How it Works
Bernina
Loading...
B 350
Operation Manual
23 pgs2.86 Mb0

Bernina Bernette 20, Bernette 46, Bernette 66, Bernette 92C, Artista 635 Operation Manual

...
Download
Page 1
©2010 BERNINA of America, Inc. Permission granted to copy and distribute in original form only.
Content may not be altered or used in any other form or under any other branding.
Basic Operation
For all current BERNINA models
Including bernettes
Page 2
Table of Contents
Sewing Machine Needles ........................................................................................... 4
Thread ........................................................................................................................ 6
Presser Feet ............................................................................................................... 7
Securing Stitches ........................................................................................................ 8
Turning Corners .......................................................................................................... 9
Zigzag Stitch ............................................................................................................... 10
Blind Hem ................................................................................................................... 11
Triple Straight Stitch ................................................................................................... 12
Vari-Overlock Stitch .................................................................................................... 13
Stretch Stitch .............................................................................................................. 14
Gathering Over Cord .................................................................................................. 15
Buttonholes ................................................................................................................. 16
Manual Buttonholes .................................................................................................... 17
Automatic Buttonholes ................................................................................................ 18
Attaching Buttons ...................................................................................................... 19
Stitching Zippers ......................................................................................................... 20
Stitch, Function, and Foot Charts ............................................................................... 21
1008
8Series
bernette
activa
aurora
12/13/10
artista
3Series
The information in this workbook applies to all current BERNINA
and bernette sewing machines. Note: Some exercises apply only
to models equipped with the highlighted feature.
2
Page 3
Introduction
This workbook is designed to be used as a step-by-step guide to familiarize you with the basic operation of your BERNINA machine, attach the sewn samples to the information pages (or add an extra mounting page as a facing page) and insert the pages into plastic page protectors to store in a 3-ring binder. They can then be used as a reference tool in the future as you use your machine and explore the creative possibilities it affords.
Pages 23-25 of this workbook have several charts that are useful when working through the stitching exer­cises on pages 8-20. Stitch numbers, presser feet, and machine functions are listed for all BERNINA and bernette models. This will help you determine if your machine can be used for the exercise and it will make it faster for you to locate particular stitches. Each stitch exercise page has a graphic of the stitch(es) used so you can quickly find it on the chart and on your machine.
Each page that has a stitching exercise ends with a “Sew How” box. This mini-quiz will let you test your knowl­edge and review the points the exercise is covering. Taking the class is just the first step. Using the informa­tion on a fairly regular basis will help make it become part of your sewing skill set and before long it becomes something you don’t even have to thing about.
BERNINA strives to provide its customers with quality sewing machines, and informative publications and classes. Along with providing My BERNINA Classes, your local BERNINA dealer stocks BERNINA reference books such as Feet-ures and The Serger Technique Reference Book. Plus, BERNINA of America, Inc. has websites offering free projects and a variety of articles and postings that appeal to all types of stitchers, no matter which machines are their favorites. Visit all of these and don’t forget the BERNINA of America blog where you can share ideas and inspiration with other BERNINA enthusiasts!
or bernette sewing machine. Once you have completed the exercises designated for your
www.berninausa.com
www.bernina8series.com
www.berninamylabel.com
www.sewingrepublic.com
www.berninaUSAblog.com
www.throughtheneedle.com
For more ideas and information about using your
BERNINA machine, download Through the Needle ONLINE. This FREE magazine offers fun sewing
projects and informative articles for all types of stitchers: quilters, garment makers, embroiderers, crafters, virtual stitchers, fiber artists and more!
Sign up now for Through the Needle ONLINE at
www.throughtheneedle.com, and you’ll receive an e-mail notification with a link to each new issue when it becomes available. After all, the next best thing to sewing is reading about it!
12/13/10
3
Page 4
Sewing Machine Needles
General Information
Along with thread, needles are very important to stitch formation. Many “mechanical” problems and damage to fabrics can be traced to a bent, damaged, or incorrect size or type needle. When selecting the correct needle, consider the following:
Needle system – 130/705H Needle point – assures proper stitch formation; avoids fabric
damage
Needle size – smaller for lightweight fabrics; larger for heavier
fabrics
If the needle is:
Too small – the thread can’t stay in the groove to form a
loop to be picked up by the hook point
Bent – the thread loop forms too far away from hook point
and the hook can’t enter the loop to form a stitch
Blunt – the needle won’t pierce fabric, so no thread loop
forms to make a stitch
Need to Know
Needles should be changed after every 4-6 hours of stitching. The needle is the most inexpensive part in your sewing machine but it is crucial for getting good results and keeping your machine running well. Don’t let false economy keep you from doing what is best for your sewing projects and your machine.
