BFT EOS 1200 U Installation And User Manual

ISTRUZIONI D’USO E DI INSTALLAZIONE

INSTALLATION AND USER’S MANUAL

INSTRUCTIONS D’UTILISATION ET D’INSTALLATION

INSTALLATIONS-UND GEBRAUCHSANLEITUNG

INSTRUCCIONES DE USO Y DE INSTALACION

GEBRUIKS- EN INSTALLATIEAANWIJZINGEN

D812774 00100_06 02-11-16

AUTOMAZIONI PER PORTE BASCULANTI E SEZIONALI
AUTOMATION FOR OVERHEAD AND SECTIONAL GARAGE DOORS
AUTOMATION POUR PORTES BASCULANTES ET SECTIONALES
GARAGENTORANTRIEB FÜR SCHWING UND SEKTIONALTORE
AUTOMATIZACIONES PARA PUERTAS BASCULANTE Y SECCIONALES
AUTOMATISERINGEN VOOR KANTEL- EN SECTIEDEUREN

Attenzione! Leggere attentamente le “Avvertenze” all’interno! Caution! Read “Warnings” inside carefully! Attention! Veuillez lire attentivement les Avertissements qui se trouvent à l’intérieur!
Achtung! Bitte lesen Sie aufmerksam die „Hinweise“ im Inneren! ¡Atención¡ Leer atentamente las “Advertencias”en el interior! Let op! Lees de “Waarschuwingen” aan de binnenkant zorgvuldig!

EOS 1200 U

D812774 00100_06

2 - EOS 1200 U

AVVERTENZE PER L’UTILIZZATORE ( I )

ATTENZIONE! Importanti istruzioni di sicurezza.
Leggere e seguire attentamente le Avvertenze
e le Istruzioni che accompagnano il prodotto
poiché un uso improprio può causare danni a
persone, animali o cose. Conservare le istruzioni
per consultazioni future e trasmetterle ad even­tuali subentranti nell’uso dell’impianto.
Questo prodotto dovrà essere destinato solo
all’uso per il quale è stato espressamente insta­llato. Ogni altro uso è da considerarsi improprio
e quindi pericoloso. Il costruttore non può essere
considerato responsabile per eventuali danni
causati da usi impropri, erronei e irragionevoli.
SICUREZZA GENERALE

Nel ringraziarVi per la preferenza accordata a questo
prodotto, la Ditta è certa che da esso otterrete le
prestazioni necessarie al Vostro uso.
Questo prodotto risponde alle norme riconosciute
della tecnica e della disposizioni relative alla si­curezza se correttamente installato da personale
qualicato ed esperto (installatore professionale).
L’automazione, se installata ed utilizzata corretta­mente, soddisfa gli standard di sicurezza nell’uso.
Tuttavia è opportuno osservare alcune regole di
comportamento per evitare inconvenienti acci­dentali:

- Tenere bambini, persone e cose fuori dal raggio
d’azione dell’automazione, in particolare durante
il movimento.

- Non permettere a bambini di giocare o sostare nel
raggio di azione dell’automazione.

- L’apparecchio può essere utilizzato da bambini di
età non inferiore a 8 anni e da persone con ridot­te capacità siche, sensoriali o mentali, o prive di
esperienza o della necessaria conoscenza, purché
sotto sorveglianza oppure dopo che le stesse
abbiano ricevuto istruzioni relative all’uso sicuro
dell’apparecchio e alla comprensione dei pericoli
ad esso inerenti. I bambini non devono giocare con
l’apparecchio. La pulizia e la manutenzione desti­nata ad essere eettuata dall’utilizzatore non deve
essere eettuata da bambini senza sorveglianza.

- I bambini devono essere sorvegliati per sincerarsi
che non giochino con l’apparecchio. Non permet­tere ai bambini di giocare con i controlli ssi. Tenere
i telecomandi lontani dai bambini.

-

Evitare di operare in prossimità delle cerniere o organi
meccanici in movimento.

-

Non contrastare il movimento dell’anta e non ten­tare di aprire manualmente la porta se non è stato
sbloccato l’attuatore con l’apposito sblocco.

-

Non entrare nel raggio di azione della porta o can­cello motorizzati durante il loro movimento.

- Non lasciare radiocomandi o altri dispositivi di
comando alla portata dei bambini onde evitare
azionamenti involontari.

- L’attivazione dello sblocco manuale potrebbe
causare movimenti incontrollati della porta se in
presenza di guasti meccanici o di condizioni di
squilibrio.

- In caso di apritapparelle: sorvegliare la tapparella
in movimento e tenere lontano le persone nché
non è completamente chiusa. Porre cura quando si
aziona lo sblocco se presente, poiché una tapparella
aperta potrebbe cadere rapidamente in presenza
di usura o rotture.

-

La rottura o l’usura di organi meccanici della porta
(parte guidata), quali ad esempio cavi, molle, sup-

porti, cardini, guide.. potrebbe generare pericoli. Far
controllare periodicamente l’impianto da personale
qualicato ed esperto (installatore professionale)
secondo quanto indicato dall’installatore o dal
costruttore della porta.

- Per ogni operazione di pulizia esterna, togliere
l’alimentazione di rete.

- Tenere pulite le ottiche delle fotocellule ed i dispo­sitivi di segnalazione luminosa. Controllare che rami
ed arbusti non disturbino i dispositivi di sicurezza.

- Non utilizzare l’automatismo se necessita di
interventi di riparazione. In caso di guasto o di
malfunzionamento dell’automazione, togliere
l’alimentazione di rete sull’automazione, astenersi
da qualsiasi tentativo di riparazione o intervento
diretto e rivolgersi solo a personale qualicato ed
esperto (installatore professionale) per la neces­saria riparazione o manutenzione. Per consentire
l’accesso, attivare lo sblocco di emergenza (se
presente).

-

Per qualsiasi intervento diretto sull’automazione o
sull’impianto non previsto dal presente manuale,
avvalersi di personale qualicato ed esperto (insta­llatore professionale).

- Con frequenza almeno annuale far verifi­care l’integrità e il corretto funzionamento
dell’automazione da personale qualificato ed
esperto (installatore professionale), in particolare
di tutti i dispositivi di sicurezza.

- Gli interventi d’installazione, manutenzione e
riparazione devono essere documentati e la
relativa documentazione tenuta a disposizione
dell’utilizzatore.

- Il mancato rispetto di quanto sopra può creare
situazioni di pericolo.

DEMOLIZIONE

L’eliminazione dei materiali va fatta rispettan-

do le norme vigenti. Non gettate il vostro
apparecchio scartato, le pile o le batterie usate
nei riuti domestici. Avete la responsabilità di
restituire tutti i vostri riuti da apparecchia­ture elettriche o elettroniche lasciandoli in
un punto di raccolta dedicato al loro riciclo.

Tutto quello che non è espressamente previs­to nel manuale d’uso, non è permesso. ll buon
funzionamento dell’operatore è garantito solo
se vengono rispettate le prescrizioni riportate
in questo manuale. La Ditta non risponde dei
danni causati dall’inosservanza delle indicazioni
riportate in questo manuale.
Lasciando inalterate le caratteristiche essenziali
del prodotto, la Ditta si riserva di apportare in
qualunque momento le modiche che essa ritie­ne convenienti per migliorare tecnicamente, cos­truttivamente e commercialmente il prodotto,
senza impegnarsi ad aggiornare la presente
pubblicazione.

USER WARNINGS (GB)

WARNING! Important safety instructions. Ca­refully read and comply with the Warnings and
Instructions that come with the product as impro­per use can cause injury to people and animals
and damage to property. Keep the instructions
for future reference and hand them on to any
new users.
This product is meant to be used only for the
purpose for which it was explicitly installed.

D811767_08

Any other use constitutes improper use and,
consequently, is hazardous. The manufacturer
cannot be held liable for any damage as a result
of improper, incorrect or unreasonable use.
GENERAL SAFETY

Thank you for choosing this product. The Firm is
condent that its performance will meet your ope-
rating needs.
This product meets recognized technical standards
and complies with safety provisions when installed
correctly by qualied, expert personnel (professional
installer).
If installed and used correctly, the automated system
will meet operating safety standards. Nonetheless,
it is advisable to observe certain rules of behaviour
so that accidental problems can be avoided:

- Keep adults, children and property out of range of
the automated system, especially while it is moving.

- Do not allow children to play or stand within range
of the automated system.

- The unit can be used by children over 8 years old
and by people with reduced physical, sensory or
mental capabilities or with no experience or neces-
sary knowledge on condition they are supervised
or trained about the safe use of the equipment
and understand the risks involved. Children must
not play with the unit. Cleaning and maintenance
must not be performed by unsupervised children.

- Children must be supervised to ensure they do not
play with the device. Do not allow children to play
with the xed controls. Keep remote controls out
of reach of children.

-

Do not work near hinges or moving mechanical parts.

- Do not hinder the leaf’s movement and do not
attempt to open the door manually unless the ac-
tuator has been released with the relevant release
knob.

- Keep out of range of the motorized door or gate
while they are moving.

- Keep remote controls or other control devices out
of reach of children in order to avoid the automated
system being operated inadvertently.

- The manual release’s activation could result in un-
controlled door movements if there are mechanical
faults or loss of balance.

