Beko WTE 6531 X0 User manual [EN,UK]
Washing Machine
User’s Manual
Пральна машина
Посібник користувача
WTE 6531 X0
Document Number
2820524817_EN / 22-05-15.(17:09)
1 Important instructions for safety and environment
This section contains safety instructions that will help protect from risk of
personal injury or property damage. Failure to follow these instructions
shall void any warranty.
1.1 General safety
• This product can be used by children at and above 8 years old and by
persons whose physical, sensory or mental capabilities were not fully
developed or who lack experience and knowledge provided that they
are supervised or trained on the safe usage of the product and the risks it brings out. Children must not play with the product. Cleaning and
maintenance works should not be performed by children unless they are
supervised by someone. Children of less than 3 years should be kept
away unless continuously supervised.
• Never place the product on a carpet-covered floor. Otherwise, lack of
airflow beneath the machine will cause electrical parts to overheat. This
will cause problems with your product.
• If the product has a failure, it should not be operated unless it is repaired
by the Authorized Service Agent. There is the risk of electric shock!
• This product is designed to resume operating in the event of powering
on after a power interruption. If you wish to cancel the programme, see
"Cancelling the programme" section.
• Connect the product to a grounded outlet protected by a 16 A fuse. Do
not neglect to have the grounding installation made by a qualified electrician. Our company shall not be liable for any damages that will arise
when the product is used without grounding in accordance with the local
regulations.
• The water supply and draining hoses must be securely fastened and remain undamaged. Otherwise, there is the risk of water leakage.
• Never open the loading door or remove the filter while there is still water
in the drum. Otherwise, risk of flooding and injury from hot water will occur.
• Do not force open the locked loading door. The loading door will be ready to open just a few minutes after the washing cycle comes to an end.
In case of forcing the loading door to open, the door and the lock mechanism may get damaged.
• Unplug the product when not in use.
• Never wash the product by spreading or pouring water onto it! There is
the risk of electric shock!
This product was manufactured using the latest technology in environmentally friendly conditions.
• Never touch the plug with wet hands! Never unplug by pulling on the cable, always pull out by grabbing the plug.
• Use detergents, softeners and supplements suitable for automatic washing machines only.
• Follow the instructions on the textile tags and on the detergent package.
• The product must be unplugged during installation, maintenance, cleaning and repairing procedures.
• Always have the installation and repairing procedures carried out by
the Authorized Service Agent. Manufacturer shall not be held liable for
damages that may arise from procedures carried out by unauthorized
persons.
• If the power cable is damaged, it must be replaced by the manufacturer,
after sales service or a similarly qualified person (preferably an electrician) or someone designated by the importer in order to avoid possible
risks.
• Place the product on a rigid, flat and level surface.
• Do not place it on a long-pile rug or similar surfaces.
• Do not place the product on a high platform or near the edge on a cascaded surface.
• Do not place the product on the power cable.
• Never use sponge or scrub materials. These will damage the painted,
chrome plated and plastic surfaces.
1.2 Intended use
• This product has been designed for domestic use. It is not suitable for
commercial use and it must not be used out of its intended use.
• The product must only be used for washing and rinsing of laundry that
are marked accordingly.
• The manufacturer waives any responsibility arisen from incorrect usage
or transportation.
1.3 Children's safety
• Packaging materials are dangerous to children. Keep packaging materials in a safe place away from reach of the children.
• Electrical products are dangerous for the children. Keep children away
from the product when it is in use. Do not let them to tamper with the
product. Use child lock to prevent children from intervening with the product.
• Do not forget to close the loading door when leaving the room where the
product is located.
• Store all detergents and additives in a safe place away from the reach
of the children by closing the cover of the detergent container or sealing
the detergent package.
3 / EN
Washing Machine / User’s Manual
While washing the laundry at high temperatures, the loading
door glass becomes hot. Therefore, keep especially the children away from the loading door of the machine while the
washing operation is in progress.
1.4 Package information
• Packaging materials of the product are manufactured from recyclable
materials in accordance with our National Environment Regulations. Do
not dispose of the packaging materials together with the domestic or
other wastes. Take them to the packaging material collection points designated by the local authorities.
1.5 Disposing of the waste product
• This product has been manufactured with high quality parts and materials which can be reused and are suitable for recycling. Therefore, do
not dispose the product with normal domestic waste at the end of its
service life. Take it to a collection point for the recycling of electrical and
electronic equipment. Please consult your local authorities to learn the
nearest collection point. Help protect the environment and natural resources by recycling used products. For children's safety, cut the power
cable and break the locking mechanism of the loading door so that it will
be non-functional before disposing of the product.