Needle “Secret” Code
• DRI = Triple
• E = Embroidery
• J = Jeans
• L, LL, R = Leather
• M = Microtex
• MET = Metallica
• N = Topstitching/Cordonnet
• Q = Quilting
• S = Stretch
• SUK = Fine Ball Point
• SES = Medium Ball Point
• WING = Wing
• ZWI = Double
Needle Size Conversion
Regardless of the system, the greater the number, the larger the diameter of the needle.
European vs. Domestic
60 = 8 70 = 10 75 = 11 80 = 12
90 = 14 100 = 16 110 = 18 120 = 19
PartsofaNeedle
Shank (flat side to the back)
Groove (on the front)
Scarf (on the back)
Needle Size for Fabrics
60 – very fine batiste
70 – shirt-weight
80 – medium-weight
90 – denim and twill
100/110/120 – canvas
12/13/10
Eye
Point
The selected thread should fit in the groove on the front of the needle. If it isn’t protected by the groove, a needle with a larger groove should be used.
Always make sure needles are fully inserted as high as possible, with the flat side to the back.
Shaft
4
Page 5
Type Sizes Description
Sewing Machine Needles
Ballpoint
Stretch
Universal
Double
Triple
Jeans
Leather
Microtex / Sharp
Quilting
60-100
70-90
60-120
1.6/70-
8.0/100
2.5/90
3.0/90
70-110
80-100
60-90
75 & 90
Has a rounded point. Size 70 for lingerie, nylon, jersey; 80 for T-shirt; 90 for sweatshirt fleece.
A Stretch needle has a more rounded point than a Ballpoint, and a blue anti-cling coating which helps to prevent skipped stitches in knits and elastic. Sometimes used on Ultrasuede, vinyl, and plastic.
A compromise between a Sharp and a Ballpoint; used on both wovens and knits.
Two needles attached to one shank. For pintucks, hems, and decorative work. Available in Universal, Stretch, Jeans, Metallica, and Embroidery needles.
Three needles attached to one shank. Used to create mock smocking and other decorative effects
Has a sharp point and a shaft that is less prone to flex. The sharpness of the needle is better for use on denim and woven fabrics.
Point is a sharp cutting wedge. Used for leather only. Not for vinyl or simulated leathers.
Sharp point; thin shaft. Specially designed for microfiber fabrics.
Thin, tapered point eliminates potential damage to fabric when seaming and cross-seaming.
Topstitch
Embroidery
Metafil
Wing
Double Wing
Metallica
70-100
75 & 90
80
100 & 110
100
70-100
A sharp point with a large eye and deep groove. For use with heavier fabrics – the large groove cradles heavier threads.
Sharp needle with large eye and groove; has a coating and a larger scarf. Prevents shredding of rayon or metallic threads. Two threads may be used through the eye.
Similar to Embroidery needle with large eye and deep groove. Made of a heat-resistant alloy with a friction-reducing coating. Suitable for manufactured fibers such as polyester, acrylic, and nylon.
Sharp-pointed needle with a non-cutting metal wedge on each side. Makes a hole without cutting the threads of the fabric. Used for decorative and heirloom work, such as hemstitching.
One Universal needle and one Wing needle attached to a single shank.
Designed for metallic threads; has a large eye and deep groove.
12/13/10
5
Page 6
Thread
To achieve quality stitches, a sewing machine needs three things: correct thread, correct size needle, and properly adjusted thread tensions. Poor quality or the wrong type of thread can cause inferior stitches on any machine. Inferior thread results in crooked and looped stitches, puckered seams, frayed thread, and/or needle breakage. Did you know that thread passes through the eye of the needle approximately 37 times in a “seesaw” action before it forms a single stitch?
Long staple threads are stronger and smoother than short staple threads. (Staple refers to the length of fibers used to twist together to form a single ply). Most bargain-priced threads are usually short staple and will deposit more lint and fuzz into your sewing machine, potentially causing tension inconsistencies and possibly even damage to your machine over the long term. Using long staple threads also result in less snagging and fraying as you sew.
Ply refers to the number of strands twisted together to make a single thread. The number of plies are usually indicated by a number after the weight of the thread such as 50/3, which means a 3-ply, 50-wt. thread. The lower the weight, the heavier the thread; conversely, higher numbers indicate fine or lightweight thread.
Guidelines for Thread Weights
12 wt.— Couching, bobbinwork 30 wt.— Embroidery, bobbinwork 40 wt.— General construction, quilting, embroidery 50 wt.— General construction, piecing, bobbin thread 60 wt.— Lingerie, heirloom, appliqué, bobbin thread 80 wt.— Extra-fine lingerie, heirloom
Fibers
Fiber refers to the type of material used to produce the thread.