- When using roller shutter openers: keep an eye
on the roller shutter while it is moving and keep
people away until it has closed completely. Exercise
care when activating the release, if such a device
is tted, as an open shutter could drop quickly in
the event of wear or breakage.

- The breakage or wear of any mechanical parts of
the door (operated part), such as cables, springs,
supports, hinges, guides…, may generate a hazard.
Have the system checked by qualied, expert per-
sonnel (professional installer) at regular intervals
according to the instructions issued by the installer
or manufacturer of the door.

- When cleaning the outside, always cut o mains
power.

- Keep the photocells’ optics and illuminating in-
dicator devices clean. Check that no branches or
shrubs interfere with the safety devices.

- Do not use the automated system if it is in need of
repair. In the event the automated system breaks
down or malfunctions, cut o mains power to the
system; do not attempt to repair or perform any
other work to rectify the fault yourself and instead
call in qualied, expert personnel (professional
installer) to perform the necessary repairs or main-

tenance. To allow access, activate the emergency
release (where tted).

- If any part of the automated system requires direct
work of any kind that is not contemplated herein,
employ the services of qualied, expert personnel
(professional installer).

- At least once a year, have the automated system, and
especially all safety devices, checked by qualied,
expert personnel (professional installer) to make
sure that it is undamaged and working properly.

- A record must be made of any installation, main-
tenance and repair work and the relevant docu-
mentation kept and made available to the user on
request.

- Failure to comply with the above may result in
hazardous situations.

SCRAPPING

Materials must be disposed of in accordance

with the regulations in force. Do not throw
away your discarded equipment or used bat-
teries with household waste. You are respon-
sible for taking all your waste electrical and
electronic equipment to a suitable recycling
centre.

Anything that is not explicitly provided for in the
user guide is not allowed. The operator’s proper
operation can only be guaranteed if the instruc-
tions given herein are complied with. The Firm
shall not be answerable for damage caused by
failure to comply with the instructions featured
herein.
While we will not alter the product’s essential
features, the Firm reserves the right, at any time,
to make those changes deemed opportune to
improve the product from a technical, design or
commercial point of view, and will not be required
to update this publication accordingly.

AVERTISSEMENTS POUR L’UTILISATEUR (F)

ATTENTION ! Instructions de sécurité importan-
tes. Veuillez lire et suivre attentivement tous les
avertissements et toutes les instructions fournis
avec le produit sachant qu’un usage incorrect
peut provoquer des préjudices aux personnes,
aux animaux ou aux biens. Veuillez conserver
les instructions pour d’ultérieures consultations
et pour les transmettre aux propriétaires futurs
éventuels.
Cet appareil ne peut être destiné qu’à l’usage
pour lequel il a été expressément installé. Tout
autre usage sera considéré comme impropre et
donc dangereux. Le fabricant ne sera en aucun
cas considéré comme responsable des préjudices
dus à un usage impropre, erroné ou déraisonné.
SECURITE GÉNÉRALE

Nous vous remercions d’avoir choisi ce produit
qui, nous n’en doutons pas, saura vous garantir les
performances attendues.
Ce produit, correctement installé par du personnel
qualié et expérimenté (monteur professionnel) est
conforme aux normes reconnues de la technique et
des prescriptions de sécurité.
Si l’automatisation est montée et utilisée correcte-
ment, elle garantit la sécurité d’utilisation prescrite.
Il est cependant nécessaire de respecter certaines
règles de comportement pour éviter tout inconvé-
nient accidentel.

- Tenir les enfants, les personnes et les objets à l’écart

D811767_08

D812774 00100_06

EOS 1200 U - 3

Any other use constitutes improper use and,
consequently, is hazardous. The manufacturer
cannot be held liable for any damage as a result
of improper, incorrect or unreasonable use.
GENERAL SAFETY

Thank you for choosing this product. The Firm is
condent that its performance will meet your ope­rating needs.
This product meets recognized technical standards
and complies with safety provisions when installed
correctly by qualied, expert personnel (professional
installer).
If installed and used correctly, the automated system
will meet operating safety standards. Nonetheless,
it is advisable to observe certain rules of behaviour
so that accidental problems can be avoided:

- Keep adults, children and property out of range of
the automated system, especially while it is moving.

- Do not allow children to play or stand within range
of the automated system.

- The unit can be used by children over 8 years old
and by people with reduced physical, sensory or
mental capabilities or with no experience or neces­sary knowledge on condition they are supervised
or trained about the safe use of the equipment
and understand the risks involved. Children must
not play with the unit. Cleaning and maintenance
must not be performed by unsupervised children.

- Children must be supervised to ensure they do not
play with the device. Do not allow children to play
with the xed controls. Keep remote controls out
of reach of children.

-

Do not work near hinges or moving mechanical parts.

- Do not hinder the leaf’s movement and do not
attempt to open the door manually unless the ac­tuator has been released with the relevant release
knob.

- Keep out of range of the motorized door or gate
while they are moving.

- Keep remote controls or other control devices out
of reach of children in order to avoid the automated
system being operated inadvertently.

- The manual release’s activation could result in un­controlled door movements if there are mechanical
faults or loss of balance.

- When using roller shutter openers: keep an eye
on the roller shutter while it is moving and keep
people away until it has closed completely. Exercise
care when activating the release, if such a device
is tted, as an open shutter could drop quickly in
the event of wear or breakage.

- The breakage or wear of any mechanical parts of
the door (operated part), such as cables, springs,
supports, hinges, guides…, may generate a hazard.
Have the system checked by qualied, expert per­sonnel (professional installer) at regular intervals
according to the instructions issued by the installer
or manufacturer of the door.

- When cleaning the outside, always cut o mains
power.

- Keep the photocells’ optics and illuminating in­dicator devices clean. Check that no branches or
shrubs interfere with the safety devices.

- Do not use the automated system if it is in need of
repair. In the event the automated system breaks
down or malfunctions, cut o mains power to the
system; do not attempt to repair or perform any
other work to rectify the fault yourself and instead
call in qualied, expert personnel (professional
installer) to perform the necessary repairs or main-

tenance. To allow access, activate the emergency
release (where tted).

- If any part of the automated system requires direct
work of any kind that is not contemplated herein,
employ the services of qualied, expert personnel
(professional installer).

- At least once a year, have the automated system, and
especially all safety devices, checked by qualied,
expert personnel (professional installer) to make
sure that it is undamaged and working properly.

- A record must be made of any installation, main­tenance and repair work and the relevant docu­mentation kept and made available to the user on
request.

- Failure to comply with the above may result in
hazardous situations.

SCRAPPING

Materials must be disposed of in accordance

with the regulations in force. Do not throw
away your discarded equipment or used bat­teries with household waste. You are respon­sible for taking all your waste electrical and
electronic equipment to a suitable recycling
centre.

Anything that is not explicitly provided for in the
user guide is not allowed. The operator’s proper
operation can only be guaranteed if the instruc­tions given herein are complied with. The Firm
shall not be answerable for damage caused by
failure to comply with the instructions featured
herein.
While we will not alter the product’s essential
features, the Firm reserves the right, at any time,
to make those changes deemed opportune to
improve the product from a technical, design or
commercial point of view, and will not be required
to update this publication accordingly.

AVERTISSEMENTS POUR L’UTILISATEUR (F)

ATTENTION ! Instructions de sécurité importan­tes. Veuillez lire et suivre attentivement tous les
avertissements et toutes les instructions fournis
avec le produit sachant qu’un usage incorrect
peut provoquer des préjudices aux personnes,
aux animaux ou aux biens. Veuillez conserver
les instructions pour d’ultérieures consultations
et pour les transmettre aux propriétaires futurs
éventuels.
Cet appareil ne peut être destiné qu’à l’usage
pour lequel il a été expressément installé. Tout
autre usage sera considéré comme impropre et
donc dangereux. Le fabricant ne sera en aucun
cas considéré comme responsable des préjudices
dus à un usage impropre, erroné ou déraisonné.
SECURITE GÉNÉRALE

Nous vous remercions d’avoir choisi ce produit
qui, nous n’en doutons pas, saura vous garantir les
performances attendues.
Ce produit, correctement installé par du personnel
qualié et expérimenté (monteur professionnel) est
conforme aux normes reconnues de la technique et
des prescriptions de sécurité.
Si l’automatisation est montée et utilisée correcte­ment, elle garantit la sécurité d’utilisation prescrite.
Il est cependant nécessaire de respecter certaines
règles de comportement pour éviter tout inconvé­nient accidentel.

- Tenir les enfants, les personnes et les objets à l’écart

D811767_08

D812774 00100_06

8 - EOS 1200 U

MANUALE D’USO: MANOVRA MANUALE - USER’S MANUAL: MANUAL OPERATION

MANUEL D’UTILISATION: MANŒUVRE MANUELLE - BEDIENUNGSANLEITUNG: MANUELLES MANÖVER

MANUAL DE USO: ACCIONAMIENTO MANUAL - GEBRUIKSHANDLEIDING: MANUEEL MANOEUVRE

FIG. 1

1 2

+

O

N

O

F

F

AVVERTENZE PER L’INSTALLATORE

Tutto quello che non è espressamente previsto nel manuale d’installa-
zione, non è permesso. ll buon funzionamento dell’operatore è garantito
solo se vengono rispettati i dati riportati. La ditta non risponde dei danni
causati dall’inosservanza delle indicazioni riportate in questo manuale.
Lasciando inalterate le caratteristiche essenziali del prodotto, la Ditta
si riserva di apportare in qualunque momento le modiche che essa
ritiene convenienti per migliorare tecnicamente, costruttivamente
e commercialmente il prodotto, senza impegnarsi ad aggiornare la
presente pubblicazione.

