOMMENDS SAFETY FIRST
At Breville we are very safety conscious. We design and manufacture consumer products with
the safety of you, our valued customer, foremost in mind. In addition we ask that you exercise
a degree of care when using any electrical appliance and adhere to the following precautions.
IMPORTANT SAFEGUARDS
READ ALL INSTRUCTIONS
• Carefully read all instructions before
operating the appliance for the fi rst time
and save for future reference.
• Remove and safely discard any
packaging materials and promotional
labels before using the appliance for the
fi rst time.
• To eliminate a choking hazard for young
children, remove and safely discard the
protective cover fi tted to the power plug
of this appliance.
• Do not place the appliance near the edge
of a bench or table during operation.
Ensure that the surface is level, clean
and free of water.
• Always operate the appliance on a stable
and heat resistant surface. Do not use on
a cloth-covered surface, near curtains or
other fl ammable materials.
• Do not place the appliance on or near a
hot gas burner, electric element or where
it could touch a heated oven.
• Do not operate the appliance on metal
surfaces, for example, a sink drain board.
• Position the appliance with a minimum
distance of 4” (10cm) of space on both
sides of the appliance. This will allow for
adequate air circulation.
• Always ensure the appliance is properly
assembled before connecting to a
power outlet and operating. Follow the
instructions described in this book.
• Do not operate the appliance without
water in the water tank. Use only cold,
preferably fi ltered water. Do not use any
other liquid.
• Ensure the supplied gold tone fi lter or
a paper fi lter (8-12 cup, fl at base basket
style with ~ 3¼"/8.25cm base) is placed
in the coffee basket before using the
appliance. Do not use the gold tone fi lter
in conjunction with a paper fi lter.
• Never open the swing-out door
and remove the coffee basket while
brewing. Hot water and coffee can
cause injury. Allow to drain before
removing to avoid scalding.
• The carafe is designed for use with this
appliance only. It must never be used on
a range top or in a microwave.
• Always ensure the carafe is completely
empty of any contents before brewing.
• Always ensure the carafe lid is
securely locked in place onto the carafe
then placed under the drip stop outlet
before brewing.
• Scalding may occur if the carafe lid is
removed during the brewing cycle.
• Always ensure the carafe lid is
securely locked in place onto the
carafe before pouring.
• Do not use the carafe with a cracked,
loose, weakened or damaged handle.
• Do not touch hot surfaces. Use the
handle for lifting and carrying the carafe.
• Do not set a hot carafe on a wet, cold or
heat sensitive surface.
• Do not operate the grinder without
the bean hopper lid in position. Keep
fi ngers, hands, hair, clothing and
utensils away from the bean hopper
during operation. Avoid contact with
moving parts.
• Check the grinder for presence of
foreign objects before using.
• Use the grinder to grind roasted coffee
beans only. Grinding other substances,
such as nuts, spices or unroasted beans
may dull the burr and cause poor
grinding or injury.
• Always switch the appliance off by
pressing the POWER button off. Remove
the power plug from the power outlet
before attempting to move the appliance,
when the appliance is not in use and
before cleaning and storing. Allow to cool
before putting on or taking off parts, and
before cleaning the appliance.
• Keep the appliance and accessories clean.
Strictly follow the care and cleaning
instructions described in this book.
• Do not use cleaners, steel wool pads or
other abrasive materials when cleaning
any part of this appliance.
• This appliance is not intended to be
operated by means of an external timer
or separate remote control system.
• The use of attachments not sold or
recommended by Breville may cause fi re,
electric shock or injuries.
IMPORTANT SAFEGUARDS FOR
ALL ELECTRICAL APPLIANCES
• Fully unwind cord before use.
• To protect against electric shock, do not
immerse cord, plug or appliance in water
or any other liquid.
• Do not let the cord hang over the edge
of a bench or table, touch hot surfaces, or
become knotted.
• Do not leave the appliance unattended
when in use.
• This appliance is not intended for use
by persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience or
knowledge, unless they have been given
supervision or instruction concerning
use of the appliance by a person
responsible for their safety.
• Children should be supervised to ensure
they do not play with the appliance.
• This appliance is recommended for
household use only. Do not use this
appliance for anything other than its
intended use. Do not use in moving
vehicles or boats. Do not use outdoors.