1.6 Compliance with WEEE Directive
This product complies with EU WEEE Directive
(2012/19/EU). This product bears a classification symbol for waste electrical and electronic equipment
(WEEE).
This product has been manufactured with high quality
parts and materials which can be reused and are suitable for recycling. Do not dispose of the waste product
with normal domestic and other wastes at the end of
its service life. Take it to the collection center for the recycling of electrical and electronic equipment. Please
consult your local authorities to learn about these collection centers.
Compliance with RoHS Directive:
The product you have purchased complies with EU
RoHS Directive (2011/65/EU). It does not contain har-
mful and prohibited materials specified in the Directive.
4 / EN
Washing Machine / User’s Manual
2 Installation
Refer to the nearest Authorised Service Agent for
installation of the product. To make the product ready
for use, review the information in the user manual
and make sure that the electricity, tap water supply
and water drainage systems are appropriate before
calling the Authorized Service Agent. If they are not,
call a qualified technician and plumber to have any
necessary arrangements carried out.
NOTE : Preparation of the location and
electrical, tap water and waste water installations
C
at the place of installation is under customer's
responsibility.
NOTE : Make sure that the water inlet and
discharge hoses as well as the power cable are
not folded, pinched or crushed while pushing the
product into its place after installation or cleaning
procedures.
DANGER: Installation and electrical
connections of the product must be carried out by
B
the Authorized Service Agent. Manufacturer shall
not be held liable for damages that may arise
from procedures carried out by unauthorized
persons.
CAUTION: Prior to installation, visually check
if the product has any defects on it. If so, do not
A
have it installed. Damaged products cause risks
for your safety.
2.1 Appropriate installation location
• Place the machine on a rigid floor. Do not place it on
a long pile rug or similar surfaces.
• Total weight of the washing machine and the dryer
-with full load- when they are placed on top of each
other reaches to approx. 180 kilograms. Place the
product on a solid and flat floor that has sufficient
load carrying capacity!
• Do not place the product on the power cable.
• Do not install the product at places where
temperature may fall below 0ºC.
• Place the product at least 1 cm away from the edges
of other furniture.
2.2 Removing packaging reinforcement
Tilt the machine backwards to remove the packaging
reinforcement. Remove the packaging reinforcement
by pulling the ribbon.
2.3 Removing the transportation locks
WARNING: Do not remove the transportation
locks before taking out the packaging
A
reinforcement.
WARNING: Remove the transportation safety
bolts before operating the washing machine!
Otherwise, the product will be damaged.
1. Loosen all the bolts with a suitable spanner until
they rotate freely
(C).
5 / EN
Washing Machine / User’s Manual
2. Remove transportation safety bolts by turning them
gently.
3. Attach the plastic covers supplied in the User
Manual bag into the holes on the rear panel.
NOTE : Keep the transportation safety bolts in
a safe place to reuse when the washing machine
C
needs to be moved again in the future.
NOTE : Never move the product without the
transportation safety bolts properly fixed in place!
(P)
2.4 Connecting water supply
NOTE : The water supply pressure required to
run the product is between 1 to 10 bars (0.1 – 1
C
MPa). It is necessary to have 10 – 80 liters of
water flowing from the fully open tap in one minute
to have your machine run smoothly. Attach a
pressure reducing valve if water pressure is higher.
NOTE : If you are going to use the double water-
inlet product as a single
you must install the supplied stopper to the hot
water valve before operating the product. (Applies
for the products supplied with a blind stopper
group.)
WARNING: Models with a single water inlet
should not be connected to the hot water tap. In
A
such a case the laundry will get damaged or the
product will switch to protection mode and will not
operate.
WARNING: Do not use old or used water inlet
hoses on the new product. It may cause stains on
your laundry.
1. Connect the special hoses supplied with the product
to the water inlets on the product. Red hose (left)
(max. 90 ºC) is for hot water inlet, blue hose (right)
(max. 25 ºC) is for cold water inlet.
(cold) water-inlet unit,
CAUTION: Ensure that the cold and hot water
connections are made correctly when installing
A
the product. Otherwise, your laundry will come
out hot at the end of the washing process and
wear out.
2. Tighten all hose nuts by hand. Never use a tool
when tightening the nuts.