ATTENZIONE! Importanti istruzioni di sicurezza. Leggere e seguire atten-
tamente tutte le avvertenze e le istruzioni che accompagnano il prodotto
poiché un’installazione errata può causare danni a persone, animali o cose.
Le avvertenze e le istruzioni forniscono importanti indicazioni riguardanti la
sicurezza, l’installazione, l’uso e la manutenzione. Conservare le istruzioni
per allegarle al fascicolo tecnico e per consultazioni future.

SICUREZZA GENERALE

Questo prodotto è stato progettato e costruito esclusivamente per l’utilizzo
indicato in questa documentazione. Usi diversi da quanto indicato potrebbero
essere causa di danni al prodotto e di pericolo.

- Gli elementi costruttivi della macchina e l’installazione devono essere in accor-
do con le seguenti Direttive Europee, ove applicabili: 2014/30/CE, 2014/35/CE,
2006/42/CE, 2011/305/CE, 99/05/CE e loro modiche successive. Per tutti i Paesi
extra CEE, oltre alle norme nazionali vigenti, per un buon livello di sicurezza è
opportuno rispettare anche le norme citate.

- La Ditta costruttrice di questo prodotto (di seguito “Ditta”) declina qualsiasi
responsabilità derivante da un uso improprio o diverso da quello per cui è
destinato e indicato nella presente documentazione nonché dall’inosservanza
della Buona Tecnica nella costruzione delle chiusure (porte, cancelli, ecc.) e dalle
deformazioni che potrebbero vericarsi durante l’uso.

- L’installazione deve essere eseguita da personale qualicato (installatore profes-
sionale, secondo EN12635), nell’osservanza della Buona Tecnica e delle norme
vigenti.

- Prima di installare il prodotto apportare tutte le modiche strutturali relative
alle realizzazione dei franchi di sicurezza a alla protezione o segregazione di
tutte le zone di schiacciamento, cesoiamento, convogliamento e di pericolo in
genere, secondo quanto previsto dalle norme EN 12604 ed 12453 o eventuali
norme locali di installazione. Vericare che la struttura esistente abbia i necessari
requisiti di robustezza e stabilità.

- Prima di iniziare l’installazione vericare l’integrità del prodotto.

- La Ditta non è responsabile della inosservanza della Buona Tecnica nella costru-
zione e manutenzione degli inssi da motorizzare, nonché delle deformazioni
che dovessero intervenire nell’utilizzo.

- Vericare che l’intervallo di temperatura dichiarato sia compatibile con il luogo
destinato all’installazione dell’automazione.

- Non installare questo prodotto in atmosfera esplosiva: la presenza di gas o fumi
inammabili costituisce un grave pericolo per la sicurezza.

- Togliere l’alimentazione elettrica, prima di qualsiasi intervento sull’impianto.
Scollegare anche eventuali batterie tampone se presenti.

- Prima di collegare l’alimentazione elettrica, accertarsi che i dati di targa corrispon-
dano ai quelli della rete di distribuzione elettrica e che a monte dell’impianto
elettrico vi siano un interruttore dierenziale e una protezione da sovracorrente
adeguati. Prevedere sulla rete di alimentazione dell’automazione, un interruttore
o un magnetotermico onnipolare che consenta la disconnessione completa nelle
condizioni della categoria di sovratensione III.

- Vericare che a monte della rete di alimentazione, vi sia un interruttore dieren-
ziale con soglia non superiore a 0.03A e a quanto previsto dalle norme vigenti.

- Vericare che l’impianto di terra sia realizzato correttamente: collegare a terra
tutte le parti metalliche della chiusura (porte, cancelli, ecc.) e tutti i componenti
dell’impianto provvisti di morsetto di terra.

- L’installazione deve essere fatta utilizzando dispositivi di sicurezza e di comandi
conformi alla EN 12978 e EN12453.

- Le forze di impatto possono essere ridotte mediante l’utilizzo di bordi deformabili.

- Nel caso in cui le forze di impatto superino i valori previsti dalle norme, applicare
dispositivi elettrosensibili o sensibili alla pressione.

- Applicare tutti i dispositivi di sicurezza (fotocellule, coste sensibili, ecc.) necessari
a proteggere l’area da pericoli di impatto, schiacciamento, convogliamento,
cesoiamento. Tenere in considerazione le normative e le direttive in vigore,
i criteri della Buona Tecnica, l’utilizzo, l’ambiente di installazione, la logica di
funzionamento del sistema e le forze sviluppate dall’automazione.

- Applicare i segnali previsti dalle normative vigenti per individuare le zone
pericolose (i rischi residui). Ogni installazione deve essere identicata in modo
visibile secondo quanto prescritto dalla EN13241-1.

- Successivamente al completamento dell’installazione, applicare una targa
identicativa della porta/cancello

- Questo prodotto non può essere installato su ante che incorporano delle porte
(a meno che il motore sia azionabile esclusivamente a porta chiusa).

- Se l’automazione è installata ad una altezza inferiore a 2,5 m o se è accessibile,
è necessario garantire un adeguato grado di protezione delle parti elettriche e
meccaniche.

- Solo per automazioni per serrande

1) Le parti in movimento del motore devono essere installate ad una altezza
superiore a 2,5m al di sopra del pavimento o al di sopra di un altro livello che
possa consentirne l’accesso.

2) Il motoriduttore deve essere installato in uno spazio segregato e provvisto di
protezione in modo che sia accessibile solo con uso di utensili.

- Installare qualsiasi comando sso in posizione tale da non causare pericoli e
lontano da parti mobili. In particolare i comandi a uomo presente devono essere
posizionati in vista diretta della parte guidata, e, a meno che non siano a chiave,
devono essere installati a una altezza minima di 1,5 m e in modo tale da non
essere accessibili al pubblico.

- Applicare almeno un dispositivo di segnalazione luminosa (lampeggiante) in
posizione visibile, ssare inoltre alla struttura un cartello di Attenzione.

- Fissare in modo permanente una etichetta relativa al funzionamento dello sblocco
manuale dell’automazione e apporla vicino all’organo di manovra.

- Assicurarsi che durante la manovra siano evitati o protetti i rischi meccanici ed
in particolare l’impatto, lo schiacciamento, il convogliamento, il cesoiamento tra
parte guidata e parti circostanti.

- Dopo aver eseguito l’installazione, assicurarsi che il settaggio dell’automazione
motore sia correttamente impostato e che i sistemi di protezione e di sblocco
funzionino correttamente.

- Usare esclusivamente parti originali per qualsiasi manutenzione o riparazione.

La Ditta declina ogni responsabilità ai ni della sicurezza e del buon funziona-

mento dell’automazione se vengono impiegati componenti di altri produttori.

- Non eseguire alcuna modica ai componenti dell’automazione se non espres-
samente autorizzata dalla Ditta.

- Istruire l’utilizzatore dell’impianto per quanto riguarda gli eventuali rischi residui,
i sistemi di comando applicati e l’esecuzione della manovra apertura manuale
in caso di emergenza: consegnare il manuale d’uso all’utilizzatore nale.

- Smaltire i materiali di imballo (plastica, cartone, polistirolo, ecc.) secondo quanto
previsto dalle norme vigenti. Non lasciare buste di nylon e polistirolo alla portata
dei bambini.

COLLEGAMENTI
ATTENZIONE! Per il collegamento alla rete utilizzare: cavo multipolare di sezione

minima 5x1,5mm2 o 4x1,5mm2 per alimentazioni trifase oppure 3x1,5mm2 per
alimentazioni monofase (a titolo di esempio, il cavo può essere del tipo H05RN-F
con sezione 4x1.5mm2). Per il collegamento degli ausiliari utilizzare conduttori
con sezione minima di 0,5 mm2.

- Utilizzare esclusivamente pulsanti con portata non inferiore a 10A-250V.

- I conduttori devono essere vincolati da un ssaggio supplementare in prossi-
mità dei morsetti (per esempio mediante fascette) al ne di tenere nettamente
separate le parti in tensione dalle parti in bassissima tensione di sicurezza.

-

Il cavo di alimentazione, durante l’installazione, deve essere sguainato in modo da
permettere il collegamento del conduttore di terra all’appropriato morsetto lasciando
però i conduttori attivi il più corti possibile. Il conduttore di terra deve essere l’ultimo
a tendersi in caso di allentamento del dispositivo di ssaggio del cavo.

ATTENZIONE! i conduttori a bassissima tensione di sicurezza devono essere
sicamente separati dai conduttori a bassa tensione.
L’accessibilità alle parti in tensione deve essere possibile esclusivamente per il
personale qualicato (installatore professionale)

VERIFICA DELL’AUTOMAZIONE E MANUTENZIONE

Prima di rendere denitivamente operativa l’automazione, e durante gli interventi
di manutenzione, controllare scrupolosamente quanto segue:

- Vericare che tutti i componenti siano ssati saldamente;

- Vericare l’operazione di avvio e fermata nel caso di comando manuale.

- Vericare la logica di funzionamento normale o personalizzata.

