Bosch AUTODOME inteox 7000i Installation Manual

AUTODOME inteox 7000i ‑ 2MP (in‑ceiling)

en

Installation Manual

AUTODOME inteox 7000i - 2MP (in-ceiling) Table of contents | en 3

Table of contents

1

Safety EN 4

1.1 About this Manual 4

1.2 Legal Information 4

1.3 Safety Precautions 4

1.4 Important Safety Instructions 4

1.5 Important Notices 8

1.6 Customer Support and Service 10
2

Unpacking 11

2.1 Parts List 11

2.2 Tools Required 11
3
4
5
6
7

Product description 12
Preparing the bubble 13
(Optional) Installing an SD Card 14
Replacing the trim ring and bubble 15
Installing the In-Ceiling Mount 16

7.1 Description 16

7.2 Dimensions 16

7.3 Prepare Drywall Ceiling for Installation 16

7.4 Preparing the Suspension Ceiling for Installation 16

7.5 Installing the Ceiling (IP54 Housing) Gasket 17

7.6 Attach Housing to the Interface Box 18

7.7 Secure Housing to Ceiling 19
8
9
10

Finalizing installation 21
Replacing an In-ceiling HD Acrylic Bubble 22
Connection 23

10.1 Connecting the AUTODOME camera to the PC 23

10.2 Power Cable and Wire Distances Guides 23

10.3 Ethernet Connections 24

10.4 Fiber Optic Ethernet Media Converter (Optional) 25

10.5 Alarms and Relay Connections 26

10.6 Audio Connections (Optional) 29
11

Troubleshooting 31

11.1 Rebooting the unit 31

11.2 Physical reset button 32

11.3 Customer Service and Support 34
12
13
14

Maintenance 35
Technical data 36
Support services and Bosch Academy 37

Bosch Security Systems

Installation Manual

2021-03 | 1.2 |

4 en | Safety EN AUTODOME inteox 7000i - 2MP (in-ceiling)

!

!

i

1 Safety EN

1.1 About this Manual

This manual has been compiled with great care and the information it contains has been
thoroughly verified. The text was complete and correct at the time of printing. Because of the
ongoing development of products, the content of the manual may change without notice.
Bosch Security Systems accepts no liability for damage resulting directly or indirectly from
faults, incompleteness, or discrepancies between the manual and the product described.

1.2 Legal Information

Copyright

This manual is the intellectual property of Bosch Security Systems, and is protected by
copyright. All rights reserved.

Trademarks

All hardware and software product names used in this document are likely to be registered
trademarks and must be treated accordingly.

1.3 Safety Precautions

Danger!

Indicates a hazardous situation which, if not avoided, will result in death or serious injury.

Warning!

Indicates a hazardous situation which, if not avoided, could result in death or serious injury.

Caution!

Indicates a hazardous situation which, if not avoided, could result in minor or moderate
injury.

Notice!

Indicates a situation which, if not avoided, could result in damage to the equipment or
environment, or data loss.

1.4 Important Safety Instructions

Read, follow, and retain for future reference all of the following safety instructions. Heed all
warnings on the unit and in the operating instructions before operating the unit.

1. Cleaning - Unplug the unit from the outlet before cleaning. Follow any instructions
provided with the unit. Generally, using a dry cloth for cleaning is sufficient, but a moist
fluff-free cloth or leather shammy may also be used. Do not use liquid cleaners or aerosol
cleaners.

2. Heat Sources - Do not install the unit near any heat sources such as radiators, heaters,
stoves, or other equipment (including amplifiers) that produce heat.

3. Ventilation - Any openings in the unit enclosure are provided for ventilation to prevent
overheating and ensure reliable operation. Do not block or cover these openings. Do not
place the unit in an enclosure unless proper ventilation is provided, or the manufacturer's
instructions have been adhered to.

2021-03 | 1.2 |

Installation Manual

Bosch Security Systems

AUTODOME inteox 7000i - 2MP (in-ceiling) Safety EN | en 5

4. Object and liquid entry - Never push objects of any kind into this unit through openings
as they may touch dangerous voltage points or short-out parts that could result in a fire
or electrical shock. Never spill liquid of any kind on the unit. Do not place objects filled
with liquids, such as vases or cups, on the unit.

5. Lightning - For added protection during a lightning storm, or when leaving this unit
unattended and unused for long periods, unplug the unit from the wall outlet and
disconnect the cable system. This will prevent damage to the unit from lightning and
power line surges.