Polyester
Good for clothing construction on man-made, natural or blended fab­rics. Tolerates high temperatures. Polyester embroidery thread has a high sheen; excellent for embroidery, very abrasion resistant.
Cotton 2 ply
Mettler 60/2; excellent for French heirloom stitching, delicate machine embroidery, piecing and darning.
Mettler 30/2; loose twist for a soft, shiny look in machine embroidery, appliqué, and buttonholes.
Mettler 50/2; excellent for clothing construction on natural fibers. Tighter twist than embroidery cotton thread and less puckering on problem fab­rics. Cotton thread stretches less than polyester.
Rayon
A lustrous embroidery thread; weaker than cotton, it is used for decorative work only.
Silk
Used on silk and wool fabrics, this strong, lustrous fiber is good for construction and decorative details such as buttonholes. Also used for quilting as it blends into the fabric.
12/13/10
The exercises in this work­book are designed to be sewn with Mettler thread. Use one of the following in any color of medium value:
• Metrosene Polyester
• Silk-finished 50-wt. cotton
6
Page 7
Presser Feet
BERNINA Presser Feet:
▪ are precision engineered for specific functions
▪ are Swiss-made for the highest quality
▪ are one-piece metal feet, making them sturdy and durable
▪ are easy to change with one hand, requiring no special tools
▪ have a white shank, making it easier to see the eye of the needle,
resulting in easier threading
▪ are, in some cases, modeled after commercial feet used in factories to increase speed and production with professional results
▪ do the job intended in relation to all types of sewing (example, quilting, garment-making, home dec, etc.)
▪ are supported by the best and most complete educational materials in the
industry, such as Feet-ures volumes 1, 2, & 3, and the BERNINA of
America website at www.berninausa.com
Understanding the Numbers/Letters
BERNINA presser feet are numbered and may have one or two additional versions with a letter that follows the number, such as Edgestitch Foot #10C or Jeans Foot #8D.
Number Only—The number without a letter refers to a foot engineered for BERNINA models that have a
CB Hook and a maximum stitch width of 5.5mm. These feet may also be compatible with models that have a 9mm width when a 9mm width is not desired, such as when making pintucks with feet #30, 31, 32, or 33.
The Letter “C”—When a foot number is followed by a “C”, it indicates a version of the foot made for models
that have rotary hook systems and a maximum stitch width of 9mm. The “C” stands for coded and refers to the sensor on the foot that works with the electronics of the machine to engage the wider stitch width. The
sole of the “C” foot is usually larger to fit the wider feed dog of the rotary hook machines. Exceptions: Overlock
Foot #2/2A: 2A is larger to fit the wider feed dog but does not have a sensor for a wider stitch because the overlock stitches are not used at wide widths. Extra Wide Gathering Foot #16C: 16C is larger to fit the wider feed dog but does not have a sensor for a wider stitch width.
The Letter “D”—The feet that have a number followed by a
“D” are designed to work with the 8-Series (models 830 and
820) Dual Feed feature. After attaching the foot, the Dual Feed mechanism is positioned in the cutout on the back of the foot, engaging the BERNINA Dual Feed system. It is recommended that the D-Feet be used only when the BERNINA Dual Feed Feature is engaged.
Easy-On/Easy-Off Soles—The 3 Series & activa machines
have simple-to-use easy-on/easy-off metal soles that attach to a standard shank. These machines are also compatible with the one-piece full-shank presser feet available as optional accessories for all BERNINA machines.
For complete information on all of the BERNINA presser feet & accessories, see Feet-ures, Vols 1, 2, & 3.
12/13/10
7
Page 8
Fabric: Firm woven fabric, two pieces, 4” x 6” each Needle: 80/12 Universal Needle Position: Center BERNINA Presser Foot: Reverse Pattern Foot #1/1C/1D with
optional Quilting Seam Guide or optional Seam Guides with Rulers
bernette Presser Foot: Zigzag/Universal Foot
Fold each piece of fabric in half lengthwise to be 2” x 6”. Stitch one or both of the exercises below depending on the features of your model.
Exercise 1:
Straight Stitch/Reverse Find the ⅝” guide line on the stitch plate. Fold one piece of fabric in half lengthwise. Place it under the presser foot and align one 6” edge with the ⅝” guide line.
Securing Stitches
Select the straight stitch. Sew a few stitches forward, then press or lift the Quick Reverse Button/Lever; sew a few stitches backward; the machine will sew in reverse until the Quick Reverse Button/Lever is released. Continue stitching the seam;
secure the end in the same way.
Exercise 2:
Securing Stitch Fold the second piece of fabric; align the raw edges with the guide. Place it under the presser foot and align one 6” edge with the ⅝” guide line.
Select the Securing Stitch. Begin to sew; machine will automatically secure the stitching, then continue stitching forward. At the end of the seam, press and release the Quick Reverse button. The machine will automatically secure the
stitching, then stop.