• It is recommended to regularly inspect
the appliance. Do not use the appliance
if the power supply cord, power plug, or
appliance becomes damaged in anyway.
Immediately cease use and call Breville
Consumer Service.
• For any maintenance other than
cleaning call Breville Consumer
Service.
• This appliance is equipped with a
power cord having a grounding wire
with a grounding plug. The appliance
must be grounded using a 3-hole
properly grounded outlet. In the event
of an electrical short circuit, grounding
reduces the risk of electrical shock.
• If the appliance is of the grounded
type, the extension cord should be a
grounding 3-wire cord. If the power
outlet is a standard 2-prong wall outlet,
it is your personal responsibility and
obligation to have it replaced with a
properly grounded 3-prong wall outlet.
• Do not, under any circumstances, cut or
remove the third (ground) prong from
the power cord or use an adapter.
• Consult a qualifi ed electrician if
the grounding instructions are not
completely understood, or if doubt
exists as to whether the appliance is
properly grounded.
CAUTION
We recommend using cold, fi ltered
water. We do not recommend the use of
de-mineralized or distilled water as this
may affect the taste of brewed coffee
and how the coffee machine is designed
to function.
45
5
BREVILLE RECOMMENDS SAFETY FIRST
SHORT CORD INSTRUCTIONS
Your Breville appliance is fi tted with a short
power supply cord as a safety precaution to
prevent personal injury or property damage
resulting from pulling, tripping or becoming
entangled with a longer cord. Do not allow
children to use or be near this appliance
without close adult supervision. Longer
detachable power supply cords or extension
cords are available and may be used if care
is exercised. If an extension cord is used,
(1) the marked electrical rating of the cord
set or extension cord should be at least
as great as the electrical rating of the
appliance, (2) the cord should be arranged
so that it will not drape over the countertop
or tabletop where it can be pulled on by
children or tripped over unintentionally
and (3) the extension cord must include a
3-prong grounding plug.
BREVILLE ASSIST™ PLUG
Your Breville appliance comes with a unique
Assist™ Plug, conveniently designed with
a fi nger hole in the power plug for easy
and safe removal from the wall outlet. For
safety reasons it is recommended you
plug your Breville appliance directly into
its own electrical outlet on a dedicated
circuit separate from other appliances. If
the electric circuit is overloaded with other
appliances, your appliance may not function
properly. Use in conjunction with a power
strip or extension cord is not recommended.
CALIFORNIA PROPOSITION 65:
(Applicable to California residents only).
This product contains chemicals known to
the State of California to cause cancer, birth
defects or other reproductive harm.
FOR HOUSEHOLD USE ONLY
SAVE THESE INSTRUCTIONS
6
KNOW
KNOW YOUR BREVILLE PRODUCT
Pick how you want your coffee.
The YouBrew’s intelligent features take care of the rest.
your Breville product
You pick your
beans & roast…
You pick your
brew strength…
You pick your
flavor profile…
You pick a single
cup, travel mug
or carafe…
The YouBrew’s integrated burr grinder grinds your choice of beans
just prior to brewing for maximum freshness, flavor and aroma.
The grind is preset to the optimal size and can be turned off when
using pre-ground coffee.
The YouBrew’s 7 strength settings vary the amount of freshly
ground coffee for a 'MILD', 'STRONG' or 'INTENSE' brew. The
stronger the strength setting selected, the more coffee is ground.
There is no need to calculate how much coffee you need for the
amount of water in the tank. Simply select the desired strength
and the Brew IQ
amount of coffee to ensure a consistent strength regardless of
whether you choose a single cup, travel mug or whole carafe.
The YouBrew’s 5 flavor settings vary the steeping time of the
coffee and water. The 'LITE' setting steeps for less time to
produce a light-flavored cup. The 'BOLD' setting steeps for more
time for a bolder, more full-flavored coffee.
The YouBrew gives you the flexibility to brew directly into a cup,
travel mug or carafe. Set the optional Auto-Start feature and have
a travel mug ready to go in the morning. Brew a single cup for one
person at night. Alternatively, brew a whole carafe for weekend
entertaining. The Brew IQ
dose to ensure the temperature and strength of your brew is
consistent regardless of whether you choose a single cup, travel
mug or whole carafe.