-

Solo per cancelli scorrevoli: vericare il corretto ingranamento cremagliera -
pignone con un gioco di 2 mm lungo tutta la cremagliera; tenere la rotaia di
scorrimento sempre pulita e libera da detriti.

-Solo per cancelli e porte scorrevoli: vericare che il binario di scorrimento del
cancello sia lineare, orizzontale e le ruote siano idonee a sopportare il peso del
cancello.

-Solo per cancelli scorrevoli sospesi (Cantilever): vericare che non ci sia abbas-
samento o oscillazione durante la manovra.

-Solo per cancelli a battente: vericare che l’asse di rotazione delle ante sia
perfettamente verticale.

- Solo per barriere: prima di aprire la portina la molla deve essere scarica

(asta verticale).

- Controllare il corretto funzionamento di tutti i dispositivi di sicurezza (fotocellule,
coste sensibili, ecc) e la corretta regolazione della sicurezza antischiacciamento
vericando che il valore della forza d’impatto misurato nei punti previsti dalla
norma EN 12445, sia inferiore a quanto indicato nella norma EN 12453.

- Le forze di impatto possono essere ridotte mediante l’utilizzo di bordi deformabili.

- Vericare la funzionalità della manovra di emergenza ove presente.

- Vericare l’operazione di apertura e chiusura con i dispositivi di comando applicati.

- Vericare l’integrità delle connessioni elettriche e dei cablaggi, in particolare lo
stato delle guaine isolanti e dei pressa cavi.

- Durante la manutenzione eseguire la pulizia delle ottiche delle fotocellule.

- Per il periodo di fuori servizio dell’automazione, attivare lo sblocco di emergenza
(vedi paragrafo “MANOVRA DI EMERGENZA”) in modo da rendere folle la parte
guidata e permettere così l’ apertura e la chiusura manuale del cancello.

- Se il cavo di alimentazione è danneggiato, esso deve essere sostituito dal co-
struttore o dal suo servizio di assistenza tecnica o comunque da una persona
con qualica similare, in modo da prevenire ogni rischio.

- Se si si installano dispositivi di tipo “D” (come deniti dalla EN12453), collegati
in modalità non vericata, prescrivere una manutenzione obbligatoria con
frequenza almeno semestrale.

- La manutenzione come sopra descritta deve essere ripetuta con frequenza
almeno annuale o ad intervalli di tempo minori qualora le caratteristiche del
sito o dell’installazione lo richiedessero.

ATTENZIONE!
Ricordarsi che la motorizzazione è una facilitazione dell’uso del cancello/porta e non
risolve problemi a difetti e decienze di installazione o di mancata manutenzione.

DEMOLIZIONE

L’eliminazione dei materiali va fatta rispettando le norme vigenti. Non

gettate il vostro apparecchio scartato, le pile o le batterie usate nei
riuti domestici. Avete la responsabilità di restituire tutti i vostri riuti
da apparecchiature elettriche o elettroniche lasciandoli in un punto di
raccolta dedicato al loro riciclo.

SMANTELLAMENTO

Nel caso l’automazione venga smontata per essere poi rimontata in altro sito bisogna:

- Togliere l’alimentazione e scollegare tutto l’impianto elettrico.

- Togliere l’attuatore dalla base di ssaggio.

- Smontare tutti i componenti dell’installazione.

- Nel caso alcuni componenti non possano essere rimossi o risultino danneggiati,
provvedere alla loro sostituzione.

LE DICHIARAZIONI DI CONFORMITÀ SONO CONSULTABILI NEL SITO WEB:
http://www.bft-automation.com/CE
LE ISTRUZIONI DI MONTAGGIO ED USO SONO CONSULTABILI NELLA SEZIONE
DOWNLOAD.

D811766_16

D812774 00100_06

10 - EOS 1200 U

INSTALLER WARNINGS

Anything that is not explicitly provided for in the installation ma­nual is not allowed. The operator’s proper operation can only be
guaranteed if the information given is complied with. The Firm shall
not be answerable for damage caused by failure to comply with the
instructions featured herein.
While we will not alter the product’s essential features, the Firm reserves
the right, at any time, to make those changes deemed opportune to
improve the product from a technical, design or commercial point of
view, and will not be required to update this publication accordingly.

WARNING! Important safety instructions. Carefully read and comply with
all the warnings and instructions that come with the product as incorrect
installation can cause injury to people and animals and damage to property.
The warnings and instructions give important information regarding safety,
installation, use and maintenance. Keep hold of instructions so that you can
attach them to the technical le and keep them handy for future reference.

GENERAL SAFETY

This product has been designed and built solely for the purpose indicated herein.
Uses other than those indicated herein might cause damage to the product and
create a hazard.

- The units making up the machine and its installation must meet the requirements
of the following European Directives, where applicable: 2014/30/EC, 2014/35/
EC, 2006/42/EC, 2011/305/EC, 99/05/EC and later amendments. For all countries
outside the EEC, it is advisable to comply with the standards mentioned, in ad­dition to any national standards in force, to achieve a good level of safety.

- The Manufacturer of this product (hereinafter referred to as the “Firm”) disclaims
all responsibility resulting from improper use or any use other than that for
which the product has been designed, as indicated herein, as well as for failure
to apply Good Practice in the construction of entry systems (doors, gates, etc.)
and for deformation that could occur during use.

- Installation must be carried out by qualied personnel (professional installer,
according to EN 12635), in compliance with Good Practice and current code.

- Before installing the product, make all structural changes required to produce
safety gaps and to provide protection from or isolate all crushing, shearing and
dragging hazard areas and danger zones in general in accordance with the
provisions of standards EN 12604 and 12453 or any local installation standards.
Check that the existing structure meets the necessary strength and stability
requirements.

- Before commencing installation, check the product for damage.

- The Firm is not responsible for failure to apply Good Practice in the construction
and maintenance of the doors, gates, etc. to be motorized, or for deformation
that might occur during use.

- Make sure the stated temperature range is compatible with the site in which the
automated system is due to be installed.

- Do not install this product in an explosive atmosphere: the presence of ammable
fumes or gas constitutes a serious safety hazard.

- Disconnect the electricity supply before performing any work on the system.
Also disconnect buer batteries, if any are connected.

- Before connecting the power supply, make sure the product’s ratings match the
mains ratings and that a suitable residual current circuit breaker and overcurrent
protection device have been installed upline from the electrical system. Have
the automated system’s mains power supply tted with a switch or omnipolar
thermal-magnetic circuit breaker with a contact separation that provide full
disconnection under overvoltage category III conditions.

- Make sure that upline from the mains power supply there is a residual current
circuit breaker that trips at no more than 0.03A as well as any other equipment
required by code.

- Make sure the earth system has been installed correctly: earth all the metal parts
belonging to the entry system (doors, gates, etc.) and all parts of the system
featuring an earth terminal.

- Installation must be carried out using safety devices and controls that meet
standards EN 12978 and EN 12453.

- Impact forces can be reduced by using deformable edges.

- In the event impact forces exceed the values laid down by the relevant standards,
apply electro-sensitive or pressure-sensitive devices.

- Apply all safety devices (photocells, safety edges, etc.) required to keep the
area free of impact, crushing, dragging and shearing hazards. Bear in mind the
standards and directives in force, Good Practice criteria, intended use, the instal­lation environment, the operating logic of the system and forces generated by
the automated system.

- Apply all signs required by current code to identify hazardous areas (residual
risks). All installations must be visibly identied in compliance with the provisions
of standard EN 13241-1.

- Once installation is complete, apply a nameplate featuring the door/gate’s data.

- This product cannot be installed on leaves incorporating doors (unless the motor
can be activated only when the door is closed).

- If the automated system is installed at a height of less than 2.5 m or is accessible,
the electrical and mechanical parts must be suitably protected.

- For roller shutter automation only

1) The motor’s moving parts must be installed at a height greater than 2.5 m
above the oor or other surface from which they may be reached.

2) The gearmotor must be installed in a segregated and suitably protected space
so that it cannot be reached without the aid of tools.

- Install any xed controls in a position where they will not cause a hazard, away
from moving parts. More specically, hold-to-run controls must be positioned
within direct sight of the part being controlled and, unless they are key operated,
must be installed at a height of at least 1.5 m and in a place where they cannot
be reached by the public.

- Apply at least one warning light (ashing light) in a visible position, and also
attach a Warning sign to the structure.

- Attach a label near the operating device, in a permanent fashion, with informa­tion on how to operate the automated system’s manual release.

- Make sure that, during operation, mechanical risks are avoided or relevant
protective measures taken and, more specically, that nothing can be banged,
crushed, caught or cut between the part being operated and surrounding parts.

- Once installation is complete, make sure the motor automation settings are
correct and that the safety and release systems are working properly.

- Only use original spare parts for any maintenance or repair work. The Firm dis­claims all responsibility for the correct operation and safety of the automated
system if parts from other manufacturers are used.

- Do not make any modications to the automated system’s components unless
explicitly authorized by the Firm.

- Instruct the system’s user on what residual risks may be encountered, on the
control systems that have been applied and on how to open the system manu­ally in an emergency. give the user guide to the end user.

- Dispose of packaging materials (plastic, cardboard, polystyrene, etc.) in accord­ance with the provisions of the laws in force. Keep nylon bags and polystyrene
out of reach of children.