Securing Stitch: Five straight stitches forward and back at beginning; five stitches backward and forward at end.
Quilter’s Securing Stitch: Several very short stitches at the beginning and end.
Do you know how to:
Reverse stitching
Securing stitches
▪ Select straight stitch? ▪ Sew in reverse? ▪ End a seam with the Securing Stitch?
12/13/10
8
Page 9
Fabric: Firm woven fabric, two pieces, 4” x 6” each Needle: 80/12 Universal Needle Position: Center BERNINA Presser Foot: Reverse Pattern Foot #1/1C/1D bernette Presser Foot: Zigzag/Universal Foot
Select the straight stitch.
Place the fabric pieces wrong sides together.
Place the fabric under the foot and engage the Needle Stop Down function, if available (see below).
Sew several lines of stitching, pivoting to form at least 2 right angle corners and 2 additional corners.
Turning Corners
Pivot, using FHS (Free Hand System), if available, to raise the presser foot.
To Access Needle Stop Up/Down: activa, 3 Series, aurora, and artista: Needle stops
in the up position (default). Briefly push the button and needle will go up or down. Press & hold button to set needle stop position down or up automatically until reset. Arrow indicator appears on the screen to show if it set to stop up or down.
8 Series: Needle stops with the needle up and the presser
foot down (default). To change needle setting, touch the Needle Down icon. Machine will stop with the needle down and the presser foot up.
12/13/10
Do you know how to:
▪ Use the Free Hand System? ▪ Use the Stitch Plate markings? ▪ Engage the Needle Stop Down feature?
9
Page 10
Fabric: Firm woven fabric, 4” x 6” Needle: 80/12 Universal Needle Position: As directed in instructions BERNINA Presser Foot: Reverse Pattern Foot #1/1C/1D bernette Presser Foot: Zigzag/Universal Foot
Select the Zigzag Stitch (width = 4, length = 2).
Finish one 6” edge using the following steps.
Guide the edge of the fabric under the middle of the presser foot
– or – Move needle position to the far right; sew using the inside
edge of the right toe as a guide.
Zigzag Stitch
The needle should go into the fabric on one stroke of the needle and over the edge on the next stroke.
Tips Do not use too long a stitch or too wide a stitch; the edge should lie flat, not roll.
Match the weight of the thread to the weight of the fabric.
12/13/10
Do you know how to:
▪Adjust the stitch width? ▪Adjust the stitch length?
10
Page 11
Blind Hem
Fabric: Heavy flannel, 6” x 7” Needle: 80/12 Universal Needle Position: As programmed BERNINA Presser Foot: Reverse Pattern Foot #1/1C/1D and
Blind Hem Foot #5
bernette Presser Foot: Zigzag/Universal Foot and
Blind Hem Foot (optional accessory)
Attach Reverse Pattern Foot #1 or bernette Zigzag/Universal Foot to the machine
Finish one 6” edge of the fabric using a zigzag stitch and guiding the edge of fabric under the middle of the presser foot. The needle should go into the fabric on one stroke of the needle and over the edge on the next stroke. Note: This is the same as the exercise on page 10.
Fold a 2” hem to the wrong side of the fabric and press.
Baste the hem in place, sewing about ¼” from the upper edge of the hem (the one previously stitched).
Select the Blindstitch and attach the Blind Hem Foot to the machine.
Fold the hem back to the right side over the basting line, exposing the zigzagged edge of the fabric.
Sew on the extended hem allowance, keeping the folded edge next to the guide on the foot.
Adjust the stitch width if needed so that the needle barely stitches into the fold.
Unfold the fabric when finished, and notice that the stitches barely show on the outside of the fabric.
Do you know how to:
▪Machine baste? ▪Distinguish between Blind Hem Foot #5
and Edgestitch Foot #10/10C/10D?
12/13/10
11
Page 12
Fabric: Firm woven fabric, two pieces, 4” x 6” each Needle: 80/12 Universal Needle Position: As directed in instructions BERNINA Presser Foot: Reverse pattern Foot #1/1C/1D and
Edgestitch Foot #10/10C/10D
(optional accessory)
bernette Presser Foot: Zigzag/Universal Foot
Attach Reverse Pattern Foot #1/1C/1D or bernette Zigzag/ Universal Foot to the machine.
Select the Triple Straight Stitch.
Position the edge of the fabric on the ⅝” marking on the stitch plate. Sew the seam and press it open.
Triple Straight Stitch
Change to Edgestitch Foot #10/10C/10D and adjust the needle position to the far right.
With the guide of the foot in the ditch of the seam, sew the length of the seam.
Adjust the needle position to the far left and stitch a second time, again with guide of the foot in the ditch of the seam, sewing in the same direction as before.