3. Open the taps completely after making the
hose connection to check for water leaks at the
connection points. If any leaks occur, turn off the
tap and remove the nut. Retighten the nut carefully
after checking the seal. To prevent water leakages
and damages caused by them, keep the taps closed
when the machine is not in use.
6 / EN
Washing Machine / User’s Manual
2.5 Connecting to the drain
• The end of the drain hose must be directly
connected to the wastewater drain or to the
washbasin.
CAUTION: Your house will be flooded if the
hose comes out of its housing during water
A
discharge. Moreover, there is risk of scalding due
to high washing temperatures! To prevent such
situations and to ensure smooth water intake
and discharge of the machine, fix the end of the
discharge hose tightly so that it cannot come out.
• The hose should be attached to a height of at least
40 cm, and 100 cm at most.
• In case the hose is elevated after laying it on the
floor level or close to the ground (less than 40 cm
above the ground), water discharge becomes more
difficult and the laundry may come out excessively
wet. Therefore, follow the heights described in the
figure.
100cm
40cm
• To prevent flowing of dirty water back into the
machine and to allow for easy discharge, do not
immerse the hose end into the dirty water or do not
drive it in the drain more than 15 cm. If it is too long,
cut it short.
• The end of the hose should not be bent, it should
not be stepped on and the hose must not be
pinched between the drain and the machine.
• If the length of the hose is too short, use it by adding
an original extension hose. Length of the hose
may not be longer than 3.2 m. To avoid water leak
failures, the connection between the extension hose
and the drain hose of the product must be fitted well
with an appropriate clamp as not to come off and
leak.
2.6 Adjusting the feet
CAUTION: In order to ensure that the product
operates more silently and vibration-free, it must
A
stand level and balanced on its feet. Balance
the machine by adjusting the feet. Otherwise,
the product may move from its place and cause
crushing and vibration problems.
1. Loosen the lock nuts on the feet by hand.
2. Adjust the feet until the product stands level and
balanced.
3. Tighten all lock nuts again by hand.
WARNING: Do not use any tools to loosen the
lock nuts. Otherwise, they will get damaged.
A
2.7 Electrical connection
Connect the product to a grounded outlet protected
by a 16 A fuse. Our company shall not be liable for
any damages that will arise when the product is
used without grounding in accordance with the local
regulations.
• Connection must comply with national regulations.
• Power cable plug must be within easy reach after
installation.
• If the current value of the fuse or breaker in the
house is less than 16 Amps, have a qualified
electrician install a 16 Amp fuse.
• The voltage specified in the "Technical
specifications" section must be equal to your mains
voltage.
• Do not make connections via extension cables or
multi-plugs.
DANGER: Damaged power cables must be
replaced by the Authorized Service Agents.
B
Transportation of the product
1. Unplug the product before transporting it.
2. Remove water drain and water supply connections.
3. Drain all water that has remained in the product.
4. Install transportation safety bolts in the reverse order
of removal procedure;
NOTE : Never move the product without the
C
transportation safety bolts properly fixed in place!
CAUTION: Packaging materials are dangerous
to children. Keep packaging materials in a safe
A
place away from reach of the children.
7 / EN
Washing Machine / User’s Manual
3 Preparation
3.1 Sorting the laundry
• Sort laundry according to type of fabric, colour, and
degree of soiling and allowable water temperature.
• Always obey the instructions given on the garment
tags.
3.2 Preparing laundry for washing
• Laundry items with metal attachments such as,
underwired bras, belt buckles or metal buttons will
damage the machine. Remove the metal pieces or
wash the clothes by putting them in a laundry bag or
pillow case.
• Take out all substances in the pockets such as coins,
pens and paper clips, and turn pockets inside out
and brush. Such objects may damage the product or
cause noise problem.
• Put small size clothes such as infant's socks and
nylon stockings in a laundry bag or pillow case.
• Place curtains in without compressing them.
Remove curtain attachment items.
• Fasten zippers, sew loose buttons and mend rips
and tears.
• Wash “machine washable” or “hand washable”
labeled products only with an appropriate
programme.
• Do not wash colours and whites together. New, dark
coloured cottons release a lot of dye. Wash them
separately.
• Tough stains must be treated properly before
washing. If unsure, check with a dry cleaner.
• Use only dyes/colour changers and limescale
removers suitable for machine wash. Always follow
the instructions on the package.
• Wash trousers and delicate laundry turned inside
out.
• Keep laundry items made of Angora wool in the
freezer for a few hours before washing. This will
reduce pilling.