6. Controls adjustment - Adjust only those controls specified in the operating instructions.
Improper adjustment of other controls may cause damage to the unit. Use of controls or
adjustments, or performance of procedures other than those specified, may result in
hazardous radiation exposure.

7. Overloading - Do not overload outlets and extension cords. This can cause fire or
electrical shock.

8. Power cord and plug protection - Protect the plug and power cord from foot traffic,
being pinched by items placed upon or against them at electrical outlets, and its exit from
the unit. For units intended to operate with 230VAC, 50Hz, the input and output power
cord must comply with the latest versions of IEC Publication 227 or IEC Publication 245.

9. Power disconnect - Units have power supplied to the unit whenever the power cord is
inserted into the power source, or when High Power-over-Ethernet (High PoE) power is
provided over the Ethernet CAT 5E/6 cable. The unit is operational only when the ON/OFF
switch is in the ON position. The power cord is the main power disconnect device for
switching off the voltage for all units. When High PoE or PoE+ (820.3at) is used to power
the unit, the power is provided over the Ethernet cable, which is then the main power
disconnect device for switching off the voltage for all units.

10. Power sources - Operate the unit only from the type of power source indicated on the
label. Before proceeding, be sure to disconnect the power from the cable to be installed
into the unit.
For battery powered units, refer to the operating instructions.
For external power supplied units, use only the recommended or approved power
supplies.
For limited power source units, this power source must comply with EN60950.
Substitutions may damage the unit or cause fire or shock.
For 24VAC units, voltage applied to the unit's power input should not exceed ±10%, or
28VAC. User-supplied wiring must comply with local electrical codes (Class 2 power
levels). Do not ground the supply at the terminals or at the unit's power supply terminals.
If unsure of the type of power supply to use, contact your dealer or local power company.

11. Servicing - Do not attempt to service this unit yourself. Opening or removing covers may
expose you to dangerous voltage or other hazards. Refer all servicing to qualified service
personnel.

12. Damage requiring service - Unplug the unit from the main AC power source and refer
servicing to qualified service personnel when any damage to the equipment has occurred,
such as:
the power supply cord or plug is damaged;
exposure to moisture, water, and/or inclement weather (rain, snow, etc.);
liquid has been spilled in or on the equipment;
an object has fallen into the unit;
unit has been dropped or the unit cabinet is damaged;
unit exhibits a distinct change in performance;

Bosch Security Systems

Installation Manual

2021-03 | 1.2 |

6 en | Safety EN AUTODOME inteox 7000i - 2MP (in-ceiling)

!

!

!

!

i

i

unit does not operate normally when the user correctly follows the operating instructions.

13. Replacement parts - Be sure the service technician uses replacement parts specified by
the manufacturer, or that have the same characteristics as the original parts.
Unauthorized substitutions may cause fire, electrical shock, or other hazards.

14. Safety check - Safety checks should be performed upon completion of service or repairs
to the unit to ensure proper operating condition.

15. Installation - Install in accordance with the manufacturer's instructions and in accordance
with applicable local codes.

16. Attachments, changes or modifications - Only use attachments/accessories specified by
the manufacturer. Any change or modification of the equipment, not expressly approved
by Bosch, could void the warranty or, in the case of an authorization agreement, authority
to operate the equipment.

Caution!

Installation must be made by qualified personnel and conform to ANSI/NFPA 70 (the National
Electrical Code® (NEC)), Canadian Electrical Code, Part I (also called CE Code or CSA C22.1),
and all applicable local codes. Bosch Security Systems accepts no liability for any damages or
losses caused by incorrect or improper installation.

Warning!

INSTALL EXTERNAL INTERCONNECTING CABLES IN ACCORDANCE TO NEC, ANSI/NFPA70
(FOR US APPLICATION) AND CANADIAN ELECTRICAL CODE, PART I, CSA C22.1 (FOR CAN
APPLICATION) AND IN ACCORDANCE TO LOCAL COUNTRY CODES FOR ALL OTHER
COUNTRIES. BRANCH CIRCUIT PROTECTION INCORPORATING A 20 A, 2-POLE LISTED
CIRCUIT BREAKER OR BRANCH RATED FUSES ARE REQUIRED AS PART OF THE BUILDING
INSTALLATION. A READILY ACCESSIBLE 2-POLE DISCONNECT DEVICE WITH A CONTACT
SEPARATION OF AT LEAST 3 mm MUST BE INCORPORATED.

Warning!