12/13/10
Do you know how to:
▪ Adjust the needle position? ▪ Use the stitch plate markings? ▪ Use Edgestitch Foot #10/10C/10D?
12
Page 13
Vari-Overlock Stitch
Fabric: Cotton interlock, two pieces, 4” x 6” each Needle: 80/12 Universal (Ballpoint or Stretch may also be used) Needle Position: As programmed BERNINA Presser Foot: Overlock Foot #2/2A bernette Presser Foot: Overcasting Foot (optional accessory)
Place the two pieces of fabric right sides together.
Select the Vari-Overlock Stitch.
If available, engage the Needle Stop Down function.
Guide the raw edges of the fabric under the pin of the foot and stitch the two layers together. The stitch will form over the pin and the edge of the fabric.
bernette: Guide the fabric against the blade of the foot. Adjust the stitch length and width if needed.
12/13/10
Do you know how to:
▪ Engage the Needle Stop Down feature? ▪ Position Overlock Foot #2/2A?
13
Page 14
Fabric: Spandex, two pieces, 2” x 6” each Needle: 80/12 Universal (Ballpoint may also be used) Needle Position: As programmed BERNINA Presser Foot: Reverse pattern Foot #1/1C/1D bernette Presser Foot: Zigzag/Universal Foot
Select the Super Stretch stitch.
Place the fabric pieces right sides together.
Position the edge of the fabric on the ⅝” marking on the stitch plate; sew the seam and press it open.
Note: If the fabric is pulling and stretching as it is sewn, adjust the presser foot pressure to a lower number to lighten the pressure of the foot on the fabric and eliminate the stretching.
Stretch Stitch
12/13/10
Do you know how to:
▪ Adjust the presser foot pressure?
14
Page 15
Gathering Over a Cord
Fabric: Medium weight cotton, 12” x 4” and
Narrow cord such as perle cotton or embroidery floss, 18”
Needle: 80/12 Universal Needle Position: Center BERNINA Presser Foot: Clear Embroidery Foot #39/39C/39D bernette Presser Foot: Cording Foot (optional accessory)
Attach the desired foot to the machine.
Thread the cord through the center front hole of Clear Embroidery Foot #39/39C or through the center groove of the bernette Cording Foot, leaving a 2”-3” tail behind the foot.
Select the Zigzag stitch and adjust the width and length: SW = 2.5mm and SL = 2-2.5mm.
Stitch ⅝” from one 12” edge; sewing over the cord, but not into it.
Tie a knot in the cord at the beginning of the stitching and then pull it to gather the sample to 6”.
Notes
- Gathering over cord adds additional strength, eliminates thread breakage, and allows better control of gathering.
- Do not sew through the cording, or it won‘t be able to move through the channel formed by the stitches
- After gathering the fabric, drop the feed dog and sew a bartack (see page 19) at the beginning and end of cord for strength.
12/13/10
Do you know how to:
▪ Attach a presser foot with one hand? ▪ Adjust stitch width and length? ▪ Drop the feed dog?
15
Page 16
Buttonholes
There are a variety of buttonhole styles available, depending on your model. All models have a standard buttonhole that is appropriate for many types of projects. Below is a list of other styles and types of button­holes that may be available on your model.
STANDARD BUTTONHOLE: Fine to medium weight fabrics.
HEIRLOOM BUTTONHOLE: Fine to medium weight fabrics.
STRETCH BUTTONHOLE: All stretch fabrics.
ROUND BUTTONHOLE WITH NORMAL BARTACK: Medium to heavy weight fabrics of all types.
ROUND BUTTONHOLE WITH HORIZONTAL BARTACK: Medium to heavy weight fabrics of all types.
KEYHOLE BUTTONHOLE WITH NORMAL BARTACK: Heavy weight, non-stretch fabrics.
KEYHOLE BUTTONHOLE WITH POINTED BARTACK: Firm woven fabric. Jackets, coats, leisure wear.
KEYHOLE BUTTONHOLE WITH HORIZONTAL BARTACK: Firm woven fabrics. jackets, coats, leisure wear.
STRAIGHT STITCH BUTTONHOLE: For bound buttonholes & welt pockets.
HAND-LOOK BUTTONHOLE: For light- to medium-weight woven fabrics.
Buttonhole Presser Feet
Standard Buttonhole Foot
#3 for manual buttonholes
on CB models
4-Step Buttonhole Foot For the bernette model 56.
Standard Buttonhole Foot #3C
for manual buttonholes on
rotary models
Automatic Buttonhole Foot #3A
for automatic buttonholes
Automatic Buttonhole Foot For bernette models 66 and 92c.