• Laundry that are subjected to materials such as
flour, lime dust, milk powder, etc. intensely must be
shaken off before placing into the machine. Such
dusts and powders on the laundry may build up on
the inner parts of the machine in time and can cause
damage.
3.3 Things to be done for energy saving
Following information will help you use the product in
an ecological and energy-efficient manner.
• Operate the product in the highest capacity allowed
by the programme you have selected, but do not
overload; see, "Programme and consumption table".
• Always follow the instructions on the detergent
packaging.
• Wash slightly soiled laundry at low temperatures.
• Use faster programmes for small quantities of lightly
soiled laundry.
• Do not use prewash and high temperatures for
laundry that is not heavily soiled or stained.
• If you plan to dry your laundry in a dryer, select the
highest spin speed recommended during washing
process.
• Do not use detergent in excess of the amount
recommended on the detergent package.
3.4 Initial use
Before starting to use the product, make sure that
all preparations are made in accordance with the
instructions in sections “Important safety instructions”
and “Installation”.
To prepare the product for washing laundry, perform
first operation in Drum Cleaning programme. If
your product is not equipped with Drum Cleaning
programme, perform the Initial Use procedure in
accordance with the methods described under “5.2
Cleaning the loading door and the drum” section of the
user manual.
NOTE : Use an anti-limescale suitable for the
washing machines.
C
NOTE : Some water might have remained in the
product due to the quality control processes in the
production. It is not harmful for the product.
3.5 Correct load capacity
The maximum load capacity depends on the type
of laundry, the degree of soiling and the washing
programme desired.
The machine automatically adjusts the amount of water
according to the weight of the loaded laundry.
CAUTION: Follow the information in the
“Programme and consumption table”. When
A
overloaded, machine's washing performance will
drop. Moreover, noise and vibration problems may
occur.
3.6 Loading the laundry
1. Open the loading door.
2. Place laundry items loosely into the machine.
3. Push the loading door to close until you hear a
locking sound. Ensure that no items are caught in
the door.
NOTE : The loading door is locked while a
programme is running. The door can only be
C
opened a while after the programme comes to an
end.
CAUTION: In case of misplacing the laundry,
noise and vibration problems may occur in the
A
machine.
3.7 Using detergent and softener
NOTE : When using detergent, softener, starch,
fabric dye, bleach or limescale remover read
C
the manufacturer's instructions on the package
carefully and follow the suggested dosage values.
Use measuring cup if available.
Detergent Drawer
The detergent drawer is composed of three
compartments:
– (1) for prewash
– (2) for main wash
– (3) for softener
– (*) in addition, there is siphon piece in the softener
compartment.
8 / EN
Washing Machine / User’s Manual
2
1
3
Detergent, softener and other cleaning agents
• Add detergent and softener before starting the
washing programme.
• Never leave the detergent drawer open while the
washing programme is running!
• When using a programme without prewash, do not
put any detergent into the prewash compartment
(compartment nr. "1").
• In a programme with prewash, do not put
liquid detergent into the prewash compartment
(compartment nr. "1").
• Do not select a programme with prewash if you are
using a detergent bag or dispensing ball. Place the
detergent bag or the dispensing ball directly among
the laundry in the machine.
• If you are using liquid detergent, do not forget to
place the liquid detergent cup into the main wash
compartment (compartment nr. "2").
Choosing the detergent type
The type of detergent to be used depends on the type
and colour of the fabric.
• Use different detergents for coloured and white
laundry.
• Wash your delicate clothes only with special
detergents (liquid detergent, wool shampoo, etc.)
used solely for delicate clothes.
• When washing dark coloured clothes and quilts, it is
recommended to use liquid detergent.
• Wash woolens with special detergent made
specifically for woolens.
CAUTION: Use only detergents manufactured
specifically for washing machines.
A
CAUTION: Do not use soap powder.
Adjusting detergent amount
The amount of washing detergent to be used depends
on the amount of laundry, the degree of soiling and
water hardness.
• Do not use amounts exceeding the dosage
quantities recommended on the detergent package
to avoid problems of excessive foam, poor rinsing,
financial savings and finally, environmental
protection.
• Use lesser detergent for small amounts or lightly
soiled clothes.
Using softeners
Pour the softener into the softener compartment of the
detergent drawer.
• Do not exceed the (>max<) level marking in the
softener compartment.
• If the softener has lost its fluidity, dilute it with water
before putting it in the detergent drawer.
Using liquid detergents
If the product contains a liquid detergent cup:
• Make sure that you have placed the liquid detergent
cup in compartment nr. "2".