WIRING
WARNING! For connection to the mains power supply, use: a multicore cable with

a cross-sectional area of at least 5x1.5mm

2

or 4x1.5mm2 when dealing with three­phase power supplies or 3x1.5mm2 for single-phase supplies (by way of example,
type H05RN-F cable can be used with a cross-sectional area of 4x1.5mm2). To con­nect auxiliary equipment, use wires with a cross-sectional area of at least 0.5 mm2.

- Only use pushbuttons with a capacity of 10A-250V or more.

- Wires must be secured with additional fastening near the terminals (for example,

using cable clamps) in order to keep live parts well separated from safety extra
low voltage parts.

- During installation, the power cable must be stripped to allow the earth wire

to be connected to the relevant terminal, while leaving the live wires as short
as possible. The earth wire must be the last to be pulled taut in the event the
cable’s fastening device comes loose.

WARNING! safety extra low voltage wires must be kept physically separate from
low voltage wires.
Only qualied personnel (professional installer) should be allowed to access
live parts.

CHECKING THE AUTOMATED SYSTEM AND MAINTENANCE

Before the automated system is nally put into operation, and during maintenance
work, perform the following checks meticulously:

- Make sure all components are fastened securely.

- Check starting and stopping operations in the case of manual control.

- Check the logic for normal or personalized operation.

- For sliding gates only: check that the rack and pinion mesh correctly with 2 mm

of play along the full length of the rack; keep the track the gate slides on clean
and free of debris at all times.

- For sliding gates and doors only: make sure the gate’s running track is straight

and horizontal and that the wheels are strong enough to take the weight of the
gate.

- For cantilever sliding gates only: make sure there is no dipping or swinging

during operation.

- For swing gates only: make sure the leaves’ axis of rotation is perfectly vertical.

-For barriers only: before opening the door, the spring must be decompressed

(vertical boom).

- Check that all safety devices (photocells, safety edges, etc.) are working properly

and that the anti-crush safety device is set correctly, making sure that the force
of impact measured at the points provided for by standard EN 12445 is lower
than the value laid down by standard EN 12453.

- Impact forces can be reduced by using deformable edges.

- Make sure that the emergency operation works, where this feature is provided.

- Check opening and closing operations with the control devices applied.

- Check that electrical connections and cabling are intact, making extra sure that

insulating sheaths and cable glands are undamaged.

- While performing maintenance, clean the photocells’ optics.

- When the automated system is out of service for any length of time, activate the

emergency release (see “EMERGENCY OPERATION” section) so that the operated
part is made idle, thus allowing the gate to be opened and closed manually.

-

If the power cord is damaged, it must be replaced by the manufacturer or their
technical assistance department or other such qualied person to avoid any risk .

- If “D” type devices are installed (as dened by EN12453), connect in unveried

mode, foresee mandatory maintenance at least every six months

- The maintenance described above must be repeated at least once yearly or at

shorter intervals where site or installation conditions make this necessary.

WARNING!

Remember that the drive is designed to make the gate/door easier to use and
will not solve problems as a result of defective or poorly performed installation
or lack of maintenance

SCRAPPING

Materials must be disposed of in accordance with the regulations in

force. Do not throw away your discarded equipment or used batteries
with household waste. You are responsible for taking all your waste
electrical and electronic equipment to a suitable recycling centre.

DISMANTLING

If the automated system is being dismantled in order to be reassembled at another
site, you are required to:

- Cut o the power and disconnect the whole electrical system.

- Remove the actuator from the base it is mounted on.

- Remove all the installation’s components.

- See to the replacement of any components that cannot be removed or happen

to be damaged.

DECLARATIONS OF CONFORMITY CAN BE FOUND AT http://www.bft-

automation.com/CE

INSTRUCTIONS FOR USE AND ASSEMBLY CAN BE FOUND IN THE DOWN­LOAD SECTION.

D811766_16

D812774 00100_06

EOS 1200 U - 15

ENGLISH FRANÇAIS ESPAÑOL

NEDERLANDS

DEUTSCHITALIANO

146

253.16

65

3

7

8

35

338

0

-

2

7

8

0

3

7

6

0

-

3

1

6

0

1

2

2

5

0

2,5m min

2,5m min

2,5m min

2,5m min

Lampadina a led di cortesia mod. BFT
BFT model courtesy LED lamp
Lampe de courtoisie à Led modèle BFT
LED-Notbeleuchtung Modell BFT
Lámpara de LED de cortesía mod. BFT
Led voetverlichting model BFT

D812774 00100_06

16 - EOS 1200 U

C

C

D

D

B

A

D

Tassello / Plug / Cheville
Dübel / Taco / Plug.

D812774 00100_06

EOS 1200 U - 17

ENGLISH FRANÇAIS ESPAÑOL

NEDERLANDS

DEUTSCHITALIANO

300 mm

E

C

B

Tassello / Plug / Cheville
Dübel / Taco / Plug.

D

A

C

D

D

A

D812774 00100_06

18 - EOS 1200 U

SAFE1 = 1

SAFE1 = 1

IC 1

IC 2

SAFE 1

FAULT 1

AUX 3 (NO)

SAFE 1

FAULT 1

D812774 00100_06

EOS 1200 U - 19

ENGLISH FRANÇAIS ESPAÑOL

NEDERLANDS

DEUTSCHITALIANO

6

D812774 00100_06

20 - EOS 1200 U

3 1245678910111213

JP7

UP

DOWN

D812774 00100_06

EOS 1200 U - 21

ENGLISH FRANÇAIS ESPAÑOL

NEDERLANDS

DEUTSCHITALIANO

GESLOTEN DEUR.

Fig. 26

Montaggio tappi per operatore EOS 1200 U - Assembly of caps for EOS 1200 U operator - Montage bou­chons pour opérateur EOS 1200 U - Montage der Stopfen für Antrieb EOS 1200 U - Montajie topones para
automatisacio’n EOS 1200 U - Montage doppen voor aandrijving EOS 1200 U.

D812774 00100_06

EOS 1200 U - 29

ENGLISH

OK

Press the OK key

BFT
venere d
0000
0000
00

OK

ACCESS TO MENUS

Control unit software version
No. total manoeuvres

(x 10)
No. manoeuvres since latest
maintenance(x 10)

No. radio control devices
memorised

Fig. A

LEGENDA

[ 00 ]

Parameter increment/reduction
or ON/OFF commutation

Menu scrolling
(+ = preceding - = following)

Press OK key (Enter/confirm)

OK! message (confirms modification made)

PRG

OK

+/-

-

+

/ON
/OFF

KO! message (value or function error)

PRG

“Wait” message (enter value or function)

Simultaneously press the + and - keys.
Simultaneous pressure of the + and – keys
allows you to exit the active menu and return
to the preceding menu; if this takes place at
the main menu level, programming is exited
and the display switched off.
The modifications made are only confirmed if
the OK key is subsequently pressed.

Preset value

OK

8888

End

LOGIC.

FOLLOWING MENUS

FIG. B

dist.sloud

part.open

op.force

cls.force

op speed

cl speed

tca

step-by-step movemnt

pre-alarm

ibl open

safe1

aux3

fixed code

prot.lev

serial mode

address

ic1

ic 2

tca

End

0---

10--

150- 1520 ok

(007)

(040)

(010)

(075)

(075)

(099)

(099)

(000)

(000)

(000)

(000)

(000)

(000)

(000)

(000)

(000)

(000)

(004)

sw mov

(001)

***

*** Password entry.
Request with Protection Level logic
set to 1, 2, 3, 4

D812774 00100_06

30 - EOS 1200 U

Fig. B

PRECEDING MENUS

FIG. A

RADIO

-

+

-

+

+/-

END

OK

+/-

Press P1 (pushbutton) on radio
control device.

Press the required T (key) on
radio control device – see Fig. B2

Press the required T (key) on
radio control device – see Fig. B2

Release P1 on radio
control device

ADD start

hidden button release

desired button

01

PRG.

READ

OK

OK

OK

ERASE 64

-

+

-

+

Press P1 (pushbutton) on radio
control device.

Press the required T (key) on
radio control device – see Fig. B2

Release P1 on radio
control device

ADD 2ch hidden button release

desired button

01

OK

-

+

01 t1

COD RX

OK

1A9C

OK

22FD

OK

01

OK

-

+

+/-

o

language

END

END

END

END

l.sw adj

vk

T3T4

T1

T1 T2

T2

password

0---

10--

150- 1520 prg

END

D812774 00100_06

EOS 1200 U - 31

ENGLISH

INSTALLATION MANUAL

1) GENERAL OUTLINE

The EOS 1200 U system is suitable for motorising sectional doors (g. 3), protrud­ing fully retracting spring-operated overhead doors (g. 2) and counterweight
overhead doors provided with an appropriate towing arm (g. 4). The overhead
door must not be higher than 3 metres. Its easy installation allows fast tting
without needing the door to be modied. The irreversible gearmotor keeps the
door locked in the closing position.
For structures with a pedestrian door, ensure installing a safety mechanical
interlock (Fig. 3A)
The supply cable provided is suitable only for indoor use.