Buttonhole Foot with Slide #3B
- measuring foot for manual buttonholes
12/13/10
16
Page 17
Manual Buttonholes
Fabric: Heavy flannel, 6” x 6” and
Lightweight tear-away stabilizer, 3” x 6” and
Narrow cord (perle cotton, embroidery floss, etc.), 18”
Needle: 80/12 Universal Needle Position: As programmed BERNINA Presser Foot: Standard Buttonhole Foot #3/3C bernette Presser Foot: Models 46 & 56 only: 4-step Buttonhole Foot
Note: For making buttonholes with bernette models 66 and 92c, see Automatic Button­ holes on the following page.
Fold the fabric in half to 3” x 6”; press. Insert
the stabilizer between the layers. Draw a line
fold
1½” from the fold along the 6” length. Draw a second line 1” from the first line. Mark two short lines, between the fold and the drawn line, spaced about 1½”-2” apart.
Standard Buttonhole—BERNINA
Select the Standard buttonhole; select the “man” function from the function toolbar, if applicable. Position the foot over the first short line, aligning the fold of the fabric with the ⅝” marking on the stitch plate, behind the foot. Engage Step #1. Sew the first side of the buttonhole. Stop at the drawn line; select step #2. Continue with remaining steps.
Standard Buttonhole—bernette 46 and 56
Select the buttonhole and adjust the stitch settings: SW = 5 and SL = buttonhole. Position the foot over the first short line, aligning the needle with the 1½” line. Select the steps in order and sew them as shown in the diagrams. When the stitching is complete, remove the fabric from under the foot. Bring thread tails to the back and tie off.
Corded Buttonhole
Fold the cord in half and loop the middle around the center “toe” of the foot. (For the bernette – loop the cord at the back of the foot; lock it in the front grooves and tie the ends in front.) Stitch the buttonhole on the second line as before, then carefully remove the fabric from under the foot. Pull the cord ends until the loop is pulled up under the buttonhole; trim the ends of cord. If working on a knit fabric, knot the cord ends together before trimming.
Tension Tips A slightly tighter bobbin tension gives a beautiful full look to your buttonholes. The best way to achieve this:
• CB Hook Machines: Thread the bobbin thread through the hole in the finger of the bobbin case.
• Rotary Hook Machines: Use the embroidery bobbin case and thread the "pigtail."
Do you know how to:
▪ Measure a button for buttonhole size? ▪ Select a buttonhole? ▪ Stitch a buttonhole?
• 8 Series Machines: Thread for embroidery.
bernette 46
bernette 56
12/13/10
17
Page 18
Automatic Buttonholes
Fabric: Heavy flannel, 6” x 6” and
Lightweight tear-away stabilizer, 3” x 6”
Needle: 80/12 Universal BERNINA Presser Foot: Automatic Buttonhole Foot #3A bernette Presser Foot: Automatic Buttonhole Foot
Note: Models 1008 & activa 210 do not make Automatic Buttonholes.
Fold each fabric square in half to 3” x 6”; press. Insert the stabilizer between the layers. Draw a line 1½” from the fold along the 6” length.
Automatic Buttonhole—BERNINA
▪ Attach Automatic Buttonhole Foot #3A; set the red slide marker to the length of buttonhole desired. ▪ Position the needle over the drawn line, setting it to stitch the buttonhole perpendicular to the line. ▪ Sew the first bead of the buttonhole; stop when the red mark on the foot aligns with the red slide marker. ▪ Press the Quick Reverse button; this programs the length of the buttonhole. Continue sewing – the buttonhole is completed automatically and the machine will stop when it is finished. This buttonhole is now programmed into the temporary memory. ▪ Move the foot to another place on the drawn line and sew the programmed buttonhole on the second line. There is no need to stop or press Quick Reverse this time as the machine will simply repeat the previous buttonhole and stop automatically.
Automatic Buttonhole—bernette 66 and 92c
▪ Position the foot over the first short line, aligning the needle (at the front end of the buttonhole) with the drawn line.
• Open the button plate and insert the button.
• Lower the buttonhole lever and push it toward the back of the machine.
• Stitch the buttonhole; the machine will complete the buttonhole automatically.
▪ When stitching is complete, remove the fabric from under the presser foot.
▪ Bring the thread tails to back and tie off.
▪ Push the lever up when not in use.
Note: To make a corded Automatic Buttonhole on bernette models 66 and 92C, follow the directions on the previous page, looping the cord from the back and securing it at the front of the foot.
12/13/10
Do you know how to:
▪ Program a buttonhole? ▪ Make repeat buttonholes? ▪ Open a buttonhole?