• If the liquid detergent has lost its fluidity, dilute it with
water before putting in the detergent cup.
Clothes
Light colours and whites
(Recommended temperature range
based on soiling level: 40-90 °C)
It may be necessary to pre-treat the
stains or perform prewash. Powder
Heavily Soiled
(difficult stains
such as grass,
coffee, fruits
and blood.)
Normally Soiled
(For example,
stains caused
Soiling Level
by body on
collars and
cuffs)
Lightly Soiled
(No visible
stains exist.)
and liquid detergents recommended
for whites can be used at dosages
recommended for heavily soiled
clothes. It is recommended to use
powder detergents to clean clay and
soil stains and the stains that are
sensitive to bleaches.
Powder and liquid detergents
recommended for whites can be used
at dosages recommended for normally
soiled clothes.
Powder and liquid detergents
recommended for whites can be used
at dosages recommended for lightly
soiled clothes.
Colours
(Recommended temperature range
based on soiling level: cold -40 °C)
9 / EN
Washing Machine / User’s Manual
Clothes
Powder and liquid detergents
recommended for colours can be used
at dosages recommended for heavily
Heavily Soiled
Normally Soiled
Soiling Level
Lightly Soiled
soiled clothes. It is recommended to
use powder detergents to clean clay
and soil stains and the stains that are
sensitive to bleaches. Use detergents
without bleach.
Powder and liquid detergents
recommended for colours can be used
at dosages recommended for normally
soiled clothes. Use detergents without
bleach.
Powder and liquid detergents
recommended for colours can be used
at dosages recommended for lightly
soiled clothes. Use detergents without
bleach.
Dark colours
(Recommended temperature range
based on soiling level: cold -40 °C)
Liquid detergents suitable for colours
Heavily Soiled
Normally Soiled
Soiling Level
Lightly Soiled
and dark colours can be used at
dosages recommended for heavily
soiled clothes.
Liquid detergents suitable for colours
and dark colours can be used at
dosages recommended for normally
soiled clothes.
Liquid detergents suitable for colours
and dark colours can be used at
dosages recommended for lightly
soiled clothes.
Delicates/Woollens/Silks
(Recommended temperature range
based on soiling level: cold -30 °C)
Prefer liquid detergents produced
Heavily Soiled
Normally Soiled
Soiling Level
Lightly Soiled
for delicate clothes. Woollen and silk
clothes must be washed with special
woollen detergents.
Prefer liquid detergents produced
for delicate clothes. Woollen and silk
clothes must be washed with special
woollen detergents.
Prefer liquid detergents produced
for delicate clothes. Woollen and silk
clothes must be washed with special
woollen detergents.
If the product does not contain a liquid detergent
cup:
• Do not use liquid detergent for the prewash in a
programme with prewash.
• Liquid detergent stains your clothes when used with
Delayed Start function. If you are going to use the
Delayed Start function, do not use liquid detergent.
Using gel and tablet detergent
Apply the following instructions when using tablet, gel
and similar detergents.
• If the gel detergent thickness is fluidal and your
machine does not contain a special liquid detergent
cup, put the gel detergent into the main wash
detergent compartment during first water intake.
If your machine contains a liquid detergent cup,
fill the detergent into this cup before starting the
programme.
• If the gel detergent thickness is not fluidal or in the
shape of capsule liquid tablet, put it directly into the
drum before washing.
• Put tablet detergents into the main wash
compartment (compartment nr. "2") or directly into
the drum before washing.
NOTE : Tablet detergents may leave residues
in the detergent compartment. If you encounter
C
such a case, place the tablet detergent between
the laundry, close to the lower part of the drum in
future washings.
NOTE : Use the tablet or gel detergent without
selecting the prewash function.
Using starch
• Add liquid starch, powder starch or the fabric dye
into the softener compartment.
• Do not use softener and starch together in a washing
cycle.
• Wipe the inside of the machine with a damp and
clean cloth after using starch.
Using bleaches
• Select a programme with prewash and add the
bleaching agent at the beginning of the prewash.
Do not put detergent in the prewash compartment.
As an alternative application, select a programme
with extra rinse and add the bleaching agent while
the machine is taking water from the detergent
compartment during first rinsing step.
• Do not use bleaching agent and detergent by mixing
them.
• Use just a little amount (approx. 50 ml) of bleaching
agent and rinse the clothes very well as it causes
skin irritation. Do not pour the bleaching agent onto
the clothes and do not use it for coloured clothes.