2) TECHNICAL SPECIFICATIONS

2.1) Actuator

Power supply:..................................................................................220 - 230V~ 50/60Hz (*)

Motor voltage:.................................................................................................................24V

Max. power absorbed from mains:..............................................................................240W

Lubrication:.................................................................................................permanent grease

Towing and pushing force:............................................................................................1200N

Working stroke:....................................TRACK L.=2900 working stroke=2400 mm(**)

..................................................................TRACK L.=3500 working stroke=3000 mm(***)

Average speed:...........................................................................................................4,5 m/min

Impact reaction:..........................................integrated torque limiter on control panel

Manoeuvres in 24 hours:.....................................................................................................100

Limit switch:..................................................................................Electronic with ENCODER

Courtesy light: ....................................................................BFT model courtesy LED lamp

Working temperature:.......................................................................................-15°C / +50°C

Degree of protection:..........................................................................................................IPX0

Motor head weight:..............................................................................................................5 kg

Sound pressure:............................................................................................................<70dB(A)

Dimensions:.....................................................................................................................see g.1

(*) Available in all mains voltages.
(**)By turning the motor head by 90° (Fig.11) the useful stroke will be 2580 mm.
(***)By turning the motor head by 90° (Fig.11) the useful stroke will be 3180 mm.

3) ACTUATOR INSTALLATION

3.1) Preliminary checks

• Checkthatthedoorisbalanced.

• Checkthatthedoorslidessmoothlyalongitsentiretravel.

• Ifthedoorhasnotbeennewlyinstalled,checkthewearconditionofallits

components.

• Repairorreplacefaultyorwornparts.

• Theautomationreliabilityandsafetyaredirectly inuencedbythestateof

the door structure.

• Beforettingthemotor,removeanysuperuousropesorchainsanddisable

any unnecessary appliances.

• Theguidedpartmustbettedwithasafetyfallprotectionsystem.

3.2) FITTING

After unpacking, dispose of the parts which make up the package properly, by
separating the dierent type of materials (cardboard, polystyrene, PVC,
etc.) according to the national rules in force.

1) Remove the existing locking bolt from the cremone bolt of the door.

2) Fit the metal wall bracket to the track-holder bracket using the screws sup­plied as standard (Fig.12 Ref.E). The screws must not be tightened, so that
the bracket can be rotated.

3) In order for the track to be correctly xed, mark the mid-point of the door,
position the BIN onto the ceiling and mark the holes (Fig.6).

Make sure that the distance between the track and the door panel is com-

prised between 108 and 166 mm (see Fig.14). If this is not the case, use the
brackets provided (Fig.10). If the distance is smaller, the towing plate must
be shortened.

4) Drill the ceiling using a D.10 bit, with reference to the markings made previ­ously, and insert the plugs.

5) With the help of an adequate support, lift the entire motor, screw the screws
onto the track-holding bracket without xing them to the door frame
(Fig.9A) or, if the height allows it, t the bracket to the masonry lintel by
means of plugs (Fig.9B).

6) Rest the motor onto the oor (takingcarenottodamage it) and x the

articulated bracket to the door frame or to the ceiling (Fig.9A, Fig.9B).

7) Lift the motor-driven head until everything rests against the ceiling and in­sert the xing screws which lock the track.

8) In the case where the motor is not directly xed to the ceiling, t the brack­ets as shown in Fig.10 Ref.C, after marking and drilling the holes with refer­ence to the brackets.

9) In the case where the track is made in two halves, see Fig.13; for the dier­ent types of xing methods, see the previous gures.

10) Release the carriage and x the anchoring brackets to the door panel (Fig.14).
The distance allowed between track and sectional door is 108 to 166 mm.
In case of greater distance, it is necessary to use the brackets and lower the
motor; in case of shorter distance, it is necessary to shorten the towing plate.

11)

Check that the carriage and anchoring bracket screws provide for correct
play of the towing bar.

12)

Stick the adhesive labels supplied next to the dangerous points (Fig. 5).

4) CHAIN TIGHTENER ADJUSTMENT (EOS 1200 U)

The operator supplied is already calibrated and inspected. Should the chain ten­sion need to be adjusted, proceed as shown in g. 15.

WARNING: the anti-tear spring element must never be completely com­pressed. Scrupulously check that the spring does not become totally com­pressed during operation.

4.1) MANUAL RELEASE (See USER GUIDE -FIG.1-).

4.2) REMPLACEMENT DE L’AMPOULE (FIG.5)

5) ELECTRICAL INSTALLATION SET-UP (Fig.16)

M) Actuator
Ft) Transmitter photocell
Fr) Receiver photocells

T) 1-2-4 channel transmitter.

Arrange for the connections of accessories and safety and control devices to
reach the motor unit, keeping the mains voltage connections clearly separate
from the extra low safety voltage connections (24V) by means of the appropriate
cable holder (g. 8 ref. 5P1).
Proceed to connection following the indications given in the wiring diagram.
The cables for connecting the accessories must be protected by a raceway (fig. 8 ref. 5C1).

6) VENERE D Control panel (Fig.17)

Supply to accessories: ...........................................................................24V~ (180mA max)

........................................................................................24V~ Vsafe VENERE D (180mA max)

Torque limiter setting:..................................................................on closing and opening

Automatic closing time:..................................................................................from 1 to 180s

Blinker connection:.........................................................................................24V~ max 25W

Service light switching-on time:........................................................................................90s

Incorporated rolling-code radio receiver:................................frequency 433.92 MHz

Coding:.................................................................................................rolling-code algorithm

No. combinations:.......................................................................................................4 milliard

Antenna impedance:.......................................................................................50Ohm (RG58)

Max no. radio controls to be memorised:........................................................................10

Fuses:........................................................................................................................see gure 17

6.1) Terminal board connections (Fig.17)
WARNINGS - For wiring and installation operations, refer to the current
standards and good technical principles.

The wires supplied with extra low safety voltage (24V) must be kept physically
separate from the low voltage wires, or else they must be provided with adequate
additional insulation of at least 1mm.
The wires must be clamped by an extra fastener near the terminals, for example
by bands.

TERMINAL DESCRIPTION

JP2 transformer wiring

JP10 motor wiring

1-2

Antenna input for integrated radio-receiver board
(1: BRAID. 2: SIGNAL)

3-4 IC1 input (N.O.)
3-5 STOP input (N.C.) If not used, leave the jumper inserted.

3-6

SAFE1 input (N.C.) If not used, leave the jumper inserted.

3-7

FAULT 1 input (N.O.)
Input for photocells provided with checking N.O. contact

8-9 24 V~ output for blinking light (25 W max)

10-11

24V~ 180mA max output – power supply for photocells or
other devices

12-13

24V~ Vsafe 180mA max output – power supply for checking
photocell transmitters.

14-15 AUX3 outupt ( N.O.)/

2nd Radio Channel

16-17 IC2 input

7) PROGRAMMING

The control panel with built-in microprocessor comes with factory settings, which
are valid for standard installations. The preset parameters can only be edited
using the built-in programmer with display or universal handheld programmer.
If you are performing programming via a universal handheld programmer, care­fully read the relevant instructions for use of the universal handheld programmer
before proceeding as follows. Connect the universal handheld programmer
to the control unit by means of the UNIFLAT accessory. Enter the “CONTROL
UNITS” menu, then the “PARAMETERS” submenu and use the up/down arrows
to run through the screens on the display, entering the numerical values of the
parameters listed below.
For information on operating logics, refer to the “LOGIC” submenu.
If you are performing programming with the aid of the built-in programmer, refer
to Fig. A and B and to the “setup” section.
The meaning of each parameter and the values each can be given are listed below.

7.1) Setup

Via the programmer with display, you can set all the VENERE D control panel’s
functions.
The programmer has three buttons for navigating between menus and setting
operating parameters:
+ menu scroll/increase value key

- menu scroll/decrease value key
OK return key (conrm).
Pressing the + and - keys at the same time allows you to exit the menu you are
working inside and move to the next menu up. If the + and - keys are pressed
at the same time when on the main menus (parameters-logic-radio-language­default-autoset- limit switch adjustment), you exit programming and the display
switches o (the END message appears).
Changes only become operative if the OK key is pressed after they are made. The
rst time you press the OK key, you enter programming mode.
To start with, the display gives the following information:

- Software version of control unit

- Total number of operations carried out (the value is given in thousands, hence
the display will keep showing 0000 for the rst thousand operations)

-

Number of operations carried out since last service (the value is given in thousands,
hence the display will keep showing 0000 for the rst thousand operations)

- Number of memorized remote controls.

Pressing the OK key during the initial presentation allows you to skip to the rst
menu (parameters-logic-radio-language-default-autoset-limit switch adjustment).
The main menus are listed below along with the relevant submenus available for each.
The default setting is the one inside square brackets [ 0 ]

D812774 00100_06

32 - EOS 1200 U

INSTALLATION MANUAL

The message that appears on the display is shown inside round brackets.
Refer to Figures A and B for the control unit setup procedure.

7.2) PARAMETERS MENU PARA  PARAMETERS TABLE “A”

7.3) LOGIC MENU LOGIC LOGIC TABLE “B”

7.4) RADIO MENU radio RADIO TABLE “C”

The Clonix built-in on-board receiver also has a number of important advanced features:

• Cloningofmastertransmitter(rollingcodeorxedcode).

• Cloningtoreplacetransmittersalreadyenteredinreceiver.

• Transmitterdatabasemanagement.

• Receivercommunitymanagement.

To use these advanced features, refer to the universal handheld programmer’s
instructions and to the general receiver programming guide.

Consult sections 7/8/9 for further information on the built-in Clonix receiv­er’s advanced features.