®
System will intelligently dose the correct
®
System will intelligently pre-heat and
89
KNOW YOUR BREVILLE PRODUCTKNOW YOUR BREVILLE PRODUCT
All parts of the
YouBrew® that
come into contact
with coffee and
water are BPA Free.
1
2
3
4
5
6
7
8
10
9
11
1. Bean Hopper Lid
2. 0.5lb Bean Hopper
3. Bean Hopper Locking System seals the
base of the bean hopper for easy removal,
storage and transfer of coffee beans.
4. Cleaning Brush for convenient
cleaning of the grinding burrs and
coffee grinds chute.
5. Integrated Burr Grinder grinds
whole beans just prior to brewing for
maximum freshness, fl avor and aroma.
Grinder can be turned off when using
pre-ground coffee.
6. 12-Cup (60oz) Water Tank with
fl ip-top lid for convenient, front-access
fi lling. Grille prevents large debris from
entering the tank while the ‘MAX’ level
fl oat rises when the tank is full.
7. Contoured Control Panel with angled
design for easy viewing of the backlit
LCD screen.
8. Coffee Grinds Chute delivers ground
coffee from the bean hopper to the
coffee basket.
12
13
14
15
16
17
9. Removable Grinds Catcher catches loose
grinds from the coffee grinds chute.
10. Carafe Lid.
11. 12-Cup Double-Wall, Stainless Steel
Thermal Carafe
12. Removable Gold Tone Filter
13. Soft Opening, Swing-Out Door with
safety interlock system prevents
operation if the coffee basket is not
correctly assembled or the door is not
properly closed.
14. Removable Coffee Basket lifts out for
easy fi lling and cleaning. Holds the
included gold tone fi lter or paper fi lters.
15. Steam Baffl e assists with water overfl ow
if the coffee basket becomes blocked.
16. Brew Pause Drip Stop temporarily
ceases the fl ow of coffee when the
carafe is removed so a cup can be
poured mid-brew.
17. Drip Tray can be removed for direct
brewing into tall cups & travel mugs.
1826
1920 21 22232425
18. OPEN button
• Press to open the swing-out door.
19. SINGLE CUP button
• Press to brew a single cup of coffee.
• Continue pressing to select between
9 brew sizes.
20. CARAFE button
• Press to brew a carafe of coffee.
• Continue pressing to select a specifi c
carafe size between 2 cups (minimum)
and 12 cups (maximum).
21. button
• Use in conjunction with the
STRENGTH | FLAVOR button to
increase the volume of the ‘Ready’
signal.
• Use in conjunction with the
STRENGTH | FLAVOR button to
increase the brew strength and fl avor.
• Use in conjunction with the
PROGRAM button to program the
clock and Auto-Start.
22. button
• Use in conjunction with the
STRENGTH | FLAVOR button to
decrease the volume of the ‘Ready’ signal.
• Use in conjunction with the
STRENGTH | FLAVOR button to
decrease the brew strength and fl avor.
• Use in conjunction with the
PROGRAM button to program the
clock and Auto-Start.
23. STRENGTH | FLAVOR button
• Press to adjust the brew strength.
7 settings plus ‘PRE-GROUND’ coffee
setting vary the amount of freshly ground
coffee for a mild, strong or intense brew.
• Press to adjust the fl avor.
5 settings vary the steeping time of
the coffee and water to produce a
light-fl avored cup or a bolder, more
full-fl avored coffee.
24. PROGRAM | SET CLOCK button
• Press to program the clock
(‘TIME NOW’ time).
• Press to program the Auto-Start
(‘START AT’ time).
25. START | CANCEL button
• Press to start or cancel the brew cycle.
26. POWER button
• Press to turn the power on or off, or to
exit out of POWER SAVE mode.
1011
BEFORE FIRST USE
OPERATING
your Breville product
BEFORE FIRST USE
• Before using the YouBrew® for the fi rst
time, ensure you have unpacked all
parts and accessories before removing
and safely discarding all packaging
material and promotional labels. Ensure
the power cord is unplugged from the
power outlet.
• Wipe the exterior stainless steel
housing with a soft, damp cloth. Wash
the bean hopper and lid, coffee basket,
gold tone fi lter and carafe in warm,
soapy water and a soft cloth. Do not
use abrasive cleansers, pads or cloths
which can scratch the surface. Rinse
and dry thoroughly.