ROUTING OF EXTERNAL WIRING MUST BE DONE THROUGH A PERMANENTLY EARTHED
METAL CONDUIT.

Warning!

THE CAMERA MUST BE MOUNTED DIRECTLY AND PERMANENTLY TO A NON-COMBUSTIBLE
SURFACE.

Notice!

Always use a shielded twisted pair (STP) connection cable and a shielded RJ45 network cable
connector where the camera is used outdoors or the network cable is routed outdoors.
Always use shielded cables/connectors in demanding indoor electrical environments where
the network cable is located in parallel with electrical mains supply cables, or where large
inductive loads such as motors or contactors are near the camera or its cable.

Notice!

Bosch recommends the use of surge/lightning protection devices (sourced locally) to protect
network and power cables and the camera installation site. Refer to NFPA 780, Class 1 & 2,
UL96A, or the equivalent code appropriate for your country/region, and to local building
codes. Refer also to the installation instructions of each device (surge protector where the
cable enters the building, midspan, and camera).

2021-03 | 1.2 |

Installation Manual

Bosch Security Systems

AUTODOME inteox 7000i - 2MP (in-ceiling) Safety EN | en 7

If a power adapter supplies power to the camera, you must ground the adapter properly.

Bosch Security Systems

Installation Manual

2021-03 | 1.2 |

8 en | Safety EN AUTODOME inteox 7000i - 2MP (in-ceiling)

1.5 Important Notices

Accessories - Do not place this unit on an unstable stand, tripod, bracket, or

mount. The unit may fall, causing serious injury and/or serious damage to
the unit. Use only with mounting solutions specified by the manufacturer.
When a cart is used, use caution and care when moving the cart/unit
combination to avoid injury from tip-over. Quick stops, excessive force, or
uneven surfaces may cause the cart/unit combination to overturn. Mount the
unit per the installation instructions.

Adjustment of controls - Adjust only those controls specified in the operating instructions.
Improper adjustment of other controls may cause damage to the unit.
Camera signal - Protect the cable with a primary protector if the camera signal is beyond 140
feet, in accordance with NEC800 (CEC Section 60).
Environmental statement - Bosch has a strong commitment towards the environment. This
device has been designed to respect the environment as much as possible.
Electrostatic-sensitive device - Use proper ESD safety precautions when handling the camera
to avoid electrostatic discharge.
Fuse rating - For security protection of the device, the branch circuit protection must be
secured with a maximum fuse rating of 16A. This must be in accordance with NEC800 (CEC
Section 60).

Grounding:

- Connect outdoor equipment to the unit's inputs only after this unit has had its ground

terminal connected properly to a ground source.

- Disconnect the unit's input connectors from outdoor equipment before disconnecting the

grounding terminal.

- Follow proper safety precautions such as grounding for any outdoor device connected to this

unit.
U.S.A. models only - Section 810 of the National Electrical Code, ANSI/NFPA No.70, provides
information regarding proper grounding of the mount and supporting structure, size of
grounding conductors, location of discharge unit, connection to grounding electrodes, and
requirements for the grounding electrode.
Outdoor signals - The installation for outdoor signals, especially regarding clearance from
power and lightning conductors and transient protection, must be in accordance with NEC725
and NEC800 (CEC Rule 16-224 and CEC Section 60).
Refer to the ”Best Practices for Outdoor Installation” section of the manual for more
information on outdoor installations.
Permanently connected equipment - Incorporate a readily accessible disconnect device in the
building installation wiring.
Power lines - Do not locate the camera near overhead power lines, power circuits, or
electrical lights, nor where it may contact such power lines, circuits, or lights.
Damage requiring service – Unplug the devices from the main AC power source and refer
servicing to qualified service personnel whenever any damage to the device has occurred,
such as:

- the power supply cable is damaged;

- an object has fallen on the device;

- the device has been dropped, or its enclosure has been damaged;

- the device does not operate normally when the user follows the operating instructions

correctly.

2021-03 | 1.2 |

Installation Manual

Bosch Security Systems

AUTODOME inteox 7000i - 2MP (in-ceiling) Safety EN | en 9

i

i

Servicing - Do not attempt to service this device yourself. Refer all servicing to qualified
service personnel.
This device has no user-serviceable parts.

Notice!

This is a class A product. In a domestic environment this product may cause radio
interference, in which case the user may be required to take adequate measures.

Notice!

Ce produit est un appareil de Classe A. Son utilisation dans une zone résidentielle risque de
provoquer des interférences. Le cas échéant, l’utilisateur devra prendre les mesures
nécessaires pour y remédier.

