Bosch FMC‑300RW Datasheet

Fire Alarm Systems - FMC‑300RW Single Action Call Points

FMC‑300RW Single Action Call Points

u Alarm triggering by pressing the black marking

or breaking the glass pane

u Protection against injury through foil-labeled

glass pane

u LED display for triggered alarm or inspection

evaluation

FMC‑300RW Single Action Call Points are used for manual alarm triggering and are employed in conventional technology.

Functions

Single action call points with glass pane:

Pressing the black marking (1) breaks the glass pane (3), which triggers the alarm and causes the LED display (2) to flash. Single action call points can be reset with the test key and by replacing the glass pane (3). The LED display (2) switches off.

Resettable single action call points:

Pressing the black marking (1) triggers the alarm. The alarm status is displayed by the red window color (4) and the flashing LED display (2). Single action call points can be reset using the test key. The LED display (2) switches off. The standby mode is indicated by the white window color (4).

Certifications and approvals

Applies to EN54‑11:2001/A1:2005

Region Regulatory compliance/quality marks

Germany

Europe

VdS

CPD

G 207086 FMC-300RW

FMC-300RW-GSGRD, -GSRRD

FMC-300RW-GSGYE/BU, -GSRYE/BU

0786-CPD-20332 FMC-300RW

Installation/configuration notes

• Manual call points have to be mounted visibly along escape and rescue routes (e.g. exits, passageways, stairwells) and be easily accessible.

• An installation height of 1400mm ±200mm, measured from the middle of the manual call point to the floor, must be maintained.

• Manual call points must be illuminated sufficiently with daylight or another light source (including emergency lighting, if present).

• Max. one test detector may be used for primary lines together with automatic detectors. The test detector is connected at the end of the primary line.

• Further standards, guidelines and planning recommendations regarding the installation location etc., should also be taken into consideration.

• Regulations of local fire departments must be observed.

Fire Alarm Systems - FMC‑300RW Single Action Call Points

2 | 3

Technical specifications

Electrical

Operating voltage

Current consumption

Alarm resistor

20VDC

(8.5VDC to 30VDC)

specified by the respective security system

820Ω +/- 10%

(8.5VDC to 30VDC)

Mechanical components

Dimensions (H x W x D)

Housing material

Colors

• Red

• Blue

• Yellow

87mm x 87mm x 56mm (3.4 in. x

3.4 in. x 2.2 in.)

Plastic, ASA

RAL 3001

RAL 5005

RAL 1003

Environmental conditions

Protection category according to EN 60529

Permissible operating temperature

IP 54

-25°C to +70°C

Ordering information

FMC-300RW-GSGBU Manual call point, glass, blue

conventional manual call point with glass pane for indoor use, direct alarm triggering (type A), surface-mounted, blue Order number FMC-300RW-GSGBU | F.01U.012.724

FMC-300RW-GSRBU Manual call point, resettable, blue

resettable conventional manual call point for indoor use, direct alarm triggering (type A), surface-mounted, blue Order number FMC-300RW-GSRBU | F.01U.012.770

FMC-300RW-GSGRD Manual call point glass surfacemnt, red

conventional manual call point with glass pane for indoor use, direct alarm triggering (type A), surface-mounted, red Order number FMC-300RW-GSGRD | F.01U.012.771

FMC-300RW-GSRRD Manual call point reset surfacemnt, red

resettable conventional manual call point for indoor use, direct alarm triggering (type A), surface-mounted, red Order number FMC-300RW-GSRRD | F.01U.012.777

FMC-300RW-GSGYE Manual call point, glass, yellow

conventional manual call point with glass pane for indoor use, direct alarm triggering (type A), surface-mounted, yellow Order number FMC-300RW-GSGYE | F.01U.012.778

FMC-300RW-GSRYE Manual call point, resettable, yellow

resettable conventional manual call point for indoor use, direct alarm triggering (type A), surface-mounted, yellow Order number FMC-300RW-GSRYE | F.01U.012.779

Accessories

FMC-BEZEL-RD Bezel for manual call point, red

Frame for the flush-mounted variant of the RW call points. 1 unit = 4 bezels Order number FMC-BEZEL-RD | F.01U.073.045

FMC-BEZEL-WH Bezel for manual call point, white

Frame for the flush-mounted variant of the RW call points. 1 unit = 4 bezels Order number FMC-BEZEL-WH | F.01U.073.046

FMC-SEAL-RW Seal for manual call point

Seal for clear hinged flap 1 unit = 100 seals Order number FMC-SEAL-RW | F.01U.073.214

FMC-SPACER-RWRD Spacer, red

For the flush-mounted variant of the RW call points. Its use increases the storage room for the cables. 1 unit = 5spacers Order number FMC-SPACER-RWRD | F.01U.013.460

FMC-SPGL-RW Spare glass

Spare glasses for all RW call points. 1 unit = 5 spare glasses Order number FMC-SPGL-RW | F.01U.013.504

FMC-SIGN-RW Sign, out-of-order

Used instead of the glass pane when a call point is not ready for use. 1 unit = 5 signs Order number FMC-SIGN-RW | F.01U.028.195

FMC-KEY-RW Test key

The key can open, check, and reset manual call points. 1 unit = 1 key Order number FMC-KEY-RW | F.01U.028.227

FMC-FLAP-RW Flap, transparent

To protect against accidental triggering; with seal. 1 unit = 5 flaps Order number FMC-FLAP-RW | F.01U.028.194

+ 1 hidden pages