18
Page 19
Fabric: Firm woven fabric, 4” x 8” and
Lightweight tear-away stabilizer, 4” x 4”
Needle: 80/12 Universal BERNINA Presser Foot: Button Sew-On Foot #18 (optional) bernette Presser Foot: Button Sew-On Foot (optional)
Lower the feed dog, then attach the Button Sew-On Foot to the machine. Select the Button Sew-On stitch, if available. The Univer­sal or Zigzag stitch can also be used by setting the stitch length at
0.0mm.
Fold the fabric in half to 4” x 4”; press. Insert the stabilizer between the layers of fabric.
Technique #1 – With Thread Shank
Optional: Use a glue stick to hold the button in place.
BERNINA only: For a long shank, adjust the pin on Button Sew-On Foot #18 to the highest position. Note: A short shank is appropriate
for dress-and blouse-weight fabrics; a long shank for coat- and jacket-weight materials.
Check the distance between the holes of the button by turning the hand wheel. To avoid breaking the needle, adjust the stitch width if necessary so that the left and right swings of the needle fall into the holes of the button. Hold the thread tails as you begin to sew.
If using the Button Sew-on stitch, the machine stops automatically when the program is complete; the thread tails are secured as part of the program.
BERNINA or bernette: Use the Universal or Zigzag stitch, sew 6-8
stitches, and stop. Bring the thread tails to the wrong side of the fabric and knot them together; trim the excess thread
Technique #2 – Without Thread Shank Using the lowest shank setting and the instructions above, attach a charm(s) or snap or hook and eye. Stitch a ribbon with this technique (the stitch makes a bartack) and then tie the ribbon into a bow.
.
Do you know how to:
Attaching Buttons
▪ Lower the feed dog? ▪ Adjust the shank on Button Sew-On
Foot #18?
12/13/10
19
Page 20
Fabric: Firm woven fabric, two pieces, 4” x 8” each and
4”-7” neckline zipper
Needle: 80/12 Universal BERNINA Presser Foot: Reverse Pattern Foot #1/1C/1D and
Zipper Feet #4 and
Zipper Foot with Guide #14
bernette Presser Foot: Zigzag/Universal foot and
Zipper Foot
Attaching the Zipper to Garment
Place fabric pieces right sides together. Using a straight stitch, sew a ¾” seam from one short end up to where the zipper stop will be (about 2”). Baste the rest of the seam, sewing 2-3 stitches in reverse at the end to secure the seam; return to a straight stitch length of 2.5mm.
Press the seam allowances open. Place the right side of the zipper against the seam allowances with the zipper teeth centered over the
seam. Pin or baste each side of zipper to the seam allowances only.
Change to a zipper foot; adjust the needle position (bernette users slide the zipper foot) to the right or left as needed to stitch close to
the zipper teeth. Sew through the zipper tape and the seam allowance only, from bottom to top on each side of the zipper. Pin or baste
through all layers to hold the sewn zipper to the project.
Topstitching the Zipper—BERNINA
Change to Zipper Foot with Guide #14.
Left Side: Adjust the seam guide to one notch to the right of center.
Adjust the needle position to the far left. Sewing from the right side of the fabric and starting at the lower edge, sink the needle into the seam. Sew out about ⅜ ”, stop, pivot and make sure the seam guide is lying in the ditch of the seam. Sew up the left side of the zipper, stitching through all layers.
Right Side: Adjust the guide one notch to left of center; move the
needle position to the far right. Repeat the above steps on the right side of the zipper.
Topstitching the Zipper—bernette
Left Side: Adjust the foot to the left of center. Sewing from
the right side of the fabric and starting at the lower edge, sink the needle into the seam. Sew out about ⅜ ”, stop, pivot and make sure the edge of the foot is lying in the ditch of the seam. Sew up the left side of the zipper.
Right Side: Adjust foot to right of center. Repeat the above
steps, starting at seam and sewing to the right of the zipper.
Do you know how to:
▪ Machine baste a seam? ▪ Adjust the needle positions? ▪ Adjust the sliding guide or sole?
Stitching Zippers
12/13/10
20
Page 21
12/13/10
The following stitches are used in Workbook 1: Basic Operation. The chart gives the stitch number for each model (-- indicates that the stitch is not available).