• When using oxygen based bleaches, select a
programme that washes at a lower temperature.
• Oxygen based bleaches can be used together with
detergents; however, if its thickness is not the same
with the detergent, put the detergent first into the
compartment nr. "2" in the detergent drawer and
wait until the detergent flows while the machine is
taking in water. Add the bleaching agent from the
same compartment while the machine is still taking
in water.
Using limescale remover
• When required, use limescale removers
manufactured specifically for washing machines only.
10 / EN
Washing Machine / User’s Manual
4 Operating the product
4.1 Control panel
1 2
1 - Programme Selection knob (Uppermost position
On / Off)
2 - Delayed Start Indicator
3 - Programme Follow-up indicator
3
4567
4 - Start / Pause button
5 - Auxiliary Function buttons
6 - Spin Speed Adjustment button
7 - Temperature Adjustment button
4.2 Preparing the machine
1.Make sure that the hoses are connected tightly.
2.Plug in your machine.
3.Turn the tap on completely.
4.Place the laundry in the machine.
5.Add detergent and fabric softener.
4.3 Programme selection and
tips for efficient washing
1. Select the programme suitable for the type, quantity
and soiling degree of the laundry in accordance with
the "Programme and consumption table" and the
temperature table below.
2.Select the desired programme with the Programme
Selection button.
4.4 Main programmes
Depending on the type of fabric, use the following main
programmes.
• Cottons
Use this programme for your cotton laundry (such
as bed sheets, duvet and pillowcase sets, towels,
bathrobes, underwear, etc.). Your laundry will be
washed with vigorous washing action for a longer
washing cycle.
• Synthetics
Use this programme to wash your synthetic clothes
(shirts, blouses, synthetic/cotton blends, etc.). It
washes with a gentle action and has a shorter washing
cycle compared to the Cotton programme.
For curtains and tulle, use the Synthetic 40°C
programme with prewash and anti-creasing functions
selected. As their meshed texture causes excessive
foaming, wash the veils/tulle by putting little amount of
detergent into the main wash compartment. Do not put
detergent in the prewash compartment.
• Woollens
Use this programme to wash your woolen clothes.
Select the appropriate temperature complying with the
tags of your clothes. Use appropriate detergents for
woollens.
“The wool wash cycle of this machine has
been approved by The Woolmark Company
for the washing of machine washable wool
products provided that the products are washed
according to the instructions on the garment
label and those issued by the manufacturer of
this washing machine. M14095”
“In UK, Eire, Hong Kong and India the
Woolmark trade mark is a Certification trade
mark.”
4.5 Additional programmes
For special cases, additional programmes are available
in the machine.
Additional programmes may differ according to the
model of the machine.
C
• Cottons Eco
By washing normally soiled cotton and linen laundry
in this programme, you can ensure higher energy and
water efficiency than other cotton programmes do.
Actual water temperature may be different from the
stated wash temperature. While doing the laundry at
lesser amounts (e.g. half capacity or less) duration
of the program may reduce automatically at the later
stages of the program. In this case, energy and
water consumption will reduce for a more economic
wash. This feature is provided in the models with the
remaining time indicator.
11 / EN
Washing Machine / User’s Manual
• BabyProtect
This is a long lasting programme which you may
use for your laundry for which you require an antiallergic and hygienic washing at high temperature with
intensive and long washing cycle.
• Gentle Care 20°
You can wash your delicate clothes in this programme.
It washes with a gentler action without any interim
spins compared to the Synthetics programme. It should
be used for clothes for which delicate washing is
recommended.
• Hand wash 20°
Use this programme to wash your woolen/delicate
clothes that bear “not machine- washable” tags and for
which hand wash is recommended. It washes laundry
with a very gentle washing action to not to damage
clothes.
• Daily Xpress
Use this programme to wash your lightly soiled cotton
clothes in a short time.
• Xpress Super Short
Use this programme to wash your little amount of lightly
soiled cotton clothes in a short time. Your clothes will be
washed at 30 °C in a short time like 14 minutes.
• Dark Care
Use this programme to wash your dark coloured
laundry or the laundry that you do not want it get
faded. Washing is performed with little mechanic action
and at low temperatures. It is recommended to use
liquid detergent or woolen shampoo for dark coloured
laundry.
• Mix 40
Use this programme to wash your cotton and synthetic
clothes together without sorting them.
• Shirts
Use this programme to wash the shirts made of cotton,
synthetic and synthetic blended fabrics together.