INITIAL SET UP
1. Install the Bean Hopper
Position the hopper onto the machine.
Turn the locking knob clockwise in the
direction of the LOCK arrow until it
clicks. Fill the hopper with fresh beans.
We recommend always keeping the hopper
full (0.5lb maximum) to ensure there are
suffi cient beans. However, never over-pack
the hopper as this may result in the grinder
jamming. Replace the hopper lid.
NOTE
The coffee machine will enter POWER
SAVE mode after remaining idle for
10 minutes. Press the POWER button
to exit POWER SAVE mode and
re-start the machine.
3. Install the Coffee Basket
For best results, we recommend pre-heating
the coffee basket by running it under
hot tap water. Ensure to dry the coffee
basket thoroughly, taking particular care
to completely dry the chute area. Line the
coffee basket with either the provided gold
tone fi lter or a paper fi lter. Never use both
at the same time.
a) Provided gold tone fi lter. When using
the gold tone fi lter, be sure that the
handle is positioned towards the hinge
area of the coffee basket. If you do not,
the handle may interfere with the fl ow of
ground coffee into the gold tone fi lter.
HANDLE TOWARDS
COFFEE BASKET HINGE
ENSURE CHUTE
AREA IS
COMPLETELY DRY
NOTE
For easy removal, storage and
transfer of beans, the hopper can be
removed by turning the locking knob
counter-clockwise in the direction
of the UNLOCK arrow. If you have
removed the hopper, ensure it is
securely reassembled back onto
the machine. The safety interlock
system will prevent operation if the
hopper is incorrectly assembled. The
LCD screen will fl ash ‘LOCK BEAN
HOPPER’ until the issue is resolved.
2. Plug in the Power Cord
Unwind the power cord completely and
insert the power plug into a grounded
110-120V power outlet. Press the POWER
button. The LCD screen will illuminate.
NOTE
The gold tone fi lter will allow some
fi ne coffee grounds to fall into the
coffee. This will appear as sediment in
the cup or carafe. This is normal.
Only use the gold tone fi lter provided
as others may cause the machine to
overfl ow.
13
USING THE YOUBREW® - CARAFE MODEUSING THE YOUBREW® - CARAFE MODE
CLICK
b) Paper fi lter (8-12 cup, fl at base basket
style with ~ 3¼"/8.25cm base). Ensure
that the paper fi lter is completely open
and touching the side walls and bottom
of the coffee basket.
Close the coffee basket lid. Press the
OPEN button to open the swing-out door.
Attach the coffee basket to the swing-out
door by ensuring the hinge area of the
coffee basket is fi rmly seated in its most
downward position on the two door hooks.
Close the door until it clicks shut.
NOTE
The safety interlock system will
prevent operation if the coffee basket
is not in place, if it is not fi rmly seated
on the two door hooks, or if the
swing-out door is not closed. The LCD
screen will fl ash ‘EMPTY COFFEE
FILTER’ until the issues are resolved.
USING THE YOUBREW®
- CARAFE MODE
First Time Use Only
We recommend fl ushing the machine
to remove any dust particles or residues
from the manufacturing process. Follow
the proceeding instructions, ensuring to
completely fi ll the water tank (Step 1), select
‘12 CUPS’ (Step 3) and the ‘PRE-GROUND’
coffee setting (Step 4). However do not add any coffee to the coffee basket. Once the
cycle is complete, discard the water from the
carafe and repeat the cycle again for best
results. The machine is now ready to use.
CAUTION
We recommend using cold, fi ltered
water. We do not recommend the use of
de-mineralized or distilled water as this
may affect the taste of brewed coffee
and how the coffee machine is designed
to function.
1. Fill the Water Tank
Press open the fl ip-top lid. Pour the desired
amount of cold, preferably fi ltered water into
the tank using a jug or the provided carafe.
If using the carafe, ensure the carafe lid is
securely locked in place. The LCD screen
will indicate the amount of water in the tank
as it is fi lled. The machine will beep when
full and the water level fl oat will rise to
indicate the maximum level. Do not exceed
the 12 cup maximum. Doing so may cause
the carafe to overfl ow or water spillage at the
back of the machine. Close the fl ip-top lid.