Stitch Chart
8 Series artista aurora 3 Series activa classic bernette
830 820 730 640 635LE 630 450 440QE 430 380 350PE 330 210 1008 92c 66 56 46*
Basting
21 21 21 21 30 30 21 21 19 23 21 -- -- -- -- -- -- --
Blindstitch
9 9 9 9 9 9 7 7 7 7 7 7 5 3 13 12 5 7
Button Sew-On
60 60 60 60 60 60 17 17 16 14 12 11 -- -- -- -- -- --
Quilter’s Securing
1324 1324 324 324 324 324 -- -- -- 104 75 -- -- -- -- -- -- --
Securing
5 5 5 5 5 5 5 5 5 5 5 5 -- -- -- -- -- --
Standard Buttonhole
51 51 51 51 51 51 10 10 10 0 0 0 11 dial 1 1 1 dial
Straight
1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 1 & 2
Stretch
11 11 11 11 11 11 9 9 9 9 9 9 -- -- -- -- -- --
Triple Straight
6 6 6 6 6 6 6 6 6 6 6 6 4 5 51 16 14 --
Universal
15 15 15 15 15 15 15 26 24 19 17 14 -- 4 6 6 8 --
Vari­Overlock
3 3 3 3 3 3 3 3 3 3 3 3 -- 3 6 5 7 6
Zigzag
2 2 2 2 2 2 2 2 2 2 2 2 2 2 3 3 3 3
Stitch
— ▪ —
* The stitches on bernette model 46 are not numbered on the machine but are indicated on the chart in the order they appear on the front of the machine.
21
Page 22
12/13/10
8 Series artista aurora 3 Series activa mechanical bernette
Feature/ Function
830 820 730 640 635LE 630 450 440QE 430 380 350PE 330 210 1008 92c 66 56 46
Automatic One­Step Buttonhole
yes yes yes yes yes yes yes yes yes yes yes yes no no yes yes yes no
Feed Dog Up/Down
yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes
Free Hand System
yes yes yes yes yes yes yes yes yes yes opt opt no no no no no no
Hopper Mechanism
yes yes yes yes yes yes yes yes yes yes yes yes yes no no no no no
Needle Positions
11 11 11 11 11 11 11 11 11 9 9 9 9 5
Needle Stop Down
yes yes yes yes yes yes yes yes yes yes yes yes yes no
yes no no no
On-screen Button­hole Measuring
yes yes yes yes yes yes no no no no no no no no no no no no
Presser Foot Pressure
yes yes yes yes yes yes yes yes yes yes yes yes no no yes yes yes yes
Slide-on Tray
yes yes yes yes yes yes yes yes yes yes yes opt yes yes yes yes yes yes
The following features and functions are used in Workbook 1: Basic Operation.
Machine Features & Functions
22
Page 23
12/13/10
8 Series artista aurora 3 Series activa classic bernette
Presser Feet
830 820 730 640 635LE 630 450 440QE 430 380 350PE 330 210 1008 92c 66 56 46
Reverse Pattern Foot #1/1C/1D
1C &
1D
1C &
1D
1C 1C 1 1 1C 1 1
1 1 1 1 1 C C J X
Overlock Foot #2/2A
2A -- 2A 2A -- 2 2A -- 2 2 -- -- -- 2 -- -- -- --
Standard Button­hole Foot #3/3C
3C -- 3C 3C -- 3 -- -- -- -- -- -- 3 3 -- -- B X
Auto Buttonhole Foot #3A
3A 3A 3A 3A 3A 3A 3A 3A 3A 3A 3A 3A -- -- D D -- --
Zipper Foot #4/4D
4D 4D 4 4 4 4 4 4 4 4 4 4 4 4
I I I
X
Blind Hem Foot #5
5 5 5 5 5 5 5 5 5 5 5 5 5 5 X -- -- --
Jeans Foot #8/8D
-- -- 8 -- -- -- -- -- -- 8 -- 8 -- -- -- -- -- --
Darning Foot #9
-- -- -- 9 -- 9 9 9 9 -- -- -- -- -- X -- -- --
Button Sew-On Foot #18
18 -- 18 -- -- -- -- -- -- -- -- -- -- -- X X X X
Open Embroidery Foot #20/20C/20D
20C 20C 20C 20C 20 20 20C 20 -- 20 -- 20 -- -- X -- -- --
Patchwork Foot #37/37D
-- 37D -- -- -- -- -- 37 -- -- 37 -- -- -- X -- -- --
Sideways Motion Foot #40C
40C -- 40C -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
BERNINA Stitch Regulator #42
42 42 42 -- -- -- -- 42 -- -- -- -- -- -- -- -- -- --
Walking Foot #50
-- -- -- -- -- -- -- 50 -- -- -- -- -- -- -- -- -- --
Circular Embroi­dery Attachment 83
-- -- -- -- 83 -- -- -- -- -- -- -- -- -- -- -- -- --
Freemotion Couching Foot #43
-- -- -- -- 43 -- -- -- -- -- -- -- -- -- -- -- --
Presser Foot Chart
The presser feet listed below are included with the purchase of each model as indicated on the chart (-- indicates that the presser foot is not included but may be available as an optional accessory). The BERNINA name and numbers are listed and if the bernette has a corresponding presser foot, it is indicated by the letter
stamped on the top of the sole. If the bernette foot does not have a letter, it is indicated by an “X”. The highlighted feet have snap-on soles.
23
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use