7.5 LANGUAGE MENU LANGUAGE

Used to set the programmer’s language on the display.
There are 5 language options:

- ITALIAN (ITA)

- FRENCH (FRA)

- GERMAN (DEU)

- ENGLISH (ENG)

- SPANISH (ESP)

7.6) DEFAULT MENU (DEFAULT)

Restores the controller’s default factory settings. Following this reset, you will
need to run the autoset function again.

7.7) DIAGNOSTICS AND MONITORING

The display on the VENERE D panel gives a certain amount of useful information
both during normal operation and when faults are detected.

Diagnostics:

In the event of malfunctions, the display gives a message showing which device
needs checking:
STRE = START E input activated
STRI = START I nput activated
STOP = STOP input activated
PHOT = PHOT input activated
SWO = OPENING LIMIT SWITCH input activated
SWC = CLOSING LIMIT SWITCH input activated
PED = PEDESTRIAN input activated
OPEN = OPEN input activated
CLS = CLOSE input activated

In the event the door encounters an obstacle, the VENERE D panel stops the door
and commands it to reverse, while on the display the “AMP” message appears

Monitoring:

During opening and closing, the display shows four numbers separated by a
decimal point, e.g. 35.40. The numbers are updated constantly during the door’s
operation and stand for the instantaneous torque reached by motor 1 (35) and
torque threshold (opening, closing, slow-down) set in the parameters menu (40).
Via these values, we can correct the torque setting.
If the value of the instantaneous torque reached during the door’s operation gets
rather close to the threshold value set in the parameters menu, malfunctioning
may occur in the future due to wear or the door becoming slightly misshapen.
Consequently, it is advisable to check the maximum torque reached during a
number of cycles at the installation stage and, where necessary, set a value ap­prox. 5/10 percentage points higher in the parameters menu.

7.8) ERROR DIAGNOSTICS:
ER01 Error in safety device (photocell) test
ER03 Error in safety device (photocells active only on opening)

test
ER04 Error in safety device (photocells active only on closing)
test

ER10 Problems detected in motor’s control circuit
ER11 Problems detected in motor’s current reading circuit

7.9) AUTOSET MENU
Move the door to the closed position

• LaunchanautosetoperationbygoingtotherelevantmenuontheVENERE

D panel (Fig.B).

• AssoonasyoupresstheOKbutton,the“............”messageisdisplayedandthe

control unit commands the door to perform a full cycle (opening followed
by closing), during which the minimum torque value required for the door
to move is set automatically.

During this stage, it is important to avoid breaking the photocells’ beams and

not to use the START and STOP commands or the display.

Once this operation is complete, the control unit will have automatically set

the optimum torque values. Check them and, where necessary, edit them as
described in the programming section.

WARNING: Check that the force of impact measured at the points

provided for by standard EN 12445 is lower than the value laid down
by standard EN 12453.

Warning!! While the autoset function is running, the obstacle detection

function is not active. Consequently, the installer must

7.10) LIMIT SWITCH ADJUSTMENT MENU

The VENERE D control panel has an opening and closing limit switch adjustment
menu, which simplies the installation procedure.
Refer to Figures 18/19 and Fig.B illustrating the control panel’s programming
and proceed as follows:

• Launchalimitswitchadjustmentoperationbygoingtotherelevantmenu

on the VENERE D panel (Fig.B).

• Whenthe“CLOSE”messageisdisplayed,movethedoortothedesiredclosed

position using the “UP” and “DOWN” buttons on the control unit, bearing in

mind that the “DOWN” button closes the door, while the “UP” button opens
the door. As soon as the door is in the desired closed position, press the “OK”
button to store the closed travel limit position.

• Whenthe“OPEN”messageisdisplayed,movethedoortothedesiredopen

position using the “UP” and “DOWN” buttons on the control unit, bearing in
mind that the “DOWN” button closes the door, while the “UP” button opens
the door.

As soon as the door is in the desired open position, press the “OK” button to

store the open travel limit position.

• Positionthe“runnerstop”correctlyupagainsttherunnerandsecureinplace

with the screws (g.18 ref.6 A-B).

NOTE: These operations must be performed in “deadman” mode at reduced

speed and without the safety devices operating.

7.11) STATISTICS

Connect the UNIVERSAL HANDHELD programmer to the control unit, enter the
CONTROL UNIT/STATISTICS menu and run through the statistics parameters screen:

- Software version of card microprocessor.

- Number of cycles performed. If the motors are replaced, write down the
number of operations performed so far.

- Number of c ycles performed since last service. Automatically reset every time
self-diagnosis is run or parameters are written.

- Date of last service. Must be updated manually via the relevant “Update service
date” menu

.- System description. Allows for 16 characters to be entered to identify the

system.

7.12) PASSWORD MENU (PASSWORD)

Used to set a password for the board’s wireless programming via the U-link network.
With “PROTECTION LEVEL” logic set to 1,2,3,4, the password is required to access
the programming menus. After 10 consecutive failed attempts to log in, you will
need to wait 3 minutes before trying again. During this time, whenever an at­tempt is made to log in, the display will read “BLOC”. The default password is 1234.

7.13

) U-LINK OPTIONAL MODULES

Refer to the U-link instructions for the modules.

8) TECHNICAL DATA OF BUILT-IN RECEIVER

Receiver’s output channels:

- output channel 1, if activated, commands the door to START

- output channel 2, if activated, commands the 2nd radio channel relay to
energize for 1 sec..

Usable transmitter versions:

All ROLLING CODE transmitters compatible with

8.1) INSTALLING THE ANTENNA

Use an antenna tuned to 433MHz.
Use RG58 coax cable to connect the Antenna and Receiver.

Metal bodies close to the antenna can interfere with radio reception. If the trans­mitter’s range is limited, move the antenna to a more suitable position.

8.2) MANUAL TRANSMITTER PROGRAMMING

In the case of standard installations in which advanced features are not required,
transmitters can be memorized manually, referring to Fig.B for the basic pro­gramming.

-

If you want the transmitter to activate output 1 (START ) with key 1 or key 2 or
key 3 or key 4, enter the transmitter in the start key menu as illustrated in Fig.B.

- If you want the transmitter to activate output 2 (2nd radio channel relay) with
key 1 or key 2 or key 3 or key 4, enter the transmitter in the 2ch key menu as
illustrated in Fig.B.

Note: The hidden key P1 changes appearance depending on the transmitter

model. For transmitters featuring a hidden key, press the hidden button P1
(Fig.B1).

For transmitters with no hidden key, simultaneously pressing the transmitter’s

4 keys, or opening the battery compartment and using a screwdriver to jump
the two P1 points (Fig.B2), is equivalent to pressing key P1.

IMPORTANT NOTE: THE FIRST TRANSMITTER MEMORIZED MUST BE IDENTI­FIED BY ATTACHING THE KEY LABEL (MASTER).

In the event of manual programming, the rst transmitter assigns the RECEIVER’S
KEY CODE: this code is required to subsequently clone the radio transmitters.

8.3) REMOTE TRANSMITTER PROGRAMMING (Fig.20)

1) Press the hidden key (P1) of a transmitter that has already been memorized
in standard mode via manual programming.

2) Press the normal key (T1-T2-T3-T4) of a transmitter that has already been
memorized in standard mode via manual programming.

3) Thecourtesylightashes.Presswithin10sec.thehiddenkey(P1)ofatrans­mitter to be memorized.

4) The courtesy light remains steadily lit. Press the normal key (T1-T2-T3-T4) of
a transmitter to be memorized.

The receiver exits programming mode after 10 sec.: you can use this time to enter
other new transmitters.
This mode does not require access to the control panel.

9) EMERGENCY MANOEUVRE

In case of electric power failure or system malfunction, the manoeuvre must be
carried out manually by pulling the wire connected to the carriage, as in g.21.
For garages which are not provided with a second exit, it is compulsory to t an
external key release device like Mod. SM1 (g.22) or Mod. SET/S (g.23).

10) AUTOMATION CHECK

Before the automation device nally becomes operational, scrupulously
check the following conditions:

• Checkthatallthesafetydevices(limitmicroswitches,photocells,electricedges

etc) operate correctly.

• Checkthatthedoor(antisquash)thrustiscomprisedwithinthelimitssetout

by the current standards, and anyway not too strong for the installation and
operating conditions.

• Checkthatthechain-tighteningspringelementisnotcompletelycompressed

D812774 00100_06

EOS 1200 U - 33

ENGLISH

INSTALLATION MANUAL

during the manoeuvre.

• Checkthemanualopeningcontroloperation.

•

Check the opening and closing operations using the control devices tted.

• Checkthenormalandcustomisedoperationelectroniclogics.

11) AUTOMATION DEVICE USE

- Since the automation device can be remotely controlled by means of a radio
control device or a Start button, and therefore when not in sight, all the safety

devicesmustbefrequentlycheckedinordertoensuretheirperfecteciency.

In the event of any malfunction, request immediate assistance from qualied
personnel. Children must be kept at a safe distance from the automation opera­tion area.

- Partial or pedestrian opening is to be treated as an operation to be performed
only occasionally and no more than 5 such operations should be performed in
a row if the automated system is to work properly.

12) AUTOMATION CONTROL

The use of this control device allows the gate to be opened and closed automati­cally. There are dierent types of controls (manual, radio control, magnetic card
access etc.) depending on the installation requirements and characteristics. For
the various control systems, see the relevant instructions. The automation device
users must be instructed on control and operation.