NOTE
Check the water level on the LCD
screen before use. We recommend
always keeping the water tank full.
The water tank should be refi lled with
cold, preferably fi ltered water. Do not
fi ll with any other liquid.
NOTE
Never pour water into the bean
hopper or grinding chamber area.
Doing so can cause the grinder to
clog. Only re-commence use when
the grinding chamber and grinding
burrs are completely dry. Refer to
Troubleshooting, ‘Moisture clogging
grinder’, page 29.
NOTE
Never fi ll the water tank once the
coffee machine has started a brewing
cycle. This will affect the volume
dispensed into the carafe.
2. Pre-Warm the Carafe
A warm carafe will help maintain the coffee’s
optimal temperature and keep coffee hotter
for longer. Remove the carafe lid by turning
counter-clockwise then lifting upwards.
Fill the carafe with hot water for about
30 seconds then discard the water. To lock
the carafe lid back into position, align the
arrow on the carafe lid with the ALIGN
arrow on the carafe. Turn clockwise until the
arrow on the carafe lid aligns with the LOCK
arrow on the carafe. This ensures that the
lid is closed and in the proper position for
brewing and pouring. Place the carafe into
position under the drip stop outlet.
ALIGN
ARROWS
THEN TURN TO LOCK
NOTE
Ensure the carafe is completely empty
and the lid is securely locked in place
before placing under the drip stop
outlet. Starting a brew cycle with
water or coffee in the carafe will cause
the carafe to over fl ow.
3. Select ‘Carafe’ Mode
Press the CARAFE button. The LCD screen
will display a carafe symbol and the current
number of cups selected. Continue pressing
the CARAFE button to select the desired
number of cups. You can choose less than
the current tank level (2 cup minimum),
while the maximum is the amount of water
in the tank, up to 12 cups. Each cup is
approximately 5 fl .oz.
4. Select the Brew Strength or
‘PRE-GROUND’ Coffee Setting
Press the STRENGTH button. The LCD
screen will fl ash the current strength setting
and the
and fl ash. Use these buttons to cycle through
7 strength settings from ‘MILD’, ‘STRONG’
to ‘INTENSE’ or for the ‘PRE-GROUND’
coffee setting. When the ‘INTENSE’ strength
setting is selected, the maximum number
of cups that can be brewed is 9 cups. This
ensures the maximum coffee to water ratio.
Press the STRENGTH button to select. The
LCD screen will cease to fl ash once selected.
NOTE
If using pre-ground coffee, select the
‘PRE-GROUND’ coffee setting. This
will disable the burr grinder. Add preground coffee to the gold tone fi lter
or a paper fi lter (8-12 cup, fl at base
basket style with ~ 3¼"/8.25cm base).
We recommend 1 level tablespoon of
pre-ground coffee per 5oz/150ml cup
of water. Adjust the amount according
to your individual taste. The maximum
capacity for pre-ground coffee is
16 level tablespoons. Exceeding this
amount may cause overfl ow.
When using the machine for the fi rst
time, we recommend selecting the
‘PRE-GROUND’ coffee setting, however
omitting the addition of pre-ground
coffee. This will fl ush the machine and
remove any dust particles or residues
from the manufacturing process.
and buttons will illuminate
1415
USING THE YOUBREW® - SINGLE CUP MODEUSING THE YOUBREW® - CARAFE MODE
5. Start the Brew Cycle
Press the START | CANCEL button. The
grinder will commence grinding the
correct amount of coffee for the selected
brew size and strength. If the
‘PRE-GROUND’ coffee setting has been
selected, the grinder will be disabled.
NOTE
Steam may emit from the rear steam
vent during grinding and brewing.
This is normal.
The count-down timer will then begin. The
time displayed is an estimate only and will
depend on the amount and strength settings
you have selected.
The LCD screen will display:
a) ‘PRE-HEATING’ as the water is heated
to the optimal temperature. The
pre-heating time will depend on the
starting temperature of the water in
the water tank.
b) ‘BREWING’ as the coffee is dispensed
into the carafe.
To stop the cycle at any time, press the
START | CANCEL button. You will hear
a winding noise. This is normal.
CAUTION
Never open the swing-out door and
remove the coffee basket while brewing.
Hot water and coffee can cause injury.