4.7 Temperature selection
Whenever a new programme is selected, the maximum
temperature for the selected programme appears on
the temperature indicator.
To decrease the temperature, press the Temperature
Adjustment button. Temperature will decrease gradually.
If the programme has not reached the heating
step yet, you can change the temperature without
C
switching the machine to Pause mode.
4.8 Speed selection
Whenever a new programme is selected, the
recommended spin speed of the selected programme
is displayed on the spin speed indicator.
To decrease the spin speed, press the Spin Speed
Adjustment button. Spin speed decreases gradually.
Then, depending on the model of the product,
"Rinse Hold" and "No Spin" options appear on the
display. See "Auxiliary function selection" section for
explanations of these options.
Rinse Hold
If you are not going to unload your clothes immediately
after the programme completes, you can use rinse hold
function to keep your laundry in the final rinsing water
in order to prevent them from getting wrinkled when
there is no water in the machine. Press Start / Pause
button after this process if you want to drain the water
without spinning your laundry. Programme will resume
and complete after draining the water.
If you want to spin the laundry held in water, adjust the
Spin Speed and press Start / Pause button. Program
resumes. Water is drained, laundry is spun and the
programme is completed.
If the programme has not reached the spinning
step yet, you can change the speed without
C
switching the machine to Pause mode.
• Sports
Use this programme to wash your garments that are
worn for a short time such as sportswear. It is suitable
to wash little amount of cotton / synthetic blended
garments.
4.6 Special programmes
For specific applications, select any of the following
programmes.
• Rinse
Use this programme when you want to rinse or starch
separately.
• Spin + Drain
Use this programme to apply an additional spin cycle
for your laundry or to drain the water in the machine.
Before selecting this programme, select the desired
spin speed and press Start / Pause button. First, the
machine will drain the water inside of it. Then, it will
spin the laundry with the set spin speed and drain the
water coming out of them.
If you wish to drain only the water without spinning your
laundry, select the Pump+Spin programme and then
select the No Spin function with the help of Spin Speed
Adjustment button. Press Start / Pause button.
Use lower spin speeds for delicate laundries.
C
12 / EN
Washing Machine / User’s Manual
4.9 Programme and consumption table
EN
2
Auxiliary functions
Programme
Max. Load (kg)
Programme Duration (~min)
Water Consumption (l)
Energy Consumption (kWh)
Max. Speed***
Prewash
60** 6 196 45 0.94 1000 40-60
Cottons Eco
Cottons
Synthetics
Daily Xpress
Xpress Super Short 30 2 14 40 0.11 1000 Cold-30
Sports 40 3 101 48 0.45 800 • • Cold-40
Hand Wash 20 20 1 43 30 0.15 600 20
Woollens 40 1.5 60 40 0.30 600 Cold-40
Dark Care 40 2.5 107 58 0.45 800 Cold-40
Shirts 60 2.5 104 55 0.90 600 • • Cold-60
Mix40 40 3 115 45 0.50 800 • • Cold-40
BabyProtect 90 6 165 85 1.90 1000 • 30-90
GentleCare 20 20 2.5 75 45 0.15 600 20
60** 3 176 34 0.63 1000 40-60
40** 3 166 34 0.63 1000 40-60
90 6 147 66 2.25 1000 • • Cold-90
60 6 118 66 1.45 1000 • • Cold-90
40 6 98 66 0.85 1000 • • Cold-90
60 2.5 116 45 0.90 800 • • Cold-60
40 2.5 106 45 0.42 800 • • Cold-60
90 6 88 55 1.90 1000 Cold-90
60 6 58 55 1.00 1000 Cold-90
30 6 28 55 0.20 1000 Cold-90
Temperature
Quick Wash
• : Selectable
* : Automatically selected, not cancellable.
** : Energy Label programme (EN 60456 Ed.3)
*** : If maximum spin speed of the machine is lower then this value, you can only select up to the maximum spin speed.
- : See the programme description for maximum load.
** “Cotton eco 40°C and Cotton eco 60°C are standard programmes.” These programmes are known as '40°C
cotton standard programme' and '60°C cotton standard programme' and shown on the panel
C
13 / EN
with
Water and power consumption may vary subject to the changes in water pressure, water hardness and
temperature, ambient temperature, type and amount of laundry, selection of auxiliary functions and spin speed,
and changes in electric voltage.
You can see the washing time of the programme you have selected on the display of the machine. It is normal
that small differences may occur between the time shown on the display and the real washing time.
The auxiliary functions in the table may vary according to the model of your machine.
