Bently Nevada 9100D Specifications

M O D E L 9 1 0 0 D

PORTABLE SHAKER TABLE

The 9100D Portable Shaker Table is the ideal tool to field check accelerometers, velocity transducers and proximity probes over a wide operating frequency and amplitude range. The unit is a small, handy, completely self-contained vibration reference source which can be conveniently used to validate the entire channel of transducers through measurement, monitoring or recording systems. Packaged in a lightweight, durable Pelican latches and padlockable clasps, the 9100D is always ready for travel to test sites.

Storm Case with two press and pull

With an integral, precision quartz reference accelerometer, the shaker table is built with robust carbon fiber composite armature flexure supports. Closed loop level control gives the 9100D superior quality vibration calibration from 7 Hz to 10 kHz compared with other portable field calibrators.

B E N E F I T S:

• Small and completely self-contained, ideal for field check of

accelerometers, velocity transducers and proximity probes

• Lightweight, industrial Pelican®Storm Case dramatically improves

durability and portability

• Precision quartz reference accelerometer and conditioning electronics

for superior control and stability

• Rugged shaker element design with carbon fiber composite armature

flexures

• Increased battery life and enhanced protection against full discharge

• Provides NIST traceable transducer verification across a wide

frequency and amplitude range

80 0 -8 6 0- 4 86 7

in f o@ m od a ls h op . co m

“Simplifying with Smart Sensing Solutions”

M O D E L 9 1 0 0 D

SPECIFICATIONS:

NERAL

Frequency Range (operating, 100 gram payload) 7 Hz to 10 kHz

Maximum Amplitude (100 Hz with no payload) 20 g pk (196 m/s2pk)

Maximum Payload

Acceleration (30 Hz to 2 kHz) ±3% Acceleration (7 Hz to 10 kHz) ±1 dB Velocity (10 Hz to 1000 Hz) ±3% Displacement (30 Hz to 150 Hz) ±3% Amplitude Linearity (100 gram payload, 100 Hz) < 1% up to 10 g pk Waveform Distortion (100 gram payload, 30 Hz to 2 kHz) < 5% THD (typical) up to 5 g pk

UNITS OF READOUT

Acceleration (peak and RMS) g, m/s Velocity (peak and RMS) in/s, mm/s Displacement (peak to peak) mils, µm Frequency Hz, CPM

INPUT/OUTPUT

External Source In (Max) 1V AC RMS Monitor Reference Out 10 mV/g (nominal), buffered internal reference output

POWER REQUIREMENTS

Internal Battery (sealed solid gel lead acid) 12 VDC, 4 amp hours AC Power (for recharging battery) 110-240 Volts, 50-60 Hz Operating Battery Life

TEMPERATURE

Operating 32° - 122° F (0° - 50° C)

PHYSICAL

Dimensions (H x W x D) 8.5 in x 12 in x 10 in (22 cm x 30.5 cm x 28 cm) Weight 18 lb (8.2 kg)

Sensor Mounting Platform Thread Size

[1] Operating range reduced at higher payloads. Reference manual for full details. [2] As shipped from factory in new condition.

INCLUDED ACCESSORIES

Accessory Pouch Includes: Mounting Wrench, Power Supply and Plug Adaptors, 1⁄4-28 to 1⁄4-28 Adaptor, 10-32 to 1⁄4-28 Adaptor and Mounting Pad

ACCESSORY PRODUCTS FOR 9100D

9100-MNTKIT Mounting accessory kit to adapt to ¼-28 threaded mounting platforms. Includes studs/inserts

9105C Transfer standard reference accelerometer and ICP®sensor signal conditioner, for calibration and system

9100-MPPA01 Proximity probe adaptor kit, supports probes with common case threads ranging from M6 to 3/8 in. Includes

9100-PPA01 Proximity probe adaptor kit, supports probes with common case threads ranging from M6 to 3/8 in. Includes

9100-PPA02 Target for 9100-PPA01 or 9100-MPPA01 proximity probe adaptor kit, nickel plated 4140 steel. 9100-PS01 18 V, 1 A power supply/charger for 9100 Series Calibrator, universal 100-240 VAC, 50/60 Hz. 9100-BAT01 Replacement battery for 9100 Series Calibrators.

[1]

CURACY OF

100 gram payload, 100 Hz 1 g pk 18 hours 100 gram payload, 100 Hz 10 g pk 1 hour

ADOUT

[

EASURED WITH

RAM QUARTZ REFERENCE ACCELEROMETER

10 G

(¼-28, 10-32, 6-32 and 5-40) and bases (for adhesive, magnetic, and custom thread patterns).

verification of the 9100 Series Calibrators.

Mitutoyo micrometer (metric) and 9100-PPA02 nickel plated 4140 steel target.

Mitutoyo micrometer and 9100-PPA02 nickel plated 4140 steel target.

420 to 600 k cpm

15 in/s pk (380 mm/s pk) 50 mils pk-pk (1270 µm pk-pk) 800 gram

⁄4-28

The Modal Shop 3149 E Kemper Road, Cincinnati, OH 45241 USA

Toll free 8 00 - 86 0 -4 8 67 / Phone 5 1 3- 3 51 - 99 1 9 / Fax 5 1 3 - 4 5 8 - 2 1 7 2

E-mail i n fo @ mo d al s ho p .c o m Website w w w . m o d a l s h o p . c o m

DS-0090 rev I Printed in U.S.A.

PCB and ICP are registered trademarks of PCB Group, Inc. Pelican

is a trademark of Pelican Products, Inc.