6. Using the Brew Pause Feature
The Brew Pause feature temporarily
ceases the fl ow of coffee when the carafe is
removed so a cup can be poured mid-brew.
Do not remove the carafe for longer than
20 seconds or the coffee may overfl ow the
coffee basket.
1617
7. Empty the Coffee Basket
Once the brewing cycle is complete, the
ready signal will sound and a winding noise
will be heard. This is normal. The coffee
machine will automatically shut-off, however
the LCD screen will fl ash ‘EMPTY COFFEE
FILTER’ as a reminder to remove the coffee
basket and discard the used grinds. Wash
the coffee basket, taking particular care to
rinse the chute area. Then dry the coffee
basket and chute area thoroughly.
We also recommend checking the coffee
grinds chute disc for any build-up of coffee
grinds. This is the stainless steel disc that is
visible when the swing-out door is opened.
A build-up of grinds on this disc can affect
the performance of the machine. Wipe the
disc clean then dry thoroughly.
CAUTION
The coffee basket and gold tone or
paper fi lter may still be very hot after
brewing. Use caution and allow to cool
before removing.
8. Pour and Enjoy
Ensure the carafe lid is securely locked in
position. There is no need to turn or adjust
the lid before pouring. The lid automatically
opens when pouring and closes when not to
keep coffee hot.
CAUTION
Hot steam may rise when pouring.
The bottom of the carafe is hot to touch
for several minutes after brewing. Use
caution and ensure not to set the carafe
on a heat sensitive surface.
USING THE YOUBREW®
- SINGLE CUP MODE
First Time Use Only
We recommend fl ushing the machine to
remove any dust particles or residues from
the manufacturing process. Follow the
instructions, ‘Using the YouBrew
Mode’, ensuring to completely fi ll the water
tank (Step 1), select ‘12 CUPS’ (Step 3)
and the ‘PRE-GROUND’ coffee setting
(Step 4). However do not add any coffee to the coffee basket. Once the cycle is
complete, discard the water from the carafe
and repeat the cycle again for best results.
The machine is now ready to use.
®
- Carafe
CAUTION
We recommend using cold, fi ltered
water. We do not recommend the use of
de-mineralized or distilled water as this
may affect the taste of brewed coffee
and how the coffee machine is designed
to function.
1. Fill the Water Tank
Press open the fl ip-top lid. Pour the desired
amount of cold, preferably fi ltered water into
the tank using a jug or the provided carafe.
If using the carafe, ensure the carafe lid is
securely locked in place. The LCD screen
will indicate the amount of water in the tank
as it is fi lled. The machine will beep when
full and the water level fl oat will rise to
indicate the maximum level. Do not exceed
the 12 cup maximum. Doing so may cause
water spillage at the back of the machine.
Close the fl ip-top lid.
NOTE
Check the water level on the LCD
screen before use. We recommend
always keeping the water tank full.
The water tank should be refi lled with
cold, preferably fi ltered water. Do not
fi ll with any other liquid.
NOTE
Never pour water into the bean
hopper or grinding chamber area.
Doing so can cause the grinder to
clog. Only re-commence use when
the grinding chamber and grinding
burrs are completely dry. Refer to
Troubleshooting, ‘Moisture clogging
grinder’, page 29.
NOTE
Never fi ll the water tank once the
coffee machine has started a brewing
cycle. This will affect the volume
dispensed into the cup.
2. Pre-Warm the Cup or Travel Mug
A warm cup will help maintain the coffee’s
optimal temperature and keep coffee hotter
for longer. Fill the cup with hot water for about
30 seconds then discard the water. Place the
cup into position under the drip stop outlet.
TIP
For taller cups and travel mugs,
remove the drip tray at the base of
the machine. Press the OPEN button
to open the swing-out door. Insert
the cup/mug into the drip tray cavity
before closing the swing-out door. The
maximum cup/mug dimensions are
7.5" height, 2¾" diameter.
REMOVE DRIP TRAY, OPEN DOOR,
INSERT CUP, CLOSE DOOR.
USING THE YOUBREW® - SINGLE CUP MODEUSING THE YOUBREW® - SINGLE CUP MODE
3. Select ‘Single Cup’ Mode
Press the SINGLE CUP button. The LCD
screen will display a cup symbol and the
current cup size selected. Continue pressing
the SINGLE CUP button to select the
desired size.