“Selectability of auxiliary functions might be changed by the manufacturer. New selectabilities might be added
or existing ones might be removed.”
“The spin speed of your machine may vary among the programmes, however this speed cannot exceed the
max. spin speed of your machine.”
symbols.
Washing Machine / User’s Manual
4.10 Auxiliary function selection
Select the required auxiliary functions before starting
the program. Furthermore, you may also select or
cancel auxiliary functions that are suitable to the
running programme without pressing the Start / Pause
button when the machine is operating. For this, the
machine must be in a step before the auxiliary function
you are going to select or cancel.
If the auxiliary function cannot be selected or canceled,
light of the relevant auxiliary function will blink 3 times
to warn the user.
Some functions cannot be selected together. For
example, Prewash and Quick Wash.
C
If a second auxiliary function conflicting with the
first one is selected before starting the machine,
the function selected first will be cancelled and
the second auxiliary function selection will remain
active. For example, if you want to select Quick
Wash after you have selected the Prewash,
Prewash will be cancelled and Quick Wash will
remain active.
Auxiliary function that is not compatible with the
program cannot be selected. (See "Programme and
consumption table")
Auxiliary Function buttons may vary according to the
model of the machine.
• Prewash
A Prewash is only worthwhile for heavily soiled
laundry. Not using the Prewash will save energy, water,
detergent and time.
Prewash without detergent is recommended for
tulle and curtains.
C
• Quick Wash
This function can be used in Cottons and Synthetics
programmes. It decreases the washing times for lightly
soiled laundries and also the number of rinsing steps.
When you select this function, load your machine
with half of the maximum laundry specified in the
C
programme table.
Delayed Start (In some models only)
With the Delayed Start function the startup of the
programme may be delayed up to 3, 6 or 9 hours.
Do not use liquid detergents when you set
Delayed Start! There is the risk of staining of the
C
clothes.
Open the loading door, place the laundry and put
detergent, etc. Select the washing programme,
temperature, spin speed and, if required, the auxiliary
functions. Set the desired time by pressing the Delayed
Start button. When the button is pressed once, 3 hours
delayed start is selected. When the same button is
pressed again, 6 hours delay is selected, and when it
is pressed for the third time, 9 hours delayed start is
selected. If you press the Delayed Start button once
again, Delayed Start function will be canceled. Press
Start / Pause button. Previous delayed start time light
turns off and next delayed start time light turns on
after every 3 hours. At the end of the countdown,
all delayed start lights will turn off and the selected
programme will start.
Additional laundry may be loaded during the
delayed start period.
C
Changing the Delayed Start period
Press Delayed Start button. Every time the button is
pressed, the period will change in 3-hour increments
and the light of the selected delayed start time will turn
on.
Canceling the Delayed Start function
If you want to cancel the delayed start countdown and
start the programme immediately:
Set the Delayed Start period to zero (all delayed
start period lights will turn off) or turn the Programme
Selection knob to any programme. Thus, Delayed Start
function will be canceled. The End/Cancel light flashes
continuously. Then, select the programme you want
to run again. Press Start / Pause button to start the
programme.
4.11 Starting the programme
Press Start / Pause button to start the programme.
Programme follow-up light showing the startup of the
programme will turn on.
If no programme is started or no key is pressed
within 1 minute during programme selection
C
process, the machine will switch to Pause mode
and the illumination level of the temperature,
speed and loading door indicator lights will
decrease. Other indicator lights and indicators will
turn off. Once the Programme Selection knob is
rotated or any button is pressed, indicator lights
and indicators will turn on again.
4.12 Child Lock
Use child lock function to prevent children from
tampering with the machine. Thus you can avoid any
changes in a running programme.
If the Programme Selection knob is turned when
the Child Lock is active, “Con” appears on the
C
display. The Child Lock does not allow any change
in the programmes and the selected temperature,
speed and auxiliary functions.
Even if another programme is selected with the
Programme Selection knob while the Child Lock
C
is active, previously selected programme will
continue running.
When the Child Lock is active and the machine
is running, you can switch the machine to Pause
C
mode without deactivating the Child Lock by
turning the Programme Selection knob to On / Off
position. When you turn the Programme Selection
knob afterwards, the programme will resu
To activate the Child Lock:
Press and hold 1st and 2nd Auxiliary Function buttons
for 3 seconds. The lights on the 1st and 2nd Auxiliary
Function buttons will flash while you keep the buttons
pressed for 3 seconds.
14 / EN
Washing Machine / User’s Manual
Loading...