13) ACCESSORIES

SM1 External release device to be applied to the cremone bolt already tted

to the overhead door (g.22).

SET/S External release device with retracting handle for sectional doors mea-

suring max 50mm (g.23).

ST Automatic bolt release device for spring-operated overhead doors. Fitted

to the control arm, it automatically releases the side door bolts (g.24).

14) MAINTENANCE

Before carrying out any maintenance operation, disconnect the system power
supply.

• Periodicallycheckthetensionofthechain/belt(twiceayear).

• Occasionallycleanthephotocellopticalelements,ifinstalled.

• Haveaqualiedtechnician(installer)checkthecorrectsettingoftheelectronic

clutch.

• Whenany operational malfunction if found, and not resolved,disconnect

the system power supply and request the assistance of a qualied technician
(installer). When the product is out of service, activate the manual release
device to allow the door to be opened and closed manually.

If the power supply cable is damaged, it must be replaced directly by our
company or our technical service department or by a technician having

similar qualication so as to avoid any risks.

14.1) FUSE REPLACEMENT (Fig.25)
WARNING! Disconnect the mains voltage.

Remove the rubber protection from the fuse-carrier. Remove the fuse (Fig.25,
Ref.A) to be replaced and replace it with a new one. After completing this opera­tion, re-t the rubber protection.

TABLE “A”  PARAMETERS MENU - PARA



Parameter min. max. Default

Personal

Denition Description

TCA

1 180 40

Automatic clos-

ing time [s]

Waiting time before automatic closing.

CL.DIST.

SLOUD

7 100 7

Slow-down

distance

[cm]

Motor slow-down distance during opening and closing, expressed in cm

WARNING: Once the parameter has been edited, a complete uninterrupted
opening-closing cycle is required.
WARNING: when the display reads “SET”, obstacle detection is not active.

PARTIAL

OPEN

00,1 06,0 01,0

Partial opening

[m]

Partial opening distance following activation of PED pedestrian command. Set the numerical value
of partial opening in the range 10 cm (00,1) to 6 m (06,0)

OP.FORCE

1 99 75

Leaf force

during opening

[%]

Force exerted by leaf during opening. This is the percentage of force delivered, beyond
the force stored during the autoset cycle (and subsequently updated), before an
obstacle alarm is generated.
The parameter is set automatically by the autoset function.

WARNING: It aects impact force directly: make sure that current safety
requirements are met with the set value (*). Install anti-crush safety

devices where necessary (**).

CLS.FORCE

1 99 75

Leaf force

during closing

[%]

Force exerted by leaf during closing. This is the percentage of force delivered, beyond
the force stored during the autoset cycle (and subsequently updated), before an
obstacle alarm is generated.
The parameter is set automatically by the autoset function.

WARNING: It aects impact force directly: make sure that current safety
requirements are met with the set value (*). Install anti-crush safety

devices where necessary (**).

OP SPEED

40 99 99

Opening speed

[%}

Percentage of maximum speed that can be reached by motor during opening.

WARNING: Once the parameter has been edited, a complete uninterrupted
opening-closing cycle is required. WARNING: when the display reads "SET",
obstacle detection is not active.

CL SPEED

40 99 99

Closing speed

[%]

Percentage of maximum speed that can be reached by motor during closing.

WARNING: Once the parameter has been edited, a complete uninterrupted
opening-closing cycle is required. WARNING: when the display reads "SET",
obstacle detection is not active.

(*) In the European Union, apply standard EN 12453 for force limitations, and standard EN 12445 for measuring method.
(**) Impact forces can be reduced by using deformable edges.

D812774 00100_06

34 - EOS 1200 U

INSTALLATION MANUAL

TABLE “B”  LOGIC MENU - logic

Logic Denition

De-

fault

Cross

out

setting

used

Optional extras

TCA

Automatic Clo-

sing Time

0

0 Logic not enabled

1 Switches automatic closing on

STEP-BY-STEP

MOVEMNT

Step-by-step

movement

0

0

Inputs congured as Start E, Start I, Ped
operate with 4-step logic.

step-by-step mov.

3 STEP 4 STEP

CLOSED

OPENS

OPENS

DURING

CLOSING

STOPS

OPEN

CLOSES CLOSES

DURING

OPENING

STOP + TCA

STOP + TCA

AFTER STOP

OPENS OPENS

1

Inputs congured as Start E, Start I, Ped op­erate with 3-step logic. Pulse during closing
reverses movement.

PRE-ALARM

Pre-alarm 0

0 Theashinglightcomesonatthesametimeasthemotor(s)start.

1 Theashinglightcomesonapprox.3secondsbeforethemotor(s)start.

IBL OPEN

Block pulses

during opening

0

0 Pulse from inputs congured as Start E, Start I, Ped has eect during opening.

1 Pulse from inputs congured as Start E, Start I, Ped has no eect during opening.

SAFE 1

Conguration

of safety input

SAFE 1.

0

0 Input congured as Phot (photocell).

1 Input congured as Phot test (tested photocell).

2 Input congured as Phot op (photocell active during opening only).

3 Input congured as Phot op test (tested photocell active during opening only).

4 Input congured as Phot cl (photocell active during closing only).

5 Input congured as Phot cl test (tested photocell active during closing only).

AUX 3

Conguration of

AUX 3 output. 0

0 Output congured as 2nd Radio Channel.

1 Output congured as SCA (gate open light). In this case, the 2nd radio channel controls partial opening.

FIXED CODE

Fixed code 0

0

Receiver is congured for operation in rolling-code mode.
Fixed-Code Clones are not accepted.

1

Receiver is congured for operation in xed-code mode.
Fixed-Code Clones are accepted.

Prot.lev

Setting the

protection level

0

0

A - The password is not required to access the programming menus
B - Enables wireless memorizing of transmitters.
Operations in this mode are carried out near the control panel and do not require access:

- Press in sequence the hidden key and normal key (T1-T2-T3-T4) of a transmitter that has already been
memorized in standard mode via the radio menu.

- Press within 10 sec. the hidden key and normal key (T1-T2-T3-T4) of a transmitter to be memorized.
The receiver exits programming mode after 10 sec.: you can use this time to enter other new transmitters
by repeating the previous step.
C - Enables wireless automatic addition of clones.
Enables clones generated with the universal programmer and programmed Replays to be added to the
receiver’s memory.
D - Enables wireless automatic addition of replays.
Enables programmed Replays to be added to the receiver’s memory.
E - The board’s parameters can be edited via the U-link network

1

A - You are prompted to enter the password to access the programming menus
The default password is 1234.
No change in behaviour of functions B - C - D - E from 0 logic setting

2

A - You are prompted to enter the password to access the programming menus
The default password is 1234.
B - Wireless memorizing of transmitters is disabled.
C - Wireless automatic addition of clones is disabled. No change in behaviour of functions D - E from 0 logic setting

3

A - You are prompted to enter the password to access the programming menus
The default password is 1234.
B - Wireless memorizing of transmitters is disabled.
D - Wireless automatic addition of Replays is disabled.
No change in behaviour of functions C - E from 0 logic setting

4

A - You are prompted to enter the password to access the programming menus
The default password is 1234.
B - Wireless memorizing of transmitters is disabled.
C - Wireless automatic addition of clones is disabled.
D - Wireless automatic addition of Replays is disabled.
E - The option of editing the board’s parameters via the U-link network is disabled.
Transmitters are memorized only using the relevant Radio menu.
IMPORTANT: This high level of security stops unwanted clones from gaining access and also stops radio
interference, if any.

D812774 00100_06

EOS 1200 U - 35

ENGLISH

INSTALLATION MANUAL

Logic Denition

De-

fault

Cross

out

setting

used

Optional extras

SERIAL MODE

Serial mode

(Identies how

board is congured

in a BFT network

connection).

0

0 Standard SLAVE: board receives and communicates commands/diagnostics/etc.

1 Standard MASTER: board sends activation commands (START, OPEN, CLOSE, PED, STOP) to other boards.

ADDRESS

Address 0

[ ___ ]

Identies board address from 0 to 119 in a local BFT network connection.
(see U-LINK OPTIONAL MODULES section)

IC 1

Conguration of

command input

IC 1.

0

0 Input congured as Start E.

1 Input congured as Start I.

2 Input congured as Open.

IC 2

Conguration of

command input

IC 2.

4

3 Input congured as Close.

4 Input congured as Ped.

sw mov

Movement to

limit switch

1

0 Logic not enabled

1 Enables movement reversal when it stops at the travel limit

TABLE “C”  RADIO MENU RADIO

Logic Description

Add start

Add Start Key

associates the desired key with the Start command

add 2ch

Add 2ch Key

Associates the desired key with the 2nd radio channel command. If no output is congured as 2nd Radio Channel Output, the 2nd radio chan­nel controls the pedestrian opening.

erase 64

Erase List

WARNING! Erases all memorized transmitters from the receiver’s memory.

Read

Read

Checks a key of a receiver and, if memorized, returns the number of the receiver in the memory location (from 01 to 64) and number of the key
(T1-T2-T3 or T4).

Read receiver code

Displays receiver code required for cloning transmitters.

ON = Enables remote programming of cards via a previously memorized W LINK transmitter.
It remains enabled for 3 minutes from the time the W LINK transmitter is last pressed.
OFF= W LINK programming disabled.

ITALY