There are 9 size options to accommodate
for different amounts or milk, half-andhalf and creamer. Below is a guide to the
amount brewed at each setting. Always
ensure your cup is an adequate size for the
setting selected.
SETTING AMOUNT BREWED
1~ 7.5oz
2~ 9.5oz
3~ 11oz
4~ 12.5oz
5~ 14.5oz
6~ 16oz
7~ 17.5oz
8~ 19.5oz
9~ 21oz
The amounts above are approximate only.
Actual amounts may vary due to the type of
fi lter used, the coffee bean size, roast, blend
and freshness, or amount and type of
pre-ground coffee used.
4. Select the Brew Strength or
‘PRE-GROUND’ Coffee Setting
Press the STRENGTH | FLAVOR button.
The LCD screen will fl ash the current
strength setting and the
and buttons
will illuminate and fl ash. Use these buttons
to cycle through 7 strength settings from
‘MILD’, ‘STRONG’ to ‘INTENSE’ or for the
‘PRE-GROUND’ coffee setting.
Press the STRENGTH | FLAVOR button to
select. The LCD screen will fl ash the current
fl avor setting.
NOTE
If using pre-ground coffee, select the
‘PRE-GROUND’ coffee setting. This
will disable the burr grinder. Add
pre-ground coffee to the gold tone
fi lter or a paper fi lter (8-12 cup, fl at
base basket style with ~ 3¼"/8.25cm
base). We recommend 1 level
tablespoon of pre-ground coffee per
5oz/150ml cup of water. Adjust the
amount according to your individual
taste. The maximum capacity for
pre-ground coffee is 16 level
tablespoons. Exceeding this amount
may cause overfl ow.
5. Select the Flavor Setting
Press the STRENGTH | FLAVOR button
until the LCD screen fl ashes the current
fl avor setting and the
and buttons
illuminate and fl ash. Use these buttons to
cycle through 5 fl avor settings from ‘LITE’
to ‘BOLD’. These settings vary the steeping
time of the coffee and water. The ‘LITE’
setting steeps for less time to produce
a light-fl avored cup. The ‘BOLD’ setting
steeps for more time for a bolder, more
full-fl avored coffee.
Press the STRENGTH | FLAVOR button
to select. The LCD screen will cease to
fl ash once selected.
6. Start the Brew Cycle
Press the START | CANCEL button.
The grinder will commence grinding
the correct amount of coffee for the
selected brew size and strength. If the
‘PRE-GROUND’ coffee setting has been
selected, the grinder will be disabled.
NOTE
Steam may emit from the rear steam
vent during grinding and brewing.
This is normal.
The count-down timer will then begin. The
time displayed is an estimate only and will
depend on the amount, strength and fl avor
settings you have selected. The LCD screen
will display:
a) ‘PRE-HEATING’ as the water is heated
to the optimal temperature. The
pre-heating time will depend on the
starting temperature of the water in
the water tank.
b) ‘STEEPING’ as coffee and water are
steeped together.
c) ‘BREWING’ as the coffee is dispensed
into the cup.
To stop the cycle at any time, press the
START | CANCEL button. You will hear
a winding noise. This is normal.
CAUTION
Never open the swing-out door
and remove the coffee basket while
brewing. Hot water and coffee can
cause injury.
7. Empty the Coffee Basket
Once the brewing cycle is complete, the
ready signal will sound and a winding noise
will be heard. This is normal. The coffee
machine will automatically shut-off, however
the LCD screen will fl ash ‘EMPTY COFFEE
FILTER’ as a reminder to remove the coffee
basket and discard the used grinds. Wash
the coffee basket, taking particular care to
rinse the chute area. Then dry the coffee
basket and chute area thoroughly.
We also recommend checking the coffee
grinds chute disc for any build-up of coffee
grinds. This is the stainless steel disc that is
visible when the swing-out door is opened.
A build-up of grinds on this disc can affect
the performance of the machine. Wipe the
disc clean then dry thoroughly.
CAUTION
The coffee basket, gold tone or paper
fi lter may still be very hot after
brewing. Use caution and allow to
cool before removing.
NOTE
If using the gold tone fi lter, you
may notice the brewing cycle fi nish
before the ready signal sounds.