Bosch Security Systems

Installation Manual

2021-03 | 1.2 |

10 en | Safety EN AUTODOME inteox 7000i - 2MP (in-ceiling)

FCC & ICES Information

(U.S.A. and Canadian Models Only)
This device complies with part 15 of the FCC Rules. Operation is subject to the following
conditions:
– this device may not cause harmful interference, and
– this device must accept any interference received, including interference that may cause

undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules and ICES-003 of Industry Canada. These
limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and
radiates radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference, in which case the
user will be required to correct the interference at his expense.
Intentional or unintentional modifications, not expressly approved by the party responsible for
compliance, shall not be made. Any such modifications could void the user's authority to
operate the equipment. If necessary, the user should consult the dealer or an experienced
radio/television technician for corrective action.

1.6 Customer Support and Service

If this unit needs service, contact the nearest Bosch Security Systems Service Center for
authorization to return and shipping instructions.
USA and Canada
Telephone: [phone], option 5
Fax: [phone]
Email: [e-mail]

Customer Service

Telephone: [phone], option 3
Fax: [phone]
Email: [e-mail]

Technical Support

Telephone: [phone], option 4
Fax: [phone]
Email: [e-mail]
Europe, Middle East, Africa, and Asia Pacific Regions
Contact your local distributor or Bosch sales office. Use this link: https://

www.boschsecurity.com/xc/en/where-to-buy/

More Information

For more information, please contact the nearest Bosch Security Systems location or visit

www.boschsecurity.com.

2021-03 | 1.2 |

Installation Manual

Bosch Security Systems

AUTODOME inteox 7000i - 2MP (in-ceiling) Unpacking | en 11

2 Unpacking

– This equipment should be unpacked and handled with care. Check the exterior of the

packaging for visible damage. If an item appears to have been damaged in shipment,
notify the shipper immediately.

– Verify that all the parts listed in the Parts List below are included. If any items are

missing, notify your Sales or Customer Service Representative from Bosch Security
Systems.

– Do not use this product if any component appears to be damaged. Please contact Bosch

Security Systems in the event of damaged goods.

– The original packing carton (if undamaged) is the safest container in which to transport

the unit and must be used if returning the unit for service. Save it for possible future use.

2.1 Parts List

Quantity Component

1 AUTODOME inteox 7000i in-ceiling camera

1 Interface box

1 Optional black trim ring

1 Ceiling gasket (for IP54 conformance)

1 Safety instructions

1 Quick Installation Guide

2.2 Tools Required

1 Appropriate tool for

cutting a hole in drywall
or ceiling tile

1 Pliers In-ceiling Mount No

The following table lists additional products, sold separately by Bosch or other manufacturers,
necessary to install AUTODOME cameras.

Quantity Product Part Number Size

1 SD card (user-supplied)

--- Water tight metal conduit (user-supplied) 20 mm (0.75 in.)

-- UL-listed liquid tight strain reliefs (user-supplied)

-- Weatherproof sealant (user-supplied)

4 Studs, stainless steel, corrosion-

resistant,

In-ceiling Mount No

(user-supplied) 6.4 mm (0.25 in.)

to 8 mm (5/16 in.)

Bosch Security Systems

Installation Manual

2021-03 | 1.2 |

12 en | Product description AUTODOME inteox 7000i - 2MP (in-ceiling)

3 Product description

The AUTODOME inteox 7000i camera is an advanced, 30x PTZ surveillance camera based on
an open operating system, driven by OSSA, from Security and Safety Things. With starlight
imaging technology for excellent low-light sensitivity, the most robust Video Analytics on the
market, and video streaming, the camera delivers unmatched picture quality. Even under the
most challenging light conditions, the camera delivers high-definition (HD) 1080p video. Easy
to install, the camera is available in either a field-proven, outdoor pendant housing or an
indoor, in-ceiling housing.
The camera has been designed for quick and easy installation, a key feature from Bosch IP
video security products.
All housings feature recessed screws and latches for increased tamper resistance.
In an enclosed installation area, still air can cause the operating temperature of the camera to
go above the maximum. If you install a camera in an enclosed area, make sure that the
operating temperature of the camera does not go above the maximum temperature. The
maximum operating temperature is:
– +40°C (+104°F) for in-ceiling models
– +55°C (+131°F) for pendant models
Make sure that air circulates around the camera to supply cooling.

2021-03 | 1.2 |

Installation Manual

Bosch Security Systems