D7030X-S8
Installation Guide
EN Eight-Zone LED
Annunciator
D7030X-S8 | Installation Guide | Notices
Notices
This guide coves the installation of the D7030X-S8 Eight-Zone LED Annunicator in a fire system supervised by a D7024 Fire Alarm Control Panel (FACP).
Install, test, and maintain the D7030X-S8 according to these instructions, NFPA 72, local codes, and the Authority Having Jurisdiction (AHJ).
Follow the procedures in this guide to avoid personal injury and damage to the equipment. Failure to follow procedures can cause the D7030X-S8 to not operate properly. Bosch is not responsible for improperly installed, tested, or maintained devices.
1.0Description
All eight zones of the D7030X-S8 are reserved for supervisory functions. This annunciator has power, trouble, and eight zone LEDs that can be individually labeled. It mounts in a standard three-gang box (Figure 1).
Figure 1: D7030X-S8 Features
|
1 |
|
|
|
|
3 |
|
POWER |
|
|
1 |
8 |
|
|
|
|
|
|
|
|
|
ON |
|
|
Y |
|
|
|
|
|
|
|
|
|
|
SYSTEM |
|
|
G |
|
|
|
|
|
B |
|
8 |
|
|
TROUBLE |
|
|
|
||
|
|
|
|
R |
|
4 |
|
FIRE SYSTEM |
|
|
|
|
|
|
|
|
|
|
|
|
|
ANNUNCIATOR |
|
|
|
|
1 |
|
|
|
|
|
|
|
|
|
|
|
|
16 LED 8 LED |
5 |
|
|
|
|
|
16 LED ENABLE To CTRL-X |
|
|
2 |
10 |
9 |
8 |
7 |
6 |
1 - |
Front outside view |
|
6 - |
LED enable jumpers |
||
2 - |
Yellow zone LEDs (8) |
|
7 - |
8 and 16 zone selection |
||
3 - |
Inside view |
|
8 - |
To D7032 (optional) |
||
4 - |
Address jumpers |
|
9 - To FACP option bus |
|||
5 - |
To D7031 (optional) |
|
10 - Remote LED pins |
|
For the D7030X-S8 to operate with the D7024, use control panel firmware version 2.0 or greater.
|
|
|
|
|
|
2 |
Bosch | 11/04 | 48176D |
D7030X-S8 | Installation Guide | 4.0 |
Wiring |
|
|
2.0Setting the Address
Figure 2 shows the fifteen annunciator addresses you can select from when setting the D7030X-S8 address.
Figure 2: Address Settings
Address 1 |
Address 2 |
Address 3 |
1 | 2 | 4 | 8 |
1 | 2 | 4 | 8 |
1 | 2 | 4 | 8 |
|
Address 4 |
|
|
Address 5 |
|
|
Address 6 |
|
|||
1 | |
2 | |
4 | |
8 |
1 | |
2 | |
4 | |
8 |
1 | |
2 | |
4 | |
8 |
|
|
Address 7 |
|
|
|
|
Address 8 |
|
|
|
|
Address 9 |
|
|
||||||
1 |
| |
2 |
| |
4 |
| |
8 |
1 |
| |
2 |
| |
4 |
| |
8 |
1 |
| |
2 |
| |
4 |
| |
8 |
|
|
Address 10 |
|
|
|
Address 11 |
|
|
|
|
Address 12 |
|
||||||||
1 |
| |
2 |
| |
4 |
| |
8 |
1 |
| |
2 |
| |
4 |
| |
8 |
1 |
| |
2 |
| |
4 |
| |
8 |
|
|
Address 13 |
|
|
|
Address 14 |
|
|
|
Address 15 |
|
1 | |
2 | |
4 | |
8 |
1 | |
2 | |
4 | |
8 |
1 | |
2 | |
4 | |
8 |
The D7030X-S8 must have a unique address set within its address pins. This address cannot conflict with other annunciator addresses or other option bus device addresses. Program the D7030X-S8 at the control panel using the Update Bus option in the Programming Mode.
Each address can only support one device.
3.0Setting the LED Jumpers
Set the LED jumpers to 8 LED (zones) and 8 LED ENABLED as shown in Figure 3. When adding a D7032 Eight-Zone LED Expander, refer to the D7032 Installation Guide (P/N: 47169) for jumper settings.
Figure 3: Jumper Settings
1 |
8 |
|
|
Y |
|
|
|
G |
|
|
8 |
B |
|
|
|
R |
|
|
|
|
|
|
1 |
|
16 LED 8 LED |
16 LED ENABLE |
To CTRL-X |
|
|
1 |
2 |
|
|
16 LED 8 LED |
16 LED ENABLED |
1 - |
16 |
LED 8 LED (jumper setting for 8 zones) |
|
2 - |
16 |
LED ENABLED (jumper setting for 8 LEDs |
|
|
enabled) |
|
4.0Wiring
Ensure all wiring is de-energized before routing.
Inform the operator and local AHJ before installing the D7030X-S8 in an existing system. Also, disconnect all power to the FACP.
1.Remove AC power from the system at the dedicated 120 VAC breaker.
2.Remove the standby battery power before making or removing any connections to the FACP.
3.Route the wiring from the control panel (Option Bus A or Option Bus B) through the three-gang box knockout and to the annunciator terminal strip (Figure 4).
Figure 4: |
D7030X-S8 Terminal Wiring |
|||
|
|
1 |
|
|
|
|
RA BAGA YA RB BBGB YB |
|
4 |
|
2 |
|
|
|
|
|
|
3 |
|
|
|
|
|
Y |
|
|
|
|
G |
|
|
|
|
B |
|
|
|
|
R |
1 - |
Control panel option bus |
3 - |
Option Bus B |
|
2 - |
Option Bus A |
4 - |
Terminal strip |
Note: Connect to either bus.
To prevent the D7030X-S8 from operating improperly, do not use Bus A and Bus B simultaneously. Use one or the other.
Bosch | 11/04 | 48176D |
3 |