This is normal. The total brewing
time displayed on the LCD screen is
calculated using paper fi lters as coffee
passes through paper fi lters slower.
1819
CHANGING THE ‘READY’ SIGNAL VOLUMEPROGRAMMING THE CLOCK / AUTO-START (OPTIONAL)
PROGRAMMING THE CLOCK
(OPTIONAL)
You must set the clock to use the Auto-Start
feature. Always remember to reset the clock
for time changes, power outages and when
you unplug the machine.
1. Press the PROGRAM button until the
LCD screen displays ‘TIME NOW’.
Once this appears, press and hold the
PROGRAM button until the PROGRAM
button illuminates red and the LCD
screen displays a fl ashing ‘AM’.
2. Use the and buttons to select
either AM or PM.
3. Press the PROGRAM button. The
LCD screen will display a fl ashing
hour.
4. Use the and buttons to select
the desired hour.
5. Press the PROGRAM button. The
LCD screen will display a fl ashing
minute.
6. Use the and buttons to select
the desired minute.
TIP
For faster scrolling, press and hold the
and buttons.
Press the PROGRAM button to
7.
fi nish. The LCD screen will display
‘TIME NOW’ and the programmed time.
PROGRAM
SET CLOCK
PROGRAMMING AUTO-START
(OPTIONAL)
The Auto-Start feature allows you to
program the specifi c time when the coffee
machine will automatically turn on and start
the preheating and grinding cycle.
1. Ensure the clock is set.
2. Press the PROGRAM button until
the LCD screen displays ‘START AT’.
Once this appears, press and hold
the PROGRAM button until the
LCD screen displays a fl ashing
‘AM’ or 'PM'.
3. Use the and buttons to select
either AM or PM.
4. Press the PROGRAM button.
The LCD screen will display a
fl ashing hour.
5. Use the and buttons to select
the desired hour.
6. Press the PROGRAM button.
The LCD screen will display a
fl ashing minute.
7. Use the and buttons to select
the desired minute.
TIP
For faster scrolling, press and hold the
and buttons.
Press the PROGRAM button. It
8.
will illuminate red and the LCD
screen will display the programmed
‘START AT’ time for 5 seconds.
During this time, press the
START | CANCEL button. The
LCD screen will dim and display
‘PROGRAM ON’ to indicate
that the Auto-Start feature has
been successfully turned on. If
‘PROGRAM ON’ does not appear,
then the Auto-Start feature has not
been activated.
NOTE
During Step 8, the programmed
'START AT' time will appear on the
LCD screen for 5 seconds. If the
START | CANCEL button is not
pressed within 5 seconds, 'TIME
NOW' will appear on the LCD screen
and pressing the START | CANCEL
button will cause the coffee machine
to start grinding and brewing.
START
CANCEL
9. Ensure that the coffee machine
is correctly assembled and
prepared with:
• Suffi cient water in the water tank and
coffee beans in the bean hopper.
• The coffee basket assembled with
an empty gold tone fi lter or paper
fi lter (8-12 cup, fl at base basket style
with ~ 3¼"/8.25cm base).
• Either a cup, travel mug or carafe
positioned under the drip stop outlet.
NOTE
To cancel a programmed Auto-Start,
press the START | CANCEL button
until the LCD screen no longer
displays ‘PROGRAM ON’.
NOTE
The Auto-Start feature must be
selected each time you want to
pre-schedule a brew. Press the
PROGRAM button until the LCD
screen displays ‘START AT’. The
coffee machine will remember the
last programmed Auto-Start time, so
simply press the START | CANCEL
button to re-select. Ensure
‘PROGRAM ON’ is displayed on the
LCD screen.
NOTE
Always remember to reset the clock
and Auto-Start time when there is a
time change, power outage or after
you unplug the machine.
CHANGING THE ‘READY’
SIGNAL VOLUME
The volume of the ‘Ready’ signal can
be changed to suit your preference.
There are 3 options:
HIGH
LOW
MUTE
Press and hold the STRENGTH | FLAVOR
button until the LCD screen fl ashes one of
the sound icons pictured above. While the
icon fl ashes, use the
select the desired volume. The volume is
selected once the icon stops fl ashing.
The selected volume will remain displayed
on the LCD screen.
or button to
2021
Loading...
+ 25 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.