bintec elmeg W2003ac User Manual

Business WLAN .11ac Access Point

bintec W2003ac

•

802.11ac/agbn 2x2 Mimo technology with up to 867 Mbit/s

•

Dual concurrent operation at 5GHz and 2,4 GHz

•

Enhanced feature set for performance optimizing

•

Managed operation or stand-alone operation

•

2 x Gigabit Ethernet with standard PoE (12,4W)

•

Certified for operation in medical environments

•

Inconspicuous housing design with swichtable LEDs

bintec W2003ac

Business WLAN .11ac Access Point

Budget 802.11ac Access Point with full performance support of .11ac devices, interoperable to
.11n devices

Product Description

The bintec W2003ac access point supports the new 802.11ac wireless standard. The dual radios
allow for simultaneous operation in both the 2.4 GHz and 5 GHz frequency bands. bintec Client
Management ensures that the wireless client is always able to operate at maximum speed.
bintec Client Management offers a wide range of features and also ensures that the client is
always connected to the access point that can provide the best performance.

MIMO 2x2 technology and the 802.11ac wireless standard allow for PHY data rates of up to 867
Mbps. The MIMO 2x2 technology with two transmission streams offers the considerable
advantage of requiring less than 12.4 watts of power, enabling operation on a standard low-cost
PoE infrastructure.
In addition, the MIMO 2x2 technology is an ideal match for current smartphones and tablet PCs,
which frequently only support 802.11ac with MIMO 1x1. Access points with the expensive MIMO
3x3 or MIMO 4x4 technology are not able to realize their full performance potential with these
types of terminal devices, which makes an access point operating on the 802.11 ac standard and
MIMO 2x2 the better solution and the better value.

The bintec W2003ac has an unobtrusive housing with internal antennas and LEDs that turn off.
The included wall and ceiling mounting bracket makes installation easy.

The access point be managed using the bintec Cloud NetManager or a locally installed bintec
WLAN Controller. Using the included free WLAN Controller license, you can operate this model as
a master-AP to manage a small wireless LAN with up to six access points. Of course you can also
configure the W2003ac to run as a stand-alone AP. It's hard to imagine greater flexibility.

Variants

bintec elmeg GmbH - Suedwestpark 94 - 90449 Nuremberg - Germany
Phone: +49 - 911 9673-0 - Telefax: +49 - 911 688 07 25
E-Mail: [e-mail] - www.bintec-elmeg.com

Subject to technical alterations

bintec W2003ac

31.05.2016

Page 2 / 8

bintec W2003ac (5510000395) WLAN Access Point with a dual concurrent radio module acc. 802.11ac/abgn (2.4/5

GHz) Mimo 2x2, 2 Gigabit ETH, PoE, integr. Antennas, incl. Wall/ceiling mounting,
incl. WLAN Controller license for Master AP, shipment without 100-240V wall
adapter

Features

Operation Modes

WLAN operation mode WLAN = off / WLAN = Access Point (stand-alone/Managed/Master-AP/Cloud Managed)

Wireless LAN (Radio 1)

WLAN Standards 802.11b; 802.11g; 802.11n (Mimo 2x2) 2.4 GHz

Receiver Sensitivity @ 2.4 GHz

802.11b/g

Receiver Sensitivity @ 2.4 GHz

802.11n 20 MHz

Receiver Sensitivity @ 2.4 GHz

802.11n 40 MHz

Tx Power @ 2.4 GHz 802.11b/g 1 Mbps 20 dBm; 2 Mbps 20 dBm; 5,5 Mbps 20 dBm; 11 Mbps 20 dBm; 6 Mbps 20 dBm; 9 Mbps 20

Tx Power @ 2.4 GHz 802.11n 20
MHz (2 chains)

Tx Power @ 2.4 GHz 802.11n 40
MHz (2 chains)

Frequency bands 2.4 GHz
indoor/outdoor (EU)

Data rates for 802.11b,g (2.4
GHz)

Data rates for 802.11n, 20 MHz
channel bandwidth

1 Mbps -94 dBm; 2 Mbps -94 dBm; 5,5 Mbps -94 dBm; 11 Mbps -94 dBm; 6 Mbps -94 dBm; 9 Mbps

-94 dBm; 12 Mbps -94 dBm; 18 Mbps -94 dBm; 24 Mbps -94 dBm; 36 Mbps -86 dBm; 48 Mbps -82
dBm; 54 Mbps -80 dBm

MCS0/8 -94 dBm; MCS1/9 -94 dBm; MCS2/10 -92 dBm; MCS3/11 -88 dBm; MCS4/12 -84 dBm;
MCS5/13 -81 dBm; MCS6/14 -78 dBm; MCS7/15 -77 dBm

MCS0/8 -93 dBm; MCS1/9 -91 dBm; MCS2/10 -90 dBm; MCS3/11 -85 dBm; MCS4/12 -82 dBm;
MCS5/13 -78 dBm; MCS6/14 -77 dBm; MCS7/15 -75 dBm

dBm; 12 Mbps 20 dBm; 18 Mbps 20 dBm; 24 Mbps 20 dBm; 36 Mbps 20 dBm; 48 Mbps 20 dBm; 54
Mbps 18 dBm

MCS0/8 20 dBm; MCS1/9 20 dBm; MCS2/10 20 dBm; MCS3/11 20 dBm; MCS4/12 20 dBm; MCS5/13
20 dBm; MCS6/14 18 dBm; MCS7/16 15 dBm

MCS0/8 20 dBm; MCS1/9 20 dBm; MCS2/10 20 dBm; MCS3/11 20 dBm; MCS4/12 20 dBm; MCS5/13
20 dBm; MCS6/14 18 dBm; MCS7/15 16 dBm

2.4 GHz Indoor/Outdoor (2412-2484 MHz) max. 100 mW EiRP (for Germany)

11, 5.5, 2 und 1 Mbps (DSSS modulation); 54, 48, 36, 24, 18, 12, 9 and 6 Mbps (OFDM modulation)

MCS0-15 allow up to 150 Mbps PHY rate at 20 MHz channel bandwidth, 2 streams, Short guard
intervall

Data rates for 802.11n, 40 MHz
channel bandwidth

Output power limitation (
without antenna gain)

Output power @ 2.4 GHz Max. 20dBm

Automatic Rate Selection (ARS) Available

Transmission rate Automatic

MCS0-15 allow up to 300 Mbps PHY rate at 40 MHz channel bandwidth, 2 streams, Short guard
intervall

Adjustable in following steps: 5, 8,11,14,16 dBm and maximum. Maximal power varies depending
on data rate, frequency band and country setting.

bintec elmeg GmbH - Suedwestpark 94 - 90449 Nuremberg - Germany
Phone: +49 - 911 9673-0 - Telefax: +49 - 911 688 07 25
E-Mail: [e-mail] - www.bintec-elmeg.com

bintec W2003ac

31.05.2016

Subject to technical alterations

Page 3 / 8